Home › Engine / Hybrid System › B48 (ENGINE MECHANICAL) › CRANKSHAFT
RM3650E _51 Engine / Hybrid System _080178 B48 ENGINE MECHANICAL _0388879 CRANKSHAFT A

B48 ENGINE MECHANICAL  CRANKSHAFT  DISASSEMBLY  


PROCEDURE

Hide 2.REMOVE SPARK PLUG

Hide 12101A 3.REMOVE OIL PAN DRAIN PLUG

Hide 12101A 4.INSTALL OIL PAN DRAIN PLUG

Hide 23801P 5.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23100X 6.REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY

Hide 23250 7.REMOVE FUEL INJECTOR ASSEMBLY

Hide 15370J 8.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 23285A 9.REMOVE NO. 1 CHECK VALVE

Hide 11201 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 15474 12.REMOVE OUTLET TURBO OIL PIPE

Hide 15407 13.REMOVE INLET TURBO OIL PIPE SUB-ASSEMBLY

Hide 14.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.
A441648

Thread the sealing cap (1) out and remove.


b.
A441404

Turn the engine with the special tool 0 493 380 (11 6 480) to the TDC firing position of cylinder 1.

SST
09200-WA190  

NOTICE:
·

Damage to the engine.

The engine may be damaged if it is manually rotated in the wrong direction.

-

Always rotate the engine in the correct direction of rotation by hand: a) Clockwise, facing the vibration damper or b) Counter-clockwise, facing the timing chain. (b) only applies when the chain sub-assembly is installed.





c.
A441715

Insert special tool 2 288 380 into the dowel hole up to dimension (X).

SST
09200-WA570  

i.

Dimension (X) = 66 mm (2.60 in.)



d.
A441716

Position special tool 2 288 380 correctly.

SST
09200-WA570  

i.

The engine is in the TDC firing position of cylinder 1.



e.
A441717

Ensure that the special tool 2 288 380 is not incorrectly positioned.

SST
09200-WA570  

i.

The TDC firing position of cylinder 1 was not reached.



f.
A441417

Make sure that the marks (1) on the intake camshaft sub-assembly (E) and the exhaust camshaft sub-assembly (A) are legible from above.


g.
A441416

Ensure that the cam (1) on the exhaust camshaft sub-assembly on cylinder 1 points to the inside right at a slight angle.


h.
A441415

Ensure that the cam (1) on the intake camshaft sub-assembly on cylinder 1 points to the inside left at an angle.


i.
A441418

Ensure that the flattened areas (1) on the intake camshaft sub-assembly and the exhaust camshaft sub-assembly point upwards.


j.
A441406

Position the basic carrier (1) from the set of special tools 2 456 372 on the cylinder head sub-assembly.

SST
09200-WA700  


k.

Tighten the bolts (2) from the set of special tools 2 456 372.

SST
09200-WA700  

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


l.
A441408

Position the test gauge (2) from the set of special tools 2 358 122 between the intake camshaft sub-assembly and the basic carrier (1) from the set of special tools 2 456 372 .

SST
09200-WA380  
09200-WA700  


m.

Position the test gauge (3) from the set of special tools 2 358 122 between the exhaust camshaft sub-assembly and the basic carrier (1) from the set of special tools 2 456 372.

SST
09200-WA380  
09200-WA700  


n.

Tighten bolts (arrows).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 13540 15.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 135A0 16.LOOSEN INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 135A0A 17.LOOSEN EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 135A0 18.REMOVE INTAKE CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 135A0A 19.REMOVE EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY

Hide 13050 20.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 21.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 16028 24.REMOVE NO. 2 TURBO WATER PIPE SUB-ASSEMBLY

Hide 11101 25.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 13470 26.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 27.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12101 28.REMOVE OIL PAN SUB-ASSEMBLY

a.
A441198

Unlock plug connection (1) and disconnect.


b.

Release the cable from the clips (2) of the oil pan sub-assembly.


c.
A441247

Loosen E10 bolts (1), (2) and (3).


d.
A441245

Loosen E10 bolts (1) to (7).


e.
A441246

Loosen E10 bolts (1) to (7).


f.
A441200

Loosen E10 bolts (1) and (2).


g.
A444616

Loosen the oil pan sub-assembly in the marked areas.

HINT:

Increased force may be necessary during disassembly because the component is bonded with seal packing.



h.
A441225

Remove oil pan sub-assembly (1) from the bottom rear.


Hide 15100 29.REMOVE OIL PUMP ASSEMBLY

Hide 12121 30.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A441683

Release all E10 bolts (arrows).


b.

Remove the No. 1 oil pan baffle plate (1).


Hide 13201 31.REMOVE CONNECTING ROD SUB-ASSEMBLY

Hide 13506 34.REMOVE CHAIN SUB-ASSEMBLY

Hide 13507A 35.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

a.
A442091

Guide out and remove oil pump drive chain sub-assembly (1) from crankshaft (2).


Hide 13411 36.REMOVE CRANKSHAFT

NOTICE:
·

Engine damage may result from incorrectly installing crankshaft bearings and crankshaft bearing caps.

-

Always install all crankshaft bearings and crankshaft bearing caps in the same position from which they were removed.




a.
A441693

Remove both sealing caps (1) with a suitable tool (2).


b.
A441694

Rotate the crankshaft to the TDC of the first cylinder.


c.

Mount the special tool 2 288 054 and abut the bolts (1).

SST
09200-WA850  


d.
A441695

Make sure the special tool 2 288 054 is correctly fitted in the guides (1) of the No. 1 balanceshafts (2).

SST
09200-WA850  

HINT:

The description is for one component only.

The procedure is identical for all funther components.



e.

If necessary, turn the crankshaft slightly.


f.

Tighten special tool 2 288 054.

SST
09200-WA850  

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


g.
A446437

Loosen E14 bolt (1) on the No. 1 balanceshafts on the intake side.


h.
A441694

Loosen bolts (1).


i.

Guide the special tool 2 288 054 out and remove.

SST
09200-WA850  


j.
A446438

Guide out No. 1 balanceshaft (1) on the intake side from crankshaft (2) in the direction of the arrow.


k.
A446440

Carefully place aside No. 1 balanceshaft (1) on the intake side.


l.
A446441

Position a cloth (1) between No. 1 balanceshaft (2) on the intake side and crankcase (3).


m.

Ensure that needle bearing (4) is not damaged.


n.
A441458

Unfasten nut (1).


o.
A446443

Thread out the No. 2 balanceshaft driven gear (1) and remove.


p.
A441708

Observe the numbering (1) of the crankshaft bearing cap.

i.

The mounting orientation must be maintained.



q.
A441709

Loosen E14 bolts in the order (10) to (1).

HINT:
·

The crankshaft bearing cap, main bearing shell and guide bearing shell are aligned with each other.

Always install the crankshaft bearing cap, main bearing shells and guide bearing shells in the cylinder from which they were removed.




r.
A441710

Guide out and remove crankshaft (1).

CAUTION:
·

Heavy component.

Heavy components can lead to injury or damage.

-

Remove and install heavy components with the aid of another person/other persons.





Hide 11711 37.REMOVE CRANKSHAFT BEARING

NOTICE:
·

Engine damage may result from incorrectly installing crankshaft bearings and crankshaft bearing caps.

-

Always install all crankshaft bearings and crankshaft bearing caps in the same position from which they were removed.




a.
A447285

Enter the code letter on the crankcase in the table.

i.

K = Clutch side


ii.

The position numbers (1) to (5) describe the bearing seats 1 to 5. The identification number is always located on the crankshaft bearing caps.



b.
A447284

Enter the identification number on the crankshaft in the table.

i.

The position numbers (1) to (5) describe the bearing seats 1 to 5. The identification number is always located on the crankshaft bearing caps.



c.

Enter the code letters of the crankcase and the identification numbers of the crankshaft.

Code letter on the crankcase Key performance indicator on the crankshaft
Bearing seat 1
Bearing seat 2
Bearing seat 3
Bearing seat 4
Bearing seat 5


d.
A456244

Using the table, determine the correct crankshaft bearing with lubrication groove (1) for the crankcase.

i.

The crankshaft bearing are classified by means of numbers.

A B C
1 Classification 1 Classification 2 Classification 2
2 Classification 1 Classification 2 Classification 3
3 Classification 2 Classification 2 Classification 3



e.
A456245

Using the table, determine the correct upper crankshaft thrust washer with lubrication groove (1) for the crankcase.

i.

The crankshaft bearing are classified by means of numbers.

A B C
1 Classification 1 Classification 2 Classification 2
2 Classification 1 Classification 2 Classification 3
3 Classification 2 Classification 2 Classification 3



f.
A456247

Using the table, determine the correct crankshaft bearing without lubrication groove (1) for the respective cranlshaft bearing cap.

i.

The crankshaft bearing are classified by means of numbers.

A B C
1 Classification 1 Classification 1 Classification 2
2 Classification 2 Classification 2 Classification 2
3 Classification 2 Classification 3 Classification 3



g.
A456246

Using the table, determine the correct lower crankshaft thrust washer without lubrication groove (1) for the respective cranlshaft bearing cap.

i.

The crankshaft bearing are classified by means of numbers.

A B C
1 Classification 1 Classification 1 Classification 2
2 Classification 2 Classification 2 Classification 2
3 Classification 2 Classification 3 Classification 3



h.
A441711

Remove the crankshaft bearings with lubricating groove (1) to (2) and (4) to (5) from the crankcase.


i.

Remove the upper crankshaft thrust washer with lubricating groove (3) from the crankcase.


j.
A441392

Remove the crankshaft bearings (1) to (2) and (4) to (5) from the crankshaft bearing cap.


k.

Remove the lower crankshaft thrust washer (3) from the crankshaft bearing caps.