When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.
1.CHECK INJECTOR COMPENSATION CODE
13053
2.INSTALL NO. 3 AND NO. 4 CAMSHAFTS
If replacing a camshaft with a new one, make a matchmark on the new camshaft in the same place as the old camshaft. Determine the matchmark placement by using the dot mark as a reference point and counting the number of gear teeth from the dot mark to the matchmark as shown in the illustration.
w/o Intercooler:
When replacing the No. 4 camshaft with a new one, install a new hole plug (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).
Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.
Apply engine oil to the rollers of the valve rocker arms and the camshaft housing of the cylinder head.
Install the No. 3 and No. 4 camshafts.
Apply engine oil to the camshaft journals, lobes, thrust portion and gears.
Align the matchmarks of the No. 3 and No. 4 camshaft timing gears as shown in the illustration.
Place the camshafts into the cylinder head.
Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.
Install the No. 4 camshaft bearing cap.
Align the No. 4 camshaft bearing cap and the ring pins of the No. 5 camshaft bearing cap.
Temporarily install the 4 bolts by hand.
Install the No. 3 camshaft bearing caps.
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.
Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.
Temporarily install the No. 3 and No. 4 camshaft oil feed pipes with the 8 bolts by hand.
If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.
The pipe is bent on the intake side, and straight on the exhaust side.
Temporarily install the 2 union bolts by hand.
Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.
Tighten the 2 union bolts.
Remove the service bolt from the No. 4 camshaft timing gear.
Do not drop the bolt into the engine.
If the bolt is difficult to remove, rotate the camshaft and remove the bolt. Then realign the matchmarks of the No. 3 and No. 4 camshaft timing gears.
Temporarily install the No. 2 timing chain and No. 2 camshaft timing sprocket to the No. 3 camshaft with the 2 bolts.
Using SST, hold the No. 2 camshaft timing sprocket. Tighten the 2 bolts.
Rotate the crankshaft pulley clockwise so that the 2 remaining pump drive shaft gear bolts can be installed.
Temporarily install the 2 bolts to the No. 3 camshaft.
Using SST, hold the No. 2 camshaft timing sprocket. Tighten the 2 bolts.
Remove the hexagon wrench from the No. 2 chain tensioner.
Remove the adhesive from the threads of the taper screw plug and the bolt hole of the timing gear case.
Apply adhesive to 3 or more threads of the taper screw plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Using a 10 mm hexagon wrench, install the taper screw plug.
13511
3.INSTALL NO. 1 AND NO. 2 CAMSHAFTS
If replacing a camshaft with a new one, make a matchmark on the new camshaft in the same place as the old camshaft. Determine the matchmark placement by using the dot mark as a reference point and counting the number of gear teeth from the dot mark to the matchmark as shown in the illustration.
Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.
Apply engine oil to the rollers of the valve rocker arms and the camshaft housing of the cylinder head.
Install the No. 1 and No. 2 camshafts.
Apply engine oil to the camshaft journals, lobes, thrust portion and gears.
Align the matchmarks of the No. 1 and No. 2 camshaft timing gears as shown in the illustration.
Place the 2 camshafts into the cylinder head.
Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.
Install the No. 1 camshaft bearing cap.
Align the No. 1 camshaft bearing cap and the ring pins of the No. 2 camshaft bearing cap.
Temporarily install the 4 bolts by hand.
Install the No. 3 camshaft bearing caps.
Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.
Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.
Temporarily install the No. 1 and No. 2 camshaft oil feed pipes with the 8 bolts by hand.
If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.
The pipe is bent on the intake side, and straight on the exhaust side.
Temporarily install the 2 union bolts by hand.
Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.
Tighten the 2 union bolts.
Remove the service bolt from the No. 1 camshaft timing gear.
Do not drop the bolt into the engine.
If the bolt is difficult to remove, rotate the camshaft and remove the bolt. Then realign the matchmarks of the No. 1 and No. 2 camshaft timing gears.
Temporarily install the No. 1 timing chain and No. 1 camshaft timing sprocket to the No. 2 camshaft.
Temporarily install the pump drive shaft gear with the 2 bolts.
Using SST, hold the pump drive shaft gear. Tighten the 2 bolts.
Rotate the crankshaft clockwise so that the 2 remaining pump drive shaft gear bolts can be installed.
Temporarily install the 2 bolts to the pump drive shaft gear.
Using SST, hold the pump drive shaft gear. Tighten the 2 bolts.
Remove the hexagon wrench.
Remove the adhesive from the threads of the taper screw plug and the bolt hole of the timing gear case.
Apply adhesive to 3 or more threads of the taper screw plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Using a 10 mm hexagon wrench, install the taper screw plug.
4.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION
Rotate the crankshaft clockwise 3 times or more, and check that the timing marks of the camshafts (1 dot mark each) align. If the timing marks of the camshafts do not align, repeat the "Install No. 3 and No. 4 Camshafts" and "Install No. 1 and No. 2 Camshafts" procedures.
23670
5.INSTALL FUEL INJECTOR LH
23670
6.INSTALL FUEL INJECTOR RH
11214
7.INSTALL NOZZLE HOLDER GASKET LH
11202
8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
23681C
9.INSTALL NOZZLE HOLDER SEAL LH
12270
10.INSTALL OIL SEPARATOR ASSEMBLY
11213
11.INSTALL NOZZLE HOLDER GASKET RH
11201
12.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
23681C
13.INSTALL NOZZLE HOLDER SEAL RH
11225
14.INSTALL CYLINDER HEAD COVER SILENCER LH (w/ Intercooler)
11224
15.INSTALL CYLINDER HEAD COVER SILENCER RH (w/ Intercooler)
12263
16.CONNECT NO. 3 VENTILATION HOSE
12262
17.CONNECT NO. 2 VENTILATION HOSE
29300
18.INSTALL VACUUM PUMP ASSEMBLY (w/ Intercooler)
25706
19.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY
25860
20.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ Intercooler)
21.INSTALL NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)
16630H
22.INSTALL NO. 2 IDLER PULLEY (w/ Viscous Heater)
23702
23.INSTALL INJECTION PIPE RH
24.CONNECT NO. 2 ENGINE WIRE
23801L
25.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
23820A
26.INSTALL COMMON RAIL ASSEMBLY LH
23701
27.INSTALL INJECTION PIPE LH
23706
28.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY
23802E
29.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY
30.CONNECT ENGINE WIRE
RH side:
Install the engine wire harness protector with the 3 bolts labeled A.
Connect the 7 connectors.
Attach the wire harness clamp.
Install the wire harness bracket with the bolt labeled B.
Install the glow plug wire harness with the nut labeled C.
Attach the 5 wire harness clamps and connect the 4 connectors.
LH side:
Install the engine wire harness protector with the 2 bolts labeled A.
Connect the 8 connectors.
Install the wire harness bracket with the bolt labeled B.
for RHD:
Connect the wire harness with the wire harness clamp holder labeled C.
Attach the 3 wire harness clamps and connect the 2 connectors.
Attach the 3 wire harness clamps and connect the 4 connectors.
Connect the wire harness with the wire harness clamp holder labeled B.
Attach the ground wire clamp labeled A to the relay block side.
Install the ground wire to the body panel with the bolt.
Connect the 4 connectors to the injector driver.
Install the ground wire with the bolt.
Connect the wire harness holder to the relay block.
Connect the 4 connectors to the relay block.
Connect the wire harness with the wire harness clamp holder.
for RHD:
Connect the wire harness with the wire harness clamp holder.
Connect the ECM connector to the ECM.
Connect the wire harness with the wire harness clamp holder.
Attach the wire harness tab labeled A to the relay block.
Connect the 4 connectors to the relay block.
for LHD:
Connect the wire harness with the wire harness clamp holder.
Connect the ECM connector to the ECM.
Attach the wire harness tab labeled A to the relay block.
Connect the 4 connectors to the relay block.
23274D
31.CONNECT FUEL HOSE
16288
32.INSTALL NO. 4 WATER BY-PASS PIPE
16268M
33.INSTALL NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)
31489
34.INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transaxle)
17972
35.INSTALL AIR TUBE SUB-ASSEMBLY LH
31418
36.INSTALL CLUTCH HOSE (for Manual Transmission)
17971
37.INSTALL AIR TUBE SUB-ASSEMBLY RH
38.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
87209
39.CONNECT WATER HOSE SUB-ASSEMBLY
17806
40.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY
17364
41.INSTALL NO. 4 AIR TUBE
17342D
42.INSTALL NO. 2 AIR HOSE
17885
43.INSTALL NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY
17363K
44.INSTALL NO. 3 AIR TUBE
17341F
45.INSTALL NO. 1 AIR HOSE
46.INSTALL NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)
87120G
47.INSTALL VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)
87208
48.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
17973
49.INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)
17973
50.INSTALL NO. 1 COOL AIR INLET (w/o Intercooler)
17940D
51.INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)
16711
52.INSTALL FAN SHROUD WITH FAN
32942
53.INSTALL OIL COOLER TUBE (for Automatic Transmission)
16361A
54.INSTALL V-RIBBED BELT
55.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)
56.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)
57.INSTALL V-RIBBED BELT (w/ Viscous Heater)
44310
58.INSTALL VANE PUMP ASSEMBLY
16470
59.INSTALL RADIATOR RESERVOIR ASSEMBLY
44369A
60.INSTALL NO. 1 OIL RESERVOIR BRACKET
44360
61.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY
17861
62.INSTALL INTAKE AIR CONNECTOR
17881
63.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE
17705
64.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
82113
65.INSTALL NO. 3 ENGINE ROOM WIRE
67.BLEED AIR FROM FUEL SYSTEM
68.BLEED CLUTCH LINE
69.INSPECT FOR CLUTCH FLUID LEAK
28800N
70.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Connect the cables to negative (-) main battery and sub-battery battery terminals.
71.ADD ENGINE COOLANT
72.INSPECT FOR FUEL LEAK
73.INSPECT FOR OIL LEAK
74.INSPECT FOR COOLANT LEAK
75.WARM UP ENGINE
In order to bleed air from the chain tensioner, drive the vehicle with the engine at 3000 rpm for 60 seconds or more.
76.INSPECT FOR EXHAUST GAS LEAK
51405A
77.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53805
78.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
53806
79.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53739A
80.INSTALL FRONT FENDER APRON SEAL REAR LH
53737B
81.INSTALL FRONT FENDER APRON SEAL FRONT LH
53738A
82.INSTALL FRONT FENDER APRON SEAL REAR RH
53736G
83.INSTALL FRONT FENDER APRON SEAL FRONT RH
84.INSTALL FRONT WHEEL
12601E
85.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)
55781E
86.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53383
87.INSTALL HOOD TO COWL TOP SEAL
85211B
88.INSTALL FRONT WIPER ARM RH
85221B
89.INSTALL FRONT WIPER ARM LH
53882H
90.INSTALL FRONT FENDER MAIN SEAL RH
53883F
91.INSTALL FRONT FENDER MAIN SEAL LH
53292A
92.INSTALL UPPER RADIATOR SUPPORT SEAL
93.INSPECT ENGINE IDLE SPEED
94.INSPECT MAXIMUM ENGINE SPEED
95.CHECK ENGINE OIL LEVEL
96.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR