Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P1604    Startability Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the engine does not start even though the starter signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.
Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No.
DTC Detection Condition
Trouble Area
P1604
One of the following conditions is met (1 trip detection logic):
  1. The engine speed is less than 500 rpm with the starter signal on for a certain amount of time (Depending on the engine coolant temperature and atmospheric pressure).
  2. After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 300 rpm or less immediately.
  1. Engine immobiliser system
  2. Engine assembly (excess friction, compression loss)
  3. Starter assembly
  4. Crankshaft position sensor
  5. VVT sensor
  6. Engine coolant temperature sensor
  7. Fuel pump assembly
  8. Fuel pump control circuit (low pressure side)
  9. Fuel pipes
  10. Fuel injector assembly (for port injection)
  11. Throttle with motor body assembly
  12. Pressure regulator
  13. Battery
  14. Flywheel (for Manual Transmission)
  15. Drive plate (for Automatic Transmission)
  16. Spark plug
  17. Ignition coil circuit
  18. Intake system
  19. Camshaft timing oil control valve
  20. Mass air flow meter
  21. Air fuel ratio sensor
  22. Valve timing
  23. Fuel
  24. Purge valve
  25. Intake valve
  26. Exhaust valve
  27. ECM

INSPECTION PROCEDURE

HINT:
  1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
    As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
  2. If any other DTCs are output, perform troubleshooting for those DTCs first.
  3. When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
  4. Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  5. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
  6. When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
  7. Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
  8. If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
  9. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
  10. If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.


Malfunction Recurrence and Inspection Areas
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    1. The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

      HINT:
      One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.

      1. If the battery voltage is less than 9 V during cranking, there is a high probability that engine friction is abnormal.
      2. If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

      3. If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or ECM may be malfunctioning.


        A215383E01

    2. All engine speeds recorded in the freeze frame data are between 100 and 250 rpm (the engine cranks but there is no combustion).

      HINT:
      If the engine speed is between 100 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.


        A215384E34

    3. The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

      HINT:
      If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.

      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
      2. If Long FT is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

      3. If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.


        A215383E02

  2. When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem Symptoms" and "Systems to Inspect").

    1. Problem Symptoms

      1. The engine does not crank.

        HINT:
        The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.

      2. The engine cranking speed is abnormal.

        HINT:
        If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.

      3. There is no initial combustion.

        HINT:
        If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.

      4. The engine stalls after starter turnoff.

        HINT:
        If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.

      5. The initial combustion and starter turnoff occur late.

        HINT:
        If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).

        HINT:
        Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
        1. When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
        2. When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
        3. When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.

    2. Systems to Inspect

      1. Intake system
      2. Ignition system
      3. Fuel system


INSPECTION FLOW
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    Freeze Frame Data Item
    Result
    Suspected Area
    Procedure
    Engine Speed
    0 rpm (no engine cranking at all)
    1. Battery fully depleted
    2. Engine assembly (excess friction)
    3. Starter assembly
    4. Engine immobiliser system
    5. Crankshaft position sensor
    6. ECM
    4 to 9
    100 to 250 rpm (engine cranks but no initial combustion*1)
    1. Fuel pump control circuit (Low pressure side)
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Fuel injection system
    10 to 14
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
    1. Engine assembly (compression loss)
    2. Fuel injection system
    3. Fuel pump control circuit (low pressure side)
    15 to 23

    HINT:
    1. *1: First combustion after cranking begins.
    2. *2: Condition when engine speed increases and starter can be turned off.

  2. When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

    1. Problem Symptoms

      Problem Symptom
      Suspected Area
      Suspected Component
      Procedure
      The engine does not crank
      Battery malfunction
      1. Battery fully depleted
      26 to 31
      Starting system
      1. Starter assembly (includes pinion gear wear or tooth damage)
      2. Starting system
      Engine immobiliser system
      1. Engine immobiliser system
      Engine assembly
      1. Engine assembly (excess friction)
      2. Drive plate wear or tooth damage
      Cranking speed too low
      Battery malfunction
      1. Battery fully depleted
      32 to 34
      Starting system
      1. Starter assembly
      Engine assembly
      1. Engine assembly (excess friction)
      Cranking speed too high
      Engine assembly
      1. Engine assembly (compression loss)
      There is no initial combustion
      Fuel supply problem
      1. Cannot maintain pressure due to pressure regulator malfunction
      2. Fuel injector leak
      3. Fuel leak from fuel line
      4. Fuel pump control circuit (Low pressure side)
      5. Fuel pump assembly
      35 to 49
      Ignition system malfunction
      1. Spark plug
      2. Crankshaft position sensor
      3. Ignition coil assembly
      Engine stalls after starter turnoff
      Air suction
      1. Intake system connections
      50 to 56
      Deposits in throttle body
      1. Throttle with motor body assembly
      VVT valve does not return properly
      1. Camshaft timing oil control valve
      Mass air flow meter malfunction
      1. Mass air flow meter
      The initial combustion and starter turnoff occur late
      Engine coolant temperature sensor malfunction
      1. Engine coolant temperature sensor
      57 to 71
      Mass air flow meter malfunction
      1. Mass air flow meter
      Abnormal A/F learned value
      1. Air fuel ratio sensor
      Deviation from fuel injection characteristics
      1. Fuel injector assembly (for port injection)
      Wet-fouled or dry-fouled spark plug
      1. Spark plug
      Lack of fuel pressure
      1. Pressure regulator
      2. Fuel pump assembly
      3. Fuel pump control circuit (low pressure side)

    2. Systems to Inspect

      Troubleshooting by System
      Suspected Area
      Suspected Component
      Procedure
      Fuel system troubleshooting A
      Abnormal A/F learned value
      1. Fuel injector assembly (for port injection)
      87 to 94
      95 to 102
      Rough idling
      1. Crankshaft position sensor
      Abnormal fuel pressure
      1. Fuel
      2. Fuel leak from fuel line
      3. Fuel pump assembly
      4. Pressure regulator
      Fuel system troubleshooting B
      Abnormal concentration of HC in surge tank
      1. Purge valve system
      2. Fuel injector assembly (for port injection)
      3. Intake valve
      103 to 105
      Fuel system troubleshooting C
      Injection signal system malfunction
      1. Fuel injector assembly (for port injection)
      2. Crankshaft position sensor
      3. VVT sensor
      4. ECM
      73 to 76
      Intake system troubleshooting
      Difference between ISC target value and opening angle when idling
      1. Engine assembly (compression loss)
      2. Valve timing
      3. Engine coolant temperature sensor
      4. ECM
      84 to 86
      106 to 108
      Ignition system troubleshooting
      Camshaft and/or crankshaft position sensor signal malfunction
      1. Crankshaft position sensor system (including sensor installation)
      2. VVT sensor system (including sensor installation)
      3. ECM
      77 to 83
      109 to 115

1.CHECK FOR ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.



    A103809E55
  1. Read the DTCs and record the freeze frame data.

    HINT:
    1. This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
    2. When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
    3. The fourth set of freeze frame data is the data recorded when the DTC is stored.


    Result 
    Result
    Proceed to
    Only DTC P1604 is output
    A
    DTCs other than P1604 are output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK ENGINE IMMOBILISER SYSTEM
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Immobiliser Fuel Cut.

  1. Read the value displayed on the GTS.

    OK:
    Immobiliser Fuel Cut is OFF.

    HINT:
    After reconnecting the battery cable, if the engine is started immediately (without waiting 1.8 seconds after turning the ignition switch to ON), the engine will stop (due to the key verification process). The engine can be started after that.



NG
REPAIR ENGINE IMMOBILISER SYSTEM
OK


3.CHECK MALFUNCTION CONDITION
  1. Confirm the problem symptoms.

    Result 
    Result
    Proceed to
    Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
    A
    The problem symptoms can be reproduced, or the malfunction conditions are known
    B



B
Go to step 25
A


4.CHECK FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Engine Speed
    Battery Voltage
    All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
    Minimum voltage is below 5 V
    Battery fully depleted
    A
    Minimum voltage is 5 V or higher
    1. Starter malfunction
    2. Crankshaft position sensor system
    3. Excess engine friction
    4. Engine immobiliser system
    5. ECM
    B
    60 to 250 rpm (engine cranks but no initial combustion)
    -
    1. Fuel pump control circuit (low pressure side)
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Engine immobiliser system
    5. Fuel injection system
    C
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
    -
    1. Engine assembly
    2. Fuel injection system
    3. Fuel pump control circuit (low pressure side)
    D

    HINT:
    When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the freeze frame data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
    *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
    *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
    1. Immobiliser Fuel Cut
    2. Engine Speed (Starter Off)
    3. Shift SW Status (R, D Range)



B
Go to step 5

C
Go to step 10

D
Go to step 15
A

CHARGE OR REPLACE BATTERY 

5.CHECK FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Battery Voltage
    Minimum voltage is 9 V or higher and voltage fluctuates*2, *3
    1. Crankshaft position sensor system
    2. ECM
    A
    Minimum voltage is 9 V or higher and voltage does not fluctuate*1
    Starter system
    B
    Minimum voltage is 5 to 9 V*4
    1. Excess engine friction
    2. Battery fully depleted
    C

    HINT:

    1. A217930E01
      *1: The 5 sets of freeze frame data show approximately the same battery voltage.
    2. *2: The 5 sets of freeze frame data show different battery voltages.
    3. *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
    4. *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
CHECK STARTER SIGNAL CIRCUIT (Click here)

C
CHECK AND REPAIR ENGINE OR BATTERY
A


6.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    Result 
    Result
    Proceed to
    Normal
    A
    Abnormal
    B



B
SECURELY REINSTALL SENSOR (Click here)
A


7.CHECK CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.

  1. Check for oil on the connector terminals.

    OK:
    No oil on the terminals.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) - C33-1 (NE+)
    Always
    Below 1 Ω
    A34-27 (NE-) - C33-2 (NE-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) or C33-1 (NE+) - Body ground
    Always
    10 kΩ or higher
    A34-27 (NE-) or C33-2 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

10.CHECK FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Ambient Temp for A/C, Intake Air
    Coolant Temp, Ambient Temp for A/C
    Fuel Pump Duty
    Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is 10°C or more*1
    Coolant Temp is 125°C or higher, or below Ambient Temp for A/C by 15°C or more
    -
    Engine coolant temperature sensor
    B
    Other than above
    No sets of freeze frame data are 0%
    -
    A
    At least 1 of the 5 sets of freeze frame data is 0%
    Fuel pump control circuit (low pressure side)
    C
    Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is less than 10°C*2
    -
    At least 1 of the 5 sets of freeze frame data is 0%
    Fuel pump control circuit (low pressure side)
    C
    No sets of freeze frame data are 0%
    -
    A

    HINT:
    1. *1: A long time had not elapsed after stopping the engine.
    2. *2: A long time had elapsed after stopping the engine.



B
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

C
CHECK FUEL PUMP CONTROL CIRCUIT (LOW PRESSURE SIDE) (Click here)
A


11.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:

    Control the Fuel Pump / Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
REPAIR FUEL PUMP CONTROL CIRCUIT (LOW PRESSURE SIDE)
OK


12.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)


    A280161E01
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C8-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    C30-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    C9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    C31-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)
    *b
    No. 1 cylinder
    *c
    No. 2 cylinder
    *d
    No. 3 cylinder
    *e
    No. 4 cylinder

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR FUEL INJECTOR POWER SOURCE CIRCUIT
OK


13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    No fuel leakage or signs of fuel leakage
    A
    Fuel leakage or signs of fuel leakage are present
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
REPAIR OR REPLACE FUEL LINE
A


14.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump assembly (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM 

15.CHECK FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Ambient Temp for A/C, Intake Air
    Coolant Temp, Ambient Temp for A/C
    Long FT
    Engine Speed
    Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is 10°C or more
    Coolant Temp is 125°C or higher, or below Ambient Temp for A/C by 15°C or more
    -
    -
    Engine coolant temperature sensor
    B
    Other than above
    -15% or less, or +15% or more
    -
    1. Fuel pump control circuit (low pressure side)
    2. Fuel injector assembly (for port injection)
    A
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is less than 300 rpm
    1. Fuel system
    2. Intake air system
    D
    Difference between Coolant Temp, Ambient Temp for A/C and Intake Air is less than 10°C
    -
    -15% or less, or +15% or more
    -
    1. Fuel pump control circuit (low pressure side)
    2. Fuel injector assembly (for port injection)
    A
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is less than 300 rpm
    1. Fuel system
    2. Intake air system
    D

    HINT:
    *1: Compression loss may have occurred in the engine assembly.



B
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

C
CHECK AND REPAIR ENGINE

D
Go to step 18
A


16.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Check that no carbon is stuck to the fuel injector assembly (for port injection).

    OK:
    No carbon present.



NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
OK


17.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump assembly (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM 

18.CHECK FREEZE FRAME DATA
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    Engine coolant temperature is 40°C or less*1
    Pressure regulator
    A
    Engine coolant temperature is 40 to 90°C*2
    Fuel injector
    B
    Engine coolant temperature is 90°C or higher*3
    Pressure regulator
    A

    HINT:
    *1: If the engine coolant temperature is 40°C or less (after stopping the engine and the vehicle has not been driven for a long period of time), the pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
    *2: If the engine coolant temperature is 40 to 90°C (15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector.
    *3: If the engine coolant temperature is 90°C or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.



B
Go to step 20
A


19.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, read the values after cranking the engine.


    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
Go to step 24
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

20.CHECK FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    4000 ppm or more
    A
    Less than 4000 ppm
    B

    HINT:
    If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.



B
Go to step 22
A


21.CHECK FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Inspect the fuel injector assemblies (for port injection) (Click here).

    Result 
    Result
    Proceed to
    Normal
    A
    Abnormal
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
A


22.CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the airflow passage.

    Result 
    Result
    Proceed to
    No carbon present
    A
    Carbon in passage
    B



B
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


23.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


24.PERFORM SIMULATION TEST
  1. Check if the engine can be started.

    Result 
    Result
    Proceed to
    Engine cannot be started
    A
    Engine can be started
    B



B
END
A


25.CONFIRM PROBLEM SYMPTOM
  1. Confirm the problem symptoms.

    HINT:
    The problem symptoms below can be determined by reading the freeze frame data.


    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    The engine does not crank
    1. Battery fully depleted
    2. Starter assembly (includes pinion gear wear or tooth damage)
    3. Starter system
    4. Engine assembly (excess friction)
    5. Flywheel wear or tooth damage (for Manual Transmission)
    6. Drive plate wear or tooth damage (for Automatic Transmission)
    A
    Abnormal cranking speed
    1. Battery fully depleted
    2. Starter assembly
    3. Engine assembly (excess friction, compression loss)
    B
    There is no initial combustion (combustion does not occur even once)*1
    1. Pressure regulator fuel pressure maintenance
    2. Fuel injector leak
    3. Fuel leak from fuel line
    4. Fuel pump control circuit (low pressure side)
    5. Fuel pump assembly
    6. Spark plug
    7. Crankshaft position sensor system
    8. Ignition coil system
    C
    The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve
    4. Mass air flow meter system
    D
    The initial combustion and starter turnoff occur late*3
    1. Engine coolant temperature sensor
    2. Mass air flow meter
    3. Air fuel ratio sensor
    4. Heated oxygen sensor
    5. Fuel injector assembly (for port injection)
    6. Spark plug
    7. Pressure regulator
    8. Fuel pump assembly
    9. Fuel pump control circuit (low pressure side)
    E

    HINT:
    1. If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
    2. *1: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
    3. *2: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve may have a problem returning.
    4. *3: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).



B
Go to step 32

C
Go to step 35

D
Go to step 50

E
Go to step 57
A


26.PERFORM SIMULATION TEST
  1. When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely*1
    1. Battery
    2. Excess engine friction
    3. Starter assembly
    A
    A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely
    1. Fly wheel (for Manual Transmission)
    2. Drive plate (for Automatic Transmission)
    3. Starter assembly
    B
    A noise indicating that the starter pinion gear is extending is not heard
    1. Battery
    2. Starter assembly
    3. Starter system
    C

    HINT:
    *1: The battery may be fully depleted or there may be excess engine friction.



B
Go to step 29

C
Go to step 30
A


27.INSPECT BATTERY


    A086946E01
  1. Check the electrolyte quantity.

    OK:
    Electrolyte quantity is within the specified range.

  1. Inspect the specific gravity.

    1. Inspect the specific gravity of each cell.

      Standard specific gravity:
      1.25 to 1.29 (electrolyte is at 20°C (68°F))

      HINT:
      1. If the result is not as specified, recharge or replace the battery.
      2. It is not necessary to inspect a maintenance-free battery.

  1. Inspect the battery voltage.

    1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

    2. Measure the battery voltage.

      Standard voltage:
      12.5 to 12.9 V (electrolyte is at 20°C (68°F))

      HINT:
      If the result is not as specified, recharge or replace the battery.

    3. Measure the battery voltage when cranking the engine.

      Standard:
      Approximately 6 V or higher (0°C (32°F) or higher)

      HINT:
      When the battery is depleted, the horn becomes quieter.



NG
CHARGE OR REPLACE BATTERY
OK


28.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.


    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal (for Automatic Transmission)
    B
    Normal (for Manual Transmission)
    C

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
INSPECT STARTER ASSEMBLY (Click here)

C
INSPECT STARTER ASSEMBLY (Click here)
A

REPAIR OR REPLACE ENGINE ASSEMBLY 

29.CHECK STARTER ASSEMBLY
  1. Remove the starter assembly (for Automatic Transmission) (Click here).

  1. Remove the starter assembly (for Manual Transmission) (Click here).

  1. Check for starter pinion gear wear and damage.

    OK:
    There is no wear or damage.


    Result 
    Result
    Proceed to
    Abnormal (for Automatic Transmission)
    A
    Abnormal (for Manual Transmission)
    B
    Normal (for Automatic Transmission)
    C
    Normal (for Manual Transmission)
    D



B
REPLACE STARTER ASSEMBLY (Click here)

C
REPLACE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (Click here)

D
REPLACE FLYWHEEL SUB-ASSEMBLY (Click here)
A

REPLACE STARTER ASSEMBLY (Click here)  

30.INSPECT BATTERY


    A086946E01
  1. Check the electrolyte quantity.

    OK:
    Electrolyte quantity is within the specified range.

  1. Inspect the specific gravity.

    1. Inspect the specific gravity of each cell.

      Standard specific gravity:
      1.25 to 1.29 (electrolyte is at 20°C (68°F))

      HINT:
      1. If the result is not as specified, recharge or replace the battery.
      2. It is not necessary to inspect a maintenance-free battery.

  1. Inspect the battery voltage.

    1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

    2. Measure the battery voltage.

      Standard voltage:
      12.5 to 12.9 V (electrolyte is at 20°C (68°F))

      HINT:
      If the result is not as specified, recharge or replace the battery.

    3. Measure the battery voltage when cranking the engine.

      Standard:
      Approximately 6 V or higher (0°C (32°F) or higher)

      HINT:
      When the battery is depleted, the horn becomes quieter.



NG
CHARGE OR REPLACE BATTERY
OK


31.INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (for Automatic Transmission) (Click here).

  1. Inspect the starter assembly (for Manual Transmission) (Click here).


Result 
Result
Proceed to
Normal
A
Abnormal (for Automatic Transmission)
B
Abnormal (for Manual Transmission)
C


B
REPLACE STARTER ASSEMBLY (Click here)

C
REPLACE STARTER ASSEMBLY (Click here)
A

CHECK STARTER SIGNAL CIRCUIT (Click here)  

32.PERFORM SIMULATION TEST
  1. Check the cranking speed.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Cranking speed is slow (100 rpm or less)
    1. Battery
    2. Starter assembly
    3. Excess engine friction
    A
    Cranking speed is fast (300 rpm or more)*1
    Engine compression loss
    B

    HINT:
    *1: If the cranking speed is fast, there may be compression loss.



B
CHECK AND REPAIR ENGINE ASSEMBLY
A


33.INSPECT BATTERY


    A086946E01
  1. Check the electrolyte quantity.

    OK:
    Electrolyte quantity is within the specified range.

  1. Inspect the specific gravity.

    1. Inspect the specific gravity of each cell.

      Standard specific gravity:
      1.25 to 1.29 (electrolyte is at 20°C (68°F))

      HINT:
      1. If the result is not as specified, recharge or replace the battery.
      2. It is not necessary to inspect a maintenance-free battery.

  1. Inspect the battery voltage.

    1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

    2. Measure the battery voltage.

      Standard voltage:
      12.5 to 12.9 V (electrolyte is at 20°C (68°F))

      HINT:
      If the result is not as specified, recharge or replace the battery.

    3. Measure the battery voltage when cranking the engine.

      Standard:
      Approximately 6 V or higher (0°C (32°F) or higher)

      HINT:
      When the battery is depleted, the horn becomes quieter.



NG
CHARGE OR REPLACE BATTERY
OK


34.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.


    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal (for Automatic Transmission)
    B
    Normal (for Manual Transmission)
    C

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
INSPECT STARTER ASSEMBLY (Click here)

C
INSPECT STARTER ASSEMBLY (Click here)
A

REPAIR OR REPLACE ENGINE ASSEMBLY 

35.CHECK FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Using a sound scope or screwdriver, check for fuel injector operating noise while cranking the engine.

    OK:
    Fuel injector operating noise is heard.



NG
Go to step 48
OK


36.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)
  1. Inspect the fuel pressure .



NG
Go to step 46
OK


37.CHECK SPARK PLUG AND SPARK
  1. Check for sparks .



NG
Go to step 41
OK


38.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.
    *4: From step 72, perform fuel system troubleshooting C (steps 73 to 76).



B
Go to step 40

C
Go to step 72
A


39.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 72, perform fuel system troubleshooting C (steps 73 to 76).



B
Go to step 72
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

40.CHECK FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    4000 ppm or more
    A
    Less than 4000 ppm
    B*1

    HINT:
    1. If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
    2. *1: From step 72, perform fuel system troubleshooting C (steps 73 to 76).



B
Go to step 72
A

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)  

41.CHECK SPARK PLUG
  1. Inspect the spark plugs .

HINT:
Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.



NG
REPLACE SPARK PLUG (Click here)
OK


42.READ VALUE USING GTS (ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the value of Engine Speed.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
CHECK CRANKSHAFT POSITION SENSOR CIRCUIT
OK


43.CHECK TERMINAL VOLTAGE (IGNITION COIL POWER SOURCE)


    A325105E01
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C44-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C42-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C45-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C43-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)
    *b
    No. 1 cylinder
    *c
    No. 2 cylinder
    *d
    No. 3 cylinder
    *e
    No. 4 cylinder

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK IGNITION COIL POWER SOURCE CIRCUIT
OK


44.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A36-21 (IGT1) - C44-2 (IGT1)
    Always
    Below 1 Ω
    A36-10 (IGT2) - C42-2 (IGT2)
    Always
    Below 1 Ω
    A36-31 (IGT3) - C45-2 (IGT3)
    Always
    Below 1 Ω
    A36-8 (IGT4) - C43-2 (IGT4)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A36-21 (IGT1) or C44-2 (IGT1) - Body ground
    Always
    10 kΩ or higher
    A36-10 (IGT2) or C42-2 (IGT2) - Body ground
    Always
    10 kΩ or higher
    A36-31 (IGT3) or C45-2 (IGT3) - Body ground
    Always
    10 kΩ or higher
    A36-8 (IGT4) or C43-2 (IGT4) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


45.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
  1. Disconnect the ignition coil assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    C44-3 (GND) - Body ground
    Always
    Below 1 Ω
    C42-3 (GND) - Body ground
    Always
    Below 1 Ω
    C45-3 (GND) - Body ground
    Always
    Below 1 Ω
    C43-3 (GND) - Body ground
    Always
    Below 1 Ω

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the ignition coil assembly, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform troubleshooting for the ignition system (steps 78 to 83).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)  

46.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:

    Control the Fuel Pump / Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (LOW PRESSURE SIDE) (Click here)
OK


47.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform fuel system troubleshooting C (steps 73 to 77).



B
CHECK FUEL PUMP CONTROL CIRCUIT (LOW PRESSURE SIDE) (Click here)
A

REPAIR OR REPLACE FUEL LINE 

48.READ VALUE USING GTS (ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the value of Engine Speed.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


49.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)


    A280161E01
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C8-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    C30-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    C9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    C31-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)
    *b
    No. 1 cylinder
    *c
    No. 2 cylinder
    *d
    No. 3 cylinder
    *e
    No. 4 cylinder

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR FUEL INJECTOR POWER SOURCE CIRCUIT
OK


50.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
Go to step 57
OK


51.CHECK INTAKE SYSTEM
  1. Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).

    HINT:
    1. If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
    2. If Short FT and Long FT are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when racing the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.

    OK:
    There is no air leakage.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


52.CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Disconnect the throttle with motor body assembly connector.

    HINT:
    When the connector is disconnected, the vehicle enters fail-safe mode.

  1. Crank the engine and check that it starts.

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start
    B

  1. Connect the throttle with motor body assembly connector.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



B
Go to step 54
A


53.CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the airflow passage.

    OK:
    No carbon present.



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


54.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT LINEAR)
  1. Connect the GTS to the DLC3.

  1. Turn the GTS on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank1) or Control the VVT Linear (Bank2).

    HINT:
    When performing the Active Test, make sure the vehicle is stopped.

  1. Check the engine speed while operating the camshaft timing oil control valve using the GTS.

    OK:

    GTS Operation
    Specified Condition
    0 deg (CA)
    Normal engine speed
    36 deg (CA)
    Engine idles roughly or stalls

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    3. If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause the engine to stall.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE (FOR INTAKE SIDE) (Click here)
OK


55.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR)
  1. Connect the GTS to the DLC3.

  1. Turn the GTS on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).

    HINT:
    When performing the Active Test, make sure the vehicle is stopped.

  1. Check the engine speed while operating the camshaft timing oil control valve using the GTS.

    OK*1:

    GTS Operation
    Specified Condition
    0 deg (CA)
    Normal engine speed
    51 deg (CA)
    Engine idles roughly or stalls


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

    HINT:
    1. *1: From step 72, perform intake system troubleshooting (steps 84 to 86). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 87 to 94).
    2. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    3. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    4. If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause the engine to stall.



B
Go to step 72
A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST SIDE) (Click here)  

56.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-22 (VG) - C16-5 (VG)
    Always
    Below 1 Ω
    A33-29 (E2G) - C16-4 (E2G)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-22 (VG) or C16-5 (VG) - Body ground
    Always
    10 kΩ or higher
    A33-29 (E2G) or C16-4 (E2G) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform intake system troubleshooting (steps 84 to 86). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 87 to 94).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)  

57.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


58.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A36-30 (THW) - C40-2 (THW)
    Always
    Below 1 Ω
    A36-29 (E1) - C40-1 (E2)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A36-30 (THW) or C40-2 (THW) - Body ground
    Always
    10 kΩ or higher
    A36-29 (E1) or C40-1 (E2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


59.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).

    HINT:
    If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


60.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-22 (VG) - C16-5 (VG)
    Always
    Below 1 Ω
    A33-29 (E2G) - C16-4 (E2G)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-22 (VG) or C16-5 (VG) - Body ground
    Always
    10 kΩ or higher
    A33-29 (E2G) or C16-4 (E2G) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


61.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Long FT.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT
    +25% or more or less than -25%
    1. Air fuel ratio sensor
    2. Heated oxygen sensor
    3. Mass air flow meter
    4. Fuel injector assembly (for port injection)
    5. ECM
    A
    Atmosphere Pressure
    80 kPa or less (when elevation is 0 m)
    Both Data List items listed above
    Values are other than above
    -
    B



B
Go to step 65
A


62.PERFORM SIMULATION TEST
  1. Remove the EFI MAIN and ETCS fuses from the engine room relay block assembly.

  1. After 60 seconds or more elapse, install the EFI MAIN and ETCS fuses.

  1. Check if the engine can be started.

    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 65
A


63.INSPECT AIR FUEL RATIO SENSOR
A248258E01
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel System Status #1.

  1. Confirm that Fuel System Status #1 is CL.

  1. Enter the following menus: Powertrain / Engine / Data List / AF Lambda B1S1.

  1. Confirm that AF Lambda B1S1 is both within the range of 0.95 to 1.05 when idling.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F sensor.

  1. Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

    Standard:

    GTS Display
    Injection Volume
    Specified Condition
    AFS Voltage B1S1
    +12.5%
    Air fuel ratio sensor output voltage is below 2.0 V
    -12.5%
    Air fuel ratio sensor output voltage is higher than 2.4 V


    Result 
    Result
    Proceed to
    Normal
    A
    Abnormal
    B

    HINT:
    1. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    2. If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.



B
REPLACE AIR FUEL RATIO SENSOR (Click here)
A


64.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine.

    OK:
    Speed is stable.

    HINT:
    After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.



NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
OK

REPLACE MASS AIR FLOW METER (Click here)  

65.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)
  1. Inspect the fuel pressure .



NG
Go to step 71
OK


66.CHECK SPARK PLUG
  1. Inspect the spark plugs .

    Result 
    Result
    Proceed to
    All cylinders are normal
    A
    One cylinder is abnormal*1
    B
    All cylinders are abnormal*2, *3
    C

HINT:
  1. *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.
  2. *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.
  3. *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.



B
REPLACE SPARK PLUG (ABNORMAL CYLINDER) (Click here)

C
REPLACE SPARK PLUG (ALL) (Click here)
A


67.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.
    *4: From step 72, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.



B
Go to step 69

C
Go to step 72
A


68.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 72, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.



B
Go to step 72
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

69.CHECK PURGE VALVE


    A280186
  1. Disconnect the purge hose (on the canister side) of the purge valve.

  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the connector of the purge valve.

  1. Check if air flows through the purge valve.

    OK:
    Air does not flow.

  1. Connect the connector of the purge valve.

  1. Connect the purge hose of the purge valve.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


70.CHECK FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    4000 ppm or more
    A
    Less than 4000 ppm
    B*1

    HINT:
    1. If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
    2. *1: From step 72, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.



B
Go to step 72
A

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)  

71.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.



B
CHECK FUEL PUMP CONTROL CIRCUIT (LOW PRESSURE SIDE) (Click here)
A

REPAIR OR REPLACE FUEL LINE 

72.CHECK MALFUNCTION CONDITION
  1. If the malfunction could not be identified during the inspections in steps 38, 39, 40 and 47, perform fuel system troubleshooting C (steps 73 to 76).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 38, 39, 40 and 47
    Fuel system troubleshooting C
    73 to 76
    A

  1. If the malfunction could not be identified during the inspection in step 45, perform ignition system troubleshooting (steps 77 to 83).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 45
    Ignition system troubleshooting
    77 to 83
    B

  1. If the malfunction could not be identified during the inspections in steps 55, 56 and 57, perform intake air system troubleshooting (steps 84 to 86). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 87 to 94).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 55, 56, 57
    Intake air system troubleshooting
    84 to 86
    C
    Fuel system troubleshooting A
    87 to 94

  1. If the malfunction could not be identified during the inspections in steps 58, 59, 60, 63, 64, 66, 67, 68, 70 and 71, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake air system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 115), in that order.

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 57, 58, 59, 60, 63, 64, 66, 67, 68, 70 and 71
    Fuel system troubleshooting A
    95 to 102
    D
    Fuel system troubleshooting B
    103 to 105
    Intake air system troubleshooting
    106 to 108
    Ignition system troubleshooting
    109 to 115



B
Go to step 77

C
Go to step 84

D
Go to step 95
A


73.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Inspect the fuel injector assemblies (for port injection) (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
OK


74.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)


    A280161E01
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C8-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    C30-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    C9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    C31-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)
    *b
    No. 1 cylinder
    *c
    No. 2 cylinder
    *d
    No. 3 cylinder
    *e
    No. 4 cylinder

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR FUEL INJECTOR POWER SOURCE CIRCUIT
OK


75.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.


    Result:

    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
A


76.CHECK VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE) 

77.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


78.CHECK VVT SENSOR
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


79.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) - C33-1 (NE+)
    Always
    Below 1 Ω
    A34-27 (NE-) - C33-2 (NE-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) or C33-1 (NE+) - Body ground
    Always
    10 kΩ or higher
    A34-27 (NE-) or C33-2 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


80.CHECK HARNESS AND CONNECTOR (VVT SENSOR (INTAKE SIDE) - ECM)


    A289487E02
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C12-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C26-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*A
Bank 1
*B
Bank 2
*a
Front view of wire harness connector
(to VVT Sensor (Intake Side))
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-26 (VV1+) - C12-2 (VV1+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C12-3 (VV1-)
    Always
    Below 1 Ω
    A34-15 (VV2+) - C26-2 (VV2+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C26-3 (VV2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-26 (VV1+) or C12-2 (VV1+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C12-3 (VV1-) - Body ground
    Always
    10 kΩ or higher
    A34-15 (VV2+) or C26-2 (VV2+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C26-3 (VV2-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


81.CHECK HARNESS AND CONNECTOR (VVT SENSOR (EXHAUST SIDE) - ECM)


    A289488E02
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C6-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C25-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*A
Bank 1
*B
Bank 2
*a
Front view of wire harness connector
(to VVT Sensor (Exhaust Side))
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-14 (EV1+) - C6-2 (EV1+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C6-3 (EV1-)
    Always
    Below 1 Ω
    A34-25 (EV2+) - C25-2 (EV2+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C25-3 (EV2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-14 (EV1+) or C6-2 (EV1+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C6-3 (EV1-) - Body ground
    Always
    10 kΩ or higher
    A34-25 (EV2+) or C25-2 (EV2+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C25-3 (EV2-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


82.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.


    Result:

    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
A


83.CHECK VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE) 

84.READ VALUE USING GTS (ISC LEARNING VALUE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches off.

  1. Enter the following menus: Powertrain / Engine / Data List / ISC Learning Value.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    ISC Learning Value
    (engine displacement (liters) x 0.9) or more
    1. Valve timing
    2. Compression
    A
    Less than (engine displacement (liters) x 0.9)
    -
    B



B
Go to step 86
A


85.CHECK CYLINDER COMPRESSION PRESSURE
  1. Inspect the compression .



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

ADJUST VALVE TIMING (Click here)  

86.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


87.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

    Result 
    Vehicle State
    Specified Condition
    Cranking engine
    304 to 343 kPa (3.1 to 3.5 kgf/cm2)
    5 minutes after stopping engine
    147 kPa (1.5 kgf/cm2) or higher



NG
Go to step 93
OK


88.READ VALUE USING GTS (LONG FT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Long FT.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
A


89.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


90.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


91.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) - C33-1 (NE+)
    Always
    Below 1 Ω
    A34-27 (NE-) - C33-2 (NE-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) or C33-1 (NE+) - Body ground
    Always
    10 kΩ or higher
    A34-27 (NE-) or C33-2 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


92.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

93.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    No fuel leakage or signs of fuel leakage
    A
    Fuel leakage or signs of fuel leakage are present
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
REPAIR OR REPLACE FUEL LINE
A


94.INSPECT FUEL PUMP ASSEMBLY
  1. Inspect the fuel pump assembly (Click here).

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump assembly and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.



NG
REPLACE FUEL PUMP ASSEMBLY (Click here)
OK

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

95.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    A
    Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    B



B
Go to step 101
A


96.READ VALUE USING GTS (LONG FT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Long FT.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
A


97.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


98.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


99.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) - C33-1 (NE+)
    Always
    Below 1 Ω
    A34-27 (NE-) - C33-2 (NE-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) or C33-1 (NE+) - Body ground
    Always
    10 kΩ or higher
    A34-27 (NE-) or C33-2 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


100.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

101.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    No fuel leakage or signs of fuel leakage
    A
    Fuel leakage or signs of fuel leakage are present
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
REPAIR OR REPLACE FUEL LINE
A


102.INSPECT FUEL PUMP ASSEMBLY
  1. Inspect the fuel pump assembly (Click here).

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump assembly and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.



NG
REPLACE FUEL PUMP ASSEMBLY (Click here)
OK


103.CHECK PURGE VALVE


    A280186
  1. Disconnect the vacuum hose (on the canister side) of the purge valve.

  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the connector of the purge valve.

  1. Check if air flows through the purge valve.

    OK:
    Air does not flow

  1. Connect the connector of the purge valve.

  1. Connect the vacuum hose of the purge valve.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
INSPECT PURGE VALVE (Click here)
OK


104.CHECK FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    Less than 4000 ppm
    A
    4000 ppm or more
    B

    HINT:
    If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.



B
REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) (Click here)
A


105.CHECK INTAKE VALVE
  1. Check if carbon is on the intake valves.

    Result 
    Result
    Proceed to
    No carbon present
    A
    Carbon present
    B



B
CLEAN INTAKE VALVE
A


106.READ VALUE USING GTS (ISC LEARNING VALUE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

  1. Enter the following menus: Powertrain / Engine / Data List / ISC Learning Value.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    ISC Learning Value
    (engine displacement (liters) x 0.9) or more
    1. Valve timing
    2. Compression
    A
    Less than (engine displacement (liters) x 0.9)
    -
    B



B
Go to step 108
A


107.CHECK CYLINDER COMPRESSION PRESSURE
  1. Inspect the compression .



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

ADJUST VALVE TIMING (Click here)  

108.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


109.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


110.CHECK VVT SENSOR
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


111.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) - C33-1 (NE+)
    Always
    Below 1 Ω
    A34-27 (NE-) - C33-2 (NE-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) or C33-1 (NE+) - Body ground
    Always
    10 kΩ or higher
    A34-27 (NE-) or C33-2 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


112.CHECK HARNESS AND CONNECTOR (VVT SENSOR (INTAKE SIDE) - ECM)


    A289487E02
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C12-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C26-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*A
Bank 1
*B
Bank 2
*a
Front view of wire harness connector
(to VVT Sensor (Intake Side))
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-26 (VV1+) - C12-2 (VV1+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C12-3 (VV1-)
    Always
    Below 1 Ω
    A34-15 (VV2+) - C26-2 (VV2+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C26-3 (VV2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-26 (VV1+) or C12-2 (VV1+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C12-3 (VV1-) - Body ground
    Always
    10 kΩ or higher
    A34-15 (VV2+) or C26-2 (VV2+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C26-3 (VV2-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


113.CHECK HARNESS AND CONNECTOR (VVT SENSOR (EXHAUST SIDE) - ECM)


    A289488E02
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C6-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V
    C25-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*A
Bank 1
*B
Bank 2
*a
Front view of wire harness connector
(to VVT Sensor (Exhaust Side))
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-14 (EV1+) - C6-2 (EV1+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C6-3 (EV1-)
    Always
    Below 1 Ω
    A34-25 (EV2+) - C25-2 (EV2+)
    Always
    Below 1 Ω
    A34-34 (VVE) - C25-3 (EV2-)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-14 (EV1+) or C6-2 (EV1+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C6-3 (EV1-) - Body ground
    Always
    10 kΩ or higher
    A34-25 (EV2+) or C25-2 (EV2+) - Body ground
    Always
    10 kΩ or higher
    A34-34 (VVE) or C25-3 (EV2-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


114.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.


    Result:

    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)
A


115.CHECK VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE)