Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch

·

Shift P Signal

·

Neutral SW/ Clutch SW

·

Starter Relay Driving Request (Starting Control)

·

Starter Relay

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Start Request

·

L Code Check

·

S Code Check



WIRING DIAGRAM

for Gasoline


B616493E03
5.938,0.51 6.396,0.708 0.458,0.198 10 false STP 5.938,2.208 6.396,2.406 0.458,0.198 10 false P2 5.417,0.854 5.875,1.052 0.458,0.198 10 false C36 5.417,1.021 7.104,1.406 1.688,0.385 10 false Transmission Control ECU 5.646,0.396 6.104,0.594 0.458,0.198 10 false 36 5.719,2.208 6.177,2.406 0.458,0.198 10 false 1 5.615,2.531 6.073,2.729 0.458,0.198 10 false I35 5.604,2.74 7.021,3.167 1.417,0.427 10 false Shift Lock Control Unit Assembly 5.583,3.667 6.042,3.865 0.458,0.198 10 false 14 5.594,4.177 6.052,4.375 0.458,0.198 10 false 21 5.573,3.896 6.031,4.094 0.458,0.198 10 false I39 5.583,4.396 6.042,4.594 0.458,0.198 10 false I40 5.917,4.271 6.375,4.469 0.458,0.198 10 false STP1 5.948,3.896 6.406,4.094 0.458,0.198 10 false P 6.583,4.469 7.042,4.667 0.458,0.198 10 false IC 5.542,5.125 7.073,5.552 1.531,0.427 10 false Certification ECU (Smart Key ECU Assembly) 1.375,0.396 1.833,0.594 0.458,0.198 10 false 37 1.375,1.813 2.219,2.052 0.844,0.24 10 false 7*1, 22*2 0.125,0.833 0.583,1.031 0.458,0.198 10 false B20 0.104,1.021 3.531,1.573 3.427,0.552 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 0.656,2.552 1.865,2.969 1.208,0.417 10 false ECM 0.521,2.302 1.552,2.594 1.031,0.292 10 false B2*1, B1*2 0.917,0.51 1.438,0.708 0.521,0.198 10 false STP2 0.979,1.938 1.438,2.135 0.458,0.198 10 false STP 0.313,4.146 1.198,4.625 0.885,0.479 10 false from Battery 1.656,4.333 2.115,4.531 0.458,0.198 10 false STOP 2.156,4.052 2.615,4.25 0.458,0.198 10 false 7 2.156,4.417 2.615,4.615 0.458,0.198 10 false 2 2.354,4.188 2.813,4.385 0.458,0.198 10 false B 2.344,4.542 2.802,4.74 0.458,0.198 10 false GND 2.781,4.385 3.24,4.583 0.458,0.198 10 false IC 3.115,4.281 3.573,4.479 0.458,0.198 10 false L 3.302,4.281 3.76,4.479 0.458,0.198 10 false 3 2.094,4.938 2.552,5.135 0.458,0.198 10 false B43 2.083,5.104 4.344,5.448 2.26,0.344 10 false Stop Light Switch Assembly 0.198,5.031 2.458,5.375 2.26,0.344 10 false *1: for 1GR-FE 0.188,5.406 2.448,5.75 2.26,0.344 10 false *2: for V35A-FTS

w/ Stop and Start System:
B612584E01
5.26,5.927 6.615,6.229 1.354,0.302 10 false Starter Assembly 0.531,3.156 1.885,3.458 1.354,0.302 10 false ECM 0.531,2.99 1.885,3.292 1.354,0.302 10 false B1 4.323,1.865 5.698,2.375 1.375,0.51 10 false Park/Neutral Position Switch Assembly 4.313,1.708 5.688,2.219 1.375,0.51 10 false C34 5.573,3.052 7.073,3.594 1.5,0.542 10 false Certification ECU (Smart Key ECU Assembly) 0.094,7.219 2.177,7.833 2.083,0.615 10 false Engine Stop and Start ECU 0.094,7.063 2.177,7.677 2.083,0.615 10 false B38 3.448,5.583 4.375,6.427 0.927,0.844 10 false ST NO. 2 3.438,3.104 4.365,3.948 0.927,0.844 10 false ST NO. 1 3.417,4.094 4.344,4.938 0.927,0.844 10 false ST NO. 1 3.458,4.594 4.385,5.438 0.927,0.844 10 false ST NO. 2 6.188,3.74 7.115,4.583 0.927,0.844 10 false from Battery 3.833,1.469 5.208,1.979 1.375,0.51 10 false B 4.115,1.469 5.49,1.979 1.375,0.51 10 false L 3.583,2.021 4.958,2.531 1.375,0.51 10 false N 3.583,1.771 4.958,2.281 1.375,0.51 10 false P 5.563,2.896 7.063,3.438 1.5,0.542 10 false I40 5.542,0.833 6.292,1.521 0.75,0.688 10 false 10 5.813,0.813 6.563,1.5 0.75,0.688 10 false STAR 5.823,2.438 6.573,3.125 0.75,0.688 10 false STA 5.594,2.344 6.344,3.031 0.75,0.688 10 false 3 6.49,1.094 7.063,1.833 0.573,0.74 10 false IC 3.74,1.219 4.49,1.906 0.75,0.688 10 false 4 4.031,2.281 4.781,2.969 0.75,0.688 10 false 5 0.865,2.448 2.219,2.75 1.354,0.302 10 false STA 0.833,0.917 2.188,1.219 1.354,0.302 10 false NSW 1.26,0.813 2.615,1.115 1.354,0.302 10 false 7 1.26,2.313 2.615,2.615 1.354,0.302 10 false 34 0.792,5.313 2.146,5.615 1.354,0.302 10 false STA2 1.26,5.219 2.615,5.521 1.354,0.302 10 false 23 0.875,6.438 2.229,6.74 1.354,0.302 10 false STA 1.229,6.323 2.583,6.625 1.354,0.302 10 false 21 1.26,4.167 2.615,4.469 1.354,0.302 10 false 17 0.885,4.281 2.24,4.583 1.354,0.302 10 false CLL 3.365,3.438 4.115,4.125 0.75,0.688 10 false 5 4,3.438 4.75,4.125 0.75,0.688 10 false 3 4.052,4.906 4.802,5.594 0.75,0.688 10 false 3 3.375,4.896 4.125,5.583 0.75,0.688 10 false 5 3.365,3.719 4.115,4.406 0.75,0.688 10 false 2 3.375,5.219 4.125,5.906 0.75,0.688 10 false 2 4.052,5.219 4.802,5.906 0.75,0.688 10 false 1 4,3.729 4.75,4.417 0.75,0.688 10 false 1 4.927,5.052 6.281,5.354 1.354,0.302 10 false C52 5,4.865 6.354,5.167 1.354,0.302 10 false 1 5.292,5.042 6.646,5.344 1.354,0.302 10 false SL2 4.927,5.563 6.281,5.865 1.354,0.302 10 false C52 5.021,5.375 5.771,6.063 0.75,0.688 10 false 2 5.292,5.542 6.646,5.844 1.354,0.302 10 false ST 6.479,5.042 7.094,5.5 0.615,0.458 10 false C56 6.25,5.052 6.865,5.51 0.615,0.458 10 false B 6.552,4.854 7.094,5.292 0.542,0.438 10 false 1

w/o Stop and Start System:
B616494E01
6.573,0.875 6.885,1.073 0.313,0.198 10 false IC 5.906,0.792 6.365,1.021 0.458,0.229 10 false STAR 6.25,0.406 6.563,0.604 0.313,0.198 10 false +B 5.615,0.781 5.927,0.979 0.313,0.198 10 false 10 5.677,3.26 5.99,3.458 0.313,0.198 10 false 3 5.938,3.375 6.396,3.604 0.458,0.229 10 false STA 5.563,3.635 6.021,3.865 0.458,0.229 10 false I40 5.531,3.823 7.063,4.26 1.531,0.438 10 false Certification ECU (Smart Key ECU Assembly) 5.969,5.563 6.844,6.063 0.875,0.5 10 false from Battery 4.479,5.521 4.792,5.719 0.313,0.198 10 false C56 4.531,5.302 4.844,5.5 0.313,0.198 10 false 1 3.74,4.885 4.052,5.083 0.313,0.198 10 false 1 3.313,4.896 3.885,5.094 0.573,0.198 10 false C101 3.563,5.375 3.875,5.573 0.313,0.198 10 false ST 3.115,6.125 4.458,6.521 1.344,0.396 10 false Starter Assembly 4.24,5.406 4.552,5.604 0.313,0.198 10 false B 4.167,3.719 4.927,4 0.76,0.281 10 false ST NO.1 3.667,4.01 4.427,4.292 0.76,0.281 10 false ST NO.1 3.083,4.344 3.396,4.542 0.313,0.198 10 false 1 3.333,4.354 3.646,4.552 0.313,0.198 10 false 3 3.104,3.625 3.417,3.823 0.313,0.198 10 false 2 3.344,3.625 3.656,3.823 0.313,0.198 10 false 5 3.063,2.667 3.375,2.865 0.313,0.198 10 false 5 2.875,1.865 3.031,2.083 0.156,0.219 10 false B 3.177,1.875 3.333,2.094 0.156,0.219 10 false L 2.615,2.135 2.771,2.354 0.156,0.219 10 false P 2.594,2.406 2.75,2.625 0.156,0.219 10 false N 2.813,1.573 3.125,1.771 0.313,0.198 10 false 4 1.354,0.771 2.5,1.042 1.146,0.271 10 false 48*1, 7*2 1.375,3.229 2.677,3.531 1.302,0.302 10 false 16*1, 34*2 0.99,3.333 1.448,3.563 0.458,0.229 10 false STA 0.906,0.802 1.365,1.031 0.458,0.229 10 false NSW 0.479,3.823 1.75,4.104 1.271,0.281 10 false B2*1, B1*2 0.604,4.031 1.219,4.573 0.615,0.542 10 false ECM 3.417,2.021 3.875,2.25 0.458,0.229 10 false C34 3.427,2.271 4.74,2.823 1.313,0.552 10 false Park/Neutral Position Switch Assembly 0.417,5.479 1.958,6.01 1.542,0.531 10 false *1: for 1GR-FE 0.417,5.948 1.958,6.479 1.542,0.531 10 false *2: for V35A-FTS 3.344,5.125 3.917,5.323 0.573,0.198 10 false C52 3.74,5.125 4.052,5.323 0.313,0.198 10 false 2 4.854,5.521 5.167,5.719 0.313,0.198 10 false C99 3.094,4.885 3.667,5.083 0.573,0.198 10 false *1 4.906,5.74 5.479,5.938 0.573,0.198 10 false *1 4.521,5.74 5.094,5.938 0.573,0.198 10 false *2 3.104,5.104 3.677,5.302 0.573,0.198 10 false *2 4.948,5.313 5.26,5.51 0.313,0.198 10 false 1


for Diesel


B616493E04
5.938,0.51 6.396,0.708 0.458,0.198 10 false STP 5.938,2.208 6.396,2.406 0.458,0.198 10 false P2 5.417,0.854 5.875,1.052 0.458,0.198 10 false C36 5.417,1.021 7.104,1.406 1.688,0.385 10 false Transmission Control ECU 5.646,0.396 6.104,0.594 0.458,0.198 10 false 36 5.719,2.208 6.177,2.406 0.458,0.198 10 false 1 5.615,2.531 6.073,2.729 0.458,0.198 10 false I35 5.604,2.74 7.021,3.167 1.417,0.427 10 false Shift Lock Control Unit Assembly 5.583,3.667 6.042,3.865 0.458,0.198 10 false 14 5.594,4.177 6.052,4.375 0.458,0.198 10 false 21 5.573,3.896 6.031,4.094 0.458,0.198 10 false I39 5.583,4.396 6.042,4.594 0.458,0.198 10 false I40 5.917,4.271 6.375,4.469 0.458,0.198 10 false STP1 5.948,3.896 6.406,4.094 0.458,0.198 10 false P 6.583,4.469 7.042,4.667 0.458,0.198 10 false IC 5.542,5.125 7.073,5.552 1.531,0.427 10 false Certification ECU (Smart Key ECU Assembly) 1.375,0.396 1.833,0.594 0.458,0.198 10 false 37 1.375,1.813 2.219,2.052 0.844,0.24 10 false 22 0.125,0.833 0.583,1.031 0.458,0.198 10 false B20 0.104,1.021 3.458,1.51 3.354,0.49 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 0.656,2.51 1.865,2.927 1.208,0.417 10 false ECM 0.646,2.302 1.677,2.594 1.031,0.292 10 false B70 0.917,0.51 1.438,0.708 0.521,0.198 10 false STP2 0.979,1.938 1.438,2.135 0.458,0.198 10 false STP 0.313,4.146 1.198,4.625 0.885,0.479 10 false from Battery 1.656,4.333 2.115,4.531 0.458,0.198 10 false STOP 2.156,4.052 2.615,4.25 0.458,0.198 10 false 7 2.156,4.417 2.615,4.615 0.458,0.198 10 false 2 2.354,4.188 2.813,4.385 0.458,0.198 10 false B 2.344,4.542 2.802,4.74 0.458,0.198 10 false GND 2.781,4.385 3.24,4.583 0.458,0.198 10 false IC 3.115,4.281 3.573,4.479 0.458,0.198 10 false L 3.302,4.281 3.76,4.479 0.458,0.198 10 false 3 2.094,4.938 2.552,5.135 0.458,0.198 10 false B43 2.083,5.104 4.344,5.448 2.26,0.344 10 false Stop Light Switch Assembly

w/ Stop and Start System:
B626030E02
5.26,5.927 6.615,6.229 1.354,0.302 10 false Starter Assembly 0.531,3.156 1.885,3.458 1.354,0.302 10 false ECM 0.531,2.99 1.885,3.292 1.354,0.302 10 false B70 4.323,1.865 5.698,2.375 1.375,0.51 10 false Park/Neutral Position Switch Assembly 4.313,1.708 5.688,2.219 1.375,0.51 10 false C34 5.573,3.052 7.073,3.594 1.5,0.542 10 false Certification ECU (Smart Key ECU Assembly) 0.094,6.156 2.177,6.771 2.083,0.615 10 false Engine Stop and Start ECU 0.094,5.948 2.177,6.563 2.083,0.615 10 false B38 3.333,3.906 4.26,4.75 0.927,0.844 10 false ST NO. 1 3.25,5.969 4.031,6.573 0.781,0.604 10 false ST NO. 1*1, ST NO. 3*2 5.969,3.74 6.927,4.406 0.958,0.667 10 false from Battery 3.833,1.469 5.208,1.979 1.375,0.51 10 false B 4.115,1.469 5.49,1.979 1.375,0.51 10 false L 3.583,2.021 4.958,2.531 1.375,0.51 10 false N 3.583,1.771 4.958,2.281 1.375,0.51 10 false P 5.563,2.896 7.063,3.438 1.5,0.542 10 false I40 5.542,0.833 6.292,1.521 0.75,0.688 10 false 10 5.813,0.813 6.563,1.5 0.75,0.688 10 false STAR 5.823,2.438 6.573,3.125 0.75,0.688 10 false STA 5.594,2.344 6.344,3.031 0.75,0.688 10 false 3 6.49,1.094 7.063,1.833 0.573,0.74 10 false IC 3.74,1.219 4.49,1.906 0.75,0.688 10 false 4 4.031,2.281 4.781,2.969 0.75,0.688 10 false 5 0.865,2.448 2.219,2.75 1.354,0.302 10 false STA 0.833,0.917 2.188,1.219 1.354,0.302 10 false NSW 1.26,0.813 2.615,1.115 1.354,0.302 10 false 30 1.26,2.313 2.615,2.615 1.354,0.302 10 false 25 0.875,5.417 1.313,5.646 0.438,0.229 10 false STA 1.271,5.271 1.844,5.531 0.573,0.26 10 false 21 1.26,4.167 2.615,4.469 1.354,0.302 10 false 17 0.885,4.281 2.24,4.583 1.354,0.302 10 false CLL 3.198,5.292 3.406,5.521 0.208,0.229 10 false 5 3.906,5.292 4.573,5.51 0.667,0.219 10 false 3 3.198,5.552 3.552,5.854 0.354,0.302 10 false 2 3.906,5.552 4.573,5.75 0.667,0.198 10 false 1 4.896,5.406 6.25,5.708 1.354,0.302 10 false C181 5.021,5.208 5.771,5.896 0.75,0.688 10 false 1 5.292,5.406 6.646,5.708 1.354,0.302 10 false ST 6.458,5.406 7.073,5.865 0.615,0.458 10 false C180 6.25,5.396 6.865,5.854 0.615,0.458 10 false B 6.552,5.198 7.094,5.635 0.542,0.438 10 false 1 0.188,8.25 3.24,8.688 3.052,0.438 10 false *2: w/ Cold Area Specification Vehicles 0.188,7.823 3.24,8.26 3.052,0.438 10 false *1: w/o Cold Area Specification Vehicles

w/o Stop and Start System:
B616494E02
6.573,0.875 6.885,1.073 0.313,0.198 10 false IC 5.906,0.792 6.365,1.021 0.458,0.229 10 false STAR 6.25,0.406 6.563,0.604 0.313,0.198 10 false +B 5.615,0.781 5.927,0.979 0.313,0.198 10 false 10 5.677,3.26 5.99,3.458 0.313,0.198 10 false 3 5.938,3.375 6.396,3.604 0.458,0.229 10 false STA 5.563,3.635 6.021,3.865 0.458,0.229 10 false I40 5.531,3.823 7.063,4.26 1.531,0.438 10 false Certification ECU (Smart Key ECU Assembly) 5.969,5.563 6.844,6.063 0.875,0.5 10 false from Battery 4.427,5.521 4.833,5.719 0.406,0.198 10 false C153 4.552,5.302 4.865,5.5 0.313,0.198 10 false 1 3.708,4.885 4.021,5.083 0.313,0.198 10 false 1 3.313,4.906 3.885,5.104 0.573,0.198 10 false C155 3.542,5.354 3.854,5.552 0.313,0.198 10 false ST 3.115,6.125 4.458,6.521 1.344,0.396 10 false Starter Assembly 4.219,5.385 4.531,5.583 0.313,0.198 10 false B 4.115,3.677 4.875,3.958 0.76,0.281 10 false ST NO.1 3.688,3.927 4.521,4.469 0.833,0.542 10 false ST NO. 1*1, ST NO. 3*2 3.042,4.354 3.281,4.594 0.24,0.24 10 false 1 3.354,4.354 3.698,4.635 0.344,0.281 10 false 3 3.052,3.635 3.24,3.938 0.188,0.302 10 false 2 3.354,3.635 3.781,3.885 0.427,0.25 10 false 5 3.063,2.667 3.375,2.865 0.313,0.198 10 false 5 2.896,1.865 3.052,2.083 0.156,0.219 10 false B 3.177,1.865 3.333,2.083 0.156,0.219 10 false L 2.625,2.135 2.781,2.354 0.156,0.219 10 false P 2.615,2.406 2.771,2.625 0.156,0.219 10 false N 2.813,1.583 3.125,1.781 0.313,0.198 10 false 4 1.354,0.771 2.5,1.042 1.146,0.271 10 false 30 1.375,3.229 2.677,3.531 1.302,0.302 10 false 25 0.99,3.333 1.448,3.563 0.458,0.229 10 false STA 0.906,0.802 1.365,1.031 0.458,0.229 10 false NSW 0.604,3.823 1.875,4.104 1.271,0.281 10 false B70 0.604,4.031 1.219,4.573 0.615,0.542 10 false ECM 3.417,2.021 3.875,2.25 0.458,0.229 10 false C34 3.417,2.271 4.729,2.823 1.313,0.552 10 false Park/Neutral Position Switch Assembly 0.417,5.219 1.854,5.948 1.438,0.729 10 false *1: w/o Cold Area Specification Vehicles 0.417,5.948 1.875,6.646 1.458,0.698 10 false *2: w/ Cold Area Specification Vehicles 3.302,5.125 3.875,5.323 0.573,0.198 10 false C156 3.719,5.125 4.031,5.323 0.313,0.198 10 false 1 4.823,5.521 5.344,5.708 0.521,0.188 10 false C154 3.073,4.885 3.646,5.083 0.573,0.198 10 false *1 4.917,5.74 5.49,5.938 0.573,0.198 10 false *1 4.5,5.74 5.073,5.938 0.573,0.198 10 false *2 3.083,5.104 3.656,5.302 0.573,0.198 10 false *2 4.948,5.313 5.26,5.51 0.313,0.198 10 false 1


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:
·

If the ignition switch is changed from ON to ACC with the shift lever in any position other than P, and then the shift lever is moved to P and the engine switch is pressed with the brake pedal depressed, the ignition switch will turn off.

·

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure will be released and the force required to depress the brake pedal to illuminate the stop lights will increase.



PROCEDURE

1.CHECK WHETHER ENGINE STARTS
a.

Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the ignition switch to ON.


b.

Check that the engine can be started 5 seconds after the ignition switch turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
2.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

3.CHECK FOR DTC
a.

Using the GTS, check if LIN communication DTC B278588 and B278987 are output.

Body Electrical > Entry&Start > Trouble Codes
50001 440
OK:

DTC B278588 and B278987 are not output.



Result:
Proceed to
OK
NG



OK

4.CHECK ENGINE CRANKING OPERATION

NG

GO TO LIN COMMUNICATION SYSTEM (DTC B278588)

4.CHECK ENGINE CRANKING OPERATION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch and check that the engine cranks.


Result:
Result Proceed to
Engine cranks and initial combustion occurs A
Engine cranks but initial combustion does not occur (for Gasoline) B
Engine cranks but initial combustion does not occur (for Diesel) C
Engine does not crank D



A

B

C

D

5.CHECK ENGINE SWITCH CONDITION
5.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off A
Power source mode does not change to ACC or ON B
Power source mode changes to ON but not to ACC C
Power source mode changes to ACC but not to ON D



A

6.READ VALUE USING GTS (STOP LIGHT SWITCH)

B

C

D

6.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch
50003 454 206
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

19.INSPECT STOP LIGHT SWITCH ASSEMBLY
7.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 454 205
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)

NG

21.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
8.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG

22.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
9.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state OFF, ACC ON, IGR ON, IGP ON or Starter ON OFF: Ignition switch off
ACC ON: Ignition switch ACC
IGR ON: Ignition switch ON
IGP ON: Ignition switch ON
Starter ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 454 405
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK (w/ Stop and Start System)
OK (w/o Stop and Start System)
NG



OK (w/ Stop and Start System)

10.CHECK VEHICLE TYPE

OK (w/o Stop and Start System)

40.CHECK VEHICLE TYPE

NG

59.CHECK STEERING LOCK FUNCTION
10.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Gasoline A
for Diesel (w/ Cold Area Specification Vehicles) B
for Diesel (w/o Cold Area Specification Vehicles) C



A

11.INSPECT ST NO. 1 RELAY

B

30.INSPECT ST NO. 3 RELAY

C

35.INSPECT ST NO. 1 RELAY
11.INSPECT ST NO. 1 RELAY

OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)

NG

25.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
13.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the C52 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 3 - C52-2 (ST) Always Below 1 Ω
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 3 or C52-2 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT ST NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT ST NO. 2 RELAY

OK

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 2 RELAY)

NG

REPLACE ST NO. 2 RELAY

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 2 RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
(ST No. 2 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST No. 2 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BATTERY AND GROUND)

NG

26.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ENGINE STOP AND START ECU)
17.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
(ST NO. 2 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 2 RELAY)
a.

Disconnect the C52 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 2 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 3 - C52-1 (SL2) Always Below 1 Ω
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 2 relay terminal 3 or C52-1 (SL2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the I40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B43 stop light switch assembly connector.


c.

Disconnect the B2*1, B1*2, B70*3 ECM connector.

*1: for 1GR-FE

*2: for V35A-FTS

*3: for F33A-FTV


d.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the I35 shift lock control unit assembly connector.


f.

Disconnect the C36 transmission control ECU connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I40,B43)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

I40-21 (STP1) - B43-3 (L) Always Below 1 Ω
I40-21 (STP1) or B43-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I39)Location & Routing

Click Connector(I39)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I39-14 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
22.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the B2*1, B1*2, B70*3 ECM connector.

*1: for 1GR-FE

*2: for V35A-FTS

*3: for F33A-FTV


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)



OK

NG (w/ Stop and Start System)

24.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)

NG (w/o Stop and Start System)

28.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I35 shift lock control unit assembly connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the B38 engine stop and start ECU connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch Shift position (P and N) OFF or ON OFF: Shift lever in any position other than P or N
ON: Shift lever in P or N
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

NG

28.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
25.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-5 (L) - No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
C34-5 (L) or No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (ST NO. 2 RELAY - ENGINE STOP AND START ECU)
a.

Disconnect the B38 engine stop and start ECU connector.


b.

Disconnect the B1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B38,B1)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

Click Connector(B1)Engine Compartment>Engine Room Main Wire / Lamp Wire / No. 2 Engine Room Wire / No. 2 Lamp Wire / No. 3 Engine Room Wire / No. 6 Engine Room Wire / Washer Wiring Assembly>ECM

ST NO. 2 relay installation terminal 2 - B38-23 (STA2) Always Below 1 Ω
ST NO. 2 relay installation terminal 2 - B1-34 (STA) Always Below 1 Ω
ST NO. 2 relay installation terminal 2 or B38-23 (STA2) - Other terminals and body ground Always 10 kΩ or higher
ST NO. 2 relay installation terminal 2 or B1-34 (STA) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the B1 ECM connector.


e.

Install the ST NO. 2 relay.


Result:
Proceed to
OK
NG



OK

27.CHECK ENGINE STOP AND START ECU (TERMINAL STA2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK ENGINE STOP AND START ECU (TERMINAL STA2)
A397704C96
3.188,0.083 3.604,0.323 0.417,0.24 2.781,1.469 3.135,0.802 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 3.271,0.115 3.667,0.313 0.396,0.198 10 false B38 2.594,1.5 3.125,1.698 0.531,0.198 10 false STA2
*a Component without harness connected
(Engine Stop and Start ECU)
- -


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B38)Location & Routing

Click Connector(B38)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Engine Stop and Start ECU

B38-23 (STA2) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

NG

28.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the I40 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.INSPECT ST NO. 3 RELAY

OK

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 3 RELAY)

NG

REPLACE ST NO. 3 RELAY

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 3 RELAY)
a.
C421133C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 3 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (ST NO. 3 RELAY - BATTERY AND GROUND)

NG

34.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 3 RELAY)
32.CHECK HARNESS AND CONNECTOR (ST NO. 3 RELAY - BATTERY AND GROUND)
a.
C421133C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 3 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 3 RELAY)
a.

Disconnect the C181 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C181)Location & Routing

Click Connector(C181)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 3 - C181-1 (ST) Always Below 1 Ω
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 3 or C181-1 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 3 RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-5 (L) - No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 2 Always Below 1 Ω
C34-5 (L) or No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.INSPECT ST NO. 1 RELAY

OK

36.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

36.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

37.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)

NG

39.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
37.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the C181 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C181)Location & Routing

Click Connector(C181)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 3 - C181-1 (ST) Always Below 1 Ω
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 3 or C181-1 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-5 (L) - No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
C34-5 (L) or No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Gasoline A
for Diesel (w/ Cold Area Specification Vehicles) B
for Diesel (w/o Cold Area Specification Vehicles) C



A

41.INSPECT ST NO. 1 RELAY

B

47.INSPECT ST NO. 3 RELAY

C

53.INSPECT ST NO. 1 RELAY
41.INSPECT ST NO. 1 RELAY

OK

42.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

42.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

43.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)

NG

46.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
43.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

44.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the C101*1, C52*2 starter assembly connector.

*1: for 1GR-FE

*2: for V35A-FTS


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE:
Tester Connection Condition Specified Condition

Click Location & Routing(C101)Location & Routing

Click Connector(C101)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 3 - C101-1 (ST) Always Below 1 Ω
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 3 or C101-1 (ST) - Other terminals and body ground Always 10 kΩ or higher

for V35A-FTS:
Tester Connection Condition Specified Condition

Click Location & Routing(C52)Location & Routing

Click Connector(C52)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 3 - C52-2 (ST) Always Below 1 Ω
No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 3 or C52-2 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-5 (L) - No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
C34-5 (L) or No. 2 engine room relay block and No. 2 junction block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.INSPECT ST NO. 3 RELAY

OK

48.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 3 RELAY)

NG

REPLACE ST NO. 3 RELAY

48.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 3 RELAY)
a.
C421133C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 3 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

49.CHECK HARNESS AND CONNECTOR (ST NO. 3 RELAY - BATTERY AND GROUND)

NG

52.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
49.CHECK HARNESS AND CONNECTOR (ST NO. 3 RELAY - BATTERY AND GROUND)
a.
C421133C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 3 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

50.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

50.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 3 RELAY)
a.

Disconnect the C156 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C156)Location & Routing

Click Connector(C156)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 3 - C156-1 (ST) Always Below 1 Ω
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 3 or C156-1 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

51.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.

Disconnect the C153 starter assembly connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

52.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-5 (L) - No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 2 Always Below 1 Ω
C34-5 (L) or No. 4 engine room relay block and No. 4 junction block assembly ST NO. 3 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

53.INSPECT ST NO. 1 RELAY

OK

54.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

54.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 2 - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off) 6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

55.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)

NG

58.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
55.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BATTERY AND GROUND)
a.
C378519C02
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 4 Engine Room Relay Block and No. 4 Junction Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

56.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

56.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the C155 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C155)Location & Routing

Click Connector(C155)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Starter Assembly

No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 3 - C155-1 (ST) Always Below 1 Ω
No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 3 or C155-1 (ST) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

57.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - BATTERY)
a.

Disconnect the C154 starter assembly connector.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

58.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(C34)Location & Routing

Click Connector(C34)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>Park/Neutral Position Switch Assembly

C34-5 (L) - No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
C34-5 (L) or No. 4 engine room relay block and No. 4 junction block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG