Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here



AIR CONDITIONING SYSTEM: 
Symptom
Suspected Area
See page
All functions of the A/C system do not operate
1. IG power source circuit
Click here
2. Back-up power source circuit
Click here
3. Heater control panel power source circuit
Click here
4. LIN communication circuit
Click here
5. Steering pad switch circuit
Click here
6. Heater control base sub-assembly
Click here
7. A/C amplifier
Click here
Air Flow Control: No blower operation
1. Blower motor circuit
Click here
2. Heater control panel power source circuit
Click here
3. LIN communication circuit
Click here
4. Heater control base sub-assembly
Click here
5. A/C amplifier
Click here
Air Flow Control: No blower control
1. Blower motor circuit
Click here
2. Heater control panel power source circuit
Click here
3. LIN communication circuit
Click here
4. Heater control base sub-assembly
Click here
5. A/C amplifier
Click here
Air Flow Control: Insufficient air flow
1. Blower motor circuit
Click here
2. A/C amplifier
Click here
Temperature Control: No cool air comes out
1. Refrigerant volume
Click here
2. Refrigerant pressure
Click here
3. Pressure switch circuit
Click here
4. Air conditioning compressor magnetic clutch circuit (for 2GR-FE)
Click here
5. Compressor lock sensor circuit (for 2GR-FE)
Click here
6. Compressor solenoid circuit
Click here
7. Air mix control servo motor circuit (Driver side)
Click here
8. Air mix control servo motor circuit (Passenger side)
Click here
9. Evaporator temperature sensor circuit
Click here
10. Room temperature sensor circuit
Click here
11. Ambient temperature sensor circuit
Click here
12. Heater control panel power source circuit
Click here
13. LIN communication circuit
Click here
14. Expansion valve
Click here
15. Heater control base sub-assembly
Click here
16. A/C amplifier
Click here
17. ECM (for 2AZ-FE)
Click here
18. ECM (for 2GR-FE)
Click here
Temperature Control: No warm air comes out
1. Air mix control servo motor circuit (Driver side)
Click here
2. Air mix control servo motor circuit (Passenger side)
Click here
3. Evaporator temperature sensor circuit
Click here
4. Room temperature sensor circuit
Click here
5. Ambient temperature sensor circuit
Click here
6. A/C amplifier
Click here
Temperature Control: Output air is warmer or cooler than the set temperature or response is slow.
1. Refrigerant volume
Click here
2. Refrigerant pressure
Click here
3. Solar sensor circuit (Driver side)
Click here
4. Solar sensor circuit (Passenger side)
Click here
5. Room temperature sensor circuit
Click here
6. Ambient temperature sensor circuit
Click here
7. Air mix control servo motor circuit (Driver side)
Click here
8. Air mix control servo motor circuit (Passenger side)
Click here
9. Radiator unit sub-assembly
Click here
10. Expansion valve
Click here
11. A/C amplifier
Click here
Temperature control: No temperature control (only Max. cool or Max. warm)
1. Air mix control servo motor circuit (Driver side)
Click here
2. Air mix control servo motor circuit (Passenger side)
Click here
3. Room temperature sensor circuit
Click here
4. Ambient temperature sensor circuit
Click here
5. Evaporator temperature sensor circuit
Click here
6. Solar sensor circuit (Driver side)
Click here
7. Solar sensor circuit (Passenger side)
Click here
8. Heater control base sub-assembly
Click here
9. A/C amplifier
Click here
No air inlet control
1. Air inlet control servo motor circuit
Click here
2. A/C amplifier
Click here
No air flow mode control
1. Air outlet control servo motor circuit
Click here
2. A/C amplifier
Click here
Engine idle up does not occur, or is continuous
1. Air conditioning compressor magnetic clutch circuit (for 2GR-FE)
Click here
2. Compressor lock sensor circuit (for 2GR-FE)
Click here
3. Compressor solenoid circuit
Click here
4. Heater control panel power source circuit
Click here
5. LIN communication circuit
Click here
6. Heater control base sub-assembly
Click here
7. A/C amplifier
Click here
8. ECM (for 2AZ-FE)
Click here
9. ECM (for 2GR-FE)
Click here
Blinking of A/C indicator
1. Compressor solenoid circuit
Click here
2. A/C amplifier
Click here
Unable to control A/C with the steering pad switch
1. Steering pad switch circuit
Click here
2. Heater control panel power source circuit
Click here
3. LIN communication circuit
Click here
4. Heater control base sub-assembly
Click here
5. A/C amplifier
Click here
Plasmacluster indicator does not come on (Plasmacluster does not operate)
1. Blower motor circuit
Click here
2. Plasmacluster circuit
Click here
3. A/C amplifier
Click here
Diagnostic trouble codes are not recorded. Set mode is cleared when ignition switch is turned OFF.
1. Back-up power source circuit
Click here
2. A/C amplifier
Click here