Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 16575C 1.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.

Install the No. 1 water hose clamp bracket to the timing chain case assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 88451B 4.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 25709E 5.INSTALL NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 4 vacuum transmitting pipe sub-assembly to the cylinder block sub-assembly with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 25708 6.INSTALL NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 3 vacuum transmitting pipe sub-assembly to the cylinder head sub-assembly and cylinder block sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 4 vacuum transmitting hose sub-assembly to the No. 3 vacuum transmitting pipe sub-assembly.


Hide 25707 7.INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 2 vacuum transmitting pipe sub-assembly to the cylinder block sub-assembly and oil pan sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25706 8.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 1 vacuum transmitting pipe sub-assembly to the cylinder head sub-assembly and cylinder block sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 2 vacuum transmitting hose sub-assembly to the No. 3 vacuum transmitting pipe sub-assembly.


c.

Connect the No. 1 vacuum transmitting hose sub-assembly to the vacuum pump assembly.


Hide 25804A 9.INSTALL VACUUM SWITCHING VALVE SUB-ASSEMBLY (for Engine Mounting)

Hide 16620 10.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16603 11.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16304 12.INSTALL WATER OUTLET SUB-ASSEMBLY

a.

Install a new gasket and the water outlet sub-assembly to the timing chain cover sub-assembly with the 4 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16207 13.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 2 water by-pass pipe sub-assembly to the engine water pump assembly and water inlet with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 3 water by-pass hose to the water outlet sub-assembly, and slide the clamp to secure the hose.


Hide 15350 14.INSTALL OIL PRESSURE SWITCHING VALVE ASSEMBLY (w/ 2 Stage Hydraulic Switching Oil Pump System)

Hide 83520 15.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY (w/ 2 Stage Hydraulic Switching Oil Pump System)

Hide 83530 16.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY (w/o 2 Stage Hydraulic Switching Oil Pump System)

Hide 15407 17.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17141 18.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 17141 21.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 87101 23.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A354088E02
1.313,0.292 1.458,0.458 0.146,0.167 10 true 2 1.354,1.698 1.5,1.865 0.146,0.167 10 false 3 2.927,1.406 3.073,1.573 0.146,0.167 10 false 1 2.844,0.615 3,0.802 0.156,0.188 10 true 4

Temporarily install the No. 1 viscous heater bracket sub-assembly to the cylinder block sub-assembly and timing chain cover sub-assembly with the 4 bolts.


b.

Tighten the 4 bolts in the sequence shown in the illustration to install the No. 1 viscous heater bracket sub-assembly.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 16268 25.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe to the timing chain cover sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the No. 1 water by-pass pipe.



Hide 12361 27.INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a.

Install the front engine mounting insulator RH to the front No. 1 engine mounting bracket RH with the nut.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


b.

Connect the No. 3 vacuum transmitting hose sub-assembly to the front No. 1 engine mounting bracket RH.


Hide 89463C 28.INSTALL NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 17291 29.INSTALL TURBINE OUTLET ELBOW (w/o EGR Cooler)

a.

Set a new gasket and the turbine outlet elbow to the turbocharger sub-assembly.


b.

Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow with the 3 bolts.


c.
A407026C01
2.448,0.615 2.281,0.417 2.281,0.417 2.177,0.417 false 2.677,1.365 2.677,1.646 true 1.99,0.333 2.208,0.5 0.219,0.167 10 false *1 2.271,1.188 2.479,1.344 0.208,0.156 10 false *2 2.896,1.302 3.115,1.458 0.219,0.156 10 false *3 2.635,1.667 2.854,1.833 0.219,0.167 10 false *4 0.25,1.792 0.563,1.969 0.313,0.177 10 false 90°
*1 Exhaust Pipe Clamp
*2 Turbine Outlet Elbow
*3 Turbocharger Sub-assembly
*4 Gasket


Install a new exhaust pipe clamp to the turbine outlet elbow with a new nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.
A461325

Temporarily install the exhaust pipe support stay to the turbine outlet elbow with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.
A443334N01
2.083,1.188 2.24,1.385 0.156,0.198 10 true 1 1.24,1.667 1.396,1.865 0.156,0.198 10 true 2 0.563,1.281 0.708,1.438 0.146,0.156 10 true 3

Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 25051 30.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)

Hide 31.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/o DPF)

a.

w/o EGR Cooler:

i.

Temporarily install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow with the bolt and 2 new nuts.


ii.
A461326

Temporarily install the No. 2 exhaust pipe support stay to the turbine outlet elbow with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


iii.
A443333N01
0.854,0.083 0.979,0.25 0.125,0.167 10 true 1 0.719,1.573 0.854,1.729 0.135,0.156 10 true 2 2.896,1.76 3.021,1.927 0.125,0.167 10 true 3

Tighten the bolt and 2 nuts and install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)




Hide 32.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/ DPF)

Hide 89463C 33.CONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 17271 34.INSTALL NO. 1 TURBO INSULATOR (w/o DPF)

a.

w/o EGR Cooler:

Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



Hide 17167 36.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o DPF)

a.

w/o EGR Cooler:

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



Hide 17167 37.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 89467B 38.INSTALL AIR FUEL RATIO SENSOR (w/ DPF)

Hide 17168 39.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)

Hide 16281 41.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.

Connect the No. 4 water by-pass hose to the No. 1 injector holder, and slide the clamp to secure the hose.


Hide 16282 42.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.

Attach the clamp and install the No. 5 water by-pass hose to the No. 1 water hose clamp bracket.


b.

Connect the No. 5 water by-pass hose to the No. 1 injector holder and water outlet sub-assembly, and slide the 2 clamps to secure the hose.


Hide 12229 44.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

Hide 12261 45.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

Hide 89422C 46.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 88431 47.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

NOTICE:

Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A354094

Temporarily install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 2 bolts.

HINT:

Temporarily install the No. 1 compressor mounting bracket with the 2 bolts so that the No. 1 compressor mounting bracket can be moved by hand.



b.
A354095E02
1.115,3.521 1.302,3.677 0.188,0.156 10 true *a 2.625,3.521 2.813,3.677 0.188,0.156 10 true *a 3.198,3.531 3.385,3.688 0.188,0.156 10 true *a 1.875,4.427 2.063,4.583 0.188,0.156 10 false *b 2.458,4.427 2.646,4.583 0.188,0.156 10 false *b 0.521,2.677 0.708,2.833 0.188,0.156 10 false *c 0.771,1.469 0.896,1.646 0.125,0.177 10 true A

Push the No. 1 compressor mounting bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

Text in Illustration
*a No Clearance
*b Push
*c Front

HINT:

Make sure there is no clearance between the cylinder block sub-assembly and No. 1 compressor mounting bracket as shown in the illustration.



c.
A354096E01
2.726,1.183 2.93,1.42 0.205,0.237 2.765,1.225 2.907,1.382 0.141,0.158 10 3 2.966,0.478 3.171,0.715 0.205,0.237 3.006,0.52 3.147,0.678 0.141,0.158 10 2 0.973,0.382 1.177,0.619 0.205,0.237 1.03,0.424 1.171,0.582 0.141,0.158 10 1

Uniformly tighten the 3 bolts in the order shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 16025 48.INSTALL NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install a new gasket and the No. 5 water by-pass pipe sub-assembly to the cylinder block sub-assembly with the 3 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the No. 5 water by-pass pipe sub-assembly.



Hide 23300 49.INSTALL FUEL FILTER ASSEMBLY

a.

Install the fuel filter assembly to the cylinder block sub-assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 51.INSTALL HOSE BRACKET

a.

Install the hose bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19850 52.INSTALL GLOW PLUG ASSEMBLY

Hide 19871 53.INSTALL NO. 1 GLOW PLUG CONNECTOR

Hide 23810A 54.INSTALL COMMON RAIL ASSEMBLY

Hide 23701 55.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 56.TIGHTEN INJECTOR ASSEMBLY

Hide 23701 57.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 58.INSTALL WIRING HARNESS CLAMP BRACKET

a.
A354083E02
0.729,0.563 0.885,0.74 0.156,0.177 10 true A 2.313,0.677 2.469,0.833 0.156,0.156 10 true B 2.958,0.146 3.115,0.302 0.156,0.156 10 false B

for LHD:

Install the 3 wiring harness clamp brackets to the cylinder head cover sub-assembly with the 3 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.
A354084E03
0.948,0.667 1.115,0.823 0.167,0.156 10 true A 3.052,0.844 3.219,1 0.167,0.156 10 true B

for RHD:

Install the 2 wiring harness clamp brackets to the cylinder head cover sub-assembly with the 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 60.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23770 62.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23804C 63.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 23804D 65.INSTALL NO. 4 FUEL PIPE (w/o DPF)

Hide 23804D 66.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23271H 67.INSTALL NO. 1 FUEL HOSE

Hide 23273H 68.INSTALL NO. 2 FUEL HOSE

Hide 23243B 69.INSTALL FUEL PUMP MOTOR WIRE

Hide 22803 70.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 72.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23812D 73.INSTALL NO. 2 FUEL PIPE

a.

Install the No. 2 fuel pipe to the manifold stay with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.


Hide 11409 74.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25617 75.INSTALL EGR HOLE COVER PLATE (w/o EGR System)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the 2 EGR cooler hole plates to the intake manifold and exhaust manifold with 4 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 25624 76.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY (w/o EGR System)

a.

Temporarily install the EGR valve adapter sub-assembly to the intake manifold with the 4 bolts.


b.
A398418N01
0.594,1.948 0.729,2.104 0.135,0.156 10 true 1 2.771,1.854 2.906,2.01 0.135,0.156 10 true 2 3.104,0.719 3.24,0.875 0.135,0.156 10 true 3 0.156,0.542 0.292,0.698 0.135,0.156 10 true 4

Tighten the 4 bolts in the order shown in the illustration.

NOTICE:

Make sure to tighten the bolts in the order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 77.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

a.
A365517N01
0.479,0.646 0.646,0.802 0.167,0.156 10 true 4 2.781,1.573 2.969,1.76 0.188,0.188 10 true 3 2.177,1.885 2.365,2.063 0.188,0.177 10 true 2 0.938,1.948 1.115,2.125 0.177,0.177 10 true 1

Temporarily install the EGR valve adapter sub-assembly with electric EGR control valve assembly to the intake manifold with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

NOTICE:

Make sure to tighten the bolts in the order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25800 78.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Cooler)

Hide 16209 79.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

for Cold Area Specification Vehicles:

Attach the clamp and connect the No. 11 water by-pass hose to the No. 2 fuel pipe.


c.

Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.


d.

Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


e.

w/ Urea SCR System:

Install the No. 17 water by-pass hose to the No. 1 EGR pipe sub-assembly and No. 4 water by-pass pipe sub-assembly, and slide the 2 clamps to secure the hose.


Hide 25804 80.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 25601 81.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the No. 1 EGR pipe sub-assembly to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly with the bolt and 4 new nuts.

Torque:
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for nut : 29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 16206B 82.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.

Install the No. 3 water by-pass pipe sub-assembly to the EGR valve adapter sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

w/ EGR System:

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


c.

Connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 16206B 83.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 25612 84.INSTALL NO. 2 EGR PIPE (w/ EGR System)

Hide 25625 85.INSTALL EGR VALVE BRACKET (w/ EGR System)

Hide 25734 90.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)

Hide 25733A 91.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)

Hide 89481B 95.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 16278 96.INSTALL NO. 2 WATER BY-PASS PIPE

Hide 26100G 97.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 82121 99.INSTALL ENGINE WIRE

Hide 12632 100.INSTALL NO. 2 ENGINE COVER BRACKET (w/o Urea SCR System)

Hide 12633 101.INSTALL NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)