Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM J

N04C-WA ENGINE CONTROL  ECD SYSTEM  Black Smoke Emitted  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.CHECK DTC OUTPUT (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
No output A
DTCs related to engine B



A

2.READ VALUE USING GTS (INJECTION VOLUME AND FCCB INJECTION FEEDBACK VAL #1 TO #4)

B

2.READ VALUE USING GTS (INJECTION VOLUME AND FCCB INJECTION FEEDBACK VAL #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.


e.

Enter the following menus in order and read the values.

·

Injection Volume

·

FCCB Injection Feedback Val #1, #2, #3, and #4


Standard:
Item Engine Speed* Reference Value
Injection Volume Idling (No engine load) 5 to 16 mm3/st
FCCB Injection Feedback Val #1 Idling (No engine load) -7.0 to 7.0 mm3/st
FCCB Injection Feedback Val #2 Idling (No engine load) -7.0 to 7.0 mm3/st
FCCB Injection Feedback Val #3 Idling (No engine load) -7.0 to 7.0 mm3/st
FCCB Injection Feedback Val #4 Idling (No engine load) -7.0 to 7.0 mm3/st


HINT:

*: The shift lever should be in the neutral position, and the A/C switch and all accessory switches should be off.



Result:
Proceed to
OK
NG



OK

3.PERFORM ENGINE RPM ACCELERATION

NG

11.INSPECT ECM (THW TERMINAL VOLTAGE)
3.PERFORM ENGINE RPM ACCELERATION
HINT:

If the exhaust gas contains excessive black smoke, perform the following operations:


a.

Accelerate the engine speed to the maximum rpm with no load 20 times.


b.

Check the volume of black smoke in the exhaust gas.

Result:
Result Proceed to
Black smoke is not present A
Black smoke remains in the exhaust gas B


HINT:

Soot deposits in the exhaust system may cause excessive black smoke.




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
4.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

Result:
Proceed to
OK
NG



OK

5.INSPECT EXHAUST RETARDER ASSEMBLY

NG

CHECK AND REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

5.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)

NG

REPLACE EXHAUST RETARDER ASSEMBLY

6.INSPECT TURBOCHARGER SUB-ASSEMBLY (PRESSURE)

Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

7.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List.


d.

Enter the following menus in order and read the values.

·

Common Rail Pressure

·

Injection Volume

·

FCCB Injection Feedback Value #1, #2, #3, and #4


Standard:
Item Engine Speed* Reference Value
Common Rail Pressure Idling 25000 to 35000 kPa
Injection Volume Idling 5 to 16 mm3/st
FCCB Injection Feedback Value #1 Idling -7.0 to 7.0 mm3/st
FCCB Injection Feedback Value #2 Idling -7.0 to 7.0 mm3/st
FCCB Injection Feedback Value #3 Idling -7.0 to 7.0 mm3/st
FCCB Injection Feedback Value #4 Idling -7.0 to 7.0 mm3/st


HINT:

*: The shift lever should be in neutral, and the A/C switch and all accessory switches should be OFF.



Result:
Result Proceed to
Within reference value A
One of FCCB Injection Feedback Value #1 to #4 is not within reference value B
Other result C



A

8.CHECK CYLINDER COMPRESSION PRESSURE

B

C

11.INSPECT ECM (THW TERMINAL VOLTAGE)
8.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>N04C-WA (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

9.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the injector assembly connectors.


b.

Disconnect the ECM connectors.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i5-1 - E-15 Always Below 1 Ω
i5-2 - E-14 Always Below 1 Ω
i8-1 - E-16 Always Below 1 Ω
i8-2 - E-34 Always Below 1 Ω
i6-1 - E-20 Always Below 1 Ω
i6-2 - E-38 Always Below 1 Ω
i7-1 - E-19 Always Below 1 Ω
i7-2 - E-18 Always Below 1 Ω
i5-1 or E-15 - Body ground Always 10 kΩ or higher
i5-2 or E-14 - Body ground Always 10 kΩ or higher
i8-1 or E-16 - Body ground Always 10 kΩ or higher
i8-2 or E-34 - Body ground Always 10 kΩ or higher
i6-1 or E-20 - Body ground Always 10 kΩ or higher
i6-2 or E-38 - Body ground Always 10 kΩ or higher
i7-1 or E-19 - Body ground Always 10 kΩ or higher
i7-2 or E-18 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER FUEL CUT #1 TO #4)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER FUEL CUT #1 TO #4)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Cylinder Fuel Cut #1 to #4.

HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Result Proceed to
Engine idling condition becomes unstable A
Engine idling condition does not change B



A

B

11.INSPECT ECM (THW TERMINAL VOLTAGE)
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C05
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-66 - M-54 Idling, engine coolant temperature between 80 to 120°C (176 to 248°F) 0.2 to 1.0 V



Result:
Proceed to
OK
NG



OK

12.INSPECT ECM (PIM TERMINAL VOLTAGE)

NG

18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
12.INSPECT ECM (PIM TERMINAL VOLTAGE)
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


Disconnect the ECM.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-77 - E-67 Negative pressure of 93 kPa [abs] (697 mmHg, 27.5 in.Hg) applied 0.25 to 0.4 V
Positive pressure of 150 kPa [abs] (1125 mmHg, 44.3 in.Hg) applied 1.0 to 1.4 V



Result:
Proceed to
OK
NG



OK

13.INSPECT CRANKSHAFT POSITION SENSOR

NG

19.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
13.INSPECT CRANKSHAFT POSITION SENSOR
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Start the engine.


d.

While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.

A407889E03
0.479,1.063 0.938,1.26 0.458,0.198 10 false G 0.406,1.75 1.396,2.198 0.99,0.448 10 false NE 3.167,2.469 4.219,2.688 1.052,0.219 10 false 20 ms/DIV. 3.458,0.052 4.51,0.271 1.052,0.219 10 false 720° 6.427,0.135 7.021,0.427 0.594,0.292 10 false 5 V/DIV. 6.625,1.135 7.156,1.438 0.531,0.302 10 false GND 6.625,1.771 7.156,2.073 0.531,0.302 10 false GND

Standard:
Tester Connection Condition Specified Condition
E-52 - E-72 Engine idling Correct waveform appears as shown
E-73 - E-54 Engine idling Correct waveform appears as shown



Result:
Proceed to
OK
NG



OK

14.INSPECT ECM (VPA AND VPA2 TERMINAL VOLTAGE)

NG

20.INSPECT CRANKSHAFT POSITION SENSOR
14.INSPECT ECM (VPA AND VPA2 TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.
A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
V-47 - V-45 Released 0.6 to 1.0 V
V-47 - V-45 Depressed 2.8 to 3.6 V
V-67 - V-65 Released 1.4 to 1.8 V
V-67 - V-65 Depressed 3.6 to 4.4 V



Result:
Proceed to
OK
NG



OK

15.INSPECT ECM (THA TERMINAL VOLTAGE)

NG

21.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
15.INSPECT ECM (THA TERMINAL VOLTAGE)
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405886C06
1.5,0.083 1.917,0.354 0.417,0.271 1.646,0.146 1.802,0.344 0.156,0.198 10 false M 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
E-47 - M-32 Idling, intake air temperature at 0 to 80°C (32 to 176°F) 0.5 to 3.4 V



Result:
Proceed to
OK
NG



OK

16.INSPECT ECM (THIA TERMINAL VOLTAGE)

NG

22.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
16.INSPECT ECM (THIA TERMINAL VOLTAGE)
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
E-63 - M-54 Idling, intake air temperature at 0 to 80°C (32 to 176°F) 1.0 to 4.4 V



Result:
Proceed to
OK
NG



OK

17.INSPECT ECM (PCR1 AND PCR2 TERMINAL VOLTAGE)

NG

23.INSPECT INTAKE AIR TEMPERATURE SENSOR (for Intake Manifold Side)
17.INSPECT ECM (PCR1 AND PCR2 TERMINAL VOLTAGE)
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Accelerator Pedal Condition Specified Condition
E-49 - E-56 Idling 1.3 to 1.7 V
E-68 - E-56 Idling 1.3 to 1.7 V



Result:
Proceed to
OK
NG



OK

NG

24.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
18.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.
A126612C04
1.573,2.844 1.313,3.198 1.313,3.198 1.313,3.333 false 0.635,1.688 0.813,1.833 0.177,0.146 10 false 30 0.635,1.875 0.813,2.021 0.177,0.146 10 false 20 0.635,2.177 0.813,2.323 0.177,0.146 10 false 10 0.729,2.49 0.823,2.635 0.094,0.146 10 false 5 0.729,3.146 0.823,3.292 0.094,0.146 10 false 1 2.417,2.948 2.604,3.115 0.188,0.167 10 false *1 1.198,3.375 1.396,3.542 0.198,0.167 10 false *a 0.729,2.906 0.823,3.052 0.094,0.146 10 false 2 0.729,2.708 0.823,2.854 0.094,0.146 10 false 3 0.583,3.604 0.802,3.75 0.219,0.146 10 false 0.3 0.583,3.417 0.802,3.563 0.219,0.146 10 false 0.5 0.583,3.948 0.802,4.094 0.219,0.146 10 false 0.1 0.583,3.76 0.802,3.906 0.219,0.146 10 false 0.2 0.885,4.021 1.104,4.167 0.219,0.146 10 false -20 1.281,4.021 1.375,4.177 0.094,0.156 10 false 0 1.542,4.021 1.719,4.167 0.177,0.146 10 false 20 1.885,4.021 2.063,4.167 0.177,0.146 10 false 40 2.219,4.021 2.396,4.167 0.177,0.146 10 false 80 2.594,4.021 2.896,4.167 0.302,0.146 10 false 100 0.875,4.188 1.115,4.365 0.24,0.177 10 false (-4) 1.167,4.188 1.438,4.365 0.271,0.177 10 false (32) 1.479,4.188 1.75,4.365 0.271,0.177 10 false (68) 1.781,4.188 2.125,4.365 0.344,0.177 10 false (104) 2.188,4.188 2.531,4.365 0.344,0.177 10 false (176) 2.594,4.188 2.938,4.365 0.344,0.177 10 false (212) 0.875,1.573 1.073,1.729 0.198,0.156 10 false kΩ 0.302,4.031 0.51,4.198 0.208,0.167 10 false °C 0.24,4.229 0.531,4.396 0.292,0.167 10 false (°F)
*1 Engine Coolant Temperature Sensor
*a Acceptable


Remove the engine coolant temperature sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 2.32 to 2.59 kΩ
80°C (176°F) 0.31 to 0.326 kΩ


NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed engine coolant temperature sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



c.

Reinstall the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

19.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A241069C41
0.427,1.125 0.854,1.385 0.427,0.26 0.958,1.76 1.375,1.344 true 1.635,1.844 1.656,1.344 true 2.229,1.74 1.854,1.344 true 0.531,1.177 0.99,1.375 0.458,0.198 10 false B18 0.25,0.188 0.708,0.385 0.458,0.198 10 false *a 0.854,1.781 1.313,1.979 0.458,0.198 10 false E 1.5,1.917 1.958,2.115 0.458,0.198 10 false PIM 2.271,1.76 2.729,1.958 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to air Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-51 - B18-3 (VC) Always Below 1 Ω
E-67 - B18-2 (PIM) Always Below 1 Ω
E-77 - B18-1 (E) Always Below 1 Ω
M-51 - Body ground and other terminals Always 10 kΩ or higher
E-67 - Body ground and other terminals Always 10 kΩ or higher
E-77 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

21.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the accelerator pedal assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-1 (VPA2) - V-67 Always Below 1 Ω
F9-2 (EPA2) - V-65 Always Below 1 Ω
F9-3 (EPA) - V-45 Always Below 1 Ω
F9-4 (VCPA) - V-50 Always Below 1 Ω
F9-5 (VPA) - V-47 Always Below 1 Ω
F9-1 (VPA2) or V-67 - Body ground Always 10 kΩ or higher
F9-2 (EPA2) or V-65 - Body ground Always 10 kΩ or higher
F9-3 (EPA) or V-45 - Body ground Always 10 kΩ or higher
F9-4 (VCPA) or V-50 - Body ground Always 10 kΩ or higher
F9-5 (VPA) or V-47 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter (intake air temperature sensor).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

NG

23.INSPECT INTAKE AIR TEMPERATURE SENSOR (for Intake Manifold Side)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)

NG

REPLACE INTAKE AIR TEMPERATURE SENSOR (for Intake Manifold Side)

24.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the common rail pressure assembly (fuel pressure sensor).

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>INSPECTION


Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

REPLACE COMMON RAIL ASSEMBLY

25.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B140-1 (VC1) - E-13 Always Below 1 Ω
B140-2 (PCR1) - E-49 Always Below 1 Ω
B140-2 (PCR1) - E-68 Always Below 1 Ω
B140-3 (E1) - E-56 Always Below 1 Ω
B140-1 (VC1) or E-13 - Body ground Always 10 kΩ or higher
B140-2 (PCR1) or E-49 - Body ground Always 10 kΩ or higher
B140-2 (PCR1) or E-68 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.REPLACE ECM
a.

Replace the ECM

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check the volume of black smoke in the exhaust gas.

OK:

Black smoke is not present.



Result:
Proceed to
OK
NG



OK

END

NG