10I Engine Auto Stop Start System
Precautions
- Precautions for Diagnosing Trouble
- Precautions for Servicing ENG A-STOP System
- Precautions for Replacing ENG A-STOP Control Module
General Description
- ENG A-STOP System Description
- Description of ENG A-STOP System Components
- Description of ENG A-STOP System Alarm Function
- CAN Communication System Description
Schematic and Routing Diagram
Component Location
Diagnostic Information and Procedures
- ENG A-STOP System Check
- ENG A-STOP Control Module Self-Diagnosis Function
- DTC Check
- DTC Clearance
- DTC Table
- Fail-Safe Table
- Scan Tool Data
- Scan Tool Active Test Table
- ENG A-STOP System Symptom Diagnosis
- ENG A-STOP Warning Light Does Not Come ON with Ignition “ON” and Engine Stopped (but Engine Can Be Started)
- ENG A-STOP Warning Light Remains ON or Blinking with Ignition “ON”
- DTC C1372 / C1373 Invalid Data Received From ENG A-STOP Control Module to ABS / ESP® Control Module
- DTC P0555 Brake Booster Pressure Sensor Circuit
- DTC P0602 Control Module Programming Error
- DTC P081D Neutral Input Circuit
- DTC P083F Clutch Pedal Switch “A” / “B” Correlation
- DTC P1300 ENG A-STOP Control Module Performance; P1305 Internal Control Module Memory Check Sum Error
- DTC P1302 ENG A-STOP Control Module Power Input Signal Low
- DTC P1303 ENG A-STOP Control Module Power Input Signal High
- DTC P1311 ENG A-STOP Starter Relay Circuit Low; P1312 ENG A-STOP Starter Relay Circuit High
- DTC P1313 ENG A-STOP Starter Performance
- DTC P1314 ENG A-STOP Starter Active Counter Not Set
- DTC P1321 ENG A-STOP Battery Current Sensor “A” Circuit Low; P1322 ENG A-STOP Battery Current Sensor “A” Circuit High
- DTC P1326 ENG A-STOP Battery Temperature Sensor Circuit Low; P1327 ENG A-STOP Battery Temperature Sensor Circuit High
- DTC P1335 ENG A-STOP DC-DC Converter “B” Performance; P1358 ENG A-STOP DC-DC Converter “B” Output Circuit Short to Ground
- DTC P1336 / P1337 / P1338 ENG A-STOP DC-DC Converter “B” Enable Circuit / Open / Low / High
- DTC P133A Internal DC/DC Converter Voltage Low; P133B Internal DC/DC Converter Voltage High
- DTC P1340 ENG A-STOP ECM Sequence Counter Incorrect; P1341 Invalid Data Received From ENG A-STOP Control Module to ECM
- DTC P1355 / P1356 / P1357 ENG A-STOP DC-DC Converter “B” Over Temperature Short Time / Over Temperature / Internal Electronic Failure
- DTC P1360 ENG A-STOP Battery Performance
- DTC P254F Engine Hood Switch Circuit
- DTC U0073 Troubleshooting for Communication Bus Off
- DTC U0100 Troubleshooting for Lost Communication
- DTC U0101 Troubleshooting for Lost Communication
- DTC U0121 Troubleshooting for Lost Communication
- DTC U0140 Troubleshooting for Lost Communication
- DTC U0141 Troubleshooting for Lost Communication
- DTC U0155 Troubleshooting for Lost Communication
- Inspection of ENG A-STOP Control Module and Its Circuits
- DC/DC Converter Inspection (A/T Model)
- DC/DC Converter Power Supply and Ground Circuit Check (A/T Model)
- Starting Motor Operation Inspection
Repair Instructions
- Procedure after ENG A-STOP Control Module Replacement
- Procedure after Starting Motor Replacement
- ENG A-STOP Control Module Removal and Installation
- DC/DC Converter Removal and Installation (A/T Model)
- Starting Motor Removal and Installation
- Starting Motor Inspection
- Neutral Position Switch Inspection (M/T Model)
- CPP No.1 Switch Removal and Installation (M/T Model)
- CPP No.1 Switch Inspection (M/T Model)
- CPP No.2 Switch Removal and Installation (M/T Model)
- CPP No.2 Switch Inspection (M/T Model)
- Brake Booster Pressure Sensor Removal and Installation
- Brake Booster Pressure Sensor Inspection
- Hood Latch Switch Removal and Installation
- Hood Latch Switch Inspection
- Electric Load Current Sensor & Battery Temperature Sensor Inspection
- ENG A-STOP OFF Switch Removal and Installation
- ENG A-STOP OFF Switch Inspection
- ST2 Relay Inspection