P1604 Startability Malfunction
Diagnostic trouble codes · Vehicles built Aug 2012 – Oct 2012
Versions by build date: Aug 2009 – Oct 2010 Nov 2010 – Jul 2011 Aug 2011 – Jul 2012 Aug 2012 – Oct 2012 Nov 2012 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1604 |
Either condition is met:
|
|
- *1: for Automatic Transmission Models
- *2: for Manual Transmission Models


| Reference waveforms showing a normal cold engine start |


| Reference waveforms showing a normal warm engine start |


| Reference waveforms showing an engine stop after normal idling |


| Reference values when there is an air leak in the intake system during starting difficulty |
| Current |
P1604: Startability Malfunction |
||||||
| Time Freeze Frame Data | |||||||
| Item |
Data1 |
Data2 |
Data3 |
Data4 |
Data5 |
Unit |
|
| Engine Speed |
1625 |
1042 |
501 |
192 |
129 |
rpm |
|
| Calculate Load |
43.1 |
30.5 |
38.8 |
93.3 |
93.3 |
% |
|
| Vehicle Load |
9.0 |
16.0 |
28.2 |
34.1 |
29.8 |
% |
|
| MAF |
6.01 |
6.67 |
5.64 |
2.62 |
1.54 |
gm/sec |
|
| Atmosphere Pressure |
95 |
95 |
95 |
95 |
95 |
kPa |
|
| Coolant Temp |
82 |
82 |
82 |
82 |
82 |
°C |
|
| Intake Air |
51 |
51 |
46 |
46 |
46 |
°C |
|
| Battery Voltage |
12.4 |
12.5 |
12.1 |
12.1 |
12.0 |
V |
|
| Throttle Sensor Volt % |
17.6 |
17.6 |
17.6 |
17.2 |
17.2 |
% |
|
| Throttle Sensor #2 Volt % |
50.1 |
50.1 |
50.1 |
49.8 |
49.8 |
% |
|
| Throttle Sensor Position |
0.0 |
0.0 |
0.0 |
0.0 |
0.0 |
% |
|
| Throttle Motor DUTY |
17.6 |
17.6 |
17.6 |
17.2 |
17.2 |
% |
|
| Injector (Port) |
3.77 |
2.45 |
2.90 |
3.24 |
7060 |
ms |
|
| Injection Volume (Cylinder 1) |
0.000 |
0.199 |
0.199 |
0.199 |
0.199 |
ml |
|
| Fuel Pump/Speed Status |
ON |
ON |
ON |
ON |
ON |
||
| EVAP (Purge) VSV |
0.0 |
0.0 |
0.0 |
0.0 |
0.0 |
% |
|
| Evap Purge Flow |
0.0 |
0.0 |
0.0 |
0.0 |
0.0 |
% |
|
| Purge Density Learn Value |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
||
| EVAP Purge VSV |
OFF |
OFF |
OFF |
OFF |
OFF |
||
| Purge Cut VSV Duty |
0.0 |
0.0 |
0.0 |
0.0 |
0.0 |
% |
|
| Target Air-Fuel Ratio |
0.889 |
0.913 |
0.920 |
0.925 |
0.833 |
||
| AF Lambda B1 S1 |
0.998 |
0.998 |
0.998 |
0.998 |
0.998 |
||
| AF Lambda B2 S1 |
0.998 |
0.998 |
0.998 |
0.998 |
0.998 |
||
| AFS Voltage B1 S1 |
3.29 |
3.29 |
3.29 |
3.29 |
3.29 |
V |
|
| AFS Voltage B2 S1 |
3.29 |
3.29 |
3.29 |
3.29 |
3.29 |
V |
|
| O2S B1 S2 |
0.00 |
0.00 |
0.00 |
0.00 |
0.00 |
V |
|
| O2S B2 S2 |
0.00 |
0.00 |
0.00 |
0.00 |
0.00 |
V |
|
| Short FT #1 |
0.0 |
0.0 |
0.0 |
0.0 |
0.0 |
% |
|
| Long FT #1 |
0.0 |
0.0 |
0.0 |
0.7 |
0.0 |
% |
|
| Total FT #1 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
||
| Short FT #2 |
0.0 |
0.0 |
0.0 |
0.0 |
0.0 |
% |
|
| Long FT #2 |
1.5 |
0.7 |
0.7 |
0.7 |
0.7 |
% |
|
| Total FT #2 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
||
| Fuel System Status #1 |
OL |
OL |
OL |
OL |
OL |
||
| Fuel System Status #2 |
OL |
OL |
OL |
OL |
OL |
||
| IGN Advance |
0.0 |
17.5 |
13.5 |
0.0 |
0.0 |
deg |
|
| Knock Feedback Value |
-3.0 |
-3.0 |
-3.0 |
-3.0 |
-3.0 |
CA |
|
| Knock Correct Learn Value |
23.1 |
23.1 |
23.1 |
23.1 |
23.1 |
CA |
|
| VVT Control Status #1 |
OFF |
OFF |
OFF |
OFF |
OFF |
||
| Starter Signal |
Close |
Close |
Close |
Close |
Close |
||
WIRING DIAGRAM






INSPECTION PROCEDURE
- HINT:
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
- If any other DTCs are output, perform troubleshooting for those DTCs first.
- When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
- Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
- When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here ).
- When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
- Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
- If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
- When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
- If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.
- In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
| Malfunction Recurrence and Inspection Areas |
Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.
The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).
- HINT:
- One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.
- If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.
- If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.
- If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or an ECM may be malfunctioning.


All engine speeds recorded in the freeze frame data are between 100 and 250 rpm (the engine cranks but there is no combustion).
- HINT:
- If the engine speed is between 100 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.
- Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.


The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).
- HINT:
- If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.
- Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
- If Long FT #1 is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.
- If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.


When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem symptoms" and "Systems to inspect")
Problem symptoms
- The engine does not crank.
- HINT:
- The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.
- The engine cranking speed is abnormal.
- HINT:
- If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.
- There is no initial combustion.
- HINT:
- If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.
- The engine stalls after starter turnoff.
- HINT:
- If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.
- The initial combustion and starter turnoff occur late.
- HINT:
- If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).
- HINT:
- Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
- When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
- When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
- When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.
- When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
- The engine does not crank.
Systems to inspect.
- Intake system
- Ignition system
- Fuel system
- Intake system
| INSPECTION FLOW |
Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.
Freeze Frame Data Item
Result
Suspected Area
Procedure
Engine Speed
0 rpm (no engine cranking at all)
- Battery fully depleted
- Engine assembly (excess friction)
- Starter
- Crankshaft position sensor
- ECM
4 to 9
100 to 250 rpm (engine cranks but no initial combustion*1)
- Fuel pump control system
- Ignition system
- Immobiliser system
- Engine coolant temperature sensor
- Fuel injection system
10 to 14
250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
- Engine assembly (compression loss)
- Fuel injection system
- Fuel pump control system
15 to 24
- HINT:
- *1: First combustion after cranking begins.
- *2: Condition when engine speed increases and starter can be turned off.
- *1: First combustion after cranking begins.
- Battery fully depleted
When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.
Problem symptoms
Problem Symptom
Suspected Area
Suspected Component
Procedure
The engine does not crank
Battery malfunction
- Battery fully depleted
26 to 31
Starting system
- Starter (includes pinion gear wear or tooth damage)
- Starting system
Engine assembly
- Engine assembly (excess friction)
- Drive plate wear or tooth damage
- Flywheel wear or tooth damage
Cranking speed too low
Battery malfunction
- Battery fully depleted
32 to 34
Starting system
- Starter
Engine assembly
- Engine assembly (excess friction)
Cranking speed too high
Engine assembly
- Engine assembly (compression loss)
There is no initial combustion
Fuel supply problem
- Cannot maintain pressure due to pressure regulator malfunction
- Fuel injector leak
- Fuel leak from fuel line
- Fuel pump control system
- Fuel pump
35 to 50
Immobiliser system
- Immobiliser system
Ignition system malfunction
- Spark plug
- Crankshaft position sensor
- Ignition coil
Engine stalls after starter turnoff
Air suction
- Intake system connections
51 to 57
Deposits in throttle body with motor assembly
- Throttle body with motor assembly
VVT valve does not return properly
- Camshaft timing oil control valve assembly
Mass air flow meter malfunction
- Mass air flow meter
The initial combustion and starter turnoff occur late
Engine coolant temperature sensor malfunction
- Engine coolant temperature sensor
58 to 71
Mass air flow meter malfunction
- Mass air flow meter
Abnormal A/F learning value
- Air fuel ratio sensor
Deviation from fuel injection characteristics
- Fuel injector assembly
Wet-fouled or dry-fouled spark plug
- Spark plug
Lack of fuel pressure
- Pressure regulator
- Fuel pump
- Fuel pump control system
- Battery fully depleted
Systems to inspect.
Troubleshooting by System
Suspected Area
Suspected Component
Procedure
Fuel system troubleshooting A
Abnormal A/F learning value
- Fuel injector assembly
88 to 95
96 to 103
Rough idling
- Crankshaft position sensor
Abnormal fuel pressure
- Fuel
- Fuel leak from fuel line
- Fuel pump
- Pressure regulator
Fuel system troubleshooting B
Abnormal concentration of HC in surge tank
- Purge VSV system
- Fuel injector assembly
104 to 106
Fuel system troubleshooting C
Injection signal system malfunction
- Fuel injector assembly
- Crankshaft position sensor
- VVT sensor
- ECM
73 to 77
Intake system troubleshooting
Difference between ISC target value and opening angle when idling
- Engine assembly (compression loss)
- Valve timing
- Engine coolant temperature sensor
- ECM
85 to 87
107 to 109
Ignition system troubleshooting
Camshaft and/or crankshaft position sensor signal malfunction
- Crankshaft position sensor system (including sensor installation)
- VVT sensor system (including sensor installation)
- ECM
78 to 84
110 to 116
- Fuel injector assembly
| 1. CHECK ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs and record the Freeze Frame Data.

- HINT:
- This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
- When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
- The fourth set of freeze frame data is the data recorded when then the DTC is stored.
- This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
Result Result
Proceed to
Only DTC P1604 is output
A
DTCs other than P1604 are output
B
|
|
||||
| A | |
| 2. CHECK ENGINE IMMOBILISER SYSTEM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Immobiliser Fuel Cut.
Read the value displayed on the intelligent tester.
- OK:
- Immobiliser Fuel Cut is OFF
- HINT:
- If the engine is cranked immediately after reconnecting the battery cable (key verification for immobiliser system not completed), the engine cannot be started. Key verification needs to wait for several seconds after turning the ignition switch to ON.
|
|
||||
| OK | |
| 3. CHECK MALFUNCTION CONDITION |
Confirm the problem symptoms.
Result Result
Proceed to
Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
A
The problem symptoms can be reproduced, or the malfunction conditions are known
B
|
|
||||
| A | |
| 4. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Suspected Area
Proceed to
Engine Speed
Battery Voltage
All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
Minimum voltage is less than 5 V
Battery fully depleted
A
Minimum voltage is 5 V or higher
- Starter malfunction
- Crankshaft position sensor system
- Excess engine friction
- ECM
B
60 to 250 rpm (engine cranks but no initial combustion)
-
- Fuel pump control system
- Ignition system
- Engine coolant temperature sensor
- Fuel injection system
C
250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
-
- Engine assembly
- Fuel injection system
- Fuel pump control system
D
- HINT:
- When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the Freeze Frame Data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
- *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
- *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
- Immobiliser Fuel Cut
- Engine Speed (Starter Off)
- Shift SW Status (R, D Range)
- Immobiliser Fuel Cut
- Starter malfunction
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 5. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Result
Suspected Area
Proceed to
Battery Voltage
Minimum voltage is 6 V or higher and voltage does not fluctuate*1
Starter system
A
Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
- Crankshaft position sensor system
- ECM
B
Minimum voltage is 5 to 6 V*4
- Excess engine friction
- Battery fully depleted
C
- HINT:
-
*1: The 5 sets of freeze frame data show approximately the same battery voltage.

- *2: The 5 sets of freeze frame data show different battery voltages.
- *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
- *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
-
- Crankshaft position sensor system
|
|
||||
|
|
||||
| A | ||
| ||
| 6. CHECK CRANKSHAFT POSITION SENSOR INSTALLATION |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
|
|
||||
| OK | |
| 7. CHECK CRANKSHAFT POSITION SENSOR |
Disconnect the crankshaft position sensor connector.
Check for oil on the connector terminals.
- OK:
- No oil on the terminals.
|
|
||||
| OK | |
| 8. INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B29 - B47-6 (NE+)
Always
Below 1 Ω
B29-1 - B47-5 (NE-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B29-1 or B47-6 (NE+) - Body ground
Always
10 kΩ or higher
B29-1 or B47-5 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 10. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Suspected Area
Proceed to
Coolant Temp, Ambient Temperature, Intake Air
Coolant Temp, Ambient Temperature
Fuel Pump/Speed Status
Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C or more*1
Coolant Temp is 125°C or more, or lower than Ambient Temperature by 15°C or more
-
Engine coolant temperature sensor
A
Other than above
All 5 sets of freeze frame data are ON
-
B
At least 1 of the 5 sets of freeze frame data is OFF
Fuel pump control system
C
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C*2
-
At least 1 of the 5 sets of freeze frame data is OFF
Fuel pump control system
C
All 5 sets of freeze frame data are ON
-
B
- HINT:
- *1: A long time had not elapsed after stopping the engine.
- *2: A long time had elapsed after stopping the engine.
- *1: A long time had not elapsed after stopping the engine.
|
|
||||
|
|
||||
| A | ||
| ||
| 11. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Disconnect the fuel pump connector.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
L5-4 - Body ground
Active Test is being performed
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Text in Illustration *1
Front view of wire harness connector
(to Fuel Pump)
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() ![]() |
Disconnect the injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B11-1 - Body ground
Ignition switch ON
11 to 14 V
B25-1 - Body ground
Ignition switch ON
11 to 14 V
B10-1 - Body ground
Ignition switch ON
11 to 14 V
B21-1 - Body ground
Ignition switch ON
11 to 14 V
B9-1 - Body ground
Ignition switch ON
11 to 14 V
B18-1 - Body ground
Ignition switch ON
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Text in Illustration *1
Front view of wire harness connector
(to Fuel Injector assedmbly)
|
|
||||
| OK | |
| 13. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 14. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is foreign matter or signs that fuel pump was stuck
A
There is no foreign matter and no signs that fuel pump was stuck
B
|
|
||||
| A | ||
| ||
| 15. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Suspected Area
Proceed to
Coolant Temp, Ambient Temperature, Intake Air
Coolant Temp, Ambient Temperature
Long FT #1
Long FT #2
Engine Speed
Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C or more
Coolant Temp is 125°C or more, or lower than Ambient Temperature by 15°C or more
-
-
Engine coolant temperature sensor
A
Other than above
-15% or less, or +15% or more
-
- Fuel pump control system
- Fuel injector assembly
B
-15 to +15%
Minimum speed is 300 rpm or more*1
Engine assembly
C
Minimum speed is below 300 rpm
- Fuel system
- Intake air system
D
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C
-
-15% or less, or +15% or more
-
- Fuel pump control system
- Fuel injector assembly
B
-15 to +15%
Minimum speed is 300 rpm or more*1
Engine assembly
C
Minimum speed is below 300 rpm
- Fuel system
- Intake air system
D
- HINT:
- *1: Compression loss may have occurred in the engine assembly.
- Fuel pump control system
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 16. INSPECT FUEL INJECTOR ASSEMBLY |
Check that no carbon is stuck to the fuel injector assembly.
- OK:
- No carbon present.
|
|
||||
| OK | |
| 17. CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
Result Result
Proceed to
There is foreign matter or signs that fuel pump was stuck
A
There is no foreign matter and no signs that fuel pump was stuck
B
|
|
||||
| A | ||
| ||
| 18. READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
Result Freeze Frame Data Item
Result
Suspected Area
Proceed to
Coolant Temp
Engine coolant temperature is 40°C (104°F) or less*1
Pressure regulator
A
Engine coolant temperature is 40 to 90°C (104 to 194°F)*2
Fuel injector assembly
B
Engine coolant temperature is 90°C (194°F) or more*3
Pressure regulator assembly
A
- HINT:
- *1: If the engine coolant temperature is 40°C (104°F) or less (after stopping the engine and the vehicle is not driven for a long period of time), the pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
- *2: If the engine coolant temperature is 40 to 90°C (104 to 194°F)(15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector.
- *3: If the engine coolant temperature is 90°C (194°F) or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator assembly failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
|
|
||||
| A | |
| 19. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
- Standard:
- 147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
- HINT:
- If the engine cannot be started, read the values after cranking the engine.
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | ||
| ||
| 20. CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
400 ppm or higher
A
Less than 400 ppm
B
- HINT:
- If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.
|
|
||||
| A | |
| 21. INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injectors (Click here).
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | ||
| ||
| 22. CHECK THROTTLE WITH MOTOR BODY ASSEMBLY |
Check if carbon is in the air flow passage.
Result Result
Proceed to
Carbon in passage
A
No carbon present
B
|
|
||||
| A | ||
| ||
| 23. CHECK INTAKE SYSTEM |
Check the intake system for vacuum leak (Click here).
- OK:
- No leak in intake system.
|
|
||||
| OK | |
| 24. PERFORM SIMULATION TEST |
Check if the engine can be started.
Result Result
Proceed to
Engine can be started
A
Engine cannot be started
B
|
|
||||
| A | ||
| ||
| 25. CONFIRM PROBLEM SYMPTOM |
Confirm the problem symptoms.
- HINT:
- The problem symptoms below can be determined by reading the freeze frame data.
Result Problem Symptom
Suspected Area
Proceed to
The engine does not crank
- Battery fully depleted
- Starter (includes pinion gear wear or teeth damage)
- Starter system
- Engine assembly (excess friction)
- Drive plate wear or teeth damage
- Flywheel wear or teeth damage
A
Abnormal cranking speed
- Battery fully depleted
- Starter
- Engine assembly (excess friction, compression loss)
B
There is no initial combustion (combustion does not occur even once)*1
- Pressure regulator fuel pressure maintenance
- Fuel injector leak
- Fuel leak from fuel line
- Fuel pump control system
- Fuel pump
- Spark plug
- Crankshaft position sensor system
- Ignition coil system
C
The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2
- Intake system connections
- Throttle with motor body assembly
- Camshaft timing oil control valve assembly
- Mass air flow meter system
D
The initial combustion and starter turnoff occur late*3
- Engine coolant temperature sensor
- Mass air flow meter
- Air fuel ratio sensor
- Fuel injector assembly
- Spark plug
- Pressure regulator assembly
- Fuel pump
- Fuel pump control system
E
- HINT:
- If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
- *1: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
- *2: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve assembly may have a problem returning.
- *3: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).
- If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 26. PERFORM SIMULATION TEST |
When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.
Result Problem Symptom
Suspected Area
Proceed to
A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely.*1
- Battery
- Excess engine friction
- Starter
A
A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely.
- Drive plate
- Flywheel
- Starter
B
A noise indicating that the starter pinion gear is extending is not heard
- Battery
- Starter
- Starter system
C
- HINT:
- *1: The battery may be fully depleted or there may be excess engine friction.
- Battery
|
|
||||
|
|
||||
| A | |
| 27. INSPECT BATTERY |
![]() ![]() |
Check the electrolyte quantity.
- OK:
- Electrolyte quantity is within the specified range.
Inspect the battery voltage.
Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.
Measure the battery voltage.
- Standard voltage:
- 12.5 to 12.9 V (electrolyte is at 20°C (68°F))
- HINT:
- If the result is not as specified, recharge or replace the battery.
Measure the battery voltage when cranking the engine.
- Standard voltage:
- Approximately 6 V or higher (0°C (32°F) or higher)
- HINT:
- When the battery is depleted, the horn becomes quieter.
|
|
||||
| OK | |
| 28. CHECK ENGINE ASSEMBLY |
Check that the crankshaft rotates smoothly when rotating it by hand.
- OK:
- Crankshaft rotates smoothly.
- HINT:
- Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
|
|
||||
| OK | ||
| ||
| 29. CHECK STARTER ASSEMBLY |
Remove the starter (Click here).
Check for starter pinion gear wear and damage.
- Standard:
- There is no wear or damage.
Result Result
Proceed to
NG
A
OK
(for Manual Transmission models)
B
OK
(for Automatic Transmission models)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 30. INSPECT BATTERY |
![]() ![]() |
Check the electrolyte quantity.
- OK:
- Electrolyte quantity is within the specified range.
Inspect the battery voltage.
Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.
Measure the battery voltage.
- Standard voltage:
- 12.5 to 12.9 V (electrolyte is at 20°C (68°F))
- HINT:
- If the result is not as specified, recharge or replace the battery.
Measure the battery voltage when cranking the engine.
- Standard voltage:
- Approximately 6 V or higher (0°C (32°F) or higher)
- HINT:
- When the battery is depleted, the horn becomes quieter.
|
|
||||
| OK | |
| 31. INSPECT STARTER ASSEMBLY |
Inspect the starter (Click here).
|
|
||||
| OK | ||
| ||
| 32. PERFORM SIMULATION TEST |
Check the cranking speed.
Result Problem Symptom
Suspected Area
Proceed to
Cranking speed is slow (100 rpm or less)
- Battery
- Starter
- Excess engine friction
A
Cranking speed is fast (300 rpm or more)*1
Engine compression loss
B
- HINT:
- *1: If the cranking speed is fast, there may be compression loss.
- Battery
|
|
||||
| A | |
| 33. INSPECT BATTERY |
![]() ![]() |
Check the electrolyte quantity.
- OK:
- Electrolyte quantity is within the specified range.
Inspect the battery voltage.
Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.
Measure the battery voltage.
- Standard voltage:
- 12.5 to 12.9 V (electrolyte is at 20°C (68°F))
- HINT:
- If the result is not as specified, recharge or replace the battery.
Measure the battery voltage when cranking the engine.
- Standard voltage:
- Approximately 6 V or higher (0°C (32°F) or higher)
- HINT:
- When the battery is depleted, the horn becomes quieter.
|
|
||||
| OK | |
| 34. CHECK ENGINE ASSEMBLY |
Check that the crankshaft rotates smoothly when rotating it by hand.
- OK:
- Crankshaft rotates smoothly.
- HINT:
- Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
|
|
||||
| OK | ||
| ||
| 35. CHECK FUEL INJECTOR ASSEMBLY |
Using a sound scope or screwdriver, check for an injector operating noise while cranking the engine.
- OK:
- Fuel injector operating noise is heard.
|
|
||||
| OK | |
| 36. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 37. INSPECT SPARK PLUG AND SPARK |
Inspect for sparks (Click here).
|
|
||||
| OK | |
| 38. CONFIRM VEHICLE CONDITION |
Confirm the conditions present when the malfunction occurred based on the customer problem analysis.
Result Problem Symptom
Suspected Area
Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1
Pressure regulator is stuck open
A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
Fuel injector leak
B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
Failure to maintain fuel pressure by pressure regulator assembly
A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
-
C*4
- HINT:
- *1: The pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
- *2: Fuel may be leaking from a fuel injector assembly.
- *3: The pressure regulator assembly may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
- *4: From step 72, perform fuel system troubleshooting C (steps 73 to 77).
|
|
||||
|
|
||||
| A | |
| 39. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result Result
Proceed to
Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
A
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
B*1
- HINT:
- If the engine cannot be started, check the fuel pressure after cranking the engine.
- *1: From step 72, perform fuel system troubleshooting C (steps 73 to 77).
- If the engine cannot be started, check the fuel pressure after cranking the engine.
|
|
||||
| A | ||
| ||
| 40. CHECK FUEL INJECTOR ASSEMBLY |
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
400 ppm or higher
A
Less than 400 ppm
B*1
- HINT:
- If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
- *1: From step 72, perform fuel system troubleshooting C (steps 73 to 77).
- If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
|
|
||||
| A | ||
| ||
| 41. INSPECT SPARK PLUG |
Inspect the spark plugs (Click here).
- HINT:
- Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.
|
|
||||
| OK | |
| 42. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
While running the engine, read the [Engine Speed] value.
- OK:
- A value that matches the actual engine speed is constantly output.
- HINT:
- Check the engine speed using a line graph.
- If the engine cannot be started, check the engine speed while cranking the engine.
- If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.
- Check the engine speed using a line graph.
|
|
||||
| OK | |
| 43. CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE) |
![]() ![]() |
Disconnect the ignition coil assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B7-1 (+B) - B7-4 (GND)
Ignition switch ON
11 to 14 V
B24-1 (+B) - B24-4 (GND)
Ignition switch ON
11 to 14 V
B6-1 (+B) - B6-4 (GND)
Ignition switch ON
11 to 14 V
B23-1 (+B) - B23-4 (GND)
Ignition switch ON
11 to 14 V
B5-1 (+B) - B5-4 (GND)
Ignition switch ON
11 to 14 V
B20-1 (+B) - B20-4 (GND)
Ignition switch ON
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Text in Illustration *1
Front view of wire harness connector
(to Ignition Coil Assembly)
|
|
||||
| OK | |
| 44. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM) |
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B7-2 (IGF) - B49-6 (IGF1)
Always
Below 1 Ω
B24-2 (IGF) - B49-6 (IGF1)
Always
Below 1 Ω
B6-2 (IGF) - B49-6 (IGF1)
Always
Below 1 Ω
B23-2 (IGF) - B49-6 (IGF1)
Always
Below 1 Ω
B5-2 (IGF) - B49-6 (IGF1)
Always
Below 1 Ω
B20-2 (IGF) - B49-6 (IGF1)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B7-2 (IGF) or B49-6 (IGF1) - Body ground
Always
10 kΩ or higher
B24-2 (IGF) or B49-6 (IGF1) - Body ground
Always
10 kΩ or higher
B6-2 (IGF) or B49-6 (IGF1) - Body ground
Always
10 kΩ or higher
B23-2 (IGF) or B49-6 (IGF1) - Body ground
Always
10 kΩ or higher
B5-2 (IGF) or B49-6 (IGF1) - Body ground
Always
10 kΩ or higher
B20-2 (IGF) or B49-6 (IGF1) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 45. CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM) |
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B7-3 (IGT1) - B49-24 (IGT1)
Always
Below 1 Ω
B24-3 (IGT2) - B49-25 (IGT2)
Always
Below 1 Ω
B6-3 (IGT3) - B49-26 (IGT3)
Always
Below 1 Ω
B23-3 (IGT4) - B49-27 (IGT4)
Always
Below 1 Ω
B5-3 (IGT5) - B49-28 (IGT5)
Always
Below 1 Ω
B20-3 (IGT6) - B48-25 (IGT6)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B7-3 (IGT1) or B49-24 (IGT1) - Body ground
Always
10 kΩ or higher
B24-3 (IGT2) or B49-25 (IGT2) - Body ground
Always
10 kΩ or higher
B6-3 (IGT3) or B49-26 (IGT3) - Body ground
Always
10 kΩ or higher
B23-3 (IGT4) or B49-27 (IGT4) - Body ground
Always
10 kΩ or higher
B5-3 (IGT5) or B49-28 (IGT5) - Body ground
Always
10 kΩ or higher
B20-3 (IGT6) or B48-25 (IGT6) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness is normal, after replacing the ignition coil, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform troubleshooting for the ignition system (steps 78 to 84).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 46. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
- OK:
Control the Fuel Pump / Speed
Specified Condition
ON
Operating sound heard
OFF
Operating sound not heard
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 47. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform fuel system troubleshooting (steps 73 to 77).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 48. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
While running the engine, read the [Engine Speed] value.
- OK:
- A value that matches the actual engine speed is constantly output.
- HINT:
- Check the engine speed using a line graph.
- If the engine cannot be started, check the engine speed while cranking the engine.
- If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.
- Check the engine speed using a line graph.
|
|
||||
| OK | |
| 49. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() ![]() |
Disconnect the injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B11-1 - Body ground
Ignition switch ON
11 to 14 V
B25-1 - Body ground
Ignition switch ON
11 to 14 V
B10-1 - Body ground
Ignition switch ON
11 to 14 V
B21-1 - Body ground
Ignition switch ON
11 to 14 V
B9-1 - Body ground
Ignition switch ON
11 to 14 V
B18-1 - Body ground
Ignition switch ON
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Text in Illustration *1
Front view of wire harness connector
(to Fuel Injector Assembly)
|
|
||||
| OK | |
| 50. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM) |
Disconnect the injector connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B11-2 - B50-6 (#10)
Always
Below 1 Ω
B25-2 - B50-1 (#20)
Always
Below 1 Ω
B10-2 - B50-7 (#30)
Always
Below 1 Ω
B21-2 - B50-2 (#40)
Always
Below 1 Ω
B9-2 - B50-8 (#50)
Always
Below 1 Ω
B18-2 - B50-3 (#60)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B11-2 or B50-6 (#10) - Body ground
Always
10 kΩ or higher
B25-2 or B50-1 (#20) - Body ground
Always
10 kΩ or higher
B10-2 or B50-7 (#30) - Body ground
Always
10 kΩ or higher
B21-2 or B50-2 (#40) - Body ground
Always
10 kΩ or higher
B9-2 or B50-8 (#50) - Body ground
Always
10 kΩ or higher
B18-2 or B50-3 (#60) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 51. INSPECT MASS AIR FLOW METER |
Inspect the mass air flow meter (Click here).
|
|
||||
| OK | |
| 52. CHECK INTAKE SYSTEM |
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).
- HINT:
- If the accelerator pedal is released after revving the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
- If Short FT and Long FT #1 are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when revving the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.
- If the accelerator pedal is released after revving the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
- OK:
- There is no air leakage.
|
|
||||
| OK | |
| 53. CHECK THROTTLE WITH MOTOR BODY ASSEMBLY |
Disconnect the throttle with motor body assembly connector.
- HINT:
- When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.
Crank the engine and check that it starts.
- HINT:
- When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).
Result Result
Proceed to
Engine starts
A
Engine does not start
B
|
|
||||
| A | |
| 54. CHECK THROTTLE WITH MOTOR BODY ASSEMBLY |
Check if carbon is in the air flow passage.
- OK:
- No carbon present.
|
|
||||
| OK | |
| 55. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT SYSTEM) |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
- HINT:
- When performing the Active Test, make sure the A/C is on and the shift lever is in N.
Check the engine speed while operating the Camshaft Timing Oil Control Valve (OCV) assembly using the tester.
- OK:
Tester Operation
Specified Condition
OCV OFF
Normal engine speed
OCV ON
Soon after OCV switched from OFF to ON, engine idles roughly or stalls
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 56. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR) |
Connect the intelligent tester to the DLC3.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
- HINT:
- When performing the Active Test, make sure the A/C is on and the shift lever is in N.
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
- OK*1:
Tester Operation
Specified Condition
0%
Normal engine speed
100%
Engine idles roughly or stalls
Result Result
Proceed to
NG
A
OK
B
- HINT:
- *1: From step 72, perform intake system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
- *1: From step 72, perform intake system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).
|
|
||||
| A | ||
| ||
| 57. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B51-5 (VG) - B48-14 (VG)
Always
Below 1 Ω
B51-4 (E2G) - B48-13 (E2G)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B51-5 (VG) or B48-14 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform intake system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 58. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
- HINT:
- If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
|
|
||||
| OK | |
| 59. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM) |
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B52-2 - B49-17 (THW)
Always
Below 1 Ω
B52-1 - B48-8 (ETHW)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B52-2 or B49-17 (THW) - Body ground
Always
10 kΩ or higher
B52-1 or B48-8 (ETHW) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 60. INSPECT MASS AIR FLOW METER |
Inspect the mass air flow meter (Click here).
- HINT:
- If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
|
|
||||
| OK | |
| 61. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B51-5 (VG) - B48-14 (VG)
Always
Below 1 Ω
B51-4 (E2G) - B48-13 (E2G)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B51-5 (VG) or B48-14 (VG) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 62. READ VALUE USING INTELLIGENT TESTER (LONG FT #1, FT #2 - ATMOSPHERE PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 /Long FT #2 and Atmosphere Pressure.
Result Data List Item
Result
Suspected Area
Proceed to
Long FT #1
Long FT #2
+25% or more or less than -25%
- Air fuel ratio sensor
- Mass air flow meter
- Fuel injector assembly
- ECM
A
Atmosphere Pressure
80 kPa or less (when altitude is 0 m)
Both Data List items listed above
Values are other than above
-
B
- Air fuel ratio sensor
|
|
||||
| A | |
| 63. PERFORM SIMULATION TEST |
Remove the EFI and ETCS fuses from the engine room relay block.
After 60 seconds or more elapse, install the EFI and ETCS fuses.
Check if the engine can be started.
Result Result
Proceed to
Engine can be started
A
Engine cannot be started
B
|
|
||||
| A | |
| 64. INSPECT AIR FUEL RATIO SENSOR |
![]() ![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1 and Fuel System Status #2.
Confirm that Fuel System Status #1 and Fuel System Status #2 are both CL.
Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1.
Confirm that AF Lambda B1S1 are both within the range of 0.95 to 1.05 when idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
- Standard:
Tester Display
Injection Volume
Specified Condition
AFS Voltage B1S1
AFS Voltage B2S1
+25%
Air fuel ratio sensor output voltage is below 3.1 V
-12.5%
Air fuel ratio sensor output voltage is higher than 3.4 V
- HINT:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
- If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
|
|
||||
| OK | |
| 65. PERFORM SIMULATION TEST |
Check if the idling speed is stable after starting the engine.
- OK:
- Speed is stable.
- HINT:
- After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
|
|
||||
| OK | ||
| ||
| 66. CHECK FUEL PRESSURE |
Check the fuel pressure (Click here).
|
|
||||
| OK | |
| 67. INSPECT SPARK PLUG |
Inspect the spark plugs (Click here).
Result Result
Proceed to
All cylinders are normal
A
One cylinder is abnormal*1
B
All cylinders are abnormal*2, *3
C
- HINT:
- *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.
- *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
|
|
||||
|
|
||||
| A | |
| 68. CONFIRM VEHICLE CONDITION |
Confirm the conditions present when the malfunction occurred based on the customer problem analysis.
Result Problem Symptom
Suspected Area
Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1
Pressure regulator assembly is stuck open
A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
Fuel injector leak
B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
Failure to maintain fuel pressure by pressure regulator
A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
-
C*4
- HINT:
- *1: The pressure regulator assembly may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
- *2: Fuel may be leaking from a fuel injector.
- *3: The pressure regulator assembly may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
- *4: From step 72, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
|
|
||||
|
|
||||
| A | |
| 69. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result Result
Proceed to
Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
A
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
B*1
- HINT:
- If the engine cannot be started, check the fuel pressure after cranking the engine.
- *1: From step 72, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- If the engine cannot be started, check the fuel pressure after cranking the engine.
|
|
||||
| A | ||
| ||
| 70. CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
400 ppm or higher
A
Less than 400 ppm
B*1
- HINT:
- If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
- *1: From step 72, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- If the concentration is 400 ppm or higher, a fuel injector may have a sealing problem.
|
|
||||
| A | ||
| ||
| 71. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 72. CHECK MALFUNCTION CONDITION |
If the malfunction could not be identified during the inspection in steps 38, 39, 40 and 47, perform fuel system troubleshooting C (steps 73 to 77).
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Steps 38, 39, 40 and 47
Fuel system troubleshooting C
73 to 77
A
If the malfunction could not be identified during the inspection in step 45, perform ignition system troubleshooting (steps 78 to 84).
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Step 45
Ignition system troubleshooting
78 to 84
B
If the malfunction could not be identified during the inspection in steps 55, 56 and 57, perform intake air system troubleshooting (steps 85 to 87). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 88 to 95).
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Step 55, 56, 57
Intake air system troubleshooting
85 to 87
C
Fuel system troubleshooting A
88 to 95
If the malfunction could not be identified during the inspection in steps 58, 59, 60, 63, 64, 65, 66, 67, 68, 69, 70 and 71, perform fuel system troubleshooting A (steps 96 to 103), fuel system troubleshooting B (steps 104 to 106), intake air system troubleshooting (steps 107 to 109), and ignition system troubleshooting (steps 110 to 116), in that order.
Result Performed Step
Troubleshooting by System
Procedure
Proceed to
Steps 58, 59, 60, 63, 64, 65, 66, 67, 68, 69, 70 and 71
Fuel system troubleshooting A
96 to 103
D
Fuel system troubleshooting B
104 to 106
Intake air system troubleshooting
107 to 109
Ignition system troubleshooting
110 to 116
|
|
||||
|
|
||||
|
|
||||
| A | |
| 73. INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injectors (Click here).
|
|
||||
| OK | |
| 74. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE) |
![]() ![]() |
Disconnect the injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
B11-1 - Body ground
Ignition switch ON
11 to 14 V
B25-1 - Body ground
Ignition switch ON
11 to 14 V
B10-1 - Body ground
Ignition switch ON
11 to 14 V
B21-1 - Body ground
Ignition switch ON
11 to 14 V
B9-1 - Body ground
Ignition switch ON
11 to 14 V
B18-1 - Body ground
Ignition switch ON
11 to 14 V
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Text in Illustration *1
Front view of wire harness connector
(to Fuel Injector)
|
|
||||
| OK | |
| 75. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM) |
Disconnect the injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B11-2 - B50-6 (#10)
Always
Below 1 Ω
B25-2 - B50-1 (#20)
Always
Below 1 Ω
B10-2 - B50-7 (#30)
Always
Below 1 Ω
B21-2 - B50-2 (#40)
Always
Below 1 Ω
B9-2 - B50-8 (#50)
Always
Below 1 Ω
B18-2 - B50-3 (#60)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B11-2 or B50-6 (#10) - Body ground
Always
10 kΩ or higher
B25-2 or B50-1 (#20) - Body ground
Always
10 kΩ or higher
B10-2 or B50-7 (#30) - Body ground
Always
10 kΩ or higher
B21-2 or B50-2 (#40) - Body ground
Always
10 kΩ or higher
B9-2 or B50-8 (#50) - Body ground
Always
10 kΩ or higher
B18-2 or B50-3 (#60) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 76. INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here ).
|
|
||||
| OK | |
| 77. INSPECT VVT SENSOR |
Inspect the VVT sensor.
- HINT:
- For intake side of bank 1 or bank 2 (Click here).
- For exhaust side of bank 1 or bank 2 (Click here).
- For intake side of bank 1 or bank 2 (Click here).
|
|
||||
| OK | ||
| ||
| 78. CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 79. CHECK VVT SENSOR |
Check the tightening and installation condition of the VVT sensor bolt.
Check the connection of the VVT sensor connectors.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 80. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B29-1 - B47-6 (NE+)
Always
Below 1 Ω
B29-2 - B47-5 (NE-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B29-1 or B47-6 (NE+) - Body ground
Always
10 kΩ or higher
B29-2 or B47-5 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 81. CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM) |
Disconnect the VVT sensor (for intake camshaft) connectors.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B63-1 (VVR+) - B47-9 (VV1+)
Always
Below 1 Ω
B63-2 (VVR-) - B47-10 (VV1-)
Always
Below 1 Ω
B63-3 (VC) - B47-15 (VCV1)
Always
Below 1 Ω
B64-1 (VVL+) - B47-12 (VV2+)
Always
Below 1 Ω
B64-2 (VVL-) - B47-11 (VV2-)
Always
Below 1 Ω
B64-3 (VC) - B47-16 (VCV2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B63-1 (VVR+) or B47-9 (VV1+) - Body ground
Always
10 kΩ or higher
B63-2 (VVR-) or B47-10 (VV1-) - Body ground
Always
10 kΩ or higher
B63-3 (VC) or B47-15 (VCV1) - Body ground
Always
10 kΩ or higher
B64-1 (VVL+) or B47-12 (VV2+) - Body ground
Always
10 kΩ or higher
B64-2 (VVL-) or B47-11 (VV2-) - Body ground
Always
10 kΩ or higher
B64-3 (VC) or B47-16 (VCV2) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 82. CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM) |
Disconnect the VVT sensor (for exhaust camshaft) connectors.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B57-1 (EX+) - B47-13 (EV1+)
Always
Below 1 Ω
B57-2 (EX-) - B47-14 (EV1-)
Always
Below 1 Ω
B57-3 (VC2) - B47-15 (VCV1)
Always
Below 1 Ω
B58-1 (EX+) - B47-18 (EV2+)
Always
Below 1 Ω
B58-2 (EX-) - B47-17 (EV2-)
Always
Below 1 Ω
B58-3 (VC2) - B47-16 (VCV2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B57-1 (EX+) or B47-13 (EV1+) - Body ground
Always
10 kΩ or higher
B57-2 (EX-) or B47-14 (EV1-) - Body ground
Always
10 kΩ or higher
B57-3 (VC2) or B47-15 (VCV1) - Body ground
Always
10 kΩ or higher
B58-1 (EX+) or B47-18 (EV2+) - Body ground
Always
10 kΩ or higher
B58-2 (EX-) or B47-17 (EV2-) - Body ground
Always
10 kΩ or higher
B58-3 (VC2) or B47-16 (VCV2) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 83. INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
|
||||
| OK | |
| 84. INSPECT VVT SENSOR |
Inspect the VVT sensor.
- HINT:
- For intake side of bank 1 or bank 2 (Click here).
- For exhaust side of bank 1 or bank 2 (Click here).
- For intake side of bank 1 or bank 2 (Click here).
|
|
||||
| OK | ||
| ||
| 85. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.
Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches should be off
| Data List Item |
Result |
Suspected Area |
Proceed to |
| ISC Learning Value |
(engine displacement (liters) x 0.9) or more |
|
A |
| Less than (engine displacement (liters) x 0.9) |
- |
B |
|
|
||||
| A | |
| 86. CHECK CYLINDER COMPRESSION PRESSURE |
Check the compression (Click here).
|
|
||||
| OK | ||
| ||
| 87. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
|
||||
| OK | |
| 88. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.
- Standard:
Vehicle State
Specified Condition
Cranking engine
304 to 343 kPa (3.1 to 3.5 kgf/cm2)
5 minutes after stopping engine
147 kPa (1.5 kgf/cm2) or more
|
|
||||
| OK | |
| 89. READ VALUE USING INTELLIGENT TESTER (LONG FT #1) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.
Result Data List Item
Result
Suspected Area
Proceed to
Long FT #1
Long FT #2
-15 to +15%
- Wire harness or connector
- Fuel
A
+15% or more, or less than -15%
Fuel injector assembly
B
- Wire harness or connector
|
|
||||
| A | |
| 90. PERFORM SIMULATION TEST |
Check if the idling speed after starting the engine is currently stable and has always been stable in the past.
Result Problem Symptom
Suspected Area
Proceed to
Current unstable idling speed or history of unstable idling speed
Crankshaft position sensor system
A
All current and past idling speeds are stable
Fuel
B
- HINT:
- Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.
|
|
||||
| A | |
| 91. CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 92. INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
|
||||
| OK | |
| 93. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B29-1 - B47-6 (NE+)
Always
Below 1 Ω
B29-2 - B47-5 (NE-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B29-1 or B47-6 (NE+) - Body ground
Always
10 kΩ or higher
B29-2 or B47-5 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 94. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 95. INSPECT FUEL PUMP |
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (+) - 5 (-)
20°C (68°F)
0.2 to 3.0 Ω
- HINT:
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
- Make sure the internal connector is securely connected.
- Make sure the fuel pump filter is not clogged.
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
Text in Illustration *1
Component without harness connected
(Fuel Pump)
|
|
||||
| OK | ||
| ||
| 96. CHECK FUEL PRESSURE |
- HINT:
- For the fuel pressure inspection, refer to the following procedures (Click here).
Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
Result Result
Proceed to
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
A
Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
B
|
|
||||
| A | |
| 97. READ VALUE USING INTELLIGENT TESTER (LONG FT #1 AND LONG FT #2) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.
Result Data List Item
Result
Suspected Area
Proceed to
Long FT #1
Long FT #2
-15 to +15%
- Wire harness or connector
- Fuel
A
+15% or more, or less than -15%
Fuel injector assembly
B
- Wire harness or connector
|
|
||||
| A | |
| 98. PERFORM SIMULATION TEST |
Check if the idling speed after starting the engine is currently stable and has always been stable in the past.
Result Problem Symptom
Suspected Area
Proceed to
Current unstable idling speed or history of unstable idling speed
Crankshaft position sensor system
A
All current and past idling speeds are stable
Fuel
B
- HINT:
- Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.
|
|
||||
| A | |
| 99. CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 100. INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
|
||||
| OK | |
| 101. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B29-1 - B47-6 (NE+)
Always
Below 1 Ω
B29-2 - B47-5 (NE-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B29-1 or B47-6 (NE+) - Body ground
Always
10 kΩ or higher
B29-2 or B47-5 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | ||
| ||
| 102. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.
When performing the Active Test, check for fuel leakage from the fuel pipes.
Result Result
Proceed to
Fuel leakage or signs of fuel leakage are present
A
No fuel leakage or signs of fuel leakage
B
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
- Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| A | ||
| ||
| 103. INSPECT FUEL PUMP |
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (+) - 5 (-)
20°C (68°F)
0.2 to 3.0 Ω
- HINT:
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
- Make sure the internal connector is securely connected.
- Make sure the fuel pump filter is not clogged.
- Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
Text in Illustration *1
Component without harness connected
(Fuel Pump)
|
|
||||
| OK | |
| 104. INSPECT PURGE VSV |
Disconnect the vacuum hose (on the canister side) of the purge VSV.

Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
- OK:
- Air does not flow
Connect the connector of the purge VSV.
Connect the vacuum hose of the purge VSV.
- HINT:
- When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).
|
|
||||
| OK | |
| 105. CHECK FUEL INJECTOR ASSEMBLY |
Clean the inside of the surge tank with compressed air.
After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
Result Result
Proceed to
400 ppm or higher
A
Less than 400 ppm
B
- HINT:
- If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.
|
|
||||
| A | ||
| ||
| 106. CHECK INTAKE VALVE |
Check if carbon is on the intake valves.
Result Result
Proceed to
Carbon present
A
No carbon present
B
|
|
||||
| A | ||
| ||
| 107. READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
| Data List Item |
Result |
Suspected Area |
Proceed to |
| ISC Learning Value |
(engine displacement (liters) x 0.9) or more |
|
A |
| Less than (engine displacement (liters) x 0.9) |
- |
B |
|
|
||||
| A | |
| 108. CHECK CYLINDER COMPRESSION PRESSURE |
Check the compression (Click here).
|
|
||||
| OK | ||
| ||
| 109. INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
|
||||
| OK | |
| 110. CHECK CRANKSHAFT POSITION SENSOR |
Check the tightening and installation condition of the crankshaft position sensor bolt.
Check the connection of the crankshaft position sensor connector.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 111. CHECK VVT SENSOR |
Check the tightening and installation condition of the VVT sensor bolt.
Check the connection of the VVT sensor connectors.
- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 112. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) |
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B29-1 - B47-6 (NE+)
Always
Below 1 Ω
B29-2 - B47-5 (NE-)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B29-1 or B47-6 (NE+) - Body ground
Always
10 kΩ or higher
B29-2 or B47-5 (NE-) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 113. CHECK AND REPLACE HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM) |
Disconnect the VVT sensor (for intake camshaft) connectors.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B63-1 (VVR+) - B47-9 (VV1+)
Always
Below 1 Ω
B63-2 (VVR-) - B47-10 (VV1-)
Always
Below 1 Ω
B63-3 (VC) - B47-15 (VCV1)
Always
Below 1 Ω
B64-1 (VVL+) - B47-12 (VV2+)
Always
Below 1 Ω
B64-2 (VVL-) - B47-11 (VV2-)
Always
Below 1 Ω
B64-3 (VC) - B47-16 (VCV2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B63-1 (VVR+) or B47-9 (VV1+) - Body ground
Always
10 kΩ or higher
B63-2 (VVR-) or B47-10 (VV1-) - Body ground
Always
10 kΩ or higher
B63-3 (VC) or B47-15 (VCV1) - Body ground
Always
10 kΩ or higher
B64-1 (VVL+) or B47-12 (VV2+) - Body ground
Always
10 kΩ or higher
B64-2 (VVL-) or B47-11 (VV2-) - Body ground
Always
10 kΩ or higher
B64-3 (VC) or B47-16 (VCV2) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 114. CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM) |
Disconnect the VVT sensor (for exhaust camshaft) connectors.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
B57-1 (EX+) - B47-13 (EV1+)
Always
Below 1 Ω
B57-2 (EX-) - B47-14 (EV1-)
Always
Below 1 Ω
B57-3 (VC2) - B47-15 (VCV1)
Always
Below 1 Ω
B58-1 (EX+) - B47-18 (EV2+)
Always
Below 1 Ω
B58-2 (EX-) - B47-17 (EV2-)
Always
Below 1 Ω
B58-3 (VC2) - B47-16 (VCV2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
B57-1 (EX+) or B47-13 (EV1+) - Body ground
Always
10 kΩ or higher
B57-2 (EX-) or B47-14 (EV1-) - Body ground
Always
10 kΩ or higher
B57-3 (VC2) or B47-15 (VCV1) - Body ground
Always
10 kΩ or higher
B58-1 (EX+) or B47-18 (EV2+) - Body ground
Always
10 kΩ or higher
B58-2 (EX-) or B47-17 (EV2-) - Body ground
Always
10 kΩ or higher
B58-3 (VC2) or B47-16 (VCV2) - Body ground
Always
10 kΩ or higher
- HINT:
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
- Make sure there is not an excessive amount of force applied to the wire harness.
- Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
|
|
||||
| OK | |
| 115. INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
|
||||
| OK | |
| 116. INSPECT VVT SENSOR |
Inspect the VVT sensor.
- HINT:
- For intake side of bank 1 or bank 2 (Click here).
- For exhaust side of bank 1 or bank 2 (Click here).
- For intake side of bank 1 or bank 2 (Click here).
|
|
||||
| OK | ||
| ||






