Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER(for AWD) › from 2018.09
RM3160E _53 Suspension _019690 REAR SUSPENSION _0109437 REAR SUSPENSION MEMBER(for AWD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for AWD)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.
C296804

Install the 13 hole plugs to the rear suspension member sub-assembly as shown in the illustration.

HINT:

The upper and lower hole plug shapes are different.



Hide 52271D 2.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

a.
C296957C01
0.052,0.063 0.365,0.302 0.313,0.24 10 false *A 0.167,0.417 0.479,0.573 0.313,0.156 10 false *a 0.667,0.917 0.969,1.156 0.302,0.24 10 false *b 2.771,0.417 3.083,0.656 0.313,0.24 10 false *c 2.76,0.885 3.073,1.125 0.313,0.24 10 false *c
*A View from Underneath
*a Front of the Vehicle
*b Left Side of the Vehicle
*c 45°


Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.


b.
C199924N09
2.063,0.448 2.354,0.448 false 2.042,0.698 2.51,0.698 true 2.385,0.375 2.698,0.552 0.313,0.177 10 false SST 2.542,0.625 2.844,0.833 0.302,0.208 10 false SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C199927C01
1.021,0.792 1.427,0.792 true 1.219,0.979 1.448,0.979 true 2.667,0.844 2.979,1 0.313,0.156 10 false *a 2.188,1.885 2.5,2.042 0.313,0.156 10 false *b 0.719,0.708 1.177,0.906 0.458,0.198 10 false SST 0.917,0.906 1.375,1.104 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52271D 3.INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

a.
C296956C01
0.073,0.063 0.375,0.313 0.302,0.25 10 false *A 0.26,0.417 0.573,0.573 0.313,0.156 10 false *a 0.719,0.885 1.031,1.042 0.313,0.156 10 false *b 2.281,0.427 2.583,0.677 0.302,0.25 10 false *c 2.219,0.896 2.531,1.146 0.313,0.25 10 true *c
*A View from Underneath
*a Front of the Vehicle
*b Left Side of the Vehicle
*c 45°


Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.


b.
C205620N02
1.021,0.406 1.406,0.406 false 1.042,0.708 1.427,0.708 true 0.719,0.323 1.177,0.521 0.458,0.198 10 false SST 0.76,0.615 1.219,0.813 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member front body mounting cushion.



c.
C205621C01
1.271,0.802 1.469,0.802 false 1.292,0.979 1.49,0.979 true 2.781,0.865 3.094,1.021 0.313,0.156 10 false *a 2.24,1.969 2.552,2.125 0.313,0.156 10 false *b 1,0.708 1.292,0.906 0.292,0.198 10 true SST 1,0.906 1.302,1.104 0.302,0.198 10 true SST
*a Turn
*b Hold


Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

SST
09527-17011  
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52276A 4.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION LH

a.
C296955C01
0.104,0.052 0.417,0.365 0.313,0.313 10 false *A 2.573,0.156 2.885,0.313 0.313,0.156 10 false *a 3.052,0.604 3.365,0.76 0.313,0.156 10 false *b
*A View from Underneath
*a Front of the Vehicle
*b Left Side of the Vehicle


Temporarily install the rear suspension member rear body mounting cushion LH while confirming the installation direction.


b.
C199925N02
1.385,0.5 1.208,0.292 1.208,0.292 1.042,0.292 false 0.74,0.208 1.198,0.406 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mounting cushion LH.



c.
C199928C01
1.052,0.604 1.25,0.604 1.25,0.604 1.479,0.771 true 2.719,0.906 3.031,1.063 0.313,0.156 10 false *a 2.198,1.896 2.51,2.052 0.313,0.156 10 false *b 0.781,0.542 1.208,0.74 0.427,0.198 10 true SST
*a Turn
*b Hold


Using SST, install the rear suspension member rear body mounting cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion LH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 52275B 5.INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION RH

a.
C296958C01
0.063,0.063 0.375,0.313 0.313,0.25 10 false *A 0.646,0.271 0.958,0.427 0.313,0.156 10 false *a 0.167,0.729 0.479,0.885 0.313,0.156 10 false *b 0.333,1.542 0.646,1.792 0.313,0.25 10 false *c 2.313,1.563 2.625,1.813 0.313,0.25 10 false *c
*A View from Underneath
*a Front of the Vehicle
*b Right Side of the Vehicle
*c 15°


Temporarily install the rear suspension member rear body mounting cushion RH while confirming the installation direction.


b.
C199926N02
1.896,0.51 2.115,0.281 2.115,0.281 2.438,0.281 false 2.51,0.198 2.969,0.396 0.458,0.198 10 false SST

Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.


HINT:

Use SST with the "F" mark facing the rear suspension member rear body mounting cushion RH.



c.
C199929C01
1.01,0.594 1.281,0.594 1.281,0.594 1.49,0.771 false 2.802,0.896 3.115,1.052 0.313,0.156 10 false *a 2.208,1.885 2.521,2.042 0.313,0.156 10 false *b 0.698,0.521 1.156,0.719 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, install the rear suspension member rear body mounting cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion RH.

SST
09830-10010  (09830-01010, 09830-01020, 09830-01030, 09830-01060)

NOTICE:

If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.



d.

Remove SST from the rear suspension member sub-assembly.


Hide 41651A 6.INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

Hide 48790 7.INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 8.INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89546 9.INSTALL REAR SPEED SENSOR LH

a.
C199896

Install the rear speed sensor LH with the 2 bolts and nut.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 89545 10.INSTALL REAR SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 52272 11.INSTALL REAR SUSPENSION MEMBER UPPER STOPPER

a.
C199916

Install the 2 rear suspension member upper stoppers to the rear suspension member sub-assembly.

NOTICE:

Be sure to install the rear suspension member upper stoppers in the correct direction shown in the illustration.



Hide 52277B 12.INSTALL REAR SUSPENSION MEMBER REAR UPPER STOPPER

a.
C199915

Install the 2 rear suspension member rear upper stoppers to the rear suspension member sub-assembly.


Hide 48720A 13.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

a.
C350898C01
2.135,1.427 1.781,1.427 1.781,1.427 1.781,1.156 true 2.156,1.323 2.417,1.542 0.26,0.219 10 true *a
*a Opening


Temporarily install the rear No. 1 suspension arm assembly LH to the rear suspension member sub-assembly with the bolt and nut.

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Fully tighten the bolt after stabilizing the suspension.

·

Install the rear No. 1 suspension arm assembly with its opening facing downward.




Hide 48710A 14.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51206A 15.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C301600C02
2.792,4.073 2.792,3.906 2.792,3.906 2.948,3.906 false 2.208,4.208 2.729,4.208 false 2.594,4.208 2.594,4.125 2.594,4.125 2.479,4.125 false 0.729,4.188 0.896,4.188 false 1.615,4.188 1.615,4.083 1.615,4.083 1.938,4.083 true 2.979,3.833 3.281,4.021 0.302,0.188 10 false *a 0.563,4.094 0.76,4.281 0.198,0.188 10 true *b 2.771,4.125 3.083,4.281 0.313,0.156 10 false *c 1.531,4.198 1.802,4.375 0.271,0.177 10 true *b
*a Engine Lifter
*b Attachment
*c Wooden Block
V100155

Attachment placement location


Support the rear suspension member sub-assembly with an engine lifter using 2 wooden blocks and 2 attachments or equivalent tools as shown in the illustration.

CAUTION:

Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.


NOTICE:
·

Use the attachments to keep the rear suspension member sub-assembly level.

·

The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.

·

Keep supporting the rear suspension member sub-assembly until the installation has been completed.




b.

Install the rear suspension member sub-assembly with the 2 rear lower suspension braces, rear lower suspension member stopper LH and rear lower suspension member stopper RH, with the 4 bolts and 2 nuts.

C199912C01
0.781,1.438 1.26,1.438 true 5.802,1.427 6.271,1.427 true 0.594,1.344 0.885,1.563 0.292,0.219 10 false *1 6.302,1.344 6.594,1.563 0.292,0.219 10 false *1
*1 Rear Lower Suspension Brace - -


Torque:
Bolt : 158 N*m (1611 kgf*cm, 117 ft.*lbf)
Nut : 32 N*m (326 kgf*cm, 24 ft.*lbf)

NOTICE:

Be sure to install the rear suspension member sub-assembly with the rear lower suspension braces facing in the correct direction as shown in the illustration.



c.

Lower the engine lifter.


Hide 16.INSTALL FRAME WIRE

a.

Install the frame wire to the rear suspension member sub-assembly with the bolt, each clamp and each connector as shown in the illustration.

C296849N01
4.833,0.313 4.979,0.5 0.146,0.188 10 true A 4.156,0.198 4.302,0.406 0.146,0.208 10 true B

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Do not twist the frame wire when installing it.


HINT:

The connector (A) and clamp (B) are only on vehicles with the LED headlight system.



Hide 41110 17.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

Hide 42360A 18.INSTALL REAR DRIVE SHAFT SNAP RING LH

Hide 42360A 19.INSTALL REAR DRIVE SHAFT SNAP RING RH

HINT:

Use the same procedure as for the LH side.


Hide 42340B 20.INSTALL REAR DRIVE SHAFT ASSEMBLY LH

Hide 42330 21.INSTALL REAR DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 42305 22.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

a.
C199841

Secure the rear axle carrier sub-assembly LH in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

HINT:

Pushing out the bushing makes it easier to install the rear axle carrier sub-assembly LH.



c.
C350899C01
1.375,4.167 1.375,4.021 false 0.844,0.854 1.021,1.063 0.177,0.208 10 false A 0.427,1.958 0.646,2.156 0.219,0.198 10 false B 2.625,1.406 2.802,1.583 0.177,0.177 10 true C 2.865,1.396 3.063,1.594 0.198,0.198 10 true C 1.302,4.177 1.542,4.344 0.24,0.167 10 false *a
*a Spacer
V100136

Front of the Vehicle


Temporarily install the rear axle carrier sub-assembly LH with the spacer, nut (B) and 2 bolts (C).

NOTICE:
·

Fully tighten the 2 bolts (C) after temporarily tightening the rear No. 2 suspension arm assembly.

·

Fully tighten the nut (B) after stabilizing the suspension.

·

Be careful not to damage the rear drive shaft outboard joint boot.

·

Be sure to install the rear No. 1 suspension arm assembly with the spacer facing in the correct direction as shown in the illustration.




d.

Install the rear axle carrier sub-assembly LH to the rear upper control arm assembly LH with the bolt (A) and nut.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:
·

Insert the bolt with the threaded end facing the rear of the vehicle.

·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.




Hide 42304 23.TEMPORARILY INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 24.TEMPORARILY INSTALL PARKING BRAKE ASSEMBLY (for LH Side)

Hide 25.TEMPORARILY INSTALL PARKING BRAKE ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 48780E 26.INSTALL REAR TRAILING ARM ASSEMBLY LH

Hide 48760E 27.INSTALL REAR TRAILING ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 28.INSTALL PARKING BRAKE ASSEMBLY (for LH Side)

Hide 29.INSTALL PARKING BRAKE ASSEMBLY (for RH Side)

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 30.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 31.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48508 32.INSTALL REAR LOWER SHOCK ABSORBER BRACKET SUB-ASSEMBLY LH

a.
C202327

Install the rear lower shock absorber bracket sub-assembly LH with the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


Hide 48507A 33.INSTALL REAR LOWER SHOCK ABSORBER BRACKET SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 34.INSTALL REAR STABILIZER BAR

Hide 48802 35.INSTALL REAR STABILIZER LINK SUB-ASSEMBLY LH

Hide 48802 36.INSTALL REAR STABILIZER LINK SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 42440 37.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42410 38.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 42431 39.INSTALL REAR DISC

a.

Install the 2 rear discs.

Click hereBrake>BRAKE (REAR)>REAR BRAKE>INSTALLATION


Hide 42491 40.INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG

a.

Install the 2 parking brake shoe adjusting hole plugs.


Hide 41.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 42.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 42312B 43.INSTALL REAR AXLE SHAFT NUT LH

Hide 42311N 44.INSTALL REAR AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 89546 45.INSTALL REAR SPEED SENSOR LH

Hide 89545 46.INSTALL REAR SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 37100 47.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17430 48.INSTALL TAIL EXHAUST PIPE ASSEMBLY

Hide 48720A 50.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 51.INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89408D 52.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Hide 53.BLEED BRAKE LINE

Hide 54.ADJUST PARKING BRAKE

Hide 41110X 57.INSTALL DIFFERENTIAL INSPECTION PLUG

Hide 58. INSPECT FOR DIFFERENTIAL OIL LEAK

Hide 59.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 48740F 60.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 61.INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 62.INSPECT AND ADJUST REAR WHEEL ALIGNMENT