PROBLEM SYMPTOMS TABLE
Troubleshooting · Vehicles built from Nov 2005
- HINT:
- When a malfunction cannot be confirmed by conducting a DTC check and the cause of the problem cannot be identified through a basic inspection, troubleshoot in accordance with the priority order indicated in the table below.
- Inspect the fuse and relay before confirming the suspected areas as shown in the chart below.
- When a malfunction cannot be confirmed by conducting a DTC check and the cause of the problem cannot be identified through a basic inspection, troubleshoot in accordance with the priority order indicated in the table below.
- NOTICE:
- When removing the following parts, perform the operations correctly by following the precautions on the relevant pages.
| Symptom |
Suspected area |
See page |
| No up-shift, No down-shift |
1. Transmission unit (Gears, bearings, shift fork, synchronizer ring, shift key, etc.) |
Click here
|
| 2. Clutch disk (Clutch cover) |
Click here
|
|
| 3. Clutch stroke sensor |
Click here
|
|
| 4. Clutch actuator assembly |
Click here
|
|
| 5. Shift stroke sensor |
Click here
|
|
| 6. Select stroke sensor |
Click here
|
|
| 7. Shift and select actuator |
Click here
|
|
| 8. Shift lever position sensor |
Click here
|
|
| 9. Shift lever assembly |
Click here
|
|
| 10. Speed signal circuit |
Click here
|
|
| 11. Transmission control ECU |
Click here
|
|
| Multi-mode manual transmission warning light defective |
1. Multi-mode manual transmission warning light circuit |
Click here
|
| 2. IG signal circuit |
Click here
|
|
| 3. ECU power source circuit |
Click here
|
|
| 4. Transmission control ECU |
Click here
|
|
| Shift position indicator light defective |
1. Multi-mode manual transmission warning light circuit |
Click here
|
| 2. IG signal circuit |
Click here
|
|
| 3. Transmission control ECU |
Click here
|
|
| Buzzer does not sound when incorrect operation occurs (built into transmission control ECU) |
1. Transmission control ECU |
Click here
|
| Buzzer does not sound when incorrect operation occurs (built into combination meter) |
1. Multi-mode manual transmission warning light circuit |
Click here
|
| 2. IG signal circuit |
Click here
|
|
| 3. Front door courtesy switch |
Click here
|
|
| 4. Combination meter |
Click here
|
|
| 5. Transmission control ECU |
Click here
|
|
| Shift impossible to any gear |
1. Transmission unit (Gears, bearings, shift fork, synchronizer ring, shift key, etc.) |
Click here
|
| 2. Shift stroke sensor |
Click here
|
|
| 3. Select stroke sensor |
Click here
|
|
| 4. Shift and select actuator |
Click here
|
|
| 5. Shift lever position sensor |
Click here
|
|
| 6. Clutch disk (clutch cover) |
Click here
|
|
| 7. Clutch stroke sensor |
Click here
|
|
| 8. Clutch actuator assembly |
Click here
|
|
| 9. Transmission control ECU |
Click here
|
|
| Too much time lag when changing gear position |
1. Transmission unit (Gears, bearings, shift fork, synchronizer ring, shift key, etc.) |
Click here
|
| 2. Clutch disc (Clutch cover) |
Click here
|
|
| 3. Clutch stroke sensor |
Click here
|
|
| 4. Clutch actuator assembly |
Click here
|
|
| 5. Shift stroke sensor |
Click here
|
|
| 6. Select stroke sensor |
Click here
|
|
| 7. Shift and select actuator |
Click here
|
|
| 8. Shift lever position sensor |
Click here
|
|
| 9. Shift lock solenoid circuit |
Click here
|
|
| 10. Shift lever assembly |
Click here
|
|
| 11. Speed signal circuit |
Click here
|
|
| 12. Transmission control ECU |
Click here
|
|
| Poor acceleration |
1. SFI system (1KR-FE) |
Click here
|
| 2. SFI system (2SZ-FE) |
Click here
|
|
| 3. Pattern select switch |
Click here
|
|
| 4. Transmission control ECU |
Click here
|
|
| Change shift lever position impossible |
1. Shift lock solenoid circuit |
Click here
|
| 2. Stop light switch circuit |
Click here
|
|
| 3. IG signal circuit |
Click here
|
|
| 4. Shift lever assembly |
Click here
|
|
| 5. Transmission control ECU |
Click here
|
|
| Engine stalls when starting off or stopping |
1. Transmission revolution sensor |
Click here
|
| 2. Transmission control ECU |
Click here
|
|
| Gear not automatically shifted up or down during E mode driving |
1. CAN communication circuit |
Click here
|
| 2. Transmission shift main switch |
Click here
|
|
| 3. Shift lever position sensor |
Click here
|
|
| 4. Transmission control ECU |
Click here
|
|
| Mode switch impossible (E to M) |
1. Transmission shift main switch |
Click here
|
| 2. Shift lever assembly |
Click here
|
|
| 3. Transmission control ECU |
Click here
|
|
| Setting to 1st or R positions impossible |
1. Shift lever position sensor |
Click here
|
| 2. Transmission control ECU |
Click here
|
|
| Shift timing delays occur during M mode driving |
1. Accelerator pedal position sensor (1KR-FE) |
Click here
|
| 2. Accelerator pedal position sensor (2SZ-FE) |
Click here
|
|
| 3. Transmission control ECU |
Click here
|
|
| Assist control does not operate when engine started |
1. Parking brake switch circuit |
Click here
|
| 2. Transmission control ECU |
Click here
|
|
| Engine does not crank |
1. SFI system (1KR-FE) |
Click here
|
| 2. SFI system (2SZ-FE) |
Click here
|
|
| 3. Starter signal circuit |
Click here
|
|
| 4. Stop light switch circuit |
Click here
|
|
| 5. Shift lever position sensor |
Click here
|
|
| 6. Starter (for 1KR-FE 0.9 kW) |
Click here
|
|
| 7. Starter (for 1KR-FE 1.3 kW) |
Click here
|
|
| 8. Starter (for 2SZ-FE) |
Click here
|
|
| 10. Transmission control ECU |
Click here
|
|
| Noise |
1. Oil (level low) |
Click here
|
| 2. Oil (Wrong) |
Click here
|
|
| 3. Gear (Worn or damaged) |
Click here
|
|
| 4. Bearing (Worn or damaged) |
Click here
|
|
| Oil leakage |
1. Oil (Level too high) |
Click here
|
| 2. Gasket (Damaged) |
Click here
|
|
| 3. Oil seal (Worn or damaged) |
Click here
|
|
| 4. O-ring (Worn or damaged) |
Click here
|