Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052778 1GR-FE ENGINE MECHANICAL _0255060 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12316A 1.INSTALL FRONT NO. 2 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 2 engine mounting bracket LH with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 3.REMOVE ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine and remove it from the engine stand.

NOTICE:
·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




c.

Place the engine onto a work bench.


Hide 4.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine into the engine compartment.


b.
A267742

Install the front engine mounting insulator LH with the 2 bolts and nut.

Torque:
for bolt : 79 N*m (806 kgf*cm, 58 ft.*lbf)
for nut : 72 N*m (734 kgf*cm, 53 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut


c.

Install the front engine mounting insulator RH with the 2 bolts and nut.

Torque:
for bolt : 79 N*m (806 kgf*cm, 58 ft.*lbf)
for nut : 72 N*m (734 kgf*cm, 53 ft.*lbf)


d.

Remove the 2 engine hangers and 4 bolts.


Hide 32101 5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
A224775E05
1.427,0.354 1.635,0.135 1.635,0.135 2.74,0.135 false 2,0.448 2.313,0.135 false 2.771,0.052 3.135,0.323 0.365,0.271 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolts and their installation holes.


c.
A385837E01
0.563,1.323 0.896,1.323 false 1.354,1.375 1.688,1.375 false 2.177,1.271 2.51,1.271 false 0.385,1.25 0.698,1.448 0.313,0.198 10 false *1 1.167,1.292 1.438,1.5 0.271,0.208 10 false *2 2,1.208 2.219,1.438 0.219,0.229 10 false *3

Install the front spacer, drive plate and rear spacer to the crankshaft.

Text in Illustration
*1 Front Spacer
*2 Drive Plate and Ring Gear
*3 Rear Spacer
V100135

Automatic Transmission Side

HINT:

As the front spacer, the drive plate and ring gear, and the rear spacer are not reversible, be sure to install them in the direction shown in the illustration.



d.

Apply adhesive to 2 or 3 threads at the end of the 8 new bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
A224777E05
1.688,0.271 1.844,0.448 0.156,0.177 10 true 1 1.646,1.698 1.823,1.854 0.177,0.156 10 true 2 2.375,1.01 2.51,1.198 0.135,0.188 10 true 3 0.917,0.958 1.073,1.135 0.156,0.177 10 true 4 2.198,0.448 2.333,0.604 0.135,0.156 10 true 5 1.125,1.49 1.292,1.688 0.167,0.198 10 true 6 2.146,1.521 2.281,1.708 0.135,0.188 10 true 7 1.188,0.417 1.323,0.583 0.135,0.167 10 true 8

Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
83 N*m (846 kgf*cm, 61 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing.



Hide 13405 6.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A224775E05
1.427,0.354 1.635,0.135 1.635,0.135 2.74,0.135 false 2,0.448 2.313,0.135 false 2.771,0.052 3.135,0.323 0.365,0.271 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolts and their installation holes.


c.

Temporarily install the flywheel with 8 new bolts.


d.

Install and tighten the 8 bolts uniformly in several steps.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


e.

Mark the top of the bolts with paint.


f.

Tighten the 8 bolts 90° in the same sequence.


g.

Check that the paint marks are now at a 90° angle to the top.


Hide 31250 7.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 8.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 9.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 32907C 10.CONNECT NO. 1 OIL COOLER HOSE TUBE SUB-ASSEMBLY

a.

Connect the cooler hose tube with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 12371 11.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator to the transmission with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 33030 12.INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 35000 13.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 23801P 14.CONNECT NO. 1 AND NO. 2 FUEL PIPE

a.

Connect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 88711 17.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 87209 20.CONNECT WATER HOSE SUB-ASSEMBLY

a.

Connect the water hoses.


Hide 17105 21.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 22.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17362 23.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 17104 25.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 26.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 45203A 27.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT

Hide 17361 28.INSTALL AIR TUBE (w/ Secondary Air Injection System)

Hide 53785B 30.INSTALL FRONT FENDER APRON TRIM PACKING D

Hide 53784 31.INSTALL FRONT FENDER APRON TRIM PACKING C

Hide 53783 32.INSTALL FRONT FENDER APRON TRIM PACKING B

Hide 53782 33.INSTALL FRONT FENDER APRON TRIM PACKING A

Hide 89465 35.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17450B 36.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 89465 39.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 82121 40.CONNECT ENGINE WIRE

a.
A263400

w/ Secondary Air Injection System:

Attach the clamp and connect the air pump connector.


b.
A263401

Attach the clamp and connect the power steering switch connector.


c.
A267746

w/ Winch:

Install the winch ground wire with the 2 bolts.

Torque:
19 N*m (196 kgf*cm, 14 ft.*lbf)


d.
A267745

Attach the 2 clamps and connect the connector.


e.
A263402

Install the ground wire with the bolt and attach the wire harness clamp.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



f.

Connect the cable to the positive (+) battery terminal.


g.

Connect the wire to the positive (+) battery cable with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


h.

Connect the wire and 2 clips to the engine room junction block with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


i.

Connect the 2 clips and 2 connectors to the engine room junction block.


j.

w/ Secondary Air Injection System:

Attach the clamp and connect the 2 air injection control driver connectors.


k.

Connect the ground wire to the bracket with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


l.

Install the engine room relay block cover.


m.
A263398

Connect the 4 connectors to the junction block.


n.

Attach the wire harness clamp.


o.

p.

Install the junction block cover.


Hide 42.INSTALL AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

Hide 43.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the air cleaner filter element.


Hide 44.INSTALL AIR CLEANER CAP AND HOSE

a.

Install the air cleaner cap and hose.

i.
A456910C01
0.979,2.5 1.146,2.5 1.146,2.5 1.563,2.708 false 1.604,2.698 1.979,2.406 1.979,2.406 2.063,2.406 false 1.115,2.156 1.271,2.354 0.156,0.198 10 false A 0.771,2.406 1.083,2.604 0.313,0.198 10 false *a 2.146,2.333 2.458,2.531 0.313,0.198 10 false *b 2.115,1.49 2.271,1.688 0.156,0.198 10 true A
*a Protrusion (Hose)
*b Protrusion (Throttle body)


Install the air cleaner cap and hose with the bolt and fasten the 4 hook clamps.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Attach the clamp and connect the ventilation hose, vacuum hose and mass air flow meter connector.

HINT:

The direction of the hose clamp is indicated in the illustration.



iii.
A456909C01
2.615,2.385 3.073,2.583 0.458,0.198 10 false (A) 1,2.24 1.313,2.438 0.313,0.198 10 false *a 1.469,2.698 1.781,2.896 0.313,0.198 10 false *b 2.146,1.521 2.302,1.719 0.156,0.198 10 true B 0.365,2.271 0.521,2.469 0.156,0.198 10 false B 0.323,2.708 0.781,2.906 0.458,0.198 10 false 90°
*a Top
*b Front


Tighten the hose clamp so that it is within the standard.

(A):

15 mm or less




Hide 32922A 46.CONNECT OUTLET OIL COOLER HOSE (for Automatic Transmission)

Hide 32921D 47.CONNECT INLET OIL COOLER HOSE (for Automatic Transmission)

Hide 32907A 49.CONNECT OIL COOLER TUBE (w/ Air Cooled Transmission Oil Cooler)

Hide 16571C 51.INSTALL NO. 1 RADIATOR HOSE

Hide 53294C 52.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 53.INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)

Hide 32917 54.INSTALL TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)

Hide 53292A 58.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 51442 59.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 60.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 61.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 62.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 55781E 63.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 64.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 75.PERFORM RESET MEMORY (for Automatic Transmission)

Hide 53301 79.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood with the 4 bolts.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 53301 80.INSPECT HOOD SUB-ASSEMBLY

Hide 53301 81.ADJUST HOOD SUB-ASSEMBLY