2011-2016 FJ Cruiser · Service Manual ENGINE

P1604 Startability Malfunction

Diagnostic trouble codes · Vehicles built Aug 2011 – Jul 2012

Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.
DTC No.
DTC Detection Condition
Trouble Area
P1604
Either condition is met:
  1. The engine speed is below 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below) (1 trip detection logic).
  2. After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds (1 trip detection logic).
  1. Immobiliser system
  2. Engine assembly (excess friction, compression loss)
  3. Starter
  4. Crankshaft position sensor
  5. VVT sensor
  6. Engine coolant temperature sensor
  7. Fuel pump
  8. Fuel pump control system
  9. Fuel pipes
  10. Fuel injector assembly
  11. Throttle with motor body assembly
  12. Pressure regulator
  13. Battery
  14. Drive plate*1
  15. Flywheel*2
  16. Spark plug
  17. Ignition coil circuit
  18. Intake system
  19. Camshaft timing oil control valve assembly
  20. Mass air flow meter
  21. Air fuel ratio sensor
  22. Valve timing
  23. Fuel
  24. Purge VSV
  25. Intake valve
  26. ECM
  1. *1: for Automatic Transmission Models
  1. *2: for Manual Transmission Models
A220316E01

Reference waveforms showing a normal cold engine start
A226933

Reference waveforms showing a normal warm engine start
A226934

Reference waveforms showing an engine stop after normal idling
A226935

Reference values when there is an air leak in the intake system during starting difficulty
Freeze Frame Data P1604 Startability Malfunction 
Current
P1604: Startability Malfunction
Time Freeze Frame Data
Item
Data1
Data2
Data3
Data4
Data5
Unit
Engine Speed
1625
1042
501
192
129
rpm
Calculate Load
43.1
30.5
38.8
93.3
93.3
%
Vehicle Load
9.0
16.0
28.2
34.1
29.8
%
MAF
6.01
6.67
5.64
2.62
1.54
gm/sec
Atmosphere Pressure
95
95
95
95
95
kPa
Coolant Temp
82
82
82
82
82
°C
Intake Air
51
51
46
46
46
°C
Battery Voltage
12.4
12.5
12.1
12.1
12.0
V
Throttle Sensor Volt %
17.6
17.6
17.6
17.2
17.2
%
Throttle Sensor #2 Volt %
50.1
50.1
50.1
49.8
49.8
%
Throttle Sensor Position
0.0
0.0
0.0
0.0
0.0
%
Throttle Motor DUTY
17.6
17.6
17.6
17.2
17.2
%
Injector (Port)
3.77
2.45
2.90
3.24
7060
ms
Injection Volume (Cylinder 1)
0.000
0.199
0.199
0.199
0.199
ml
Fuel Pump/Speed Status
ON
ON
ON
ON
ON

EVAP (Purge) VSV
0.0
0.0
0.0
0.0
0.0
%
Evap Purge Flow
0.0
0.0
0.0
0.0
0.0
%
Purge Density Learn Value
0.000
0.000
0.000
0.000
0.000

EVAP Purge VSV
OFF
OFF
OFF
OFF
OFF

Purge Cut VSV Duty
0.0
0.0
0.0
0.0
0.0
%
Target Air-Fuel Ratio
0.889
0.913
0.920
0.925
0.833

AF Lambda B1 S1
0.998
0.998
0.998
0.998
0.998

AF Lambda B2 S1
0.998
0.998
0.998
0.998
0.998

AFS Voltage B1 S1
3.29
3.29
3.29
3.29
3.29
V
AFS Voltage B2 S1
3.29
3.29
3.29
3.29
3.29
V
O2S B1 S2
0.00
0.00
0.00
0.00
0.00
V
O2S B2 S2
0.00
0.00
0.00
0.00
0.00
V
Short FT #1
0.0
0.0
0.0
0.0
0.0
%
Long FT #1
0.0
0.0
0.0
0.7
0.0
%
Total FT #1
0.000
0.000
0.000
0.000
0.000

Short FT #2
0.0
0.0
0.0
0.0
0.0
%
Long FT #2
1.5
0.7
0.7
0.7
0.7
%
Total FT #2
0.000
0.000
0.000
0.000
0.000

Fuel System Status #1
OL
OL
OL
OL
OL

Fuel System Status #2
OL
OL
OL
OL
OL

IGN Advance
0.0
17.5
13.5
0.0
0.0
deg
Knock Feedback Value
-3.0
-3.0
-3.0
-3.0
-3.0
CA
Knock Correct Learn Value
23.1
23.1
23.1
23.1
23.1
CA
VVT Control Status #1
OFF
OFF
OFF
OFF
OFF

Starter Signal
Close
Close
Close
Close
Close


WIRING DIAGRAM

A226844E01
A226846E01
A226845E01

INSPECTION PROCEDURE

HINT:
  1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
    As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
  2. If any other DTCs are output, perform troubleshooting for those DTCs first.
  3. When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
  4. Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  5. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here ).
  6. When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
  7. Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
  8. If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
  9. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
  10. If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.


Malfunction Recurrence and Inspection Areas
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    1. The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

      HINT:
      One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.

      1. If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.
      2. If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

      3. If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or an ECM may be malfunctioning.

        A215383E01

    2. All engine speeds recorded in the freeze frame data are between 100 and 250 rpm (the engine cranks but there is no combustion).

      HINT:
      If the engine speed is between 100 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.

        A215384E01

    3. The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

      HINT:
      If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.

      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
      2. If Long FT #1 is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

      3. If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.

        A215383E02

  2. When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem symptoms" and "Systems to inspect")

    1. Problem symptoms

      1. The engine does not crank.

        HINT:
        The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.

      2. The engine cranking speed is abnormal.

        HINT:
        If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.

      3. There is no initial combustion.

        HINT:
        If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.

      4. The engine stalls after starter turnoff.

        HINT:
        If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.

      5. The initial combustion and starter turnoff occur late.

        HINT:
        If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).

        HINT:
        Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
        1. When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
        2. When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
        3. When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.

    2. Systems to inspect.

      1. Intake system
      2. Ignition system
      3. Fuel system


INSPECTION FLOW
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    Freeze Frame Data Item
    Result
    Suspected Area
    Procedure
    Engine Speed
    0 rpm (no engine cranking at all)
    1. Battery fully depleted
    2. Engine assembly (excess friction)
    3. Starter
    4. Crankshaft position sensor
    5. ECM
    4 to 9
    100 to 250 rpm (engine cranks but no initial combustion*1)
    1. Fuel pump control system
    2. Ignition system
    3. Immobiliser system
    4. Engine coolant temperature sensor
    5. Fuel injection system
    10 to 14
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
    1. Engine assembly (compression loss)
    2. Fuel injection system
    3. Fuel pump control system
    15 to 24

    HINT:
    1. *1: First combustion after cranking begins.
    2. *2: Condition when engine speed increases and starter can be turned off.

  2. When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

    1. Problem symptoms

      Problem Symptom
      Suspected Area
      Suspected Component
      Procedure
      The engine does not crank
      Battery malfunction
      1. Battery fully depleted
      26 to 31
      Starting system
      1. Starter (includes pinion gear wear or tooth damage)
      2. Starting system
      Engine assembly
      1. Engine assembly (excess friction)
      2. Drive plate wear or tooth damage
      3. Flywheel wear or tooth damage
      Cranking speed too low
      Battery malfunction
      1. Battery fully depleted
      32 to 34
      Starting system
      1. Starter
      Engine assembly
      1. Engine assembly (excess friction)
      Cranking speed too high
      Engine assembly
      1. Engine assembly (compression loss)
      There is no initial combustion
      Fuel supply problem
      1. Cannot maintain pressure due to pressure regulator malfunction
      2. Fuel injector leak
      3. Fuel leak from fuel line
      4. Fuel pump control system
      5. Fuel pump
      35 to 50
      Immobiliser system
      1. Immobiliser system
      Ignition system malfunction
      1. Spark plug
      2. Crankshaft position sensor
      3. Ignition coil
      Engine stalls after starter turnoff
      Air suction
      1. Intake system connections
      51 to 57
      Deposits in throttle body with motor assembly
      1. Throttle body with motor assembly
      VVT valve does not return properly
      1. Camshaft timing oil control valve assembly
      Mass air flow meter malfunction
      1. Mass air flow meter
      The initial combustion and starter turnoff occur late
      Engine coolant temperature sensor malfunction
      1. Engine coolant temperature sensor
      58 to 71
      Mass air flow meter malfunction
      1. Mass air flow meter
      Abnormal A/F learning value
      1. Air fuel ratio sensor
      Deviation from fuel injection characteristics
      1. Fuel injector assembly
      Wet-fouled or dry-fouled spark plug
      1. Spark plug
      Lack of fuel pressure
      1. Pressure regulator
      2. Fuel pump
      3. Fuel pump control system

    2. Systems to inspect.

      Troubleshooting by System
      Suspected Area
      Suspected Component
      Procedure
      Fuel system troubleshooting A
      Abnormal A/F learning value
      1. Fuel injector assembly
      88 to 95
      96 to 103
      Rough idling
      1. Crankshaft position sensor
      Abnormal fuel pressure
      1. Fuel
      2. Fuel leak from fuel line
      3. Fuel pump
      4. Pressure regulator
      Fuel system troubleshooting B
      Abnormal concentration of HC in surge tank
      1. Purge VSV system
      2. Fuel injector assembly
      104 to 106
      Fuel system troubleshooting C
      Injection signal system malfunction
      1. Fuel injector assembly
      2. Crankshaft position sensor
      3. VVT sensor
      4. ECM
      73 to 77
      Intake system troubleshooting
      Difference between ISC target value and opening angle when idling
      1. Engine assembly (compression loss)
      2. Valve timing
      3. Engine coolant temperature sensor
      4. ECM
      85 to 87
      107 to 109
      Ignition system troubleshooting
      Camshaft and/or crankshaft position sensor signal malfunction
      1. Crankshaft position sensor system (including sensor installation)
      2. VVT sensor system (including sensor installation)
      3. ECM
      78 to 84
      110 to 116


1. CHECK ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. A103809E46
    Read the DTCs and record the Freeze Frame Data.

    HINT:
    1. This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
    2. When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
    3. The fourth set of freeze frame data is the data recorded when then the DTC is stored.

    Result 
    Result
    Proceed to
    Only DTC P1604 is output
    A
    DTCs other than P1604 are output
    B



B
GO TO DTC CHART (Click here)
A


2. CHECK ENGINE IMMOBILISER SYSTEM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Immobiliser Fuel Cut.

  1. Read the value displayed on the intelligent tester.

    OK:
    Immobiliser Fuel Cut is OFF

    HINT:
    If the engine is cranked immediately after reconnecting the battery cable (key verification for immobiliser system not completed), the engine cannot be started. Key verification needs to wait for several seconds after turning the ignition switch to ON.



NG
REPAIR ENGINE IMMOBILISER SYSTEM
OK


3. CHECK MALFUNCTION CONDITION
  1. Confirm the problem symptoms.

    Result 
    Result
    Proceed to
    Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
    A
    The problem symptoms can be reproduced, or the malfunction conditions are known
    B



B
Go to step 25
A


4. READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Engine Speed
    Battery Voltage
    All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
    Minimum voltage is less than 5 V
    Battery fully depleted
    A
    Minimum voltage is 5 V or higher
    1. Starter malfunction
    2. Crankshaft position sensor system
    3. Excess engine friction
    4. ECM
    B
    60 to 250 rpm (engine cranks but no initial combustion)
    -
    1. Fuel pump control system
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Fuel injection system
    C
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
    -
    1. Engine assembly
    2. Fuel injection system
    3. Fuel pump control system
    D

    HINT:
    When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the Freeze Frame Data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
    *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
    *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
    1. Immobiliser Fuel Cut
    2. Engine Speed (Starter Off)
    3. Shift SW Status (R, D Range)



B
Go to step 5

C
Go to step 10

D
Go to step 15

E
Go to step 51
A

CHARGE OR REPLACE BATTERY

5. READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Battery Voltage
    Minimum voltage is 6 V or higher and voltage does not fluctuate*1
    Starter system
    A
    Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
    1. Crankshaft position sensor system
    2. ECM
    B
    Minimum voltage is 5 to 6 V*4
    1. Excess engine friction
    2. Battery fully depleted
    C

    HINT:

    1. A217930E01
      *1: The 5 sets of freeze frame data show approximately the same battery voltage.
    2. *2: The 5 sets of freeze frame data show different battery voltages.
    3. *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
    4. *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
Go to step 6

C
CHECK AND REPAIR ENGINE OR BATTERY
A

CHECK STARTER SIGNAL CIRCUIT (Click here)

6. CHECK CRANKSHAFT POSITION SENSOR INSTALLATION
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


7. CHECK CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.

  1. Check for oil on the connector terminals.

    OK:
    No oil on the terminals.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


8. INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


9. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-1 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-1 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

10. READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Ambient Temperature, Intake Air
    Coolant Temp, Ambient Temperature
    Fuel Pump/Speed Status
    Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C or more*1
    Coolant Temp is 125°C or more, or lower than Ambient Temperature by 15°C or more
    -
    Engine coolant temperature sensor
    A
    Other than above
    All 5 sets of freeze frame data are ON
    -
    B
    At least 1 of the 5 sets of freeze frame data is OFF
    Fuel pump control system
    C
    Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C*2
    -
    At least 1 of the 5 sets of freeze frame data is OFF
    Fuel pump control system
    C
    All 5 sets of freeze frame data are ON
    -
    B

    HINT:
    1. *1: A long time had not elapsed after stopping the engine.
    2. *2: A long time had elapsed after stopping the engine.



B
Go to step 11

C
CHECK FUEL PUMP CONTROL SYSTEM (Click here)
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

11. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
A190138E06
  1. Connect the intelligent tester to the DLC3.

  1. Disconnect the fuel pump connector.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L5-4 - Body ground
    Active Test is being performed
    11 to 14 V

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Pump)



NG
CHECK FUEL PUMP CONTROL SYSTEM (Click here)
OK


12. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
A167963E16
  1. Disconnect the injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Injector assedmbly)



NG
CHECK POWER SOURCE CIRCUIT (Click here)
OK


13. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 14
A

REPAIR OR REPLACE FUEL LINE

14. CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM

15. READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Ambient Temperature, Intake Air
    Coolant Temp, Ambient Temperature
    Long FT #1
    Long FT #2
    Engine Speed
    Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C or more
    Coolant Temp is 125°C or more, or lower than Ambient Temperature by 15°C or more
    -
    -
    Engine coolant temperature sensor
    A
    Other than above
    -15% or less, or +15% or more
    -
    1. Fuel pump control system
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is below 300 rpm
    1. Fuel system
    2. Intake air system
    D
    Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C
    -
    -15% or less, or +15% or more
    -
    1. Fuel pump control system
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is below 300 rpm
    1. Fuel system
    2. Intake air system
    D

    HINT:
    *1: Compression loss may have occurred in the engine assembly.



B
Go to step 16

C
CHECK AND REPAIR ENGINE ASSEMBLY

D
Go to step 18
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

16. INSPECT FUEL INJECTOR ASSEMBLY
  1. Check that no carbon is stuck to the fuel injector assembly.

    OK:
    No carbon present.



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


17. CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM

18. READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    Engine coolant temperature is 40°C (104°F) or less*1
    Pressure regulator
    A
    Engine coolant temperature is 40 to 90°C (104 to 194°F)*2
    Fuel injector assembly
    B
    Engine coolant temperature is 90°C (194°F) or more*3
    Pressure regulator assembly
    A

    HINT:
    *1: If the engine coolant temperature is 40°C (104°F) or less (after stopping the engine and the vehicle is not driven for a long period of time), the pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: If the engine coolant temperature is 40 to 90°C (104 to 194°F)(15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector.
    *3: If the engine coolant temperature is 90°C (194°F) or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator assembly failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.



B
Go to step 20
A


19. CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures (Click here).

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, read the values after cranking the engine.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 24
A

REPLACE PRESSURE REGULATOR ASSEMBLY (Click here)

20. CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B

    HINT:
    If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.



B
Go to step 22
A


21. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injectors (Click here).

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 22
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)

22. CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.

    Result 
    Result
    Proceed to
    Carbon in passage
    A
    No carbon present
    B



B
Go to step 23
A

CLEAN OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)

23. CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


24. PERFORM SIMULATION TEST
  1. Check if the engine can be started.

    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 25
A

END

25. CONFIRM PROBLEM SYMPTOM
  1. Confirm the problem symptoms.

    HINT:
    The problem symptoms below can be determined by reading the freeze frame data.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    The engine does not crank
    1. Battery fully depleted
    2. Starter (includes pinion gear wear or teeth damage)
    3. Starter system
    4. Engine assembly (excess friction)
    5. Drive plate wear or teeth damage
    6. Flywheel wear or teeth damage
    A
    Abnormal cranking speed
    1. Battery fully depleted
    2. Starter
    3. Engine assembly (excess friction, compression loss)
    B
    There is no initial combustion (combustion does not occur even once)*1
    1. Pressure regulator fuel pressure maintenance
    2. Fuel injector leak
    3. Fuel leak from fuel line
    4. Fuel pump control system
    5. Fuel pump
    6. Spark plug
    7. Crankshaft position sensor system
    8. Ignition coil system
    C
    The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter system
    D
    The initial combustion and starter turnoff occur late*3
    1. Engine coolant temperature sensor
    2. Mass air flow meter
    3. Air fuel ratio sensor
    4. Fuel injector assembly
    5. Spark plug
    6. Pressure regulator assembly
    7. Fuel pump
    8. Fuel pump control system
    E

    HINT:
    1. If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
    2. *1: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
    3. *2: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve assembly may have a problem returning.
    4. *3: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).



B
Go to step 32

C
Go to step 35

D
Go to step 51

E
Go to step 58
A


26. PERFORM SIMULATION TEST
  1. When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely.*1
    1. Battery
    2. Excess engine friction
    3. Starter
    A
    A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely.
    1. Drive plate
    2. Flywheel
    3. Starter
    B
    A noise indicating that the starter pinion gear is extending is not heard
    1. Battery
    2. Starter
    3. Starter system
    C

    HINT:
    *1: The battery may be fully depleted or there may be excess engine friction.



B
Go to step 29

C
Go to step 30
A


27. INSPECT BATTERY
A228082E01
  1. Check the electrolyte quantity.

    OK:
    Electrolyte quantity is within the specified range.

  1. Inspect the battery voltage.

    1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

    2. Measure the battery voltage.

      Standard voltage:
      12.5 to 12.9 V (electrolyte is at 20°C (68°F))

      HINT:
      If the result is not as specified, recharge or replace the battery.

    3. Measure the battery voltage when cranking the engine.

      Standard voltage:
      Approximately 6 V or higher (0°C (32°F) or higher)

      HINT:
      When the battery is depleted, the horn becomes quieter.



NG
CHARGE OR REPLACE BATTERY
OK


28. CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

INSPECT STARTER ASSEMBLY (Click here)

29. CHECK STARTER ASSEMBLY
  1. Remove the starter (Click here).

  1. Check for starter pinion gear wear and damage.

    Standard:
    There is no wear or damage.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    (for Manual Transmission models)
    B
    OK
    (for Automatic Transmission models)
    C



B
REPLACE FLYWHEEL SUB-ASSEMBLY (Click here)

C
REPLACE DRIVE PLATE AND RING GEAR (Click here)
A

REPLACE STARTER (Click here)

30. INSPECT BATTERY
A228082E01
  1. Check the electrolyte quantity.

    OK:
    Electrolyte quantity is within the specified range.

  1. Inspect the battery voltage.

    1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

    2. Measure the battery voltage.

      Standard voltage:
      12.5 to 12.9 V (electrolyte is at 20°C (68°F))

      HINT:
      If the result is not as specified, recharge or replace the battery.

    3. Measure the battery voltage when cranking the engine.

      Standard voltage:
      Approximately 6 V or higher (0°C (32°F) or higher)

      HINT:
      When the battery is depleted, the horn becomes quieter.



NG
CHARGE OR REPLACE BATTERY
OK


31. INSPECT STARTER ASSEMBLY
  1. Inspect the starter (Click here).



NG
REPLACE STARTER (Click here)
OK

CHECK STARTER SIGNAL CIRCUIT (Click here)

32. PERFORM SIMULATION TEST
  1. Check the cranking speed.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Cranking speed is slow (100 rpm or less)
    1. Battery
    2. Starter
    3. Excess engine friction
    A
    Cranking speed is fast (300 rpm or more)*1
    Engine compression loss
    B

    HINT:
    *1: If the cranking speed is fast, there may be compression loss.



B
CHECK AND REPAIR ENGINE ASSEMBLY
A


33. INSPECT BATTERY
A228082E01
  1. Check the electrolyte quantity.

    OK:
    Electrolyte quantity is within the specified range.

  1. Inspect the battery voltage.

    1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

    2. Measure the battery voltage.

      Standard voltage:
      12.5 to 12.9 V (electrolyte is at 20°C (68°F))

      HINT:
      If the result is not as specified, recharge or replace the battery.

    3. Measure the battery voltage when cranking the engine.

      Standard voltage:
      Approximately 6 V or higher (0°C (32°F) or higher)

      HINT:
      When the battery is depleted, the horn becomes quieter.



NG
CHARGE OR REPLACE BATTERY
OK


34. CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

INSPECT STARTER ASSEMBLY (Click here)

35. CHECK FUEL INJECTOR ASSEMBLY
  1. Using a sound scope or screwdriver, check for an injector operating noise while cranking the engine.

    OK:
    Fuel injector operating noise is heard.



NG
Go to step 48
OK


36. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
Go to step 46
OK


37. INSPECT SPARK PLUG AND SPARK
  1. Inspect for sparks (Click here).



NG
Go to step 41
OK


38. CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator assembly
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator assembly may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *4: From step 72, perform fuel system troubleshooting C (steps 73 to 77).



B
Go to step 40

C
Go to step 72
A


39. CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures (Click here).

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 72, perform fuel system troubleshooting C (steps 73 to 77).



B
Go to step 72
A

REPLACE PRESSURE REGULATOR ASSEMBLY (Click here)

40. CHECK FUEL INJECTOR ASSEMBLY
  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B*1

    HINT:
    1. If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
    2. *1: From step 72, perform fuel system troubleshooting C (steps 73 to 77).



B
Go to step 72
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)

41. INSPECT SPARK PLUG
  1. Inspect the spark plugs (Click here).

HINT:
Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.



NG
REPLACE SPARK PLUG (Click here)
OK


42. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the [Engine Speed] value.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
CHECK CRANKSHAFT POSITION SENSOR CIRCUIT
OK


43. CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE)
A115969E48
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B7-1 (+B) - B7-4 (GND)
    Ignition switch ON
    11 to 14 V
    B24-1 (+B) - B24-4 (GND)
    Ignition switch ON
    11 to 14 V
    B6-1 (+B) - B6-4 (GND)
    Ignition switch ON
    11 to 14 V
    B23-1 (+B) - B23-4 (GND)
    Ignition switch ON
    11 to 14 V
    B5-1 (+B) - B5-4 (GND)
    Ignition switch ON
    11 to 14 V
    B20-1 (+B) - B20-4 (GND)
    Ignition switch ON
    11 to 14 V

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Coil Assembly)



NG
CHECK POWER SOURCE CIRCUIT (Click here)
OK


44. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B7-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B24-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B6-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B23-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B5-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B20-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B7-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B24-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B6-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B23-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B5-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B20-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


45. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B7-3 (IGT1) - B49-24 (IGT1)
    Always
    Below 1 Ω
    B24-3 (IGT2) - B49-25 (IGT2)
    Always
    Below 1 Ω
    B6-3 (IGT3) - B49-26 (IGT3)
    Always
    Below 1 Ω
    B23-3 (IGT4) - B49-27 (IGT4)
    Always
    Below 1 Ω
    B5-3 (IGT5) - B49-28 (IGT5)
    Always
    Below 1 Ω
    B20-3 (IGT6) - B48-25 (IGT6)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B7-3 (IGT1) or B49-24 (IGT1) - Body ground
    Always
    10 kΩ or higher
    B24-3 (IGT2) or B49-25 (IGT2) - Body ground
    Always
    10 kΩ or higher
    B6-3 (IGT3) or B49-26 (IGT3) - Body ground
    Always
    10 kΩ or higher
    B23-3 (IGT4) or B49-27 (IGT4) - Body ground
    Always
    10 kΩ or higher
    B5-3 (IGT5) or B49-28 (IGT5) - Body ground
    Always
    10 kΩ or higher
    B20-3 (IGT6) or B48-25 (IGT6) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the ignition coil, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform troubleshooting for the ignition system (steps 78 to 84).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)

46. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:
    Control the Fuel Pump / Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
CHECK FUEL PUMP CONTROL SYSTEM (Click here)
OK


47. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform fuel system troubleshooting (steps 73 to 77).



B
CHECK FUEL PUMP CONTROL SYSTEM (Click here)
A

REPAIR OR REPLACE FUEL LINE

48. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the [Engine Speed] value.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


49. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
A167963E16
  1. Disconnect the injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Injector Assembly)



NG
CHECK POWER SOURCE CIRCUIT (Click here)
OK


50. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
  1. Disconnect the injector connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B11-2 - B50-6 (#10)
    Always
    Below 1 Ω
    B25-2 - B50-1 (#20)
    Always
    Below 1 Ω
    B10-2 - B50-7 (#30)
    Always
    Below 1 Ω
    B21-2 - B50-2 (#40)
    Always
    Below 1 Ω
    B9-2 - B50-8 (#50)
    Always
    Below 1 Ω
    B18-2 - B50-3 (#60)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B11-2 or B50-6 (#10) - Body ground
    Always
    10 kΩ or higher
    B25-2 or B50-1 (#20) - Body ground
    Always
    10 kΩ or higher
    B10-2 or B50-7 (#30) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B50-2 (#40) - Body ground
    Always
    10 kΩ or higher
    B9-2 or B50-8 (#50) - Body ground
    Always
    10 kΩ or higher
    B18-2 or B50-3 (#60) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

51. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
Go to step 57
OK


52. CHECK INTAKE SYSTEM
  1. Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).

    HINT:
    1. If the accelerator pedal is released after revving the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
    2. If Short FT and Long FT #1 are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when revving the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.

    OK:
    There is no air leakage.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


53. CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Disconnect the throttle with motor body assembly connector.

    HINT:
    When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.

  1. Crank the engine and check that it starts.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start
    B



B
Go to step 55
A


54. CHECK THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.

    OK:
    No carbon present.



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY
OK


55. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT SYSTEM)
A219635E01
  1. Connect the intelligent tester to the DLC3.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).

    HINT:
    When performing the Active Test, make sure the A/C is on and the shift lever is in N.

  1. Check the engine speed while operating the Camshaft Timing Oil Control Valve (OCV) assembly using the tester.

    OK:
    Tester Operation
    Specified Condition
    OCV OFF
    Normal engine speed
    OCV ON
    Soon after OCV switched from OFF to ON, engine idles roughly or stalls

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) (Click here)
OK


56. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the tester on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).

    HINT:
    When performing the Active Test, make sure the A/C is on and the shift lever is in N.

  1. Check the engine speed while operating the Oil Control Valve (OCV) using the tester.

    OK*1:
    Tester Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

    HINT:
    1. *1: From step 72, perform intake system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).
    2. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    3. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.



B
Go to step 72
A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) (Click here)

57. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform intake system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)

58. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


59. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B52-2 - B49-17 (THW)
    Always
    Below 1 Ω
    B52-1 - B48-8 (ETHW)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B52-2 or B49-17 (THW) - Body ground
    Always
    10 kΩ or higher
    B52-1 or B48-8 (ETHW) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


60. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).

HINT:
If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


61. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.
  3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


62. READ VALUE USING INTELLIGENT TESTER (LONG FT #1, FT #2 - ATMOSPHERE PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 /Long FT #2 and Atmosphere Pressure.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    Long FT #2
    +25% or more or less than -25%
    1. Air fuel ratio sensor
    2. Mass air flow meter
    3. Fuel injector assembly
    4. ECM
    A
    Atmosphere Pressure
    80 kPa or less (when altitude is 0 m)
    Both Data List items listed above
    Values are other than above
    -
    B



B
Go to step 66
A


63. PERFORM SIMULATION TEST
  1. Remove the EFI and ETCS fuses from the engine room relay block.

  1. After 60 seconds or more elapse, install the EFI and ETCS fuses.

  1. Check if the engine can be started.

    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 66
A


64. INSPECT AIR FUEL RATIO SENSOR
A215382E01
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1 and Fuel System Status #2.

  1. Confirm that Fuel System Status #1 and Fuel System Status #2 are both CL.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1.

  1. Confirm that AF Lambda B1S1 are both within the range of 0.95 to 1.05 when idling.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

  1. Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

    Standard:
    Tester Display
    Injection Volume
    Specified Condition
    AFS Voltage B1S1
    AFS Voltage B2S1
    +25%
    Air fuel ratio sensor output voltage is below 3.1 V
    -12.5%
    Air fuel ratio sensor output voltage is higher than 3.4 V

    HINT:
    1. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    2. If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


65. PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine.

    OK:
    Speed is stable.

    HINT:
    After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE MASS AIR FLOW METER (Click here)

66. CHECK FUEL PRESSURE
  1. Check the fuel pressure (Click here).



NG
Go to step 71
OK


67. INSPECT SPARK PLUG
  1. Inspect the spark plugs (Click here).

    Result 
    Result
    Proceed to
    All cylinders are normal
    A
    One cylinder is abnormal*1
    B
    All cylinders are abnormal*2, *3
    C

HINT:
  1. *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
  2. *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
  3. *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.



B
REPLACE SPARK PLUG (ABNORMAL CYLINDER) (Click here)

C
REPLACE SPARK PLUG (ALL CYLINDER) (Click here)
A


68. CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator assembly is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector.
    *3: The pressure regulator assembly may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *4: From step 72, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



B
Go to step 70

C
Go to step 72
A


69. CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures (Click here).

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 72, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



B
Go to step 72
A

REPLACE PRESSURE REGULATOR (Click here)

70. CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B*1

    HINT:
    1. If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
    2. *1: From step 72, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



B
Go to step 72
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)

71. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.



B
CHECK FUEL PUMP CONTROL SYSTEM (Click here)
A

REPAIR OR REPLACE FUEL LINE

72. CHECK MALFUNCTION CONDITION
  1. If the malfunction could not be identified during the inspection in steps 38, 39, 40 and 47, perform fuel system troubleshooting C (steps 73 to 77).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 38, 39, 40 and 47
    Fuel system troubleshooting C
    73 to 77
    A

  1. If the malfunction could not be identified during the inspection in step 45, perform ignition system troubleshooting (steps 78 to 84).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 45
    Ignition system troubleshooting
    78 to 84
    B

  1. If the malfunction could not be identified during the inspection in steps 55, 56 and 57, perform intake air system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 55, 56, 57
    Intake air system troubleshooting
    85 to 87
    C
    Fuel system troubleshooting A
    88 to 95

  1. If the malfunction could not be identified during the inspection in steps 58, 59, 60, 63, 64, 65, 66, 67, 68, 69, 70 and 71, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake air system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 58, 59, 60, 63, 64, 65, 66, 67, 68, 69, 70 and 71
    Fuel system troubleshooting A
    96 to 103
    D
    Fuel system troubleshooting B
    104 to 106
    Intake air system troubleshooting
    107 to 109
    Ignition system troubleshooting
    110 to 116



B
Go to step 78

C
Go to step 85

D
Go to step 96
A


73. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injectors (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


74. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
A167963E16
  1. Disconnect the injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Injector)



NG
CHECK POWER SOURCE CIRCUIT (Click here)
OK


75. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
  1. Disconnect the injector assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B11-2 - B50-6 (#10)
    Always
    Below 1 Ω
    B25-2 - B50-1 (#20)
    Always
    Below 1 Ω
    B10-2 - B50-7 (#30)
    Always
    Below 1 Ω
    B21-2 - B50-2 (#40)
    Always
    Below 1 Ω
    B9-2 - B50-8 (#50)
    Always
    Below 1 Ω
    B18-2 - B50-3 (#60)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B11-2 or B50-6 (#10) - Body ground
    Always
    10 kΩ or higher
    B25-2 or B50-1 (#20) - Body ground
    Always
    10 kΩ or higher
    B10-2 or B50-7 (#30) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B50-2 (#40) - Body ground
    Always
    10 kΩ or higher
    B9-2 or B50-8 (#50) - Body ground
    Always
    10 kΩ or higher
    B18-2 or B50-3 (#60) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


76. INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here ).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


77. INSPECT VVT SENSOR
  1. Inspect the VVT sensor.

HINT:
  1. For intake side of bank 1 or bank 2 (Click here).
  2. For exhaust side of bank 1 or bank 2 (Click here).



NG
REPLACE VVT SENSOR (Click here)
OK

REPLACE ECM (Click here)

78. CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


79. CHECK VVT SENSOR
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connectors.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (Click here)
OK


80. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


81. CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)
  1. Disconnect the VVT sensor (for intake camshaft) connectors.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B63-1 (VVR+) - B47-9 (VV1+)
    Always
    Below 1 Ω
    B63-2 (VVR-) - B47-10 (VV1-)
    Always
    Below 1 Ω
    B63-3 (VC) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B64-1 (VVL+) - B47-12 (VV2+)
    Always
    Below 1 Ω
    B64-2 (VVL-) - B47-11 (VV2-)
    Always
    Below 1 Ω
    B64-3 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B63-1 (VVR+) or B47-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B63-2 (VVR-) or B47-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B63-3 (VC) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B64-1 (VVL+) or B47-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B64-2 (VVL-) or B47-11 (VV2-) - Body ground
    Always
    10 kΩ or higher
    B64-3 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


82. CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM)
  1. Disconnect the VVT sensor (for exhaust camshaft) connectors.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) - B47-13 (EV1+)
    Always
    Below 1 Ω
    B57-2 (EX-) - B47-14 (EV1-)
    Always
    Below 1 Ω
    B57-3 (VC2) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B58-1 (EX+) - B47-18 (EV2+)
    Always
    Below 1 Ω
    B58-2 (EX-) - B47-17 (EV2-)
    Always
    Below 1 Ω
    B58-3 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) or B47-13 (EV1+) - Body ground
    Always
    10 kΩ or higher
    B57-2 (EX-) or B47-14 (EV1-) - Body ground
    Always
    10 kΩ or higher
    B57-3 (VC2) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B58-1 (EX+) or B47-18 (EV2+) - Body ground
    Always
    10 kΩ or higher
    B58-2 (EX-) or B47-17 (EV2-) - Body ground
    Always
    10 kΩ or higher
    B58-3 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


83. INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


84. INSPECT VVT SENSOR
  1. Inspect the VVT sensor.

HINT:
  1. For intake side of bank 1 or bank 2 (Click here).
  2. For exhaust side of bank 1 or bank 2 (Click here).



NG
REPLACE VVT SENSOR (Click here)
OK

REPLACE ECM (Click here)

85. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

  1. Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches should be off

Result 
Data List Item
Result
Suspected Area
Proceed to
ISC Learning Value
(engine displacement (liters) x 0.9) or more
  1. Valve timing
  2. Compression
A
Less than (engine displacement (liters) x 0.9)
-
B


B
Go to step 87
A


86. CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the compression (Click here).



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

CHECK VALVE TIMING (Click here)

87. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


88. CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures (Click here).

  1. Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

    Standard:
    Vehicle State
    Specified Condition
    Cranking engine
    304 to 343 kPa (3.1 to 3.5 kgf/cm2)
    5 minutes after stopping engine
    147 kPa (1.5 kgf/cm2) or more



NG
Go to step 94
OK


89. READ VALUE USING INTELLIGENT TESTER (LONG FT #1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    Long FT #2
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


90. PERFORM SIMULATION TEST
  1. Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


91. CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


92. INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


93. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

94. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 95
A

REPAIR OR REPLACE FUEL LINE

95. INSPECT FUEL PUMP
  1. Disconnect the fuel pump connector.

  1. A074356E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (+) - 5 (-)
    20°C (68°F)
    0.2 to 3.0 Ω

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.
Text in Illustration 
*1
Component without harness connected
(Fuel Pump)



NG
REPLACE FUEL PUMP (Click here)
OK

REPLACE PRESSURE REGULATOR ASSEMBLY (Click here)

96. CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures (Click here).

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    A
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    B



B
Go to step 102
A


97. READ VALUE USING INTELLIGENT TESTER (LONG FT #1 AND LONG FT #2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    Long FT #2
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


98. PERFORM SIMULATION TEST
  1. Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


99. CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


100. INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


101. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

102. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 103
A

REPAIR OR REPLACE FUEL LINE

103. INSPECT FUEL PUMP
  1. Disconnect the fuel pump connector.

  1. A074356E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (+) - 5 (-)
    20°C (68°F)
    0.2 to 3.0 Ω

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.
Text in Illustration 
*1
Component without harness connected
(Fuel Pump)



NG
REPLACE FUEL PUMP (Click here)
OK


104. INSPECT PURGE VSV

  1. A218155
    Disconnect the vacuum hose (on the canister side) of the purge VSV.

  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the connector of the purge VSV.

  1. Check if air flows through the purge VSV.

    OK:
    Air does not flow

  1. Connect the connector of the purge VSV.

  1. Connect the vacuum hose of the purge VSV.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
INSPECT PURGE VSV (Click here)
OK


105. CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B

    HINT:
    If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.



B
Go to step 106
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)

106. CHECK INTAKE VALVE
  1. Check if carbon is on the intake valves.

    Result 
    Result
    Proceed to
    Carbon present
    A
    No carbon present
    B



B
Go to step 107
A

CLEAN INTAKE VALVE

107. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

  1. Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

Result 
Data List Item
Result
Suspected Area
Proceed to
ISC Learning Value
(engine displacement (liters) x 0.9) or more
  1. Valve timing
  2. Compression
A
Less than (engine displacement (liters) x 0.9)
-
B


B
Go to step 109
A


108. CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the compression (Click here).



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

CHECK VALVE TIMING (Click here)

109. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


110. CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


111. CHECK VVT SENSOR
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connectors.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (Click here)
OK


112. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


113. CHECK AND REPLACE HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)
  1. Disconnect the VVT sensor (for intake camshaft) connectors.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B63-1 (VVR+) - B47-9 (VV1+)
    Always
    Below 1 Ω
    B63-2 (VVR-) - B47-10 (VV1-)
    Always
    Below 1 Ω
    B63-3 (VC) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B64-1 (VVL+) - B47-12 (VV2+)
    Always
    Below 1 Ω
    B64-2 (VVL-) - B47-11 (VV2-)
    Always
    Below 1 Ω
    B64-3 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B63-1 (VVR+) or B47-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B63-2 (VVR-) or B47-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B63-3 (VC) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B64-1 (VVL+) or B47-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B64-2 (VVL-) or B47-11 (VV2-) - Body ground
    Always
    10 kΩ or higher
    B64-3 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


114. CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM)
  1. Disconnect the VVT sensor (for exhaust camshaft) connectors.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) - B47-13 (EV1+)
    Always
    Below 1 Ω
    B57-2 (EX-) - B47-14 (EV1-)
    Always
    Below 1 Ω
    B57-3 (VC2) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B58-1 (EX+) - B47-18 (EV2+)
    Always
    Below 1 Ω
    B58-2 (EX-) - B47-17 (EV2-)
    Always
    Below 1 Ω
    B58-3 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) or B47-13 (EV1+) - Body ground
    Always
    10 kΩ or higher
    B57-2 (EX-) or B47-14 (EV1-) - Body ground
    Always
    10 kΩ or higher
    B57-3 (VC2) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B58-1 (EX+) or B47-18 (EV2+) - Body ground
    Always
    10 kΩ or higher
    B58-2 (EX-) or B47-17 (EV2-) - Body ground
    Always
    10 kΩ or higher
    B58-3 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


115. INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


116. INSPECT VVT SENSOR
  1. Inspect the VVT sensor.

HINT:
  1. For intake side of bank 1 or bank 2 (Click here).
  2. For exhaust side of bank 1 or bank 2 (Click here).



NG
REPLACE VVT SENSOR (Click here)
OK

REPLACE ECM (Click here)


← P1604 Startability Malfunction (Nov 2010 – Jul 2011)P1604 Startability Malfunction (Aug 2012 – Oct 2012) →