When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal*1 or clutch pedal*2 depressed.
*1: for Automatic Transmission
*2: for Manual Transmission
When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Engine does not start | Power Source Control
·
Stop Light Switch1 ·
Steering Unlock Switch ·
Power Supply Condition ·
IG Relay Monitor(Inside) ·
IG Relay Monitor(Outside) ·
Latch Circuit ·
Shift P Signal* ·
Neutral SW/ Clutch SW ·
Starter Request Signal Entry&Start
·
Immobiliser ·
S Code Check ·
L Code Check ·
Engine Start Request Starting Control
·
Ignition ·
Starter SW ·
Shift Position P or N* |
- |
*: for Automatic Transmission
Refer to "System Diagram" (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>SYSTEM DIAGRAM)
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:
Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).
Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly), ECM or ID code box (immobiliser code ECU), refer to the entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.
After completing repairs, confirm that the problem does not occur.
If the brake pedal*1 or clutch pedal*2 is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal*1 or clutch pedal*2 to illuminate the stop lights increases.
*1: for Automatic Transmission
*2: for Manual Transmission
Press a switch of the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly LED illuminates.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Key Low Battery | Transmitter battery depleted/Yes or No | Yes: Transmitter battery depleted
No: Transmitter battery not depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
"No" is displayed in the Data List.
OK
NG
If the problem occurs in certain locations or times of day, the possibility of wave interference is high.
Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver.
Engine starts.
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
for Automatic Transmission:
Move the shift lever to P.
With the brake pedal released*1 or clutch pedal*2, check that pressing the engine switch causes the power source mode to change.
*1: for Automatic Transmission
*2: for Manual Transmission
| Result | Proceed to |
|---|---|
| Off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (ACC) and on (IG) | B |
| Power source mode changes to on (IG) but not to on (ACC) | C |
| Power source mode changes to on (ACC) but not to on (IG) | D |
A
B
C
D
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Neutral SW/ Clutch SW | for Automatic Transmission:
Shift position (P and N)/ON or OFF for Manual Transmission:
State of clutch pedal/ON or OFF |
for Automatic Transmission:
ON: Shift lever in P or N OFF: Shift lever in any position other than P or N for Manual Transmission:
ON: Clutch pedal depressed OFF: Clutch pedal released |
for Automatic Transmission:
·
Use this item to determine whether the park/neutral position switch is malfunctioning. ·
When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed. for Manual Transmission:
·
Use this item to help determine if the clutch position switch is malfunctioning . ·
The engine cannot be started when this item is "OFF". |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift Position P or N | Park/neutral position switch status/ON or OFF | ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N |
When malfunctioning, the engine will not crank. |
The item in the Data List changes according to the shift position.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for Automatic Transmission | B |
| for Manual Transmission | C | |
A
B
C
Using the GTS, check for DTCs.
| Result | Proceed to | |
|---|---|---|
| DTCs are not output | for Automatic Transmission | A |
| for Manual Transmission | B | |
| Entry and start system (for Start Function) DTCs are output | C | |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light Switch1 | State of brake pedal/ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is OFF. ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
The item in the Data List changes when the brake pedal is depressed and released.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Starter Request Signal | Engine start request signal status/ON or OFF | for Automatic Transmission:
ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held OFF: After approximately 1 second. has elapsed, the engine switch is released for Manual Transmission:
ON: With the clutch pedal depressed, the engine switch is pressed and held OFF: After approximately 1 second has elapsed, the engine switch is released |
·
When the engine cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time. |
Check that the key warning light is displayed on the multi-information display on the combination meter assembly, and then press the engine switch.
The display changes in response to the operation of the engine switch.
OK
NG
Check that the steering unlocks when the engine switch is turned on (ACC).
The steering unlocks.
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
for Automatic Transmission:
Move the shift lever to P.
Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
*1: for Automatic Transmission
*2: for Manual Transmission
It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
OK
NG
Inspect the transmitter battery.
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
OK
NG
Remove the park/neutral position switch assembly.
Inspect the park/neutral position switch assembly.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for AB60F | B |
| for A750F | C | |
| for AE80F | D | |
A
B
(See pageDrivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
C
(See pageDrivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
D
(See pageDrivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the C45*1 or C46*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Disconnect the C24 park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - C24-3 (B) | Always | Below 1 Ω |
| E128-10 (STAR) or C24-3 (B) - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - C24-4 (B) | Always | Below 1 Ω |
| E128-10 (STAR) or C24-4 (B) - Body ground | 10 kΩ or higher |
OK
NG
Remove the clutch start switch assembly.
for RHD: See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>REMOVAL.
for LHD: See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>REMOVAL.
Inspect the clutch start switch assembly.
for RHD: See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION.
for LHD: See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for RHD | B |
| for LHD | C | |
A
B
C
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the e1*1 or A49*2 clutch start switch assembly connector.
*1: for RHD
*2: for LHD
Disconnect the C45*1 or C46*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - e1-1 | Always | Below 1 Ω |
| E128-10 (STAR) or e1-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - A49-1 | Always | Below 1 Ω |
| E128-10 (STAR) or A49-1 - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the A38*1 or A52*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Disconnect the A24 skid control ECU (brake actuator assembly) connector.
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the A73 stop light switch assembly connector.
Disconnect the E51 shift lock control ECU connector.
Disconnect the A39 stop light control relay assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-1 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-2 (STP1) - A73-2 (L) | Always | Below 1 Ω |
| E128-2 (STP1) or A73-2 (L) - Body ground | 10 kΩ or higher | |
| A73-3 (GND) - Body ground | Below 1 Ω |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
OK
NG
Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Starting Control / Data List.
Get into the vehicle while carrying an electrical key transmitter sub-assembly and press the engine switch with the shift lever in P and brake pedal depressed to check if the Data List display changes.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Starter SW | Starter operation request/ON or OFF | ON: Starter operation requested
OFF: Starter operation not requested |
When malfunctioning, the engine will not crank. |
The Data List item changes.
OK
NG
Remove the ST relay.
Inspect the ST relay.
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (STARTING)>RELAY>ON-VEHICLE INSPECTION.
for 1GR-FE: See page Engine / Hybrid System>1GR-FE (STARTING)>RELAY>ON-VEHICLE INSPECTION.
for 3UR-FE: See page Engine / Hybrid System>3UR-FE (STARTING)>RELAY>ON-VEHICLE INSPECTION.
for 1VD-FTV: See page Engine / Hybrid System>1VD-FTV (STARTING)>RELAY>ON-VEHICLE INSPECTION.
OK
NG
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the A38 and C45*1 or A52 and C46*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
for Automatic Transmission:
Move the shift lever to P or N.
for Manual Transmission:
Depress the clutch pedal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - Body ground | 20°C (68°F) | 93.75 to 136.36 Ω |
| E128-12 (STA) - Body ground |
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for Automatic Transmission | B |
| for Manual Transmission | C | |
A
B
C
Remove the starter assembly.
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (STARTING)>STARTER>REMOVAL.
for 3UR-FE: See page Engine / Hybrid System>3UR-FE (STARTING)>STARTER>REMOVAL
for 1VD-FTV: See page Engine / Hybrid System>1VD-FTV (STARTING)>STARTER>REMOVAL.
Inspect the starter assembly .
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (STARTING)>STARTER>INSPECTION.
for 1GR-FE: See page Engine / Hybrid System>1GR-FE (STARTING)>STARTER>INSPECTION.
for 3UR-FE: See page Engine / Hybrid System>3UR-FE (STARTING)>STARTER>INSPECTION.
for 1VD-FTV: See page Engine / Hybrid System>1VD-FTV (STARTING)>STARTER>INSPECTION.
| Result | Proceed to | |
|---|---|---|
| OK | A | |
| NG | for 1UR-FE | B |
| for 1GR-FE | C | |
| for 3UR-FE | D | |
| for 1VD-FTV | E | |
A
B
C
D
E
Remove the starter assembly from the vehicle to perform an inspection.
for 1UR-FE: See page Engine / Hybrid System>1UR-FE (STARTING)>STARTER>REMOVAL.
for 1GR-FE: See page Engine / Hybrid System>1GR-FE (STARTING)>STARTER>REMOVAL.
for 3UR-FE: See page Engine / Hybrid System>3UR-FE (STARTING)>STARTER>REMOVAL.
for 1VD-FTV: See page Engine / Hybrid System>1VD-FTV (STARTING)>STARTER>REMOVAL.
Remove the ST relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D16-1 - Body ground | Always | 11 to 14 V |
| ST relay terminal 5 - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D21-1 - Body ground | Always | 11 to 14 V |
| ST relay terminal 5 - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D20-1 - Body ground | Always | 11 to 14 V |
| ST relay terminal 5 - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D13-1 - Body ground | Always | 11 to 14 V |
| ST relay terminal 5 - Body ground |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 3 - D12-1 | Always | Below 1 Ω |
| ST relay terminal 3 or D12-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 3 - D2-1 | Always | Below 1 Ω |
| ST relay terminal 3 or D2-1 - Body ground | 10 kΩ or higher |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the C24 park/neutral position switch connector.
Disconnect the C45*1 or C46*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - C24-3 (B) | Always | Below 1 Ω |
| E128-10 (STAR) or C24-3 (B) - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - C24-4 (B) | Always | Below 1 Ω |
| E128-10 (STAR) or C24-4 (B) - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the C24 park/neutral position switch connector.
Remove the ST relay.
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the A38*1 or A52*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-8 (L) - ST relay terminal 2 | Always | Below 1 Ω |
| C24-8 (L) or ST relay terminal 2 - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-5 (L) - ST relay terminal 2 | Always | Below 1 Ω |
| C24-5 (L) or ST relay terminal 2 - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Remove the ST relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-12 (STA) - ST relay terminal 2 | Always | Below 1 Ω |
| E128-12 (STA) or ST relay terminal 2 - Body ground | 10 kΩ or higher |
OK
NG
Remove the ST relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 1 - Body ground | Always | Below 1 Ω |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the e1*1 or A49*2 clutch start switch assembly connector.
*1: for RHD
*2: for LHD
Disconnect the C45*1 or C46*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - e1-1 | Always | Below 1 Ω |
| E128-10 (STAR) or e1-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-10 (STAR) - A49-1 | Always | Below 1 Ω |
| E128-10 (STAR) or A49-1 - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the e1*1 or A49*2 clutch start switch assembly connector.
*1: for RHD
*2: for LHD
Remove the ST relay.
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Disconnect the A38*1 or A52*2 ECM connector.
*1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE
*2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e1-2 - ST relay terminal 2 | Always | Below 1 Ω |
| e1-2 or ST relay terminal 2 - Body ground | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-2 - ST relay terminal 2 | Always | Below 1 Ω |
| A49-2 or ST relay terminal 2 - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the E128 certification ECU (smart key ECU assembly) connector.
Remove the ST relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-12 (STA) - ST relay terminal 2 | Always | Below 1 Ω |
| E128-12 (STA) or ST relay terminal 2 - Body ground | 10 kΩ or higher |
OK
NG
Remove the ST relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 1 - Body ground | Always | Below 1 Ω |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG