The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the timing chain case assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
| Injector assembly (including shuffling the injector assemblies between the cylinders) | ·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly |
| Supply pump assembly | Fuel inlet pipe sub-assembly |
·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing chain case assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.
The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.
The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.
Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.
Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.
Make sure foreign matter does not enter the fuel path.
1.REMOVE ENGINE ASSEMBLY
12632
2.REMOVE NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)
82121
3.REMOVE ENGINE WIRE
26100G
4.REMOVE DIESEL THROTTLE BODY ASSEMBLY
16278
5.REMOVE NO. 2 WATER BY-PASS PIPE
89481B
6.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ DPF)
89425
7.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
25733A
8.REMOVE NO. 1 VACUUM PIPE (w/ DPF)
25734
9.REMOVE NO. 2 VACUUM PIPE (w/ DPF)
17578B
10.REMOVE PIPE CLAMP (w/ DPF)
12631A
11.REMOVE ENGINE COVER BRACKET
89421C
12.REMOVE DIESEL TURBO PRESSURE SENSOR
23265C
13.REMOVE GAS FILTER
25625
14.REMOVE EGR VALVE BRACKET
89425D
15.REMOVE NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
25612
16.REMOVE NO. 2 EGR PIPE
16206B
17.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)
16206B
18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)
27148A
19.REMOVE CONNECTING WIRE
25601
20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)
25601
21.REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)
25804
22.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)
16209
23.REMOVE NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
25800
24.REMOVE NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)
25.REMOVE EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)
25624
26.REMOVE EGR VALVE ADAPTER (w/o EGR System)
11409
27.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23812D
28.REMOVE NO. 2 FUEL PIPE
29.REMOVE WIRING HARNESS CLAMP BRACKET
17118
30.REMOVE MANIFOLD STAY
22803
31.REMOVE FUEL INJECTION PUMP COVER SUB-ASSEMBLY
23243B
32.REMOVE FUEL PUMP MOTOR WIRE
23273H
33.REMOVE NO. 2 FUEL HOSE
23271H
34.REMOVE NO. 1 FUEL HOSE
23804D
35.REMOVE NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)
23804D
36.REMOVE NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)
23815D
37.REMOVE NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)
23804C
38.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
39.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
17111
40.REMOVE INTAKE MANIFOLD
41.REMOVE WIRING HARNESS CLAMP BRACKET
23811H
42.REMOVE NO. 1 FUEL PIPE (w/ DPF)
23760
43.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY
44.REMOVE WIRING HARNESS CLAMP BRACKET
23701
45.REMOVE NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY
44781
46.REMOVE HOSE BRACKET
88320
47.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
88431
48.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
16632B
49.REMOVE NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)
12229
50.REMOVE PCV PIPE (for Cold Area Specification Vehicles)
16282
51.REMOVE NO. 5 WATER BY-PASS HOSE (w/ DPF)
16281
52.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)
23295D
53.REMOVE NO. 1 INJECTOR HOLDER (w/ DPF)
89467B
54.REMOVE AIR FUEL RATIO SENSOR (w/o Exhaust Gas Temperature Sensor for EGR)
17167
55.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ DPF)
17167
56.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>REMOVAL
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REMOVAL
17271
57.REMOVE NO. 1 TURBO INSULATOR (w/ DPF)
17271
58.REMOVE NO. 1 TURBO INSULATOR (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>REMOVAL
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REMOVAL
89463C
59.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
60.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/ DPF)
61.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>REMOVAL
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REMOVAL
62.REMOVE EXHAUST PIPE SUPPORT STAY (w/ DPF)
63.REMOVE EXHAUST PIPE SUPPORT STAY (w/o DPF)
w/ EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>REMOVAL
w/o EGR Cooler:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REMOVAL
25051
64.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ EGR Cooler)
17291
65.REMOVE TURBINE OUTLET ELBOW (w/o EGR Cooler)
89463C
66.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
12261
67.REMOVE PCV HOSE (except Cold Area Specification Vehicles)
16279
68.REMOVE NO. 3 WATER BY-PASS PIPE
69.REMOVE WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)
16268
70.REMOVE NO. 1 WATER BY-PASS PIPE
16284
71.DISCONNECT NO. 1 AND NO. 2 TURBO WATER HOSE
87101
72.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
17293
73.REMOVE TURBOCHARGER STAY
15474
74.REMOVE TURBO OIL OUTLET PIPE
15407
75.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
17201
76.REMOVE TURBOCHARGER SUB-ASSEMBLY
16207
77.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
16304
78.REMOVE WATER OUTLET SUB-ASSEMBLY
16321
79.REMOVE WATER INLET
16331A
80.REMOVE THERMOSTAT
16603
81.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley sub-assembly from the generator bracket sub-assembly.
16620
82.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 3 bolts and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.
88451B
83.REMOVE VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)
13496
84.REMOVE CRANKSHAFT PULLEY COVER (for Automatic Transmission)
13407
85.REMOVE CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)
13471
86.REMOVE CRANKSHAFT PULLEY (for Automatic Transmission)
16575C
87.REMOVE NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)
12281A
88.REMOVE NO. 1 ENGINE HANGER
12501
89.REMOVE GENERATOR BRACKET SUB-ASSEMBLY
23670
90.REMOVE INJECTOR ASSEMBLY
23682
91.REMOVE NOZZLE HOLDER GASKET
11401G
92.REMOVE CAMSHAFT POSITION SENSOR
11201
93.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
|
Bolt |
|
Nut |
|
Nozzle Holder Clamp Seat |
Remove the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and cylinder head cover sub-assembly from the cylinder head sub-assembly.
| *1 | Cylinder Head Cover Gasket |
| *2 | No. 2 Cylinder Head Cover Gasket |
| *3 | Camshaft Bearing Cap Oil Hole Gasket |
Remove the cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets from the cylinder head cover sub-assembly.
89491
94.REMOVE ENGINE OIL LEVEL SENSOR
12101
95.REMOVE OIL PAN SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 23 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and cylinder block sub-assembly, cut off the applied sealer and remove the oil pan sub-assembly.
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.
Be careful not to damage the cylinder block sub-assembly flange.
16100
96.REMOVE ENGINE WATER PUMP ASSEMBLY
97.SET NO. 1 CYLINDER TO TDC/COMPRESSION
11324
98.REMOVE TIMING CHAIN COVER PLATE
22100
99.REMOVE SUPPLY PUMP ASSEMBLY
22815A
100.REMOVE INJECTION PUMP INSULATOR
11302
101.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 20 bolts from the timing chain cover sub-assembly.
Using a screwdriver wrapped in protective tape, remove the timing chain cover sub-assembly by prying the points in the illustration.
| *a | Protective Tape | - | - |
Do not damage the contacting surfaces of the timing chain cover sub-assembly and timing chain case assembly.
Remove the timing chain case gasket from the timing chain case assembly.
11303A
102.REMOVE FRONT CRANKSHAFT OIL SEAL
| *a | Protective Tape |
| *b | Wooden Block |
Using a screwdriver and wooden block, pull out the front crankshaft oil seal.
Do not damage the surface of the front crankshaft oil seal press fit hole.
103.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR
Using a dial indicator, measure the backlash.
0.02 to 0.3 mm (0.000787 to 0.0118 in.)
0.42 mm (0.0165 in.)
If the gear backlash is more than the maximum, replace the timing chain case assembly or oil pump drive gear.
13519
104.REMOVE OIL PUMP DRIVE GEAR
Remove the oil pump drive gear from the crankshaft.
13560A
105.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
11991A
106.REMOVE NO. 1 BALANCESHAFT THRUST PLATE
107.REMOVE BALANCESHAFT TIMING SPROCKET, BALANCESHAFT GEAR SUB-ASSEMBLY WITH NO. 3 CHAIN SUB-ASSEMBLY
13566B
108.REMOVE TIMING CHAIN GUIDE
13550
109.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
110.REMOVE NO. 2 CHAIN TENSIONER SLIPPER
13562
111.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13507
112.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
13540
113.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13559
114.REMOVE NO. 1 CHAIN TENSIONER SLIPPER
13561
115.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13506
116.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY
13523
117.REMOVE CAMSHAFT TIMING SPROCKET
11310
118.REMOVE TIMING CHAIN CASE ASSEMBLY
Remove the 15 bolts from the timing chain case assembly.
Using a screwdriver wrapped in protective tape, remove the timing chain case assembly by prying the points in the illustration.
| *a | Protective Tape | - | - |
Do not damage the contacting surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.
Remove the 4 O-rings from the cylinder head sub-assembly and cylinder block sub-assembly.
Remove the gasket from the timing chain case assembly.