Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER HEAD GASKET (w/ DPF) › from 2016.08
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0290064 CYLINDER HEAD GASKET(w/ DPF) A

1VD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET(w/ DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Before performing these installation procedures, sufficiently clean and remove any foreign matter from the cylinder block, cylinder head, camshaft and other parts.

·

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.

·

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM (w/ DPF)>ON-VEHICLE INSPECTION).



PROCEDURE

Hide 11115 1.SELECT NO. 1 CYLINDER HEAD GASKET

a.

Set the 2 crankshaft pulley set bolts to the crankshaft.


b.

Clean the cylinder block sub-assembly with solvent.


c.

Inspect the protrusions for each cylinder.

i.

Set the piston of the cylinder to be measured to slightly before TDC.


ii.
A164862

Place a dial indicator on the cylinder block sub-assembly, and set the measuring tip as shown in the illustration.

NOTICE:

Make sure that the dial indicator is at a right angle to the cylinder block sub-assembly top surface.



iii.

Set the dial indicator at 0 mm (0 in.).

HINT:

Make sure that the measuring tip is flat against the cylinder block sub-assembly surface and piston head when taking the measurements.



iv.

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.


v.

Measure the piston protrusion value of each cylinder at 2 places as shown in the illustration below, making a total of 8 measurements.

Standard piston protrusion:

0.520 to 0.780 mm (0.0205 to 0.0307 in.)


If the protrusion is not as specified, remove and reinstall the piston and connecting rod.

A164863C01
0.635,2.427 0.948,2.583 0.313,0.156 10 false *a
*a Measuring Point
V100136

Front




d.
A326393C01
2.781,0.354 2.938,0.552 0.156,0.198 10 false A 2.781,0.708 2.938,0.906 0.156,0.198 10 false B 2.771,1.052 2.927,1.25 0.156,0.198 10 false C 2.771,1.406 2.927,1.604 0.156,0.198 10 false D 2.771,1.75 2.927,1.948 0.156,0.198 10 false E
V100136

Front


Select a new No. 1 cylinder head gasket.

HINT:

No. 1 cylinder head gaskets are marked A, B, C, D or E accordingly.


New Installed No. 1 Cylinder Head Gasket Thickness:
Item Cutout Specified Condition (*)
A 1 1.20 to 1.30 mm (0.0472 to 0.0512 in.)
B 2 1.25 to 1.35 mm (0.0492 to 0.0532 in.)
C 3 1.30 to 1.40 mm (0.0512 to 0.0551 in.)
D 4 1.35 to 1.45 mm (0.0532 to 0.0571 in.)
E 5 1.40 to 1.50 mm (0.0551 to 0.0591 in.)


HINT:

*: The specified condition indicates the thickness of the No. 1 cylinder head gasket after tightening the cylinder head sub-assembly RH.


i.

Select the largest piston protrusion value from the measurements and then select a new appropriate No. 1 cylinder head gasket according to the table below.

Standard Piston Protrusion:
Item Specified Condition
A 0.520 to 0.575 mm (0.0205 to 0.0226 in.)
B 0.575 to 0.625 mm (0.0226 to 0.0246 in.)
C 0.625 to 0.675 mm (0.0246 to 0.0266 in.)
D 0.675 to 0.725 mm (0.0266 to 0.0285 in.)
E 0.725 to 0.780 mm (0.0285 to 0.0307 in.)




e.

Remove the 2 crankshaft pulley set bolts.


Hide 11116 2.SELECT NO. 2 CYLINDER HEAD GASKET

a.

Set the 2 crankshaft pulley set bolts to the crankshaft.


b.

Clean the cylinder block sub-assembly with solvent.


c.

Inspect the protrusions for each cylinder.

i.
A164862

Set the piston of the cylinder to be measured to slightly before TDC.


ii.

Place a dial indicator on the cylinder block sub-assembly, and set the measuring tip as shown in the illustration.

NOTICE:

Make sure that the dial indicator is at a right angle to the cylinder block sub-assembly top surface.



iii.

Set the dial indicator at 0 mm (0 in.).

HINT:

Make sure that the measuring tip is flat against the cylinder block sub-assembly surface and piston head when taking the measurements.



iv.

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.


v.

Measure the piston protrusion value of each cylinder at 2 places as shown in the illustration below, making a total of 8 measurements.

Standard piston protrusion:

0.520 to 0.780 mm (0.0205 to 0.0307 in.)


If the protrusion is not as specified, remove and reinstall the piston and connecting rod.

A164894C01
0.521,2.396 0.833,2.552 0.313,0.156 10 false *a
*a Measuring Point
V100136

Front




d.
A326394C01
2.76,2.75 2.917,2.948 0.156,0.198 10 false A 2.771,3.094 2.927,3.292 0.156,0.198 10 false B 2.76,3.438 2.917,3.635 0.156,0.198 10 false C 2.76,3.792 2.917,3.99 0.156,0.198 10 false D 2.76,4.146 2.917,4.344 0.156,0.198 10 false E
V100136

Front


Select a new No. 2 cylinder head gasket.

HINT:

No. 2 cylinder head gaskets are marked A, B, C, D or E accordingly.


New Installed No. 2 Cylinder Head Gasket Thickness:
Item Cutout Specified Condition (*)
A 1 1.20 to 1.30 mm (0.0472 to 0.0512 in.)
B 2 1.25 to 1.35 mm (0.0492 to 0.0532 in.)
C 3 1.30 to 1.40 mm (0.0512 to 0.0551 in.)
D 4 1.35 to 1.45 mm (0.0532 to 0.0571 in.)
E 5 1.40 to 1.50 mm (0.0551 to 0.0591 in.)


HINT:

*: The specified condition indicates the thickness of the No. 2 cylinder head gasket after tightening the cylinder head sub-assembly LH.


i.

Select the largest piston protrusion value from the measurements and then select a new appropriate No. 2 cylinder head gasket according to the table below.

Standard Piston Protrusion:
Item Specified Condition
A 0.520 to 0.575 mm (0.0205 to 0.0226 in.)
B 0.575 to 0.625 mm (0.0226 to 0.0246 in.)
C 0.625 to 0.675 mm (0.0246 to 0.0266 in.)
D 0.675 to 0.725 mm (0.0266 to 0.0285 in.)
E 0.725 to 0.780 mm (0.0285 to 0.0307 in.)




e.

Remove the 2 crankshaft pulley set bolts.


Hide 11115 3.INSTALL NO. 1 CYLINDER HEAD GASKET

a.

Remove any oil from the contact surface.


b.
A164879C01
1.427,1.167 1.74,1.323 0.313,0.156 10 false *a 2.031,0.552 2.344,0.708 0.313,0.156 10 false *b
*a Front
*b Exhaust Side


Place the No. 1 cylinder head gasket on the cylinder block sub-assembly surface with the front face of the indicated mark "R" upward and facing the exhaust side.


Hide 11116 4.INSTALL NO. 2 CYLINDER HEAD GASKET

a.

Remove any oil from the contact surface.


b.
A164880C01
1.552,2 1.865,2.156 0.313,0.156 10 false *a 2.167,2.563 2.479,2.719 0.313,0.156 10 false *b
*a Front
*b Exhaust Side


Place the No. 2 cylinder head gasket on the cylinder block sub-assembly surface with the front face of the indicated mark "L" upward and facing the exhaust side.


Hide 11101 5.INSTALL CYLINDER HEAD SUB-ASSEMBLY RH

a.

Place the cylinder head sub-assembly RH on the No. 1 cylinder head gasket.

NOTICE:

Ensure that no oil is on the mounting surface of the cylinder head sub-assembly RH.



b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


c.

Step 1:

i.
A164533N02
0.292,0.854 0.51,1.01 0.219,0.156 10 true 10 0.927,0.865 1.24,1.063 0.313,0.198 10 false 6 1.531,0.865 1.844,1.063 0.313,0.198 10 false 2 2.125,0.854 2.344,1 0.219,0.146 10 true 3 2.75,0.865 3.052,1.021 0.302,0.156 10 true 7 2.771,2.594 3.083,2.792 0.313,0.198 10 false 8 2.156,2.594 2.469,2.792 0.313,0.198 10 false 4 1.542,2.615 1.854,2.813 0.313,0.198 10 false 1 0.938,2.594 1.25,2.792 0.313,0.198 10 false 5 0.344,2.594 0.656,2.792 0.313,0.198 10 false 9

Install and uniformly tighten the 10 cylinder head set bolts with the spacers in several steps, in the sequence shown in the illustration.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

The cylinder head set bolts are tightened in 4 progressive steps.

·

If a cylinder head set bolt is broken or deformed, replace it.





d.

Step 2:

i.
A158686C05
1.083,1.917 1.083,1.75 1.083,1.75 1.51,1.135 true 1.01,1.896 1.323,2.052 0.313,0.156 10 false *a 1.177,0.417 1.635,0.615 0.458,0.198 10 false 90°
*a Painted Mark
V100136

Front


Mark the cylinder head set bolt heads with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts another 90° in the sequence shown in step 1.



e.

Step 3:

i.
A158687C02
1.167,0.25 1.333,0.25 1.333,0.25 1.875,0.594 true 1.01,0.146 1.323,0.302 0.313,0.156 10 false *a 2.583,0.354 3.042,0.552 0.458,0.198 10 false 90°
*a Painted Mark
V100136

Front


Tighten the cylinder head set bolts by an additional 90° in the sequence shown in step 1.



f.

Step 4:

i.
A164864C02
2.594,0.948 2.917,0.333 2.917,0.333 3.083,0.333 true 3.104,0.24 3.417,0.396 0.313,0.156 10 false *a 2.792,1.521 3.25,1.719 0.458,0.198 10 false 90°
*a Painted Mark
V100136

Front


Tighten the cylinder head set bolts by an additional 90° in the sequence shown in step 1.


ii.

Check that the painted marks are now facing the LH side.



Hide 11102 6.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

a.

Place the cylinder head sub-assembly LH on the No. 2 cylinder head gasket.

NOTICE:

Ensure that no oil is on the mounting surface of the cylinder head sub-assembly LH.



b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


c.

Step 1:

i.
A164541N02
0.51,0.75 0.688,0.917 0.177,0.167 10 true 8 1.125,0.75 1.281,0.906 0.156,0.156 10 true 4 1.729,0.76 1.969,0.927 0.24,0.167 10 true 1 2.323,0.781 2.51,0.927 0.188,0.146 10 true 5 2.906,0.781 3.083,0.948 0.177,0.167 10 false 9 2.948,2.51 3.198,2.698 0.25,0.188 10 true 10 2.375,2.51 2.688,2.708 0.313,0.198 10 true 6 1.74,2.51 2.052,2.708 0.313,0.198 10 true 2 1.115,2.51 1.427,2.708 0.313,0.198 10 true 3 0.49,2.5 0.802,2.698 0.313,0.198 10 false 7

Install and uniformly tighten the 10 cylinder head set bolts with the spacers in several steps, in the sequence shown in the illustration.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

The cylinder head set bolts are tightened in 4 progressive steps.

·

If a cylinder head set bolt is broken or deformed, replace it.





d.

Step 2:

i.
A158686C05
1.083,1.917 1.083,1.75 1.083,1.75 1.51,1.135 true 1.01,1.896 1.323,2.052 0.313,0.156 10 false *a 1.177,0.417 1.635,0.615 0.458,0.198 10 false 90°
*a Painted Mark
V100136

Front


Mark the cylinder head set bolt heads with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts 90° in the sequence shown in step 1.



e.

Step 3:

i.
A158687C02
1.167,0.25 1.333,0.25 1.333,0.25 1.875,0.594 true 1.01,0.146 1.323,0.302 0.313,0.156 10 false *a 2.583,0.354 3.042,0.552 0.458,0.198 10 false 90°
*a Painted Mark
V100136

Front


Tighten the cylinder head set bolts another 90° in the sequence shown in step 1.



f.

Step 4:

i.
A164864C02
2.594,0.948 2.917,0.333 2.917,0.333 3.083,0.333 true 3.104,0.24 3.417,0.396 0.313,0.156 10 false *a 2.792,1.521 3.25,1.719 0.458,0.198 10 false 90°
*a Painted Mark
V100136

Front


Tighten the cylinder head set bolts by an additional 90° in the sequence shown in step 1.


ii.

Check that the painted marks are now facing the LH side.



Hide 13750 7.INSTALL NO. 1 VALVE LASH ADJUSTER ASSEMBLY

Hide 8.INSTALL NO. 2 VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 9.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 10.INSTALL NO. 2 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11.INSTALL NO. 2 CAMSHAFT BEARING CAP

Hide 12.INSTALL NO. 5 CAMSHAFT BEARING CAP

Hide 13.SET NO. 1 CYLINDER TO 45° BEFORE TDC

Hide 13511 14.INSTALL NO. 1 AND NO. 2 CAMSHAFTS

Hide 13053 15.INSTALL NO. 3 AND NO. 4 CAMSHAFTS

Hide 11301 16.INSTALL TIMING GEAR CASE SUB-ASSEMBLY

Hide 22100 18.INSTALL FUEL SUPPLY PUMP ASSEMBLY

Hide 13613 21.TEMPORARILY INSTALL INJECTION PUMP DRIVE GEAR

Hide 22.SET NO. 1 AND NO. 2 CAMSHAFTS TO TDC/COMPRESSION

Hide 13581 23.INSTALL NO. 1 IDLE GEAR SHAFT

Hide 25.TIGHTEN INJECTION PUMP DRIVE GEAR NUT

Hide 26.CHECK NO. 1 CYLINDER AT TDC/COMPRESSION

Hide 13529G 27.INSTALL NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 CHAIN SUB-ASSEMBLY

Hide 13523 28.INSTALL NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 CHAIN SUB-ASSEMBLY

Hide 13522 29.INSTALL PUMP DRIVE SHAFT GEAR

Hide 30.INSTALL NO. 2 CHAIN VIBRATION DAMPER

Hide 31.INSTALL NO. 2 CHAIN TENSIONER SLIPPER

Hide 32.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13561 33.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13559 34.INSTALL NO. 1 CHAIN TENSIONER SLIPPER

Hide 13540 35.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 19315 36.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 37.CHECK NO. 1 CYLINDER AT TDC/COMPRESSION

Hide 11302A 38.INSTALL FRONT CRANKSHAFT OIL SEAL

Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 23710B 41.INSTALL EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

Hide 17111 42.TEMPORARILY INSTALL INTAKE MANIFOLD

Hide 17112 43.TEMPORARILY INSTALL NO. 2 INTAKE MANIFOLD

Hide 17114D 44.TEMPORARILY INSTALL NO. 3 INTAKE MANIFOLD

Hide 11202 45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11201 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 47.INSTALL FUEL INJECTOR ASSEMBLY LH

Hide 23670 48.INSTALL FUEL INJECTOR ASSEMBLY RH

Hide 17114D 49.REMOVE NO. 3 INTAKE MANIFOLD

Hide 17112 50.REMOVE NO. 2 INTAKE MANIFOLD

Hide 12101 54.INSTALL OIL PAN SUB-ASSEMBLY

Hide 15620 55.INSTALL OIL FILTER CAP ASSEMBLY WITH ELEMENT

Hide 15614 56.INSTALL LOWER OIL FILTER ELEMENT COVER

Hide 12102A 57.CHECK NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12102A 58.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 11452 60.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 11459 61.INSTALL ENGINE OIL LEVEL LEVEL DIPSTICK GUIDE SUPPORT

Hide 12142 62.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15301 63.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 64.CONNECT VACUUM HOSE

Hide 17293 65.INSTALL TURBOCHARGER STAY

Hide 12201 66.INSTALL VENTILATION TUBE SUB-ASSEMBLY

Hide 12263 67.CONNECT NO. 3 VENTILATION HOSE

Hide 25708 68.CONNECT NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

Hide 15474A 69.INSTALL TURBO OIL OUTLET HOSE

Hide 83520 71.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY (w/ Oil Pressure Gauge)

Hide 83530 72.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY (w/o Oil Pressure Gauge)

Hide 15407 73.CONNECT TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 15769 74.CONNECT OIL COOLER PIPE

Hide 17878 75.INSTALL NO. 3 INTAKE AIR CONNECTOR PIPE

Hide 17142 77.INSTALL EXHAUST MANIFOLD LH WITH TURBOCHARGER SUB-ASSEMBLY

Hide 16630H 84.INSTALL IDLER PULLEY ASSEMBLY (w/o Air Conditioning System)

Hide 88320 85.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 29300 87.INSTALL VACUUM PUMP ASSEMBLY

Hide 16100 88.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 15778 89.CONNECT NO. 2 OIL COOLER HOSE

Hide 12502 93.INSTALL CHAIN COVER AND COMPRESSOR BRACKET SUB-ASSEMBLY

Hide 16620D 97.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16603B 98.INSTALL IDLER PULLEY SUB-ASSEMBLY

Hide 27280 100.INSTALL GENERATOR SPLASH GUARD COVER ASSEMBLY

Hide 16307A 101.INSTALL FAN BRACKET SUB-ASSEMBLY

Hide 17945 105.INSTALL INTERCOOLER SUPPORT BRACKET

Hide 19850 106.INSTALL GLOW PLUG ASSEMBLY

Hide 17946 107.INSTALL NO. 2 INTERCOOLER SUPPORT BRACKET

Hide 28100 108.INSTALL STARTER ASSEMBLY

Hide 109.INSTALL STARTER HOSE BRACKET SUB-ASSEMBLY