Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255570 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal*1 or clutch pedal*2 depressed.

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).

·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.



Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Power Supply Condition

·

IG Relay Monitor(Inside)

·

IG Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal*

·

Neutral SW/ Clutch SW

·

Starter Request Signal


Entry&Start
·

Immobiliser

·

S Code Check

·

L Code Check

·

Engine Start Request


Starting Control
·

Ignition

·

Starter SW

·

Shift Position P or N*


-

*: for Automatic Transmission


WIRING DIAGRAM

Refer to "System Diagram" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>SYSTEM DIAGRAM)

C388145E01
0.198,0.052 1.667,0.292 1.469,0.24 12 false for RHD: 2.208,1.135 2.583,1.333 0.375,0.198 10 false ECM 1.917,2.219 2.375,2.417 0.458,0.198 10 false STOP 0.5,2 1.583,2.198 1.083,0.198 10 false from Battery 2.792,3.052 3.917,3.417 1.125,0.365 10 false Stop Light Switch Assembly 2.792,4.792 4.333,5.156 1.542,0.365 10 false Stop Light Control Relay Assembly 4.938,4.802 7.083,5.167 2.146,0.365 10 false Transmission Floor Shift Assembly (Shift Lock Control Sub-assembly) 4.927,4.625 5.302,4.823 0.375,0.198 10 false E51 2.792,4.615 3.167,4.813 0.375,0.198 10 false A39 5.125,2.844 5.583,3.042 0.458,0.198 10 false E128 5.125,3.01 6.667,3.375 1.542,0.365 10 false Certification ECU (Smart Key ECU Assembly) 2.792,2.885 3.167,3.083 0.375,0.198 10 false A73 5.083,1.219 6.708,1.583 1.625,0.365 10 false Skid Control ECU (Master Cylinder Solenoid) 5.083,1.052 5.458,1.25 0.375,0.198 10 false A24 2.833,0.51 3.208,0.708 0.375,0.198 10 false A52 3.198,0.51 3.573,0.708 0.375,0.198 10 false A52 2.885,2.542 3.26,2.74 0.375,0.198 10 false GND 3.292,4.031 3.667,4.229 0.375,0.198 10 false STP 5.448,4.01 5.823,4.208 0.375,0.198 10 false STP 5.438,2.26 5.813,2.458 0.375,0.198 10 false STP1 3.469,2.271 3.625,2.469 0.156,0.198 10 false L 2.885,2.021 3.042,2.219 0.156,0.198 10 false B 5.438,0.51 5.813,0.708 0.375,0.198 10 false STP 2.875,0.75 3.188,0.948 0.313,0.198 10 false *1 3.26,0.75 3.573,0.948 0.313,0.198 10 false *2 2.854,0.302 3.167,0.5 0.313,0.198 10 false 36 3.24,0.302 3.552,0.5 0.313,0.198 10 false 13 2.438,0.5 2.813,0.698 0.375,0.198 10 false STP 5.167,0.385 5.323,0.583 0.156,0.198 10 false 7 5.167,2.146 5.323,2.344 0.156,0.198 10 false 2 3.708,2.146 3.865,2.344 0.156,0.198 10 false 2 3.719,3.885 3.875,4.083 0.156,0.198 10 false 2 2.635,2.406 2.792,2.604 0.156,0.198 10 false 3 2.615,1.896 2.771,2.094 0.156,0.198 10 false 1 5.177,3.896 5.333,4.094 0.156,0.198 10 false 6 0.417,4.875 1.729,5.073 1.313,0.198 10 false *1: for 1UR-FE 0.438,5.25 1.75,5.448 1.313,0.198 10 false *2: for 1VD-FTV

C348665E06
2.146,1.083 2.667,1.333 0.521,0.25 10 false ECM 2.396,0.5 2.917,0.75 0.521,0.25 10 false STP 3.24,4 3.76,4.25 0.521,0.25 10 false STP 5.438,3.979 5.958,4.229 0.521,0.25 10 false STP 5.427,2.24 5.948,2.458 0.521,0.219 10 false STP1 5.438,0.5 5.958,0.719 0.521,0.219 10 false STP 5.219,0.365 5.51,0.656 0.292,0.292 10 false 7 3.698,3.885 3.865,4.125 0.167,0.24 10 false 2 5.219,3.885 5.427,4.177 0.208,0.292 10 false 6 5.219,2.135 5.385,2.375 0.167,0.24 10 false 2 3.698,2.135 3.865,2.375 0.167,0.24 10 false 2 2.677,2.406 2.844,2.646 0.167,0.24 10 false 3 2.677,1.896 2.844,2.135 0.167,0.24 10 false 1 2.927,0.292 3.094,0.531 0.167,0.24 10 false 7 3.208,0.51 3.573,0.719 0.365,0.208 10 false A52 3.573,0.5 3.938,0.708 0.365,0.208 10 false A52 2.854,0.5 3.219,0.708 0.365,0.208 10 false A38 3.24,0.281 3.604,0.49 0.365,0.208 10 false 36 3.615,0.281 3.979,0.49 0.365,0.208 10 false 13 3.49,2.25 3.667,2.469 0.177,0.219 10 false L 2.885,2 3.063,2.219 0.177,0.219 10 false B 2.865,2.521 3.323,2.74 0.458,0.219 10 false GND 1.865,2.156 2.469,2.375 0.604,0.219 10 false STOP 0.51,2.01 1.531,2.229 1.021,0.219 10 false from Battery 2.885,0.688 3.115,0.938 0.229,0.25 10 false *1 3.25,0.688 3.479,0.938 0.229,0.25 10 false *2 3.594,0.688 3.823,0.938 0.229,0.25 10 false *3 0.146,3.667 1.948,4.031 1.802,0.365 10 false *1: for 3UR-FE and 1GR-FE with Automatic Transmission 0.146,4.427 1.885,4.792 1.74,0.365 10 false *2: for 1UR-FE and 1GR-FE with Manual Transmission 0.146,5.25 1.354,5.469 1.208,0.219 10 false *3: for 1VD-FTV 0.26,0.052 1.083,0.271 0.823,0.219 12 false for LHD: 2.719,2.979 3.854,3.323 1.135,0.344 10 false Stop Light Switch Assembly 2.719,2.854 3.083,3.063 0.365,0.208 10 false A73 5.25,1.208 6.938,1.552 1.688,0.344 10 false Skid Control ECU (Master Cylinder Solenoid) 5.26,1.073 5.625,1.281 0.365,0.208 10 false A24 5.281,2.969 6.958,3.313 1.677,0.344 10 false Certification ECU (Smart Key ECU Assembly) 5.292,2.833 5.656,3.042 0.365,0.208 10 false E128 4.927,4.708 7.125,5.052 2.198,0.344 10 false Transmission Floor Shift Assembly (Shift Lock Control Sub-assembly) 4.927,4.583 5.292,4.792 0.365,0.208 10 false E51 2.667,4.708 4.208,5.052 1.542,0.344 10 false Stop Light Control Relay Assembly 2.677,4.583 3.042,4.792 0.365,0.208 10 false A39

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly), ECM or ID code box (immobiliser code ECU), refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:

If the brake pedal*1 or clutch pedal*2 is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal*1 or clutch pedal*2 to illuminate the stop lights increases.

*1: for Automatic Transmission

*2: for Manual Transmission



PROCEDURE

1.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Press a switch of the electrical key transmitter sub-assembly.

OK:

The electrical key transmitter sub-assembly LED illuminates.




OK

2.READ VALUE USING GTS (KEY LOW BATTERY)

NG

11.INSPECT TRANSMITTER BATTERY
2.READ VALUE USING GTS (KEY LOW BATTERY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Low Battery Transmitter battery depleted/Yes or No Yes: Transmitter battery depleted
No: Transmitter battery not depleted
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).

OK:

"No" is displayed in the Data List.




OK

3.CHECK WAVE ENVIRONMENT

NG

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver.


OK:

Engine starts.




OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK ENGINE SWITCH CONDITION
4.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

for Automatic Transmission:

Move the shift lever to P.


c.

With the brake pedal released*1 or clutch pedal*2, check that pressing the engine switch causes the power source mode to change.

*1: for Automatic Transmission

*2: for Manual Transmission


Result
Result Proceed to
Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) and on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

B

C

D

5.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW
for Automatic Transmission:

Shift position (P and N)/ON or OFF


for Manual Transmission:

State of clutch pedal/ON or OFF


for Automatic Transmission:

ON: Shift lever in P or N

OFF: Shift lever in any position other than P or N


for Manual Transmission:

ON: Clutch pedal depressed

OFF: Clutch pedal released


for Automatic Transmission:
·

Use this item to determine whether the park/neutral position switch is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed.


for Manual Transmission:
·

Use this item to help determine if the clutch position switch is malfunctioning .

·

The engine cannot be started when this item is "OFF".



Starting Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift Position P or N Park/neutral position switch status/ON or OFF ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N
When malfunctioning, the engine will not crank.

OK:

The item in the Data List changes according to the shift position.


Result
Result Proceed to
OK A
NG for Automatic Transmission B
for Manual Transmission C



A

6.CHECK FOR DTC

B

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

14.INSPECT CLUTCH START SWITCH ASSEMBLY
6.CHECK FOR DTC
a.

Using the GTS, check for DTCs.

Result
Result Proceed to
DTCs are not output for Automatic Transmission A
for Manual Transmission B
Entry and start system (for Start Function) DTCs are output C



A

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)

B

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

C

7.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal/ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.



OK:

The item in the Data List changes when the brake pedal is depressed and released.




OK

8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
8.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status/ON or OFF
for Automatic Transmission:

ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held

OFF: After approximately 1 second. has elapsed, the engine switch is released


for Manual Transmission:

ON: With the clutch pedal depressed, the engine switch is pressed and held

OFF: After approximately 1 second has elapsed, the engine switch is released


·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.



NOTICE:

Check that the key warning light is displayed on the multi-information display on the combination meter assembly, and then press the engine switch.


OK:

The display changes in response to the operation of the engine switch.




OK

9.CHECK STEERING LOCK SYSTEM

NG

18.READ VALUE USING GTS (STARTER SW)
9.CHECK STEERING LOCK SYSTEM
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.




OK

10.CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)

NG

GO TO STEERING LOCK SYSTEM (PROBLEM SYMPTOMS TABLE)

10.CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

for Automatic Transmission:

Move the shift lever to P.


c.

Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

*1: for Automatic Transmission

*2: for Manual Transmission


HINT:

It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

11.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.




OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

12.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

A

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

B

C

D

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C45*1 or C46*2 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)



c.

Disconnect the C24 park/neutral position switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE
Tester Connection Condition Specified Condition
E128-10 (STAR) - C24-3 (B) Always Below 1 Ω
E128-10 (STAR) or C24-3 (B) - Body ground 10 kΩ or higher

except 3UR-FE
Tester Connection Condition Specified Condition
E128-10 (STAR) - C24-4 (B) Always Below 1 Ω
E128-10 (STAR) or C24-4 (B) - Body ground 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Remove the clutch start switch assembly.



b.

Inspect the clutch start switch assembly.


Result
Result Proceed to
OK A
NG for RHD B
for LHD C



A

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

B

REPLACE CLUTCH SWITCH ASSEMBLY

C

REPLACE CLUTCH SWITCH ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the e1*1 or A49*2 clutch start switch assembly connector.

*1: for RHD

*2: for LHD



c.

Disconnect the C45*1 or C46*2 ECM connector.

*1: for 1VD-FTV (for LHD) or 1GR-FE

*2: for 1VD-FTV (for RHD)



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
E128-10 (STAR) - e1-1 Always Below 1 Ω
E128-10 (STAR) or e1-1 - Body ground 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
E128-10 (STAR) - A49-1 Always Below 1 Ω
E128-10 (STAR) or A49-1 - Body ground 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)



b.

Disconnect the A24 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A73 stop light switch assembly connector.


e.

Disconnect the E51 shift lock control ECU connector.


f.

Disconnect the A39 stop light control relay assembly connector.


g.
U165455E01
0.156,0.114 0.342,0.273 0.186,0.158 10 *a 0.804,1.694 1.016,1.853 0.212,0.158 10 B 1.492,1.776 1.704,1.934 0.212,0.158 10 L 2.188,1.724 2.657,1.883 0.469,0.158 10 GND 1.298,1.297 1.121,1.762 1.121,1.762 0.986,1.762 false 1.779,1.292 1.982,1.793 1.982,1.793 2.139,1.793 false 1.602,0.148 2.015,0.306 0.413,0.158 10 A73 1.515,1.319 1.515,1.749 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-1 (B) - Body ground Always 11 to 14 V



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-2 (STP1) - A73-2 (L) Always Below 1 Ω
E128-2 (STP1) or A73-2 (L) - Body ground 10 kΩ or higher
A73-3 (GND) - Body ground Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


OK

17.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

18.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Get into the vehicle while carrying an electrical key transmitter sub-assembly and press the engine switch with the shift lever in P and brake pedal depressed to check if the Data List display changes.

Starting Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Starter SW Starter operation request/ON or OFF ON: Starter operation requested
OFF: Starter operation not requested
When malfunctioning, the engine will not crank.

OK:

The Data List item changes.




OK

19.INSPECT ST RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

19.INSPECT ST RELAY

OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE ST RELAY

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
U164307E01
0.179,2.094 0.368,2.253 0.189,0.158 10 *a 2.368,4.006 2.865,4.165 0.497,0.158 10 STA 0.594,4.013 1.090,4.172 0.497,0.158 10 STAR 1.533,3.533 1.272,4.074 1.272,4.074 1.098,4.074 false 1.886,3.537 2.162,4.091 2.162,4.091 2.315,4.091 false 1.514,2.258 1.927,2.416 0.413,0.158 10 E128

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A38 and C45*1 or A52 and C46*2 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)



c.

for Automatic Transmission:

Move the shift lever to P or N.


d.

for Manual Transmission:

Depress the clutch pedal.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-10 (STAR) - Body ground 20°C (68°F) 93.75 to 136.36 Ω
E128-12 (STA) - Body ground


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))

Result
Result Proceed to
OK A
NG for Automatic Transmission B
for Manual Transmission C



A

21.INSPECT STARTER ASSEMBLY

B

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

C

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
21.INSPECT STARTER ASSEMBLY

b.

Inspect the starter assembly .


Result
Result Proceed to
OK A
NG for 1UR-FE B
for 1GR-FE C
for 3UR-FE D
for 1VD-FTV E



A

22.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY )

B

C

D

E

22.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY )
a.

Remove the starter assembly from the vehicle to perform an inspection.



b.

Remove the ST relay.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 3UR-FE
Tester Connection Condition Specified Condition
D16-1 - Body ground Always 11 to 14 V
ST relay terminal 5 - Body ground

for 1UR-FE
Tester Connection Condition Specified Condition
D21-1 - Body ground Always 11 to 14 V
ST relay terminal 5 - Body ground

for 1GR-FE
Tester Connection Condition Specified Condition
D20-1 - Body ground Always 11 to 14 V
ST relay terminal 5 - Body ground

for 1VD-FTV
Tester Connection Condition Specified Condition
D13-1 - Body ground Always 11 to 14 V
ST relay terminal 5 - Body ground



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1VD-FTV
Tester Connection Condition Specified Condition
ST relay terminal 3 - D12-1 Always Below 1 Ω
ST relay terminal 3 or D12-1 - Body ground 10 kΩ or higher

except 1VD-FTV
Tester Connection Condition Specified Condition
ST relay terminal 3 - D2-1 Always Below 1 Ω
ST relay terminal 3 or D2-1 - Body ground 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C24 park/neutral position switch connector.


c.

Disconnect the C45*1 or C46*2 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE
Tester Connection Condition Specified Condition
E128-10 (STAR) - C24-3 (B) Always Below 1 Ω
E128-10 (STAR) or C24-3 (B) - Body ground 10 kΩ or higher

except 3UR-FE
Tester Connection Condition Specified Condition
E128-10 (STAR) - C24-4 (B) Always Below 1 Ω
E128-10 (STAR) or C24-4 (B) - Body ground 10 kΩ or higher




OK

24.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)
a.

Disconnect the C24 park/neutral position switch connector.


b.

Remove the ST relay.


c.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 3UR-FE
Tester Connection Condition Specified Condition
C24-8 (L) - ST relay terminal 2 Always Below 1 Ω
C24-8 (L) or ST relay terminal 2 - Body ground 10 kΩ or higher

except 3UR-FE
Tester Connection Condition Specified Condition
C24-5 (L) - ST relay terminal 2 Always Below 1 Ω
C24-5 (L) or ST relay terminal 2 - Body ground 10 kΩ or higher




OK

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-12 (STA) - ST relay terminal 2 Always Below 1 Ω
E128-12 (STA) or ST relay terminal 2 - Body ground 10 kΩ or higher




OK

26.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the e1*1 or A49*2 clutch start switch assembly connector.

*1: for RHD

*2: for LHD



c.

Disconnect the C45*1 or C46*2 ECM connector.

*1: for 1VD-FTV (for LHD) or 1GR-FE

*2: for 1VD-FTV (for RHD)



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
E128-10 (STAR) - e1-1 Always Below 1 Ω
E128-10 (STAR) or e1-1 - Body ground 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
E128-10 (STAR) - A49-1 Always Below 1 Ω
E128-10 (STAR) or A49-1 - Body ground 10 kΩ or higher




OK

28.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the e1*1 or A49*2 clutch start switch assembly connector.

*1: for RHD

*2: for LHD



b.

Remove the ST relay.


c.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for 1VD-FTV (for LHD) or 1GR-FE

*2: for 1VD-FTV (for RHD)



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
e1-2 - ST relay terminal 2 Always Below 1 Ω
e1-2 or ST relay terminal 2 - Body ground 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
A49-2 - ST relay terminal 2 Always Below 1 Ω
A49-2 or ST relay terminal 2 - Body ground 10 kΩ or higher




OK

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (CLUTCH START SWITCH ASSEMBLY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (CLUTCH START SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the E128 certification ECU (smart key ECU assembly) connector.


b.

Remove the ST relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-12 (STA) - ST relay terminal 2 Always Below 1 Ω
E128-12 (STA) or ST relay terminal 2 - Body ground 10 kΩ or higher




OK

30.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR