Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2014.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273883 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53301 4.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.
A225432

Remove the 8 bolts and hood sub-assembly.

NOTICE:

If the hood support is detached from the ball joint, it become non-reusable. Therefore, do not detach the hood support from the ball joint unless replacing it.



Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.

Remove the cowl top ventilator louver (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 53298 6.REMOVE COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)

Hide 52129B 7.REMOVE FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)

a.

Remove the clip, 5 bolts and front bumper lower cover.


Hide 52129B 8.REMOVE FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)

a.

Remove the clip, 4 bolts and front bumper lower cover.


Hide 52822 9.REMOVE AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)

a.
B353484

Remove the clip and bolt.


b.

Remove the 2 screws and air intake duct LH.


Hide 52821 10.REMOVE AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)

HINT:

Use the same procedure as for the LH side.


Hide 51405A 11.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Remove the 4 bolts.


b.
A224743

Unhook the engine under cover from the vehicle body as shown in the illustration.


Hide 51495 12.REMOVE TRANSMISSION UNDER COVER

a.

Remove the 2 bolts and transmission under cover.


Hide 51450 13.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

a.

Remove the 4 bolts and rear engine under cover assembly.


Hide 53737A 16.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL LH

Hide 53736B 17.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

Hide 53292A 18.REMOVE UPPER RADIATOR SUPPORT SEAL

a.

Remove the 13 clips and upper radiator support seal.


Hide 28800A 21.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 28800 23.REMOVE BATTERY

Hide 74431 24.REMOVE BATTERY TRAY

Hide 52119A 26.REMOVE FRONT BUMPER COVER

Hide 28.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.
A224715

Detach the wire harness clamp.


c.

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 52521 29.REMOVE UPPER CENTER FRONT BUMPER RETAINER

Hide 53293C 30.REMOVE RADIATOR SIDE DEFLECTOR RH

Hide 53294C 31.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 16571 32.REMOVE NO. 1 RADIATOR HOSE

Hide 16572 33.REMOVE NO. 2 RADIATOR HOSE

Hide 16470 34.REMOVE RADIATOR RESERVOIR TANK

Hide 32907C 35.DISCONNECT OIL COOLER TUBE

Hide 16400 37.REMOVE RADIATOR ASSEMBLY

Hide 17360G 38.REMOVE AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)

Hide 44310 41.DISCONNECT VANE PUMP ASSEMBLY

Hide 88703 42.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 43.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88320 44.REMOVE COOLER COMPRESSOR ASSEMBLY

Hide 17410 45.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17361 47.REMOVE AIR TUBE (w/ Secondary Air Injection System)

Hide 17167 48.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 49.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17362 51.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

Hide 17168 52.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 53.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 82715 54.REMOVE WIRING HARNESS CLAMP BRACKET

Hide 11363A 58.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 55303B 59.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 82121 60.DISCONNECT ENGINE WIRE

a.
A222166

Remove the bolt and disconnect the connector.


b.

for 4WD:

i.
A222168

Disconnect the connector and detach the clamp.



c.

Disconnect the ECM connector.

i.
A227938

Detach the clamp and disconnect the 6 connectors.


ii.
A223850

Detach the grommet from the wire harness support.


iii.
A223851

Detach the 4 claws to remove the wire harness support from the vehicle, and then pull out the ECM connector to remove it from the vehicle.



Hide 61.DISCONNECT HEATER WATER HOSE ASSEMBLY

a.
A225434

Disconnect the 2 hoses and heater water hose assembly.


Hide 23801P 62.DISCONNECT NO. 1 AND NO. 2 FUEL PIPES

a.
A222167E02
2.74,1.813 2.667,1.813 2.667,1.813 2.313,1.708 true 2.781,1.75 3,1.958 0.219,0.208 10 true *1

Remove the No. 2 fuel pipe clamp from the fuel tube connector.

Text in Illustration
*1 No. 2 Fuel Pipe Clamp


b.

Disconnect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 63.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 32101 67.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A224775E08
1.427,0.354 1.635,0.135 1.635,0.135 2.74,0.135 true 2,0.448 2.313,0.135 false 2.792,0.073 3.26,0.323 0.469,0.25 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A224777

Remove the 8 bolts, rear spacer, drive plate and ring gear sub-assembly and front spacer.


Hide 68.REMOVE ENGINE ASSEMBLY

a.
U147659E07
2.979,0.448 2.896,0.448 2.896,0.448 2.74,0.667 false 0.354,0.677 0.563,0.677 0.563,0.677 0.792,0.885 true 0.188,0.594 0.354,0.771 0.167,0.177 10 false *1 3.021,0.375 3.208,0.552 0.188,0.177 10 false *2 3.094,1.771 3.198,1.938 0.104,0.167 10 false 1 2.406,1.948 2.51,2.115 0.104,0.167 10 false 2 1.198,1.813 1.302,1.979 0.104,0.167 10 false 1 0.458,1.719 0.563,1.885 0.104,0.167 10 false 2

Install 2 engine hangers with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

HINT:
No. 1 Engine Hanger 12281-31110
No. 2 Engine Hanger 12282-31140
Bolt 91671-C0830



b.

Attach an engine sling device and hang the engine with a chain block.


c.
A225433

Remove the 6 nuts from the front engine mounting insulator LH and RH.


d.

Lift the engine out of the vehicle carefully.

NOTICE:

Make sure the engine is clear of all wiring and hoses.



e.

Remove the front engine mounting insulator LH and RH.


f.

Place the engine onto a work bench.


Hide 69.INSTALL ENGINE STAND

a.

Install the engine onto an engine stand with bolts.