Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2020.11–2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P300449  High Voltage Power Resource Circuit Short during Pre-Charge  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU monitors the high-voltage wiring between the EV supply battery assembly and inverter with converter assembly and detects an open circuit malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction
·

Voltage sensor (VH) malfunction

·

Motor generator control ECU (MG ECU) malfunction

·

Communication (wire harness) malfunction


High voltage system malfunction
·

EV supply battery assembly malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Inverter with converter assembly malfunction

·

High-voltage wire harness malfunction

·

High-voltage connector or connection malfunction


Low-voltage circuit (12 V) malfunction
·

EV control ECU malfunction

·

No. 1 EV battery junction block assembly malfunction

·

Low voltage wire harness malfunction

·

Low voltage connector malfunction



DESCRIPTION

Refer to the description for DTC P0AE411.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411

The EV control ECU monitors the high-voltage wiring between the EV supply battery assembly and the inverter with converter assembly and detects the malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P300449 High Voltage Power Resource Circuit Short during Pre-Charge Although a system main relay operation signal was sent when the ignition switch was operated, the system voltage is not sufficiently increased after boosting and the EV supply battery assembly current does not flow.
High-voltage circuit malfunctions between the EV supply battery assembly and inverter with converter assembly.
The EV fuse is blown, the service plug grip is removed, the system main resistor is blown, SMRP or SMRB remains open, or the high-voltage cable has an open circuit.
(2 trip detection logic)
·

No. 1 EV battery junction block assembly

·

Floor under wire

·

Inverter with converter assembly

·

No. 1 EV supply stack sub-assembly

·

No. 2 EV supply stack sub-assembly

·

EV battery terminal block

·

FC junction cable

·

FC inverter input terminal

·

Wire harness or connector


Master Warning:
Comes on
EV A

Related Data List
DTC No. Data List
P300449
·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting



The following items can be helpful when performing repairs:

Data List
·

Ready Signal

·

Inter Lock Switch

·

SMRP Status

·

SMRB Status

·

SMRG Status


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 10 minutes or more.

3.

Turn the ignition switch to ON (READY) and wait for 3 minutes or more.

HINT:

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.


4.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>HV Battery High-voltage Line Circuit

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C04
0.552,4.156 0.865,4.354 0.313,0.198 10 false *a 2.76,4.167 3.073,4.365 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an EV supply battery assembly, make sure to return it through an authorized collection agent who is capable of handling it safely. If the EV supply battery assembly is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the EV supply battery assembly or the EV supply stack sub-assembly is disposed of improperly or abandoned.

Therefore, make sure to return EV supply battery assembly and all EV supply stack sub-assemblies through an authorized collection agent.


·

Before returning the EV supply battery assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the EV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the EV supply battery assembly and EV supply stack sub-assemblies.

·
A358020

After removing the EV supply battery assembly or the EV supply stack sub-assembly, keep it away from water. Exposure to water may cause the EV supply battery assembly or the EV supply stack sub-assembly to produce heat, resulting in a fire.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV, EV BATTERY, FCDC)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Powertrain > EV Battery > Trouble Codes
50001 398
Powertrain > FCDC > Trouble Codes
50001 493
Result:
Result Proceed to
P300449 only is output, or DTCs except the ones in the table below are also output A
Any hybrid control system DTCs in the table below are output B
Any hybrid battery system DTCs in the table below are output C
Any FC control system DTCs in the table below are output D


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P0A1B49 Drive Motor "A" Control Module Internal Electronic Failure
P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P1C9E9F Hybrid/EV System Reset Stuck Off
P0A1B1F Drive Motor "A" Control Module Circuit Intermittent
P1C2B00 Drive Motor "A" Control Module A/D Processing Performance
P1CA700 Drive Motor "A" Control Module RAM/ROM Error
P1D0400 FC Air Compressor Motor Control Module A/D Processing Performance
P1D0500 FC Air Compressor Motor Control Module RAM/ROM Error
P1D8F47 FC Air Compressor Motor Control Module Watchdog/Safety MCU Failure
P1D8F49 FC Air Compressor Motor Control Module Internal Electronic Failure
P1E3B87 Communication Error from FC Air Compressor Motor to Drive Motor "A" Missing Message
Hybrid battery system P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B16 Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold
P0E2D00 Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance
Power source circuit malfunction Hybrid control system P06D61C Sensor Reference Voltage "F" Circuit/Open Circuit Voltage Out of Range
P06E61C Sensor Power Supply "C" Circuit/Open Circuit Voltage Out of Range
Communication system malfunction Hybrid control system P312387 Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message
U011187 Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message
Sensor and actuator circuit malfunction Hybrid control system P0AD915 Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open
P0AD911 Hybrid/EV Battery Positive Contactor Circuit Short to Ground
P0AE415 Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open
P0AE411 Hybrid/EV Battery Precharge Contactor Circuit Short to Ground
P0ADD15 Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open
P0ADD11 Hybrid/EV Battery Negative Contactor Circuit Short to Ground
P0B231C Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range
P0ABF00 Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance
FC control system P1E9011 FC Positive Contactor Control Circuit Short to Ground
P1E9015 FC Positive Contactor Control Circuit Short to Battery or Open
P1E9211 FC Precharge Contactor Control Circuit Short to Ground
P1E9215 FC Precharge Contactor Control Circuit Short to Battery or Open
P1E9111 FC Negative Contactor Control Circuit Short to Ground
P1E9115 FC Negative Contactor Control Circuit Short to Battery or Open
Hybrid battery system P0ABF11 Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground
P0B0E11 Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground
P0B0E15 Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open
P0ABF15 Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range
P1AFD1C Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure
P0ABF2A Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range
P1CBB12 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery
P1CBB14 Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open
P0B1362 Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure
System malfunction Hybrid control system P0C7600 Hybrid/EV Battery System Discharge Time Too Long
P0D2D1C Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range
P1C8149 High Voltage Power Resource Circuit Consumption Circuit Short
P1C8249 High Voltage Power Resource Circuit Over Loading
P1C8349 High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction
P0D2D16 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Below Threshold
P0D2D17 Drive Motor "A" Inverter Voltage Sensor "A" Circuit Voltage Above Threshold
P1CB69E Drive Motor "A" Inverter Overvoltage Signal Stuck On
P0CA300 DC/DC Converter Step Up Voltage Performance
Hybrid battery system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation

HINT:
·

P300449 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

a.

Turn the ignition switch off.



A

2.CHECK FREEZE FRAME DATA (EV)

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

D

2.CHECK FREEZE FRAME DATA (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Read the freeze frame data of DTC P300449.

Powertrain > EV
Tester Display Measurement Item Range
VL-Voltage before Boosting High voltage before it is boosted -
VH-Voltage after Boosting High voltage after it is boosted -
Hybrid/EV Battery Voltage EV battery voltage 0.00 to 1023.98 V
Powertrain > EV > DTC(P300449) > Freeze Frame Data
Tester Display
VL-Voltage before Boosting
VH-Voltage after Boosting
Hybrid/EV Battery Voltage
50040 397 150,151,227 P300449
Result:
Result Proceed to
Both of the following conditions are met:
·

"VH-Voltage after Boosting" is below 50 V.

·

Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 28 V or less.


A
Except above B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014

Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

OK (for RHD)

4.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 FLOOR WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (NO. 2 EV BATTERY PACK WIRE CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

OK

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)

NG

CONNECT SECURELY

7.CHECK HARNESS AND CONNECTOR (EV CONTROL ECU - NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 10 EV battery shield panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A478500E02
2.01,0.375 2.365,0.677 0.354,0.302 2.094,0.458 2.333,0.604 0.24,0.146 10 true z24

Disconnect the z24 No. 1 EV battery junction block assembly connector.


d.

Disconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


Procedure1

a.
A479459C39
2.552,3.5 3.01,3.865 0.458,0.365 0.896,1.542 1.292,1.854 0.396,0.313 0.896,1.969 1.292,2.281 0.396,0.313 1.042,4.24 1.375,3.823 true 0.76,2.573 0.458,1.75 true 0.24,2.365 0.385,1.813 true 1.917,4.24 1.625,3.823 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.198,2.76 0.51,2.958 0.313,0.198 10 false *b 2.688,3.615 3,3.813 0.313,0.198 10 false z24 0.823,4.302 1.333,4.49 0.51,0.188 10 false SMRB 0.979,1.615 1.521,1.802 0.542,0.188 10 false G14 0.594,2.615 1.052,2.781 0.458,0.167 10 false SMRB 0.063,2.427 0.521,2.594 0.458,0.167 10 false SMRP 1.927,4.292 2.479,4.49 0.552,0.198 10 false SMRP 0.979,2.031 1.521,2.219 0.542,0.188 10 false A14 1.323,1.625 1.865,1.813 0.542,0.188 10 false *A 1.354,2.031 1.896,2.219 0.542,0.188 10 false *B
*A for LHD
*B for RHD
*a Rear view of wire harness connector
(to EV Control ECU)
*b Front view of wire harness connector
(to No. 1 EV Battery Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition

Click Location & Routing(G14,z24)Location & Routing

Click Connector(G14)Instrument Panel>Floor Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

G14-4 (SMRB) - z24-1 (SMRB) Ignition switch off Below 1 Ω
G14-14 (SMRP) - z24-2 (SMRP) Ignition switch off Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition

Click Location & Routing(A14,z24)Location & Routing

Click Connector(A14)Instrument Panel>Front Compartment Main Wire>EV Control ECU

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

A14-4 (SMRB) - z24-1 (SMRB) Ignition switch off Below 1 Ω
A14-14 (SMRP) - z24-2 (SMRP) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the G14*1 or A14*2 EV control ECU connector.

*1: for LHD

*2: for RHD


b.

Reconnect the z24 No. 1 EV battery junction block assembly connector.


c.

Install the No. 10 EV battery shield panel.



OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

OK

9.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery junction block assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479455C06
3.208,0.188 3.583,0.417 0.375,0.229 3.802,1 4.177,1.271 0.375,0.271 5.656,0.115 6.042,0.396 0.385,0.281 3.354,0.688 3.052,1 true 3.156,1.427 3.396,1.188 true 3.813,1.427 3.604,1.177 true 6.333,1.094 5.813,0.688 true 0.198,0.146 0.51,0.302 0.313,0.156 10 false *a 3.344,0.24 3.552,0.396 0.208,0.156 10 true N1 2.823,1.031 3.135,1.188 0.313,0.156 10 true CBI 2.917,1.438 3.26,1.625 0.344,0.188 10 true GND 3.677,1.438 4.146,1.635 0.469,0.198 10 true SMRB 3.885,1.052 4.135,1.208 0.25,0.156 10 false z24 5.75,0.188 6.01,0.354 0.26,0.167 10 true z13 6.385,1.073 6.635,1.229 0.25,0.156 10 false +
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z13,N1)Location & Routing

Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(N1)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

z13-1 (+) - N1-1 (CBI) Auxiliary battery voltage applied between terminals z24-1 (SMRB) and z24-3 (GND) Below 1 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z24)Location & Routing

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z24-1 (SMRB) - z24-3 (GND) -40 to 80°C (-40 to 176°F) 25.0 to 59.0 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 EV battery junction block assembly.



OK

10.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

NG

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

10.INSPECT NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 EV battery junction block assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL



Procedure1

a.

Measure the resistance according to the value(s) in the table below.

A479455C07
1.177,0.115 1.552,0.396 0.375,0.281 3.802,0.979 4.177,1.25 0.375,0.271 2.25,0.115 2.604,0.385 0.354,0.271 2.396,0.688 2.115,1.052 true 3.115,1.396 3.396,1.177 true 3.76,1.365 3.51,1.188 true 0.802,1.01 1.313,0.667 true 0.198,0.146 0.51,0.302 0.313,0.156 10 false *a 1.26,0.188 1.51,0.365 0.25,0.177 10 true z12 1.917,1.073 2.198,1.229 0.281,0.156 10 true CEI 2.917,1.438 3.281,1.646 0.365,0.208 10 true GND 3.688,1.396 4.177,1.583 0.49,0.188 10 true SMRP 3.896,1.031 4.146,1.188 0.25,0.156 10 false z24 0.729,0.99 0.979,1.146 0.25,0.156 10 false - 2.354,0.188 2.552,0.354 0.198,0.167 10 true N2
*a Component without harness connected
(No. 1 EV Battery Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z12,N2)Location & Routing

Click Connector(z12)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(N2)Body>Floor Under Wire>No. 1 EV Battery Junction Block Assembly

z12-1 (-) - N2-1 (CEI) Auxiliary battery voltage applied between terminals z24-2 (SMRP) and z24-3 (GND) 24.3 to 29.7 Ω



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(z24)Location & Routing

Click Connector(z24)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

z24-2 (SMRP) - z24-3 (GND) -40 to 80°C (-40 to 176°F) 140 to 290 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the No. 1 EV battery junction block assembly.



OK

11.CHECK INVERTER WITH CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)

NG

REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

11.CHECK INVERTER WITH CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A483165C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.458 0.313,2.656 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Check that the bolts for the FC junction cable is tightened to the specified torque, the FC junction cable is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.

Disconnect the FC junction cable from the inverter with converter assembly.


Procedure1

a.

Check for arc marks on the terminals for the FC junction cable and inverter with converter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the FC junction cable.



A

12.CHECK FC CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

12.CHECK FC CONVERTER ASSEMBLY (FC JUNCTION CABLE CONNECTION CONDITION)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Check that the bolts for the FC junction cable is tightened to the specified torque, the FC junction cable is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)



c.

Disconnect the FC junction cable from the FC converter assembly.


Procedure1

a.

Check for arc marks on the terminals for the FC junction cable and FC converter assembly.

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



Post-procedure1

a.

Reconnect the FC junction cable.



A

13.CHECK FC JUNCTION CABLE (FC CONVERTER ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

13.CHECK FC JUNCTION CABLE (FC CONVERTER ASSEMBLY - INVERTER WITH CONVERTER ASSEMBLY)

OK

14.CHECK FC CONVERTER ASSEMBLY

NG

REPLACE FC JUNCTION CABLE

14.CHECK FC CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A484669C01
0,0 0.313,0.198 0.313,0.198 10 true *A 0,2.479 0.313,2.677 0.313,0.198 10 true *B
*A for LHD
*B for RHD


Disconnect the floor under wire from the FC converter assembly.


c.
A484671C01
0,2.438 0.313,2.635 0.313,0.198 10 true *B 0,0 0.313,0.198 0.313,0.198 10 true *A
*A for LHD
*B for RHD


Disconnect the FC junction cable from the FC converter assembly.


Procedure1

a.
A481475C02
0.99,0.438 1.406,0.75 0.417,0.313 1.927,0.438 2.344,0.75 0.417,0.313 1.292,1.146 1.49,1.667 true 2.01,1.188 1.896,1.75 true 1.135,1.156 0.865,1.646 true 2.188,1.156 2.406,1.708 true 2.063,0.531 2.281,0.698 0.219,0.167 10 true x2 1.125,0.542 1.354,0.698 0.229,0.156 10 true N3 0.677,1.688 0.958,1.865 0.281,0.177 10 true CBI 1.417,1.688 1.708,1.875 0.292,0.188 10 true CEI 1.833,1.75 2.01,1.958 0.177,0.208 10 true N 2.396,1.74 2.542,1.906 0.146,0.167 10 true P 0.063,0.042 0.292,0.198 0.229,0.156 10 true *a
*a Component without harness connected
(FC Converter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

Click Location & Routing(N3,x2)Location & Routing

Click Connector(N3)Engine Compartment>Floor Under Wire>FC Converter Assembly

Click Connector(x2)Engine Compartment>FC Junction Cable>FC Converter Assembly

N3-1 (CEI) - x2-2 (N) Ignition switch off Below 1 Ω
N3-2 (CBI) - x2-1 (P) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the FC junction cable.


b.

Reconnect the floor under wire.



OK

15.CHECK FC CONVERTER ASSEMBLY (FLOOR UNDER WIRE CONNECTION CONDITION)

NG

27.REMOVE FC CONVERTER ASSEMBLY
15.CHECK FC CONVERTER ASSEMBLY (FLOOR UNDER WIRE CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C8349

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

16.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (FLOOR UNDER WIRE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

16.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (FLOOR UNDER WIRE CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C8349

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

17.CHECK FLOOR UNDER WIRE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

17.CHECK FLOOR UNDER WIRE

OK

18.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (EV SUPPLY BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

NG

18.CHECK NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY (EV SUPPLY BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C8349

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

19.CHECK EV BATTERY TERMINAL BLOCK (EV SUPPLY BATTERY ASSEMBLY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

19.CHECK EV BATTERY TERMINAL BLOCK (EV SUPPLY BATTERY ASSEMBLY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P1C8349

Result:
Result Proceed to
The terminals are connected securely and there are no contact problems. There are no arc marks. A
The terminals are not connected securely and there is a contact problem. There are arc marks. B
The terminals are not connected securely and there is a contact problem. There are no arc marks. C
The terminals are connected securely and there are no contact problems. There are arc marks. B



A

20.CHECK EV BATTERY TERMINAL BLOCK

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

20.CHECK EV BATTERY TERMINAL BLOCK

OK

21.CHECK NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE EV BATTERY TERMINAL BLOCK

21.CHECK NO. 1 EV SUPPLY STACK SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
C371880

Disconnect the EV supply battery high voltage connector from the EV battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C386915C05
1.49,0.344 1.948,0.688 0.458,0.344 1.667,3.406 2.25,2.969 true 1.823,1.563 2.083,1.99 true 0.208,0.24 0.521,0.396 0.313,0.156 10 false *a 0.219,2.146 0.531,2.302 0.313,0.156 10 true *b 1.625,0.427 1.948,0.604 0.323,0.177 10 false z18 2.292,2.833 2.49,3.021 0.198,0.188 10 true 1 2.073,2 2.396,2.177 0.323,0.177 10 false +
*a No. 1 EV Supply Stack Sub-assembly Connector
(EV Battery Terminal Block Side)
*b No. 1 EV Supply Stack Sub-assembly Connector
(Service Plug Grip Side)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z18)Location & Routing

Click Connector(z18)Body>other>EV Supply Battery Assembly , EV Battery Terminal Block

z18-1 (+) - 1 Ignition switch off 50 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the upper EV battery cover panel.



OK

22.CHECK NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

NG

REPLACE NO. 1 EV SUPPLY STACK SUB-ASSEMBLY

22.CHECK NO. 2 EV SUPPLY STACK SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the upper EV battery cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>REMOVAL



c.
A479456E01
2.333,0.104 2.792,0.438 0.458,0.333 2.469,0.208 2.927,0.406 0.458,0.198 10 false z13

Disconnect the EV supply battery high voltage connector from the No. 1 EV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



d.
C371879

Disconnect the EV supply battery high voltage connector from the EV battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

a.
C371903C04
1.042,0.385 1.479,0.708 0.438,0.323 1.531,2.396 1.969,2.719 0.438,0.323 0.917,2.021 1.229,1.521 true 1.385,4.094 1.698,3.594 true 0.229,0.177 0.542,0.333 0.313,0.156 10 false *a 0.313,2.49 0.625,2.646 0.313,0.156 10 false *b 0.813,2.031 0.969,2.229 0.156,0.198 10 false + 1.177,0.49 1.49,0.688 0.313,0.198 10 false z13 1.656,2.49 1.969,2.688 0.313,0.198 10 false z19 1.281,4.063 1.438,4.26 0.156,0.198 10 false -
*a No. 2 EV Supply Stack Sub-assembly Connector
(No. 1 EV Battery Junction Block Assembly Side)
*b No. 2 EV Supply Stack Sub-assembly Connector
(EV Battery Terminal Block Side)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(z13,z19)Location & Routing

Click Connector(z13)Body>other>EV Supply Battery Assembly , No. 1 EV Battery Junction Block Assembly

Click Connector(z19)Body>other>EV Supply Battery Assembly , EV Battery Terminal Block

z13-1 (+) - z19-1 (-) Ignition switch off 50 V or higher


CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the 2 EV supply battery high voltage connectors.


b.

Install the upper EV battery cover panel.



OK

23.CHECK FOR INTERMITTENT PROBLEMS

NG

REPLACE NO. 2 EV SUPPLY STACK SUB-ASSEMBLY

23.CHECK FOR INTERMITTENT PROBLEMS
HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Result:
Result Proceed to
Problem symptom does not recur. A
Problem symptom recurs. B


HINT:
·

Since 2 trip detection logic is used, the DTC detection condition must be met twice.

·

If DTC P300449 is output again after performing the inspection, replace the inverter with converter assembly. If DTC P300449 is not output again, replace the No. 1 EV battery junction block assembly.




A

24.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

24.REPLACE NO. 1 EV BATTERY JUNCTION BLOCK ASSEMBLY

NEXT

25.CLEAR DTC
25.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > EV > Clear DTCs
50002 397
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off and wait for 10 minutes or more.



NEXT

26.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)
26.CHECK EV CONTROL ECU (CHECK FOR NORMAL OPERATION)

Pre-procedure1

a.

Turn the ignition switch to ON (READY).


Procedure1

a.

According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.

Powertrain > EV > Data List
Tester Display
VL-Voltage before Boosting
Hybrid/EV Battery Voltage
50003 397 150,227
Result:
Result Proceed to
Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. A
Except above B



Post-procedure1

a.

None.



A

END

B

27.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

REPLACE FC INVERTER INPUT TERMINAL