| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | RING PIN | - | ( ) |
- | - |
| *1 | CAMSHAFT HOUSING SUB-ASSEMBLY RH | *2 | CAMSHAFT HOUSING SUB-ASSEMBLY LH |
| ● | Non-reusable part | - | - |
| *1 | PLATE WASHER | *2 | CYLINDER HEAD SET BOLT |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| * | For use with ball joint lock nut wrench | - | - |
| *T1 | 1st: 90 (918, 66) 2nd: Turn 90° 3rd: Turn 90° |
- | - |
| *1 | NO. 2 CHAIN SUB-ASSEMBLY | *2 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY) |
| *3 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY) | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *1 | NO. 2 CHAIN SUB-ASSEMBLY | *2 | FUEL PUMP LIFTER HOUSING RH |
| *3 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY) | *4 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY) |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 39 | NO. 6 ENGINE COVER | 12616 | - | - | - |
| 40 | TIMING CHAIN COVER ASSEMBLY | 11310 | ( ) |
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *1 | NO. 1 IDLE GEAR SHAFT | *2 | NO. 2 IDLE GEAR SHAFT |
| *3 | OIL PUMP DRIVE SHAFT SPROCKET | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | OIL PUMP DRIVE SPROCKET | *6 | CHAIN TENSIONER PLATE |
| *7 | CHAIN DAMPER SPRING | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *1 | TIMING CHAIN COVER PLATE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
MP grease |
| ★ | Precoated part |
|
Do not apply lubricants to the threads |
| *T1 | 1st: 120 (1224, 89) 2nd: 365 (3722, 269) |
- | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 69 | SPARK PLUG TUBE GASKET LH | 11193A | - | - | - |
| 70 | CYLINDER HEAD COVER SUB-ASSEMBLY LH | 11202 | ( ) |
- | - |
| 71 | SPARK PLUG | 19100P | ( ) |
- | - |
| *1 | CAMSHAFT POSITION SENSOR (for Intake Side of Bank 2) | *2 | CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 2) |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 72 | SPARK PLUG TUBE GASKET RH | 11193B | - | - | - |
| 73 | CYLINDER HEAD COVER SUB-ASSEMBLY RH | 11201M | ( ) |
- | - |
| 74 | SPARK PLUG | 19100P | ( ) |
- | - |
| *1 | CAMSHAFT POSITION SENSOR (for Intake Side of Bank 1) | *2 | CAMSHAFT POSITION SENSOR (for Exhaust Side of Bank 1) |
| *3 | NO. 1 INTERCOOLER AIR GUIDE | *4 | OIL FILLER CAP ASSEMBLY |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with union nut wrench | ● | Non-reusable part |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
11151 1.INSTALL RING PIN
| *A | for Bank 1 | *B | for Bank 2 |
| *a | Protrusion Height | - | - |
Using a plastic-faced hammer, tap in new ring pins to the camshaft housing sub-assembly.
2.7 to 3.3 mm (0.106 to 0.130 in.)
12211 2.INSTALL NO. 1 PCV CASE (NO. 1 VENTILATION CASE)
Install a new gasket to the No. 1 PCV case (No. 1 PCV case).
Check that the gasket is securely fitted into the installation groove.
Install the No. 1 PCV case (No. 1 PCV case) with the 9 bolts in the order shown in the illustration.
82219C 5.INSTALL SENSOR WIRE
13560A 15.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
13550 25.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
11381A 30.INSTALL REAR ENGINE OIL SEAL
| *1 | Rear Engine Oil Seal Retainer | - | - |
| *a | 0 to 0.5 mm (0 to 0.0197 in.) | - | - |
Place the rear engine oil seal retainer on wooden blocks.
Using SST, tap in a new rear engine oil seal until its surface is flush with the rear engine oil seal retainer edge.
0 to 0.5 mm (0 to 0.0197 in.)
Keep the lip free of foreign matter.
Do not tap on the rear engine oil seal at an angle.
11381 31.INSTALL REAR ENGINE OIL SEAL RETAINER
| *a | Standard Seal Packing Diameter 2.5 to 3.5 mm (0.0984 to 0.138 in.) |
*b | Wide Seal Packing Diameter 4.5 to 5.5 mm (0.177 to 0.217 in.) |
| *c | Seal Packing Width 88 mm (1.10 in.) | - | - |
|
Bolt A (Do not reuse) |
|
Bolt B |
|
Seal Packing | - | - |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Do not start the engine for at least 2 hours after installation.
Install the rear engine oil seal retainer with 6 new bolts and the 4 bolts.
12121 32.INSTALL NO. 1 OIL PAN BAFFLE PLATE
Temporarily install the No. 1 oil pan baffle plate with the 4 bolts.
After temporarily installing the 4 bolts, install the oil strainer sub-assembly.
15104 33.INSTALL OIL STRAINER SUB-ASSEMBLY
Install a new gasket with the oil strainer sub-assembly.
Check that the gasket is securely fitted into the installation groove.
Temporarily install the oil strainer sub-assembly to the crankshaft bearing cap sub-assembly with the 3 bolts.
Tighten the 7 bolts in the order shown in the illustration.
12101R 34.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
| *a | Standard Seal Packing Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.) |
*b | Wide Seal Packing Diameter 5.5 to 6.5 mm (0.216 to 0.255 in.) |
| *c | Thick Coating Cross-section | *d | Seal Packing Width 38 mm (1.49 in.) |
| *e | Seal Packing Width 60 mm (2.36 in.) | *f | 3.0 mm (0.118 in.) or more |
| *g | 8.0 to 12 mm (0.315 to 0.472 in.) | - | - |
|
Bolt A |
|
Bolt B |
|
Bolt C | - | - |
Remove any remaining seal packing material and be careful not to drop any oil on the contact surfaces of the No. 1 oil pan sub-assembly and crankshaft bearing cap sub-assembly.
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the No. 1 oil pan sub-assembly within 3 minutes after applying seal packing.
Install the No. 1 oil pan sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| Bolt A | 30 mm (1.18 in.) |
| Bolt B | 92 mm (3.62 in.) |
| Bolt C | 50 mm (1.97 in.) |
12102A 36.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
| *A | Type A | *B | Type B |
| *a | 3.0 to 4.0 mm (0.118 to 0.157 in.) | - | - |
|
Bolt |
|
Nut |
|
Seal Packing | - | - |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
Remove any oil from the contact surface.
Install the No. 2 oil pan sub-assembly within 3 minutes after applying seal packing.
Install the No. 2 oil pan sub-assembly with the 9 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.
Tighten the nuts first. After tightening the bolts, check that the nuts and bolts are tightened to the specified torque.
Do not start the engine for at least 2 hours after the installation.
12101A 37.INSTALL OIL PAN DRAIN PLUG
Install a new gasket to the oil pan drain plug.
Install the oil pan drain plug.
12144 38.INSTALL OIL PAN COVER SILENCER
12616 39.INSTALL NO. 6 ENGINE COVER
11310 40.INSTALL TIMING CHAIN COVER ASSEMBLY
|
|
| *a | 3.0 to 4.0 mm (0.118 to 0.157 in.) | - | - |
|
Seal Packing | - | - |
Cylinder Block Sub-assembly Side:
Install 3 new oil pump gaskets to the cylinder block sub-assembly.
Timing Chain Cover Assembly Side:
Install 2 new oil pump gaskets and 2 new water pump gaskets to the timing chain cover assembly.
Apply seal packing in a continuous line to the engine unit as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Temporarily install the timing chain cover assembly with the 27 bolts.
Make sure that there is no oil on the bolt threads.
Tighten the bolts in the order shown in the illustration.
Do not start the engine for at least 2 hours after installation.
Wipe off any seal packing that seeped out around the surfaces of the No. 1 oil pan sub-assembly and cylinder head cover sub-assembly and make sure that there is no seal packing seeping out around the edges.
13521 41.INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET
13562 42.INSTALL NO. 2 CHAIN VIBRATION DAMPER
13561 43.INSTALL NO. 1 CHAIN VIBRATION DAMPER
13530 44.INSTALL IDLE SPROCKET ASSEMBLY
| *1 | No. 1 Idle Gear Shaft | *2 | Idle Sprocket Assembly |
| *3 | No. 2 Idle Gear Shaft | - | - |
| *a | Knock Pin | - | - |
|
Apply Engine Oil | - | - |
Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.
Temporarily install the No. 1 idle gear shaft and idle sprocket assembly with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear with the knock pin groove of the cylinder block sub-assembly.
Make sure that the idle gear is facing the correct direction.
Check that no foreign objects are on the No. 1 and No. 2 idle gear shafts.
Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.
After installing the idle sprocket assembly, check that the idle sprocket turns smoothly.
13506A 45.INSTALL NO. 1 CHAIN SUB-ASSEMBLY
| *A | for Bank 1 | *B | for Bank 2 |
| *1 | Crankshaft Pulley Set Key | - | - |
| *a | 60° | *b | Timing Mark |
Turn the crankshaft 60° counterclockwise and set it as shown in the illustration.
Check that the camshaft timing gear position on the bank 1 is as shown in the illustration.
Check that the camshaft timing gear position on the bank 2 is as shown in the illustration.
| *a | Mark Plate (Pink) | *b | Timing Mark |
Align the mark plates and timing marks as shown in the illustration and install the No. 1 chain sub-assembly.
The camshaft mark plates are pink.
| *a | When idle sprocket is reused | *b | Mark |
| *c | Align | *d | Chain Plate |
| *e | Chain sub-assembly between the banks | - | - |
|
Turn | - | - |
Rest the No. 1 chain sub-assembly on top of the crankshaft.
Turn the camshaft timing gear assembly on the RH bank counterclockwise to tighten the chain sub-assembly between the banks.
When the idle sprocket is reused, align the chain plate with the mark where the plate had been in order to tighten the chain sub-assembly between the banks.
| *1 | Crankshaft Pulley Set Key | - | - |
| *a | Mark Plate (Orange) | *b | Timing Mark |
| *c | Center Line | - | - |
Align the mark plate and timing mark as shown in the illustration and install the No. 1 chain sub-assembly onto the crankshaft timing sprocket.
The crankshaft mark plate is orange.
Temporarily install the crankshaft pulley set bolt.
Turn the crankshaft clockwise to set it to the block bore center line RH (TDC/compression).
13559 46.INSTALL CHAIN TENSIONER SLIPPER
13540 47.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Stopper Plate | *b | Plunger |
| *c | Pin | - | - |
Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.
Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.0500 in.) diameter into the hole of the stopper plate.
Install a new gasket to the No. 1 chain tensioner assembly.
Install the No. 1 chain tensioner assembly with the 2 bolts.
Remove the lock pin of the No. 1 chain tensioner assembly.
48.INSPECT VALVE TIMING
| *a | Timing Mark (Camshaft Timing Intake Gear Assembly Side) | *b | Timing Mark (Camshaft Timing Exhaust Gear Assembly Side) |
for Bank 1 Side:
Check that each camshaft timing mark is positioned as shown in the illustration.
Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
| *a | Timing Mark (Camshaft Timing Intake Gear Assembly Side) | *b | Timing Mark (Camshaft Timing Exhaust Gear Assembly Side) |
for Bank 2 Side:
Check that each camshaft timing mark is positioned as shown in the illustration.
Check each timing mark from a viewpoint directly inline with the center of the camshaft and the timing mark on each camshaft timing gear.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
If the valve timing is misaligned, reinstall the timing chain.
Remove the crankshaft pulley set bolt.
15370E 53.INSTALL CAM TIMING OIL CONTROL SOLENOID LH O-RING (for Exhaust Side of Bank 2)
15370C 54.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY LH (for Exhaust Side of Bank 2)
15370E 55.INSTALL CAM TIMING OIL CONTROL SOLENOID LH O-RING (for Intake Side of Bank 2)
15370C 56.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY LH (for Intake Side of Bank 2)
15370D 57.INSTALL CAM TIMING OIL CONTROL SOLENOID RH O-RING (for Exhaust Side of Bank 1)
15370B 58.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Exhaust Side of Bank 1)
15370D 59.INSTALL CAM TIMING OIL CONTROL SOLENOID RH O-RING (for Intake Side of Bank 1)
15370B 60.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY RH (for Intake Side of Bank 1)
15710B 61.INSTALL OIL COOLER O-RING
15785 62.INSTALL OIL COOLER GASKET
15710 63.INSTALL OIL COOLER ASSEMBLY
15601 64.INSTALL OIL FILTER SUB-ASSEMBLY
11193A 69.INSTALL SPARK PLUG TUBE GASKET LH
11193B 72.INSTALL SPARK PLUG TUBE GASKET RH
23695A 82.INSTALL NOZZLE HOLDER CLAMP
82126A 83.INSTALL NO. 6 ENGINE WIRE
23695A 93.INSTALL NOZZLE HOLDER CLAMP
82125N 94.INSTALL NO. 5 ENGINE WIRE
16268 103.INSTALL NO. 1 WATER BY-PASS PIPE
17273 104.INSTALL NO. 1 TURBO INSULATOR STAY
12614A 105.INSTALL NO. 4 ENGINE COVER
12615A 107.INSTALL NO. 5 ENGINE COVER