P1604 Startability Malfunction
Diagnostic trouble codes · Vehicles built from Dec 2017
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1604 |
Either condition is met:
|
|


INSPECTION PROCEDURE
- HINT:
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
- If any other DTCs are output, perform troubleshooting for those DTCs first.
- When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
- Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
- When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
- When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
- Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
- If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
- When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
- If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
| Malfunction Recurrence and Inspection Areas |
Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.
The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).
- HINT:
- One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.
- If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.
- If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.
- If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or ECM may be malfunctioning.


All engine speeds recorded in the freeze frame data are between 100 and 250 rpm (the engine cranks but there is no combustion).
- HINT:
- If the engine speed is between 100 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.
- Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.


The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).
- HINT:
- If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.
- Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
- If Long FT is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.
- If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.


When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem Symptoms" and "Systems to Inspect").
Problem Symptoms
- The engine does not crank.
- HINT:
- The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.
- The engine cranking speed is abnormal.
- HINT:
- If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.
- There is no initial combustion.
- HINT:
- If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.
- The engine stalls after starter turnoff.
- HINT:
- If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.
- The initial combustion and starter turnoff occur late.
- HINT:
- If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).
- HINT:
- Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
- When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
- When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
- When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.
- When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
- The engine does not crank.
Systems to Inspect
- Air induction system
- Ignition system
- Fuel system
- Air induction system
| INSPECTION FLOW |
Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.
Freeze Frame Data Item
Result
Suspected Area
Procedure
Engine Speed
0 rpm (no engine cranking at all)
- Battery fully depleted
- Engine assembly (excess friction)
- Starter
- Immobiliser system
- Crankshaft position sensor
- ECM
4 to 9
100 to 250 rpm (engine cranks but no initial combustion*1)
- Fuel pump control system
- Ignition system
- Engine coolant temperature sensor
- Fuel injection system
10 to 14
250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
- Engine assembly (compression loss)
- Fuel injection system
- Fuel pump control system
15 to 23
- HINT:
- *1: First combustion after cranking begins.
- *2: Condition when engine speed increases and starter can be turned off.
- *1: First combustion after cranking begins.
- Battery fully depleted
When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.
Problem Symptoms
Problem Symptom
Suspected Area
Suspected Component
Procedure
The engine does not crank
Battery malfunction
- Battery fully depleted
26 to 31
Starting system
- Starter (includes pinion gear wear or tooth damage)
- Starting system
Immobiliser system
- Immobiliser system
Engine assembly
- Engine assembly (excess friction)
- Drive plate and ring gear wear or tooth damage (for A/T)
- Flywheel wear or tooth damage (for M/T)
Cranking speed too low
Battery malfunction
- Battery fully depleted
32 to 34
Starting system
- Starter
Engine assembly
- Engine assembly (excess friction)
Cranking speed too high
Engine assembly
- Engine assembly (compression loss)
There is no initial combustion
Fuel supply problem
- Cannot maintain pressure due to pressure regulator malfunction
- Fuel injector leak
- Fuel leak from fuel line
- Fuel pump control system
- Fuel pump
35 to 50
Ignition system malfunction
- Spark plug
- Crankshaft position sensor
- Ignition coil
Engine stalls after starter turnoff
Air suction
- Air induction system connections
51 to 56
Deposits in throttle body
- Throttle body assembly
VVT valve does not return properly
- Camshaft timing oil control valve assembly
Mass air flow meter malfunction
- Mass air flow meter
The initial combustion and starter turnoff occur late
Engine coolant temperature sensor malfunction
- Engine coolant temperature sensor
57 to 70
Mass air flow meter malfunction
- Mass air flow meter
Abnormal A/F learned value
- Air fuel ratio sensor
Deviation from fuel injection characteristics
- Fuel injector assembly
Wet-fouled or dry-fouled spark plug
- Spark plug
Lack of fuel pressure
- Pressure regulator
- Fuel pump
- Fuel pump control system
- Battery fully depleted
Systems to Inspect
Troubleshooting by System
Suspected Area
Suspected Component
Procedure
Fuel system troubleshooting A
Abnormal A/F learned value
- Fuel injector assembly
86 to 93
94 to 101
Rough idling
- Crankshaft position sensor
Abnormal fuel pressure
- Fuel
- Fuel leak from fuel line
- Fuel pump
- Pressure regulator
Fuel system troubleshooting B
Abnormal concentration of HC in surge tank
- EVAP VSV system
- Fuel injector assembly
102 to 103
Fuel system troubleshooting C
Injection signal system malfunction
- Fuel injector assembly
- Crankshaft position sensor
- Camshaft position sensor
- ECM
72 to 76
Air induction system troubleshooting
Difference between ISC target value and opening angle when idling
- Engine assembly (compression loss)
- Valve timing
- Engine coolant temperature sensor
- ECM
83 to 85
104 to 107
Ignition system troubleshooting
Camshaft and/or crankshaft position sensor signal malfunction
- Crankshaft position sensor system (including sensor installation)
- Camshaft position sensor system (including sensor installation)
- ECM
77 to 82
108 to 113
- Fuel injector assembly
| 1. CHECK FOR ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs and record the freeze frame data.

- HINT:
- This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
- When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
- The fourth set of freeze frame data is the data recorded when the DTC is stored.
- This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
Result Result
Proceed to
Only DTC P1604 is output
A
DTCs other than P1604 are output
B
|
|
||||
| A | |
| 2. CHECK ENGINE IMMOBILISER SYSTEM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Immobiliser Fuel Cut.
Read the value displayed on the tester.
- OK:
- Immobiliser Fuel Cut is OFF.
- HINT:
- If the engine is started immediately after reconnecting the battery terminal, the engine may stall immediately after it starts due to the intercommunication process between each ECU. For this reason, when starting the engine after reconnecting the battery terminal, first turn the ignition switch to ON and then wait several seconds for the communication process to complete before starting the engine.
- When this operation causes DTC P1604 to be stored, this is due to normal operation of the immobiliser system and does not indicate a malfunction, so clear the DTC and return the vehicle to the customer.
- If the engine is started immediately after reconnecting the battery terminal, the engine may stall immediately after it starts due to the intercommunication process between each ECU. For this reason, when starting the engine after reconnecting the battery terminal, first turn the ignition switch to ON and then wait several seconds for the communication process to complete before starting the engine.
|
|
||||
| OK | |
| 3. CHECK MALFUNCTION CONDITION |
Confirm the problem symptoms.
Result Result
Proceed to
Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
A
The problem symptoms can be reproduced, or the malfunction conditions are known
B
|
|
||||
| A | |
| 4. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Suspected Area
Proceed to
Engine Speed
Battery Voltage
All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
Minimum voltage is below 5 V
Battery fully depleted
A
Minimum voltage is 5 V or higher
- Starter malfunction
- Crankshaft position sensor system
- Excess engine friction
- Immobiliser system
- ECM
B
60 to 250 rpm (engine cranks but no initial combustion)
-
- Fuel pump control system
- Ignition system
- Engine coolant temperature sensor
- Immobiliser system
- Fuel injection system
C
250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
-
- Engine assembly
- Fuel injection system
- Fuel pump control system
D
- HINT:
- When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the freeze frame data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
- *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
- *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
- Immobiliser Fuel Cut
- Engine Speed (starter off)
- Immobiliser Fuel Cut
- Starter malfunction
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 5. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Result
Suspected Area
Proceed to
Battery Voltage
Minimum voltage is 6 V or higher and voltage does not fluctuate*1
Starter system
A
Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
- Crankshaft position sensor system
- ECM
B
Minimum voltage is 5 to 6 V*4
- Excess engine friction
- Battery fully depleted
C
- HINT:
-
*1: The 5 sets of freeze frame data show approximately the same battery voltage.

- *2: The 5 sets of freeze frame data show different battery voltages.
- *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
- *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
-
- Crankshaft position sensor system
|
|
||||
|
|
||||
| A | ||
| ||
| 6. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
Result Result
Proceed to
Normal
A
Abnormal
B
|
|
||||
| A | |
| 7. CHECK CRANKSHAFT POSITION SENSOR |
Disconnect the crankshaft position sensor connector.
Check for oil on the connector terminals.
- OK:
- No oil on the terminals.
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D72-1 (NE) - D97-93 (NE+)
Always
Below 1 Ω
D72-2 (NE-) - D97-117 (NE-)
Always
Below 1 Ω
D72-1 (NE) or D97-93 (NE+) - Body ground
Always
10 kΩ or higher
D72-2 (NE-) or D97-117 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 9. CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 10. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Suspected Area
Proceed to
Coolant Temp, Ambient Temperature, Intake Air
Coolant Temp, Ambient Temperature
Fuel Pump/Speed Status
Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C or more*1
Coolant Temp is 125°C or higher, or below Ambient Temperature by 15°C or more
-
Engine coolant temperature sensor
A
Other than above
All 5 sets of freeze frame data are ON
-
B
At least 1 of the 5 sets of freeze frame data is OFF
Fuel pump control system
C
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C*2
-
At least 1 of the 5 sets of freeze frame data is OFF
Fuel pump control system
C
All 5 sets of freeze frame data are ON
-
B
- HINT:
- *1: A long time had not elapsed after stopping the engine.
- *2: A long time had elapsed after stopping the engine.
- *1: A long time had not elapsed after stopping the engine.
|
|
||||
|
|
||||
| A | ||
| ||
| 11. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Disconnect the fuel pump connector.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
h2-4 - Body ground
Active Test is being performed
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Fuel Pump)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() ![]() |
Disconnect the injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D24-1 - Body ground
Ignition switch ON
11 to 14 V
D25-1 - Body ground
Ignition switch ON
11 to 14 V
D26-1 - Body ground
Ignition switch ON
11 to 14 V
D27-1 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Fuel Injector Assembly)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 13. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 14. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is foreign matter or signs that fuel pump was stuck
A
There is no foreign matter and no signs that fuel pump was stuck
B
|
|
||||
| A | ||
| ||
| 15. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Suspected Area
Proceed to
Coolant Temp, Ambient Temperature, Intake Air
Coolant Temp, Ambient Temperature
Long FT #1
Engine Speed
Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C or more
Coolant Temp is 125°C or higher, or below Ambient Temperature by 15°C or more
-
-
Engine coolant temperature sensor
A
Other than above
-15% or less, or +15% or more
-
- Fuel pump control system
- Fuel injector assembly
B
-15 to +15%
Minimum speed is 300 rpm or more*1
Engine assembly
C
Minimum speed is less than 300 rpm
- Fuel system
- Air induction system
D
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C
-
-15% or less, or +15% or more
-
- Fuel pump control system
- Fuel injector assembly
B
-15 to +15%
Minimum speed is 300 rpm or more*1
Engine assembly
C
Minimum speed is less than 300 rpm
- Fuel system
- Air induction system
D
- HINT:
- *1: Compression loss may have occurred in the engine assembly.
- Fuel pump control system
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 16. INSPECT FUEL INJECTOR ASSEMBLY |
Check that no carbon is stuck to the fuel injector assembly.
- OK:
- No carbon present.
|
|
||||
| OK | |
| 17. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is foreign matter or signs that fuel pump was stuck
A
There is no foreign matter and no signs that fuel pump was stuck
B
|
|
||||
| A | ||
| ||
| 18. CHECK FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Result
Suspected Area
Proceed to
Coolant Temp
Engine coolant temperature is 40°C or less*1
Pressure regulator
A
Engine coolant temperature is 40 to 90°C*2
Fuel injector assembly
B
Engine coolant temperature is 90°C or higher*3
Pressure regulator
A
- HINT:
- *1: If the engine coolant temperature is 40°C or less (after stopping the engine and the vehicle has not been driven for a long period of time), the pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
- *2: If the engine coolant temperature is 40 to 90°C (15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector assembly.
- *3: If the engine coolant temperature is 90°C or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.
|
|
||||
| A | |
| 19. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
| Result |
Proceed to |
| Normal |
A |
| Abnormal |
B |
- HINT:
- If the engine cannot be started, read the values after cranking the engine.
|
|
||||
|
|
||||
| 20. CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
4000 ppm or more
A
Less than 4000 ppm
B
- HINT:
- If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
|
|
||||
| A | |
| 21. CHECK FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly (Click here).
Result Result
Proceed to
Abnormal
A
Normal
B
|
|
||||
| A | ||
| ||
| 22. CHECK THROTTLE BODY ASSEMBLY |
Check if carbon is in the airflow passage.
Result Result
Proceed to
Carbon in passage
A
No carbon present
B
|
|
||||
| A | ||
| ||
| 23. CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leaks.
- OK:
- No leaks in air induction system.
|
|
||||
| OK | |
| 24. PERFORM SIMULATION TEST |
Check if the engine can be started.
Result Result
Proceed to
Engine can be started
A
Engine cannot be started
B
|
|
||||
| A | ||
| ||
| 25. CONFIRM PROBLEM SYMPTOM |
Confirm the problem symptoms.
- HINT:
- The problem symptoms below can be determined by reading the freeze frame data.
Result Problem Symptom
Suspected Area
Proceed to
The engine does not crank
- Battery fully depleted
- Starter (includes pinion gear wear or tooth damage)
- Starter system
- Engine assembly (excess friction)
- Drive plate and ring gear wear or tooth damage (for A/T)
- Flywheel wear or tooth damage (for M/T)
A
Abnormal cranking speed
- Battery fully depleted
- Starter
- Engine assembly (excess friction, compression loss)
B
There is no initial combustion (combustion does not occur even once)*1
- Pressure regulator fuel pressure maintenance
- Fuel injector leak
- Fuel leak from fuel line
- Fuel pump control system
- Fuel pump
- Spark plug
- Crankshaft position sensor system
- Ignition coil system
C
The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2
- Air induction system connections
- Throttle body assembly
- Camshaft timing oil control valve
- Mass air flow meter system
D
The initial combustion and starter turnoff occur late*3
- Engine coolant temperature sensor
- Mass air flow meter
- Air fuel ratio sensor
- Heated oxygen sensor
- Fuel injector
- Spark plug
- Pressure regulator
- Fuel pump
- Fuel pump control system
E
- HINT:
- If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
- *1: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
- *2: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve may have a problem returning.
- *3: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).
- If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 26. PERFORM SIMULATION TEST |
When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.
Result Problem Symptom
Suspected Area
Proceed to
A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely*1
- Battery
- Excess engine friction
- Starter
A
A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely
- Drive plate and ring gear (for A/T)
- Flywheel (for M/T)
- Starter
B
A noise indicating that the starter pinion gear is extending is not heard
- Battery
- Starter
- Starter system
C
- HINT:
- *1: The battery may be fully depleted or there may be excess engine friction.
- Battery
|
|
||||
|
|
||||
| A | |
| 27. INSPECT BATTERY |
Inspect the battery (Click here).
|
|
||||
| OK | |
| 28. CHECK ENGINE ASSEMBLY |
Check that the crankshaft rotates smoothly when rotating it by hand.
- OK:
- Crankshaft rotates smoothly.
- HINT:
- Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
|
|
||||
| OK | ||
| ||
| 29. CHECK STARTER ASSEMBLY |
Remove the starter.
Check for starter pinion gear wear and damage.
- OK:
- There is no wear or damage.
- Result:
Result
Proceed to
NG
A
OK (for A/T)
B
OK (for M/T)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 30. INSPECT BATTERY |
Inspect the battery (Click here).
|
|
||||
| OK | |
| 31. INSPECT STARTER ASSEMBLY |
Inspect the starter (Click here).
|
|
||||
| OK | ||
| ||
| 32. PERFORM SIMULATION TEST |
Check the cranking speed.
Result Problem Symptom
Suspected Area
Proceed to
Cranking speed is slow (100 rpm or less)
- Battery
- Starter
- Excess engine friction
A
Cranking speed is fast (300 rpm or more)*1
Engine compression loss
B
- HINT:
- *1: If the cranking speed is fast, there may be compression loss.
- Battery
|
|
||||
| A | |
| 33. INSPECT BATTERY |
Inspect the battery (Click here).
|
|
||||
| OK | |
| 34. CHECK ENGINE |
Check that the crankshaft rotates smoothly when rotating it by hand.
- OK:
- Crankshaft rotates smoothly.
- HINT:
- Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
|
|
||||
| OK | ||
| ||
| 35. CHECK FUEL INJECTOR ASSEMBLY |
Using a sound scope or screwdriver, check for an injector operating noise while cranking the engine.
- OK:
- Fuel injector operating noise is heard.
|
|
||||
| OK | |
| 36. CHECK FUEL PRESSURE |
Inspect the fuel pressure (Click here).
|
|
||||
| OK | |
| 37. CHECK SPARK PLUG AND SPARK |
Check for sparks (Click here).
|
|
||||
| OK | |
| 38. CONFIRM VEHICLE CONDITION |
Confirm the conditions present when the malfunction occurred based on the customer problem analysis.
Result Problem Symptom
Suspected Area
Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1
Pressure regulator is stuck open
A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
Fuel injector leak
B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
Failure to maintain fuel pressure by pressure regulator
A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
-
C*4
- HINT:
- *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
- *2: Fuel may be leaking from a fuel injector assembly.
- *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.
- *4: From step 71, perform fuel system troubleshooting C (steps 72 to 76).
|
|
||||
|
|
||||
| A | |
| 39. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result Result
Proceed to
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
A*1
Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
B
- HINT:
- If the engine cannot be started, check the fuel pressure after cranking the engine.
- *1: From step 71, perform fuel system troubleshooting C (steps 72 to 76).
- If the engine cannot be started, check the fuel pressure after cranking the engine.
|
|
||||
|
|
||||
| 40. CHECK FUEL INJECTOR ASSEMBLY |
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
4000 ppm or more
A
Less than 4000 ppm
B*1
- HINT:
- If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
- *1: From step 71, perform fuel system troubleshooting C (steps 72 to 76).
- If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
|
|
||||
| A | ||
| ||
| 41. CHECK SPARK PLUG |
Inspect the spark plugs (Click here).
- HINT:
- Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.
|
|
||||
| OK | |
| 42. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
While running the engine, read the value of Engine Speed.
- Standard:
- A value that matches the actual engine speed is constantly output.
- HINT:
- Check the engine speed using a line graph.
- If the engine cannot be started, check the engine speed while cranking the engine.
- If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.
- Check the engine speed using a line graph.
|
|
||||
| OK | |
| 43. CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE) |
![]() ![]() |
Disconnect the ignition coil assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D20-1 (+B) - D20-4 (GND)
Ignition switch ON
11 to 14 V
D21-1 (+B) - D21-4 (GND)
Ignition switch ON
11 to 14 V
D22-1 (+B) - D22-4 (GND)
Ignition switch ON
11 to 14 V
D23-1 (+B) - D23-4 (GND)
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Ignition Coil Assembly)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 44. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Disconnect the ignition coil assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D20-2 (IGF) - D97-82 (IGF1)
Always
Below 1 Ω
D21-2 (IGF) - D97-82 (IGF1)
Always
Below 1 Ω
D22-2 (IGF) - D97-82 (IGF1)
Always
Below 1 Ω
D23-2 (IGF) - D97-82 (IGF1)
Always
Below 1 Ω
D20-2 (IGF) or D97-82 (IGF1) - Body ground
Always
10 kΩ or higher
D21-2 (IGF) or D97-82 (IGF1) - Body ground
Always
10 kΩ or higher
D22-2 (IGF) or D97-82 (IGF1) - Body ground
Always
10 kΩ or higher
D23-2 (IGF) or D97-82 (IGF1) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 45. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
Disconnect the ignition coil assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D20-3 (IGT1) - D97-109 (IGT1)
Always
Below 1 Ω
D21-3 (IGT2) - D97-108 (IGT2)
Always
Below 1 Ω
D22-3 (IGT3) - D97-107 (IGT3)
Always
Below 1 Ω
D23-3 (IGT4) - D97-106 (IGT4)
Always
Below 1 Ω
D20-3 (IGT1) or D97-109 (IGT1) - Body ground
Always
10 kΩ or higher
D21-3 (IGT2) or D97-108 (IGT2) - Body ground
Always
10 kΩ or higher
D22-3 (IGT3) or D97-107 (IGT3) - Body ground
Always
10 kΩ or higher
D23-3 (IGT4) or D97-106 (IGT4) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness is normal, after replacing the ignition coil, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 71 and perform troubleshooting for the ignition system (steps 77 to 82).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 46. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
- Standard:
Control the Fuel Pump / Speed
Specified Condition
ON
Operating sound heard
OFF
Operating sound not heard
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 47. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 71 and perform fuel system troubleshooting (steps 72 to 76).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 48. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
While running the engine, read the value of Engine Speed.
- Standard:
- A value that matches the actual engine speed is constantly output.
- HINT:
- Check the engine speed using a line graph.
- If the engine cannot be started, check the engine speed while cranking the engine.
- If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.
- Check the engine speed using a line graph.
|
|
||||
| OK | |
| 49. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() ![]() |
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D24-1 - Body ground
Ignition switch ON
11 to 14 V
D25-1 - Body ground
Ignition switch ON
11 to 14 V
D26-1 - Body ground
Ignition switch ON
11 to 14 V
D27-1 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Fuel Injector assembly)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 50. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D24-2 - D97-86 (#10)
Always
Below 1 Ω
D25-2 - D97-85 (#20)
Always
Below 1 Ω
D26-2 - D97-84 (#30)
Always
Below 1 Ω
D27-2 - D97-83 (#40)
Always
Below 1 Ω
D24-2 or D97-86 (#10) - Body ground
Always
10 kΩ or higher
D25-2 or D97-85 (#20) - Body ground
Always
10 kΩ or higher
D26-2 or D97-84 (#30) - Body ground
Always
10 kΩ or higher
D27-2 or D97-83 (#40) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 51. CHECK MASS AIR FLOW METER |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
- HINT:
- The A/C switch and all accessory switches should be off, and the shift lever should be in N.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Check MAF in the Data List during idling.
- Standard:
- 2.0 to 4.5 gm/s
|
|
||||
| OK | |
| 52. CHECK AIR INDUCTION SYSTEM |
Check for air leakage in the air induction system [vacuum hose disconnection, cracks, damaged gaskets, etc.].
- HINT:
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
- If Short FT and Long FT are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when racing the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.
- If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
- OK:
- There is no air leakage.
|
|
||||
| OK | |
| 53. CHECK THROTTLE BODY ASSEMBLY |
Disconnect the throttle body assembly connector.
- HINT:
- When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.
Crank the engine and check that it starts.
- Result:
Result
Proceed to
Engine starts
A
Engine does not start
B
Connect the throttle body assembly connector.
- HINT:
- When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).
|
|
||||
| A | |
| 54. CHECK THROTTLE BODY ASSEMBLY |
Check if carbon is in the airflow passage.
- OK:
- No carbon present.
|
|
||||
| OK | |
| 55. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT SYSTEM) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
- HINT:
- When performing the Active Test, make sure the A/C is on.
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
- OK:
Tester Operation
Specified Condition
OFF
Normal engine speed
ON
Soon after OCV switched from OFF to ON, engine idles roughly or stalls
Result Result
Proceed to
NG
A
OK
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 56. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A3-3 (VG) - D97-69 (VG)
Always
Below 1 Ω
A3-2 (E2G) - D97-92 (E2G)
Always
Below 1 Ω
A3-3 (VG) or D97-69 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 71 and perform air induction system troubleshooting (steps 83 to 85). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 86 to 93).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 57. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
- HINT:
- If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 96 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
|
|
||||
| OK | |
| 58. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D32-2 - D97-64 (THW)
Always
Below 1 Ω
D32-1 - D97-72 (E2)
Always
Below 1 Ω
D32-2 or D97-64 (THW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 59. CHECK MASS AIR FLOW METER |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
- HINT:
- The A/C switch and all accessory switches should be off, and the shift lever should be in N.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Check MAF in the Data List during idling.
- Standard:
- 2.0 to 4.5 gm/s
- HINT:
- If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
|
|
||||
| OK | |
| 60. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A3-3 (VG) - D97-69 (VG)
Always
Below 1 Ω
A3-2 (E2G) - D97-92 (E2G)
Always
Below 1 Ω
A3-3 (VG) or D97-69 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 61. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT#1 and Atmosphere Pressure.
Result Data List Item
Result
Suspected Area
Proceed to
Long FT#1
+25% or more or less than -25%
- Air fuel ratio sensor
- Heated oxygen sensor
- Mass air flow meter
- Fuel injector assembly
- ECM
A
Atmosphere Pressure
80 kPa or less (when elevation is 0 m)
Both Data List items listed above
Values are other than above
-
B
- Air fuel ratio sensor
|
|
||||
| A | |
| 62. PERFORM SIMULATION TEST |
Remove the EFI NO.2 and ETCS fuses from the No. 1 engine room relay block.
After 60 seconds or more elapse, install the EFI NO.2 and ETCS fuses.
Check if the engine can be started.
Result Result
Proceed to
Engine can be started
A
Engine cannot be started
B
|
|
||||
| A | |
| 63. INSPECT AIR FUEL RATIO SENSOR |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1.
Confirm that Fuel System Status #1 is CL.
Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1.
Confirm that AF Lambda B1S1 is within the range of 0.95 to 1.05 when idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
- Standard:
Tester Display
Injection Volume
Specified Condition
AFS Voltage B1S1
+12%
Air fuel ratio sensor output voltage is below 3.1 V
-12%
Air fuel ratio sensor output voltage is higher than 3.4 V
Result Result
Proceed to
Normal
A
Abnormal
B
- HINT:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
- If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
|
|
||||
| A | |
| 64. PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine.
- OK:
- Speed is stable.
- HINT:
- After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
|
|
||||
| OK | ||
| ||
| 65. CHECK FUEL PRESSURE |
Inspect the fuel pressure (Click here).
|
|
||||
| OK | |
| 66. CHECK SPARK PLUG |
Inspect the spark plugs (Click here).
Result Result
Proceed to
All cylinders are normal
A
One cylinder is abnormal*1
B
All cylinders are abnormal*2, *3
C
- HINT:
- *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.
- *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
|
|
||||
|
|
||||
| A | |
| 67. CONFIRM VEHICLE CONDITION |
Confirm the conditions present when the malfunction occurred based on the customer problem analysis.
Result Problem Symptom
Suspected Area
Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1
Pressure regulator is stuck open
A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
Fuel injector leak
B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
Failure to maintain fuel pressure by pressure regulator
A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
-
C*4
- HINT:
- *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability of the system to maintain fuel pressure after stopping the engine.
- *2: Fuel may be leaking from a fuel injector assembly.
- *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability of the pressure regulator to maintain fuel pressure after stopping the engine.
- *4: From step 71, perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
|
|
||||
|
|
||||
| A | |
| 68. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result Result
Proceed to
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
A*1
Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
B
- HINT:
- If the engine cannot be started, check the fuel pressure after cranking the engine.
- *1: From step 71, perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- If the engine cannot be started, check the fuel pressure after cranking the engine.
|
|
||||
|
|
||||
| 69. CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
4000 ppm or more
A
Less than 4000 ppm
B*1
- HINT:
- If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
- *1: From step 71, perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
- If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
|
|
||||
| A | ||
| ||
| 70. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 71 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), air induction system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 71. CHECK MALFUNCTION CONDITION |
If the malfunction could not be identified during the inspections in steps 38, 39, 40 and 47, perform fuel system troubleshooting C (steps 72 to 76).
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Steps 38, 39, 40 and 47
Fuel system troubleshooting C
72 to 76
A
If the malfunction could not be identified during the inspection in step 45, perform ignition system troubleshooting (steps 77 to 82).
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Step 45
Ignition system troubleshooting
77 to 82
B
If the malfunction could not be identified during the inspections in steps 55 and 56, perform air induction system troubleshooting (steps 83 to 85). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 86 to 93).
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Step 55 and 56
Air induction system troubleshooting
83 to 85
C
Fuel system troubleshooting A
86 to 93
If the malfunction could not be identified during the inspections in steps 57, 58, 59, 60, 63, 64, 66, 67, 68, 69 and 70, perform fuel system troubleshooting A (steps 94 to 101), fuel system troubleshooting B (steps 102 to 104), air induction system troubleshooting (steps 105 to 107), and ignition system troubleshooting (steps 108 to 113), in that order.
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Steps 57, 58, 59, 60, 63, 64, 66, 67, 68, 69 and 70
Fuel system troubleshooting A
94 to 101
D
Fuel system troubleshooting B
102 to 104
Air induction system troubleshooting
105 to 107
Ignition system troubleshooting
108 to 113
|
|
||||
|
|
||||
|
|
||||
| A | |
| 72. INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly (Click here).
|
|
||||
| OK | |
| 73. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() ![]() |
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D24-1 - Body ground
Ignition switch ON
11 to 14 V
D25-1 - Body ground
Ignition switch ON
11 to 14 V
D26-1 - Body ground
Ignition switch ON
11 to 14 V
D27-1 - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Fuel Injector Assembly)
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 74. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D24-2 - D97-86 (#10)
Always
Below 1 Ω
D25-2 - D97-85 (#20)
Always
Below 1 Ω
D26-2 - D97-84 (#30)
Always
Below 1 Ω
D27-2 - D97-83 (#40)
Always
Below 1 Ω
D24-2 or D97-86 (#10) - Body ground
Always
10 kΩ or higher
D25-2 or D97-85 (#20) - Body ground
Always
10 kΩ or higher
D26-2 or D97-84 (#30) - Body ground
Always
10 kΩ or higher
D27-2 or D97-83 (#40) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 75. CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 76. CHECK CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 77. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 78. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the camshaft position sensor bolt.
Check the connection of the camshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 79. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D72-1 (NE) - D97-93 (NE+)
Always
Below 1 Ω
D72-2 (NE-) - D97-117 (NE-)
Always
Below 1 Ω
D72-1 (NE) or D97-93 (NE+) - Body ground
Always
10 kΩ or higher
D72-2 (NE-) or D97-117 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 80. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
D10-1 - D97-94 (G2)
Always
Below 1 Ω
D10-2 - D97-118 (G2-)
Always
Below 1 Ω
D10-1 or D97-94 (G2) - Body ground
Always
10 kΩ or higher
D10-2 or D97-118 (G2-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 81. CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 82. CHECK CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 83. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches off.
Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.
Result Data List Item
Result
Suspected Area
Proceed to
ISC Learning Value
(engine displacement (liters) x 0.9) or more
- Valve timing
- Compression
A
Less than (engine displacement (liters) x 0.9)
-
B
- Valve timing
|
|
||||
| A | |
| 84. CHECK CYLINDER COMPRESSION PRESSURE |
Inspect the compression (Click here).
|
|
||||
| OK | ||
| ||
| 85. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
|
||||
| OK | |
| 86. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.
Result Vehicle State
Specified Condition
Cranking engine
304 to 343 kPa (3.1 to 3.5 kgf/cm2)
5 minutes after stopping engine
147 kPa (1.5 kgf/cm2) or higher
|
|
||||
| OK | |
| 87. READ VALUE USING INTELLIGENT TESTER (LONG FT #1) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.
Result Data List Item
Result
Suspected Area
Proceed to
Long FT #1
-15 to +15%
- Wire harness or connector
- Fuel
A
+15% or more, or less than -15%
Fuel injector assembly
B
- Wire harness or connector
|
|
||||
| A | |
| 88. PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.
Result Problem Symptom
Suspected Area
Proceed to
Current unstable idling speed or history of unstable idling speed
Crankshaft position sensor system
A
All current and past idling speeds are stable
Fuel
B
- HINT:
- Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.
|
|
||||
| A | |
| 89. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 90. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D72-1 (NE) - D97-93 (NE+)
Always
Below 1 Ω
D72-2 (NE-) - D97-117 (NE-)
Always
Below 1 Ω
D72-1 (NE) or D97-93 (NE+) - Body ground
Always
10 kΩ or higher
D72-2 (NE-) or D97-117 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 91. CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 92. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 93. INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
- HINT:
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
- Make sure the internal connector is securely connected.
- Make sure the fuel pump filter is not clogged.
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
|
|
||||
| OK | ||
| ||
| 94. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result Result
Proceed to
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
A
Below 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
B
|
|
||||
| A | |
| 95. READ VALUE USING INTELLIGENT TESTER (LONG FT #1) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.
Result Data List Item
Result
Suspected Area
Proceed to
Long FT #1
-15 to +15%
- Wire harness or connector
- Fuel
A
+15% or more, or less than -15%
Fuel injector assembly
B
- Wire harness or connector
|
|
||||
| A | |
| 96. PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine and if an unstable idling speed has ever occurred in the past.
Result Problem Symptom
Suspected Area
Proceed to
Current unstable idling speed or history of unstable idling speed
Crankshaft position sensor system
A
All current and past idling speeds are stable
Fuel
B
- HINT:
- Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.
|
|
||||
| A | |
| 97. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 98. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
D72-1 (NE) - D97-93 (NE+)
Always
Below 1 Ω
D72-2 (NE-) - D97-117 (NE-)
Always
Below 1 Ω
D72-1 (NE) or D97-93 (NE+) - Body ground
Always
10 kΩ or higher
D72-2 (NE-) or D97-117 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 99. CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 100. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 101. INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
- HINT:
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
- Make sure the internal connector is securely connected.
- Make sure the fuel pump filter is not clogged.
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
|
|
||||
| OK | |
| 102. CHECK EVAP VSV |
Disconnect the vacuum hose (on the canister side) of the EVAP VSV.

Start the engine.
Idle the engine.
Disconnect the connector of the EVAP VSV.
Check if air flows through the EVAP VSV.
- OK:
- Air does not flow
Connect the connector of the EVAP VSV.
Connect the vacuum hose of the EVAP VSV.
- HINT:
- When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).
|
|
||||
| OK | |
| 103. CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
4000 ppm or more
A
Less than 4000 ppm
B
- HINT:
- If the concentration is 4000 ppm or more, a fuel injector assembly may have a sealing problem.
|
|
||||
| A | ||
| ||
| 104. CHECK INTAKE VALVE |
Check if carbon is on the intake valves.
- Result:
Result
Proceed to
Carbon present
A
No carbon present
B
|
|
||||
| A | ||
| ||
| 105. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.
Result Data List Item
Result
Suspected Area
Proceed to
ISC Learning Value
(engine displacement (liters) x 0.9) or more
- Valve timing
- Compression
A
Less than (engine displacement (liters) x 0.9)
-
B
- Valve timing
|
|
||||
| A | |
| 106. CHECK CYLINDER COMPRESSION PRESSURE |
Inspect the compression (Click here).
|
|
||||
| OK | ||
| ||
| 107. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
|
||||
| OK | |
| 108. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 109. CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR) |
Check the tightening and installation condition of the camshaft position sensor bolt.
Check the connection of the camshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 110. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D72-1 (NE) - D97-93 (NE+)
Always
Below 1 Ω
D72-2 (NE-) - D97-117 (NE-)
Always
Below 1 Ω
D72-1 (NE) or D97-93 (NE+) - Body ground
Always
10 kΩ or higher
D72-2 (NE-) or D97-117 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 111. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D10-1 - D97-94 (G2)
Always
Below 1 Ω
D10-2 - D97-118 (G2-)
Always
Below 1 Ω
D10-1 or D97-94 (G2) - Body ground
Always
10 kΩ or higher
D10-2 or D97-118 (G2-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 112. CHECK CRANKSHAFT POSITION SENSOR |
Replace the crankshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||
| 113. CHECK CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
Check the engine start operation.
- OK:
- Malfunction has been repaired successfully.
|
|
||||
| OK | ||
| ||




