When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal depressed.
| Problem Symptom | Data List and Active Test |
|---|---|
| Engine does not start |
Power Source Control
·
Stop Light Switch
·
Shift P Signal
·
Neutral SW/ Clutch SW
·
Starter Relay Driving Request (Starting Control)
·
Starter Relay
·
Power Supply Condition
Entry&Start
·
Immobiliser
·
Start Request
·
L Code Check
·
S Code Check |
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.
After completing repairs, confirm that the problem does not recur.
After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
If the ignition switch is changed from ON to ACC with the shift lever in any position other than P, and then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the ignition switch will turn off.
If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure will be released and the force required to depress the brake pedal to illuminate the stop lights will increase.
Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.
Check that the engine can be started 5 seconds after the ignition switch turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.
The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.
The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, check if LIN communication DTC B278588 and B278987 are output.
DTC B278588 and B278987 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch and check that the engine cranks.
| Result | Proceed to |
|---|---|
| Engine cranks and initial combustion occurs | A |
| Engine cranks but initial combustion does not occur | B |
| Engine does not crank | C |
A
B
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P.
With the brake pedal released, check that pressing the engine switch causes the power source mode to change.
| Result | Proceed to |
|---|---|
| Power source mode changes : Off → ACC → ON → off | A |
| Power source mode does not change to ACC or ON | B |
| Power source mode changes to ON but not to ACC | C |
| Power source mode changes to ACC but not to ON | D |
A
B
C
D
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch | State of brake pedal | OFF or ON | OFF: Brake pedal released ON: Brake pedal depressed |
·
Use this item to determine if the stop light switch assembly is malfunctioning.
·
The engine cannot be started when this item is OFF.
·
If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch |
The GTS display changes correctly in response to the brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position P | OFF or ON | OFF: Shift lever not in P ON: Shift lever in P |
·
Use this item to determine if the shift position switch is malfunctioning.
·
The engine cannot be started when this item is OFF. |
| Tester Display |
|---|
| Shift P Signal |
The GTS display changes correctly in response to the shift lever operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | Shift position (P and N) | OFF or ON | OFF: Shift lever in any position other than P or N ON: Shift lever in P or N |
·
Use this item to determine if the park/neutral position switch assembly is malfunctioning.
·
When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Park/Neutral position switch status | OFF or ON | OFF: Shift lever not in P or N ON: Shift lever in P or N |
When OFF is displayed, the engine will not crank. |
| Tester Display |
|---|
| Shift Position P or N |
The GTS display changes correctly in response to the shift lever operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | OFF, ACC ON, IGR ON, IGP ON or Starter ON | OFF: Ignition switch off ACC ON: Ignition switch ACC IGR ON: Ignition switch ON IGP ON: Ignition switch ON Starter ON: Sending engine start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.
The GTS display changes correctly in response to the engine switch operation.
| Proceed to |
|---|
| OK (w/ Stop and Start System) |
| OK (w/o Stop and Start System) |
| NG |
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly (ST NO. 1 Relay Holder) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 2 - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1.0 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly (ST NO. 1 Relay Holder) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C52 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C52)Location & Routingewd_type=routing;type=c;code=C52 |
||
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 3 - C52-2 (ST) | Always | Below 1 Ω |
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 3 or C52-2 (ST) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Engine Room Relay Block and No. 1 Junction Block Assembly (ST No. 2 Relay Holder) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 2 engine room relay block and No. 2 junction block assembly ST No. 2 relay terminal 2 - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1.0 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and No. 2 Junction Block Assembly (ST NO. 2 Relay Holder) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 1 - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C52 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C52)Location & Routingewd_type=routing;type=c;code=C52 |
||
| No. 1 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 3 - C52-1 (SL2) | Always | Below 1 Ω |
| No. 1 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 3 or C52-1 (SL2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I40 certification ECU (smart key ECU assembly) connector.
Disconnect the B43 stop light switch assembly connector.
Disconnect the B2*1, B1*2 ECM connector.
*1: for 1GR-FE
*2: for V35A-FTS
Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the I35 shift lock control unit assembly connector.
Disconnect the C36 transmission control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I40,B43)Location & Routingewd_type=routing;type=c,c;code=I40,B43 Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assemblyewd_type=component;type=c;code=B43;pinno=3 |
||
| I40-21 (STP1) - B43-3 (L) | Always | Below 1 Ω |
| I40-21 (STP1) or B43-3 (L) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I39)Location & Routingewd_type=routing;type=c;code=I39 |
||
| I39-14 (P) - Body ground | Shift lever in P → Shift lever not in P | 9 V or higher → 2.76 V or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B2*1, B1*2 ECM connector.
*1: for 1GR-FE
*2: for V35A-FTS
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Switch / Clutch Switch | Shift position (P and N) | OFF or ON | OFF: Shift lever in any position other than P or N ON: Shift lever in P or N |
·
Use this item to determine if the park/neutral position switch assembly is malfunctioning.
·
When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral Switch / Clutch Switch |
The GTS display changes correctly in response to the shift lever operation.
| Proceed to |
|---|
| OK |
| NG (w/ Stop and Start System) |
| NG (w/o Stop and Start System) |
OK
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>ECM>REMOVAL
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)
Disconnect the I39 certification ECU (smart key ECU assembly) connector.
Disconnect the I35 shift lock control unit assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I39,I35)Location & Routingewd_type=routing;type=c,c;code=I39,I35 |
||
| I39-14 (P) - I35-1 (P2) | Always | Below 1 Ω |
| I39-14 (P) or I35-1 (P2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for AC60F:
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>REMOVAL
for AJA0F:
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>REMOVAL
NG
Disconnect the B38 engine stop and start ECU connector.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Switch / Clutch Switch | Shift position (P and N) | OFF or ON | OFF: Shift lever in any position other than P or N ON: Shift lever in P or N |
·
Use this item to determine if the park/neutral position switch assembly is malfunctioning.
·
When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral Switch / Clutch Switch |
The GTS display changes correctly in response to the shift lever operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34)Location & Routingewd_type=routing;type=c;code=C34 |
||
| C34-5 (L) - No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| C34-5 (L) or No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B38 engine stop and start ECU connector.
Disconnect the B1 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38,B1)Location & Routingewd_type=routing;type=c,c;code=B38,B1 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=23 |
||
| ST NO. 2 relay installation terminal 2 - B38-23 (STA2) | Always | Below 1 Ω |
| ST NO. 2 relay installation terminal 2 - B1-34 (STA) | Always | Below 1 Ω |
| ST NO. 2 relay installation terminal 2 or B38-23 (STA2) - Other terminals and body ground | Always | 10 kΩ or higher |
| ST NO. 2 relay installation terminal 2 or B1-34 (STA) - Other terminals and body ground | Always | 10 kΩ or higher |
Connect the B1 ECM connector.
Install the ST NO. 2 relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected (Engine Stop and Start ECU) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(B38)Location & Routingewd_type=routing;type=c;code=B38 Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECUewd_type=component;type=c;code=B38;pinno=23 |
||
| B38-23 (STA2) - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for AC60F:
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for AJA0F:
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for AC60F:
Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for AJA0F:
Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the I40 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I40,C34)Location & Routingewd_type=routing;type=c,c;code=I40,C34 |
||
| I40-10 (STAR) - C34-4 (B) | Always | Below 1 Ω |
| I40-10 (STAR) or C34-4 (B) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (STARTING)>RELAY>ON-VEHICLE INSPECTION
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly (ST NO. 1 Relay Holder) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 2 - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) | 6 V or higher* → 1.0 V or less |
*: While the engine is cranking, the battery voltage may drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly (ST NO. 1 Relay Holder) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C101*1, C52*2 starter assembly connector.
*1: for 1GR-FE
*2: for V35A-FTS
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C101)Location & Routingewd_type=routing;type=c;code=C101 |
||
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 3 - C101-1 (ST) | Always | Below 1 Ω |
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 3 or C101-1 (ST) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C52)Location & Routingewd_type=routing;type=c;code=C52 |
||
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 3 - C52-2 (ST) | Always | Below 1 Ω |
| No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 3 or C52-2 (ST) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 1GR-FE
*2: for V35A-FTS
Disconnect the C99*1, C56*2 starter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C99,C56)Location & Routingewd_type=routing;type=c,c;code=C99,C56 |
||
| C99-1 - Body ground*1 | Always | 11 to 14 V |
| C56-1 - Body ground*2 | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (STARTING)>STARTER>REMOVAL
for V35A-FTS:
Click hereEngine / Hybrid System>V35A-FTS (STARTING)>STARTER (w/o Stop And Start System)>REMOVAL
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(C34)Location & Routingewd_type=routing;type=c;code=C34 |
||
| C34-5 (L) - No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| C34-5 (L) or No. 1 engine room relay block and No. 1 junction block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the steering unlocks when the ignition switch is turned to ACC.
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG