Home › ENGINE › 1GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P1604    Startability Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.
Using the Techstream, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No.
DTC Detection Condition
Trouble Area
P1604
Either condition is met:
  1. The engine speed is below 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below) (1 trip detection logic).
  2. After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds (1 trip detection logic).
  1. Engine immobiliser system
  2. Engine assembly (excess friction, compression loss)
  3. Starter
  4. Crankshaft position sensor
  5. VVT sensor
  6. Engine coolant temperature sensor
  7. Fuel pump
  8. Fuel pump control system
  9. Fuel pipes
  10. Fuel injector assembly
  11. Throttle with motor body assembly
  12. Pressure regulator
  13. Battery
  14. Drive plate and ring gear sub-assembly*1
  15. Flywheel sub-assembly*2
  16. Spark plug
  17. Ignition coil circuit
  18. Intake system
  19. Camshaft timing oil control valve assembly
  20. Mass air flow meter
  21. Air fuel ratio sensor
  22. Valve timing
  23. Fuel
  24. Purge VSV
  25. Intake valve
  26. Exhaust valve
  27. ECM
  1. *1: for Automatic Transmission Models
  1. *2: for Manual Transmission Models

A220316E01


WIRING DIAGRAM

Refer to DTC P0102 for the mass air flow meter circuit .
Refer to DTC P0115 for the engine coolant temperature sensor circuit .
Refer to DTC P0335 for the VVT sensor circuit and crankshaft position sensor circuit .
Refer to DTC P0351 for the ignition coil circuit .
Refer to DTC P0451 for the EVAP system circuit .
Refer to DTC P2195 for the air fuel ratio sensor circuit .
Refer to DTC Fuel Pump Control Circuit .
Refer to DTC Fuel Injector Circuit .

INSPECTION PROCEDURE

HINT:
  1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
    As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
  2. If any other DTCs are output, perform troubleshooting for those DTCs first.
  3. When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
  4. Read freeze frame data using the Techstream. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  5. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
  6. When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
  7. Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
  8. If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
  9. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
  10. If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.


Malfunction Recurrence and Inspection Areas
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    1. The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

      HINT:
      One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.

      1. If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.
      2. If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

      3. If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or an ECM may be malfunctioning.


        A215383E40

    2. All engine speeds recorded in the freeze frame data are between 60 and 250 rpm (the engine cranks but there is no combustion).

      HINT:
      If the engine speed is between 60 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.


        A215384E45

    3. The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

      HINT:
      If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.

      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
      2. If Long FT is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

      3. If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.


        A215383E02

  2. When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem symptoms" and "Systems to inspect")

    1. Problem symptoms

      1. The engine does not crank.

        HINT:
        The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.

      2. The engine cranking speed is abnormal.

        HINT:
        If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.

      3. There is no initial combustion.

        HINT:
        If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.

      4. The engine stalls after starter turnoff.

        HINT:
        If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.

      5. The initial combustion and starter turnoff occur late.

        HINT:
        If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).

        HINT:
        Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
        1. When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
        2. When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
        3. When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.

    2. Systems to inspect.

      1. Intake system
      2. Ignition system
      3. Fuel system


INSPECTION FLOW
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    Freeze Frame Data Item
    Result
    Suspected Area
    Procedure
    Engine Speed
    0 rpm (no engine cranking at all)
    1. Battery fully depleted
    2. Engine assembly (excess friction)
    3. Starter
    4. Crankshaft position sensor
    5. ECM
    4 to 10
    60 to 250 rpm (engine cranks but no initial combustion*1)
    1. Fuel pump control system
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Fuel injection system
    11 to 15
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
    1. Engine assembly (compression loss)
    2. Fuel injection system
    3. Fuel pump control system
    16 to 24

    HINT:
    1. *1: First combustion after cranking begins.
    2. *2: Condition when engine speed increases and starter can be turned off.

  2. When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

    1. Problem symptoms

      Problem Symptom
      Suspected Area
      Suspected Component
      Procedure
      The engine does not crank
      Battery malfunction
      1. Battery fully depleted
      26 to 32
      Starting system
      1. Starter (includes pinion gear wear or tooth damage)
      2. Starting system
      Engine assembly
      1. Engine assembly (excess friction)
      2. Drive plate wear or tooth damage
      3. Flywheel wear or tooth damage
      Cranking speed too low
      Battery malfunction
      1. Battery fully depleted
      33 to 35
      Starting system
      1. Starter
      Engine assembly
      1. Engine assembly (excess friction)
      Cranking speed too high
      Engine assembly
      1. Engine assembly (compression loss)
      There is no initial combustion
      Fuel supply problem
      1. Cannot maintain pressure due to pressure regulator malfunction
      2. Fuel injector assembly leak
      3. Fuel leak from fuel line
      4. Fuel pump control system
      5. Fuel pump
      36 to 51
      Ignition system malfunction
      1. Spark plug
      2. Crankshaft position sensor
      3. Ignition coil assembly
      Engine stalls after starter turnoff
      Air suction
      1. Intake system connections
      52 to 58
      Deposits in throttle with motor body assembly
      1. Throttle with motor body assembly
      VVT valve does not return properly
      1. Camshaft timing oil control valve assembly
      Mass air flow meter malfunction
      1. Mass air flow meter
      The initial combustion and starter turnoff occur late
      Engine coolant temperature sensor malfunction
      1. Engine coolant temperature sensor
      59 to 72
      Mass air flow meter malfunction
      1. Mass air flow meter
      Abnormal A/F learning value
      1. Air fuel ratio sensor
      Deviation from fuel injection characteristics
      1. Fuel injector assembly
      Wet-fouled or dry-fouled spark plug
      1. Spark plug
      Lack of fuel pressure
      1. Pressure regulator
      2. Fuel pump
      3. Fuel pump control system

    2. Systems to inspect.

      Troubleshooting by System
      Suspected Area
      Suspected Component
      Procedure
      Fuel system troubleshooting A
      Abnormal A/F learning value
      1. Fuel injector assembly
      89 to 96
      97 to 104
      Rough idling
      1. Crankshaft position sensor
      Abnormal fuel pressure
      1. Fuel
      2. Fuel leak from fuel line
      3. Fuel pump
      4. Pressure regulator
      Fuel system troubleshooting B
      Abnormal concentration of HC in surge tank
      1. Purge VSV system
      2. Fuel injector assembly
      105 to 107
      Fuel system troubleshooting C
      Injection signal system malfunction
      1. Fuel injector assembly
      2. Crankshaft position sensor
      3. VVT sensor
      4. ECM
      74 to 78
      Intake system troubleshooting
      Difference between ISC target value and opening angle when idling
      1. Engine assembly (compression loss)
      2. Valve timing
      3. Engine coolant temperature sensor
      4. ECM
      86 to 88
      108 to 110
      Ignition system troubleshooting
      VVT sensor and/or crankshaft position sensor signal malfunction
      1. Crankshaft position sensor system (including sensor installation)
      2. VVT sensor system (including sensor installation)
      3. ECM
      79 to 88
      111 to 117

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.



    A103809E46
  1. Read DTCs and record the Freeze Frame Data.

    HINT:
    1. This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
    2. When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
    3. The fourth set of freeze frame data is the data recorded when the DTC is stored.

    Result 
    Result
    Proceed to
    Only DTC P1604 is output
    A
    DTCs other than P1604 are output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK ENGINE IMMOBILISER SYSTEM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Fuel Cut.

  1. Read the value displayed on the Techstream.

    OK:
    Immobiliser Fuel Cut is OFF

    HINT:
    1. If the engine is started immediately after reconnecting the battery terminal, the engine may stall immediately after it starts due to the intercommunication process between each ECU. For this reason, when starting the engine after reconnecting the battery terminal, first turn the ignition switch to ON and then wait several seconds for the communication process to complete before starting the engine.
    2. When this operation causes DTC P1604 to be stored, this is due to normal operation of the immobiliser system and does not indicate a malfunction, so clear the DTC and return the vehicle to the customer.



NG
REPAIR ENGINE IMMOBILISER SYSTEM (Click here)
OK


3.CHECK MALFUNCTION CONDITION
  1. Confirm the problem symptoms.
    Result 
    Result
    Proceed to
    Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
    A
    The problem symptoms can be reproduced, or the malfunction conditions are known
    B



B
Go to step 26
A


4.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Engine Speed
    Battery Voltage
    All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
    Minimum voltage is less than 5 V
    Battery fully depleted
    A
    Minimum voltage is 5 V or higher
    1. Starter malfunction
    2. Crankshaft position sensor system
    3. Excess engine friction
    4. ECM
    B
    60 to 250 rpm (engine cranks but no initial combustion)
    -
    1. Fuel pump control system
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Fuel injection system
    C
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
    -
    1. Engine assembly
    2. Fuel injection system
    3. Fuel pump control system
    D

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Low Rev for Eng Start
    ON exists
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter
    E

    HINT:
    When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the Freeze Frame Data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
    *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
    *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
    1. Immobiliser Fuel Cut
    2. Engine Speed (Starter Off)
    3. Shift SW Status (R, D Range)



B
Go to step 5

C
Go to step 11

D
Go to step 16

E
Go to step 52
A

CHARGE OR REPLACE BATTERY 

5.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Battery Voltage
    Minimum voltage is 6 V or higher and voltage does not fluctuate*1
    Starter system
    A
    Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
    1. Crankshaft position sensor system
    2. ECM
    B
    Minimum voltage is 5 to 6 V*4
    1. Excess engine friction
    2. Battery fully depleted
    C

    HINT:

    1. A217930E01
      *1: The 5 sets of freeze frame data show approximately the same battery voltage.
    2. *2: The 5 sets of freeze frame data show different battery voltages.
    3. *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
    4. *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
    5. Perform "Inspection After Repair" after replacing the engine assembly (Click here).



B
Go to step 6

C
CHECK AND REPAIR ENGINE OR BATTERY
A

CHECK STARTER SIGNAL CIRCUIT (Click here)  

6.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


7.CHECK CRANKSHAFT POSITION SENSOR
  1. Disconnect the B29 crankshaft position sensor connector.

  1. Check for oil on the connector terminals.

    OK:
    No oil on the terminals.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


8.INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the B29 crankshaft position sensor connector.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

11.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Intake Air
    Coolant Temp
    Fuel Pump Duty*3
    Fuel Pump/Speed Status*4
    Difference between Coolant Temp and Intake Air is 10°C or higher*1
    Coolant Temp is 125°C or more, or lower than outside temperature by 15°C or more
    -
    Engine coolant temperature sensor
    A
    Other than above
    No sets of freeze frame data are 0%*3
    All 5 sets of freeze frame data are ON*4
    -
    B
    At least 1 of the 5 sets of freeze frame data is 0%*3
    At least 1 of the 5 sets of freeze frame data is OFF*4
    Fuel pump control system
    C
    Difference between Coolant Temp and Intake Air is less than 10°C *2
    -
    At least 1 of the 5 sets of freeze frame data is 0%*3
    At least 1 of the 5 sets of freeze frame data is OFF*4
    Fuel pump control system
    No sets of freeze frame data are 0%*3
    All 5 sets of freeze frame data are ON*4
    -
    B

    HINT:
    1. *1: A long time had not elapsed after stopping the engine.
    2. *2: A long time had elapsed after stopping the engine.
    3. *3: w/ Secondary Air Injection System
    4. *4: w/o Secondary Air Injection System
    5. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



B
Go to step 12

C
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

12.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
  1. w/ Secondary Air Injection System:

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

    5. When performing the Active Test, check for an operating sound from the fuel pump.

      OK:
      Control the Fuel Pump / Speed
      Specified Condition
      ON
      Operating sound heard
      OFF
      Operating sound not heard

      HINT:
      Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



  1. w/o Secondary Air Injection System:



      A190138E38
    1. Connect the Techstream to the DLC3.

    2. Disconnect the fuel pump connector.

    3. Turn the ignition switch to ON.

    4. Turn the Techstream on.

    5. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      L5-4 - Body ground
      Active Test is being performed
      11 to 14 V

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Fuel Pump)

      HINT:
      1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
      2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY POWER SOURCE)
A167963E31
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR FUEL INJECTOR ASSEMBLY POWER SOURCE CIRCUIT (Click here)
OK


14.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 15
A

REPAIR OR REPLACE FUEL LINE 

15.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B



B
Go to step 25
A

REPAIR OR REPLACE FUEL SYSTEM 

16.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Intake Air
    Coolant Temp
    Long FT
    Engine Speed
    Difference between Coolant Temp and Intake Air is 10°C or more
    Coolant Temp is 125°C or more, or lower than outside temperature*1 by 15°C or more
    -
    -
    Engine coolant temperature sensor
    A
    Other than above
    -15% or less, or +15% or more
    -
    1. Fuel pump control system
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*2
    Engine assembly
    C
    Minimum speed is below 300 rpm
    1. Fuel system
    2. Intake air system
    D
    Difference between Coolant Temp and Intake Air is less than 10°C
    -
    -15% or less, or +15% or more
    -
    1. Fuel pump control system
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*2
    Engine assembly
    C
    Minimum speed is below 300 rpm
    1. Fuel system
    2. Intake air system
    D

    HINT:
    1. *1: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.
    2. *2: Compression loss may have occurred in the engine assembly.
    3. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor or engine assembly (Click here).



B
Go to step 17

C
CHECK AND REPAIR ENGINE ASSEMBLY

D
Go to step 19
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

17.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check that no carbon is stuck to the fuel injector assembly.

    OK:
    No carbon present.

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


18.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.
    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B



B
Go to step 25
A

REPAIR OR REPLACE FUEL SYSTEM 

19.READ FREEZE FRAME DATA
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    Engine coolant temperature is 40°C or less*1
    Pressure regulator
    A
    Engine coolant temperature is 40 to 90°C*2
    Fuel injector assembly
    B
    Engine coolant temperature is 90°C or more*3
    Pressure regulator
    A

    HINT:
    *1: If the engine coolant temperature is 40°C (104°F) or less (after stopping the engine and the vehicle is not driven for a long period of time), the pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: If the engine coolant temperature is 40 to 90°C (104 to 194°F)(15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector assembly.
    *3: If the engine coolant temperature is 90°C (194°F) or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.



B
Go to step 21
A


20.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, read the values after cranking the engine.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 25
A

REPLACE PRESSURE REGULATOR (Click here)  

21.CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    4000 ppm or higher
    A
    Less than 4000 ppm
    B

    HINT:
    If the concentration is 4000 ppm or higher, a fuel injector assembly may have a sealing problem.



B
Go to step 23
A


22.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assemblies (Click here).
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



B
Go to step 23
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

23.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.
    Result 
    Result
    Proceed to
    Carbon in passage
    A
    No carbon present
    B

    HINT:
    Perform "Inspection After Repair" after cleaning or replacing the throttle with motor body assembly (Click here).



B
Go to step 24
A

CLEAN OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)  

24.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


25.PERFORM SIMULATION TEST
  1. Check if the engine can be started.
    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 26
A

END 

26.CONFIRM PROBLEM SYMPTOM
  1. Confirm the problem symptoms.

    HINT:
    The problem symptoms below can be determined by reading the freeze frame data.


    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    The engine does not crank
    1. Battery fully depleted
    2. Starter (includes pinion gear wear or tooth damage)
    3. Starter system
    4. Engine assembly (excess friction)
    5. Drive plate wear or tooth damage*1
    6. Flywheel wear or tooth damage*2
    A
    Abnormal cranking speed
    1. Battery fully depleted
    2. Starter
    3. Engine assembly (excess friction, compression loss)
    B
    There is no initial combustion (combustion does not occur even once)*1
    1. Pressure regulator fuel pressure maintenance
    2. Fuel injector assembly leak
    3. Fuel leak from fuel line
    4. Fuel pump control system
    5. Fuel pump
    6. Spark plug
    7. Crankshaft position sensor system
    8. Ignition coil system
    C
    The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter system
    D
    The initial combustion and starter turnoff occur late*3
    1. Engine coolant temperature sensor
    2. Mass air flow meter
    3. Air fuel ratio sensor
    4. Fuel injector assembly
    5. Spark plug
    6. Pressure regulator
    7. Fuel pump assembly
    8. Fuel pump control system
    E
    1. *1: for Automatic Transmission Models
    2. *2: for Manual Transmission Models

    HINT:
    1. If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.
    2. *1: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
    3. *2: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve assembly may have a problem returning.
    4. *3: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).



B
Go to step 33

C
Go to step 36

D
Go to step 52

E
Go to step 59
A


27.PERFORM SIMULATION TEST
  1. When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely.*1
    1. Battery
    2. Excess engine friction
    3. Starter
    A
    A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely.
    1. Drive plate and ring gear sub-assembly*2
    2. Flywheel sub-assembly*3
    3. Starter
    B
    A noise indicating that the starter pinion gear is extending is not heard
    1. Battery
    2. Starter
    3. Starter system
    C

    HINT:
    *1: The battery may be fully depleted or there may be excess engine friction.
    *2: for Automatic Transmission Models
    *3: for Manual Transmission Models



B
Go to step 30

C
Go to step 31
A


28.INSPECT BATTERY
  1. Inspect the battery (Click here).



NG
CHARGE OR REPLACE BATTERY
OK


29.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    1. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
    2. Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

INSPECT STARTER (Click here)  

30.INSPECT STARTER
  1. Remove the starter (Click here).

  1. Check for starter pinion gear wear and damage.

    OK:
    There is no wear or damage.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for manual transmission models)
    B
    OK (for automatic transmission models)
    C



B
REPLACE FLYWHEEL SUB-ASSEMBLY (Click here)

C
REPLACE DRIVE PLATE AND RING GEAR (Click here)
A

REPLACE STARTER (Click here)  

31.INSPECT BATTERY
  1. Inspect the battery (Click here).



NG
CHARGE OR REPLACE BATTERY
OK


32.INSPECT STARTER
  1. Inspect the starter (Click here).



NG
REPLACE STARTER (Click here)
OK

CHECK STARTER SIGNAL CIRCUIT (Click here)  

33.PERFORM SIMULATION TEST
  1. Check the cranking speed.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Cranking speed is slow (100 rpm or less)
    1. Battery
    2. Starter
    3. Excess engine friction
    A
    Cranking speed is fast (300 rpm or more)*1
    Engine compression loss
    B

    HINT:
    1. *1: If the cranking speed is fast, there may be compression loss.
    2. Perform "Inspection After Repair" after replacing the engine assembly (Click here).



B
CHECK AND REPAIR ENGINE ASSEMBLY
A


34.INSPECT BATTERY
  1. Inspect the battery (Click here).



NG
CHARGE OR REPLACE BATTERY
OK


35.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    1. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.
    2. Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

INSPECT STARTER (Click here)  

36.CHECK FUEL INJECTOR ASSEMBLY
  1. Using a sound scope or screwdriver, check for an injector operating noise while cranking the engine.

    OK:
    Fuel injector assembly operating noise is heard.



NG
Go to step 49
OK


37.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 47
OK


38.INSPECT SPARK PLUG AND SPARK
  1. Inspect for sparks (Click here).



NG
Go to step 42
OK


39.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector assembly leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *4: From step 73, perform fuel system troubleshooting C (steps 74 to 78).



B
Go to step 41

C
Go to step 73
A


40.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
    Result 
    Result
    Proceed to
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 73, perform fuel system troubleshooting C (steps 74 to 78).



B
Go to step 73
A

REPLACE PRESSURE REGULATOR (Click here)  

41.CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    4000 ppm or higher
    A
    Less than 4000 ppm
    B*1

    HINT:
    1. If the concentration is 4000 ppm or higher, a fuel injector assembly may have a sealing problem.
    2. *1: From step 73, perform fuel system troubleshooting C (steps 74 to 78).
    3. Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



B
Go to step 73
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

42.INSPECT SPARK PLUG
  1. Inspect the spark plugs .

HINT:
  1. Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.
  2. Perform "Inspection After Repair" after replacing the spark plug (Click here).



NG
REPLACE SPARK PLUG (Click here)
OK


43.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the [Engine Speed] value.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
CHECK CRANKSHAFT POSITION SENSOR CIRCUIT
OK


44.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY POWER SOURCE)
A115969E91
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B7-1 (+B) - B7-4 (GND)
    Ignition switch ON
    11 to 14 V
    B24-1 (+B) - B24-4 (GND)
    Ignition switch ON
    11 to 14 V
    B6-1 (+B) - B6-4 (GND)
    Ignition switch ON
    11 to 14 V
    B23-1 (+B) - B23-4 (GND)
    Ignition switch ON
    11 to 14 V
    B5-1 (+B) - B5-4 (GND)
    Ignition switch ON
    11 to 14 V
    B20-1 (+B) - B20-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK POWER SOURCE CIRCUIT (IGNITION COIL ASSEMBLY POWER SOURCE)
OK


45.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the B7, B24, B6, B23, B5, and B20 ignition coil assembly connectors.

  1. Disconnect the B49 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B7-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B24-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B6-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B23-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B5-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B20-2 (IGF) - B49-6 (IGF1)
    Always
    Below 1 Ω
    B7-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B24-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B6-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B23-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B5-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B20-2 (IGF) or B49-6 (IGF1) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


46.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the B7, B24, B6, B23, B5, and B20 ignition coil assembly connectors.

  1. Disconnect the B49 and B48 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B7-3 (IGT1) - B49-24 (IGT1)
    Always
    Below 1 Ω
    B24-3 (IGT2) - B49-25 (IGT2)
    Always
    Below 1 Ω
    B6-3 (IGT3) - B49-26 (IGT3)
    Always
    Below 1 Ω
    B23-3 (IGT4) - B49-27 (IGT4)
    Always
    Below 1 Ω
    B5-3 (IGT5) - B49-28 (IGT5)
    Always
    Below 1 Ω
    B20-3 (IGT6) - B48-25 (IGT6)
    Always
    Below 1 Ω
    B7-3 (IGT1) or B49-24 (IGT1) - Body ground
    Always
    10 kΩ or higher
    B24-3 (IGT2) or B49-25 (IGT2) - Body ground
    Always
    10 kΩ or higher
    B6-3 (IGT3) or B49-26 (IGT3) - Body ground
    Always
    10 kΩ or higher
    B23-3 (IGT4) or B49-27 (IGT4) - Body ground
    Always
    10 kΩ or higher
    B5-3 (IGT5) or B49-28 (IGT5) - Body ground
    Always
    10 kΩ or higher
    B20-3 (IGT6) or B48-25 (IGT6) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the ignition coil assembly, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 73 and perform troubleshooting for the ignition system (steps 79 to 85).
    4. Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE IGNITION COIL ASSEMBLY (Click here)  

47.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:
    Control the Fuel Pump / Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


48.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 73 and perform fuel system troubleshooting (steps 74 to 78).



B
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPAIR OR REPLACE FUEL LINE 

49.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the [Engine Speed] value.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


50.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY POWER SOURCE)
A167963E32
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR FUEL INJECTOR ASSEMBLY POWER SOURCE CIRCUIT (Click here)
OK


51.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.

  1. Disconnect the B50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B11-2 - B50-6 (#10)
    Always
    Below 1 Ω
    B25-2 - B50-1 (#20)
    Always
    Below 1 Ω
    B10-2 - B50-7 (#30)
    Always
    Below 1 Ω
    B21-2 - B50-2 (#40)
    Always
    Below 1 Ω
    B9-2 - B50-8 (#50)
    Always
    Below 1 Ω
    B18-2 - B50-3 (#60)
    Always
    Below 1 Ω
    B11-2 or B50-6 (#10) - Body ground
    Always
    10 kΩ or higher
    B25-2 or B50-1 (#20) - Body ground
    Always
    10 kΩ or higher
    B10-2 or B50-7 (#30) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B50-2 (#40) - Body ground
    Always
    10 kΩ or higher
    B9-2 or B50-8 (#50) - Body ground
    Always
    10 kΩ or higher
    B18-2 - B50-3 (#60) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

52.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter .



NG
Go to step 58
OK


53.CHECK INTAKE SYSTEM
  1. Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (Click here).

    HINT:
    1. If the accelerator pedal is released after revving the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
    2. If Short FT #1, Short FT #2, Long FT #1 and Long FT #2 are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when revving the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.

    OK:
    There is no air leakage.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


54.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Disconnect the B14 throttle with motor body assembly connector.

    HINT:
    When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.

  1. Crank the engine and check that it starts.
    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start
    B

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



B
Go to step 56
A


55.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.

    OK:
    No carbon present.

    HINT:
    Perform "Inspection After Repair" after cleaning the throttle with motor body assembly (Click here).



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY
OK


56.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR)
  1. Perform the Active Test, referring to DTC P0011 inspection procedure .

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    3. If the camshaft timing oil control valve assembly is stuck ON, the valve overlap increases and combustion worsens due to the internal EGR which may cause the engine to stall.



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE SIDE) (Click here)
OK


57.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT EXHAUST LINEAR)
  1. Perform the Active Test, referring to DTC P0014 inspection procedure .
    Result 
    Result
    Proceed to
    NG
    A
    OK
    B*1

    HINT:
    1. *1: From step 73, perform intake system troubleshooting (steps 86 to 88). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 89 to 96).
    2. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    3. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    4. If the camshaft timing oil control valve assembly is stuck ON, the valve overlap increases and combustion worsens due to the internal EGR which may cause the engine to stall.



B
Go to step 73
A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST SIDE) (Click here)  

58.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the B51 mass air flow meter connector.

  1. Disconnect the B48 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 73 and perform intake system troubleshooting (steps 86 to 88). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 89 to 96).
    4. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)  

59.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    1. If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
    2. Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


60.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the B52 engine coolant temperature sensor connector.

  1. Disconnect the B49 and B48 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B52-2 - B49-17 (THW)
    Always
    Below 1 Ω
    B52-1 - B48-8 (ETHW)
    Always
    Below 1 Ω
    B52-2 or B49-17 (THW) - Body ground
    Always
    10 kΩ or higher
    B52-1 or B48-8 (ETHW) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.
    3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


61.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter .

HINT:
  1. If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
  2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


62.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the B51 mass air flow meter connector.

  1. Disconnect the B48 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B51-5 (VG) - B48-14 (VG)
    Always
    Below 1 Ω
    B51-4 (E2G) - B48-13 (E2G)
    Always
    Below 1 Ω
    B51-5 (VG) or B48-14 (VG) - Body ground
    Always
    10 kΩ or higher

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.
  3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


63.READ VALUE USING TECHSTREAM (LONG FT #1, FT #2 - ATMOSPHERE PRESSURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1, Long FT #2 and Atmosphere Pressure.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    Long FT #2
    +25% or more or less than -25%
    1. Air fuel ratio sensor
    2. Mass air flow meter
    3. Fuel injector assembly
    4. ECM
    A
    Atmosphere Pressure
    80 kPa or less (when altitude is 0 m)
    Both Data List items listed above
    Values are other than above
    -
    B



B
Go to step 67
A


64.PERFORM SIMULATION TEST
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning Value Reset.

  1. Confirm the following conditions as instructed on the screen.

    1. - Ignition switch ON
    2. - Engine stopped
    3. - Battery voltage 9 V or higher

  1. After confirming, select "Next" and initialize the learn value.

  1. After the Techstream display indicates that the learning value reset is complete, turn the ignition switch off and wait for 5 seconds or more.

    NOTICE:
    If a massage indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform learned value initialization again.

  1. Check if the engine can be started.
    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 67
A


65.INSPECT AIR FUEL RATIO SENSOR
A215382E47
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1 and Fuel System Status #2.

  1. Confirm that Fuel System Status #1 and Fuel System Status #2 are both CL.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1.

  1. Confirm that AF Lambda B1S1 are both within the range of 0.95 to 1.05 when idling.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

    Standard Voltage:
    Tester Display
    Injection Volume
    Specified Condition
    AFS Voltage B1S1
    AFS Voltage B2S1
    12.5%
    Air fuel ratio sensor output voltage is below 3.1 V
    -12.5%
    Air fuel ratio sensor output voltage is higher than 3.4 V

    HINT:
    1. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    2. If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
    3. Perform "Inspection After Repair" after replacing the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


66.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine.

    OK:
    Speed is stable.

    HINT:
    1. After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter or fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE MASS AIR FLOW METER (Click here)  

67.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 72
OK


68.INSPECT SPARK PLUG
  1. Inspect the spark plugs .
    Result 
    Result
    Proceed to
    All cylinders are normal
    A
    One cylinder is abnormal*1
    B
    All cylinders are abnormal*2, *3
    C

HINT:
  1. *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
  2. *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
  3. *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.
  4. Perform "Inspection After Repair" after replacing the spark plug (Click here).



B
REPLACE SPARK PLUG (ABNORMAL CYLINDER) (Click here)

C
REPLACE SPARK PLUG (ALL CYLINDERS) (Click here)
A


69.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector assembly leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *4: From step 73, perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.



B
Go to step 71

C
Go to step 73
A


70.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
    Result 
    Result
    Proceed to
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 73, perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.



B
Go to step 73
A

REPLACE PRESSURE REGULATOR (Click here)  

71.CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    4000 ppm or higher
    A
    Less than 4000 ppm
    B*1

    HINT:
    1. If the concentration is 4000 ppm or higher, a fuel injector assembly may have a sealing problem.
    2. *1: From step 73, perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.
    3. Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



B
Go to step 73
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

72.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 73 and perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.



B
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPAIR OR REPLACE FUEL LINE 

73.CHECK MALFUNCTION CONDITION
  1. If the malfunction could not be identified during the inspection in steps 39, 40, 41 and 48, perform fuel system troubleshooting C (steps 74 to 78).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 39, 40, 41 and 48
    Fuel system troubleshooting C
    74 to 78
    A

  1. If the malfunction could not be identified during the inspection in step 46, perform ignition system troubleshooting (steps 79 to 85).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 46
    Ignition system troubleshooting
    79 to 85
    B

  1. If the malfunction could not be identified during the inspection in steps 56, 57 and 58, perform intake air system troubleshooting (steps 86 to 88). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 89 to 96).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 56, 57, 58
    Intake air system troubleshooting
    86 to 88
    C
    Fuel system troubleshooting A
    89 to 96

  1. If the malfunction could not be identified during the inspection in steps 59, 60, 61, 62, 65, 66, 68, 69, 70, 71 and 72, perform fuel system troubleshooting A (steps 97 to 104), fuel system troubleshooting B (steps 105 to 107), intake air system troubleshooting (steps 108 to 110), and ignition system troubleshooting (steps 111 to 117), in that order.

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 59, 60, 61, 62, 65, 66, 68, 69, 70, 71 and 72
    Fuel system troubleshooting A
    97 to 104
    D
    Fuel system troubleshooting B
    105 to 107
    Intake air system troubleshooting
    108 to 110
    Ignition system troubleshooting
    111 to 117



B
Go to step 79

C
Go to step 86

D
Go to step 97
A


74.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


75.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY POWER SOURCE)
A167963E33
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B11-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B25-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B10-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B21-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    B18-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR FUEL INJECTOR ASSEMBLY POWER SOURCE CIRCUIT (Click here)
OK


76.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the B11, B25, B10, B21, B9 and B18 fuel injector assembly connectors.

  1. Disconnect the B50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B11-2 - B50-6 (#10)
    Always
    Below 1 Ω
    B25-2 - B50-1 (#20)
    Always
    Below 1 Ω
    B10-2 - B50-7 (#30)
    Always
    Below 1 Ω
    B21-2 - B50-2 (#40)
    Always
    Below 1 Ω
    B9-2 - B50-8 (#50)
    Always
    Below 1 Ω
    B18-2 - B50-3 (#60)
    Always
    Below 1 Ω
    B11-2 or B50-6 (#10) - Body ground
    Always
    10 kΩ or higher
    B25-2 or B50-1 (#20) - Body ground
    Always
    10 kΩ or higher
    B10-2 or B50-7 (#30) - Body ground
    Always
    10 kΩ or higher
    B21-2 or B50-2 (#40) - Body ground
    Always
    10 kΩ or higher
    B9-2 or B50-8 (#50) - Body ground
    Always
    10 kΩ or higher
    B18-2 - B50-3 (#60) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


77.INSPECT CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 78
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

78.INSPECT VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE) 

79.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


80.CHECK VVT SENSOR
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (Click here)
OK


81.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the B29 crankshaft position sensor connector.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


82.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)
  1. Disconnect the B15 and B27 VVT sensor (for intake side) connectors.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B15-1 (VVR+) - B47-9 (VV1+)
    Always
    Below 1 Ω
    B15-2 (VVR-) - B47-10 (VV1-)
    Always
    Below 1 Ω
    B15-3 (VC) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B27-1 (VVL+) - B47-12 (VV2+)
    Always
    Below 1 Ω
    B27-2 (VVL-) - B47-11 (VV2-)
    Always
    Below 1 Ω
    B27-3 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B15-1 (VVR+) or B47-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B15-2 (VVR-) or B47-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B15-3 (VC) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B27-1 (VVL+) or B47-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B27-2 (VVL-) or B47-11 (VV2-) - Body ground
    Always
    10 kΩ or higher
    B27-3 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


83.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM)
  1. Disconnect the B57 and B58 VVT sensor (for exhaust side) connectors.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) - B47-13 (EV1+)
    Always
    Below 1 Ω
    B57-2 (EX-) - B47-14 (EV1-)
    Always
    Below 1 Ω
    B57-3 (VC2) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B58-1 (EX+) - B47-18 (EV2+)
    Always
    Below 1 Ω
    B58-2 (EX-) - B47-17 (EV2-)
    Always
    Below 1 Ω
    B58-3 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B57-1 (EX+) or B47-13 (EV1+) - Body ground
    Always
    10 kΩ or higher
    B57-2 (EX-) or B47-14 (EV1-) - Body ground
    Always
    10 kΩ or higher
    B57-3 (VC2) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B58-1 (EX+) or B47-18 (EV2+) - Body ground
    Always
    10 kΩ or higher
    B58-2 (EX-) or B47-17 (EV2-) - Body ground
    Always
    10 kΩ or higher
    B58-3 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


84.INSPECT CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 85
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

85.INSPECT VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE) 

86.READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

  1. Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches turned off.


Result 
Data List Item
Result
Suspected Area
Proceed to
ISC Learning Value
(engine displacement (liters) x 0.9) or more
  1. Valve timing
  2. Compression
A
Less than (engine displacement (liters) x 0.9)
-
B


B
Go to step 88
A


87.CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the compression .

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

CHECK VALVE TIMING  

88.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


89.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.
    Result 
    Vehicle State
    Specified Condition
    Cranking engine
    304 to 343 kPa (3.1 to 3.5 kgf/cm2)
    5 minutes after stopping engine
    147 kPa (1.5 kgf/cm2) or more



NG
Go to step 95
OK


90.READ VALUE USING TECHSTREAM (LONG FT #1, FT #2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    Long FT #2
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


91.PERFORM SIMULATION TEST
  1. Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


92.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


93.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the B29 crankshaft position sensor connector.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


94.INSPECT CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

95.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 96
A

REPAIR OR REPLACE FUEL LINE 

96.INSPECT FUEL PUMP
  1. Disconnect the L5 fuel pump connector.



    A074356E41
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (+) - 5 (-)
    20°C (68°F)
    0.2 to 3.0 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Fuel Pump)

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.
  4. Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK

REPLACE PRESSURE REGULATOR (Click here)  

97.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.
    Result 
    Result
    Proceed to
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    A
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    B



B
Go to step 103
A


98.READ VALUE USING TECHSTREAM (LONG FT #1, FT #2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1 and Long FT #2.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    Long FT #2
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B

    HINT:
    Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


99.PERFORM SIMULATION TEST
  1. Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


100.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


101.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the B29 crankshaft position sensor connector.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


102.INSPECT CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

103.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE FUEL PUMP / SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.
    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 104
A

REPAIR OR REPLACE FUEL LINE 

104.INSPECT FUEL PUMP
  1. Disconnect the L5 fuel pump connector.



    A074356E42
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (+) - 5 (-)
    20°C (68°F)
    0.2 to 3.0 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Fuel Pump)

HINT:
  1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
  2. Make sure the internal connector is securely connected.
  3. Make sure the fuel pump filter is not clogged.
  4. Perform "Inspection After Repair" after replacing the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


105.INSPECT PURGE VSV


    A218155
  1. Disconnect the vacuum hose (on the canister side) of the purge VSV.

  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the B53 connector of the purge VSV.

  1. Check if air flows through the purge VSV.

    OK:
    Air does not flow

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
INSPECT PURGE VSV (Click here)
OK


106.CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.
    Result 
    Result
    Proceed to
    4000 ppm or higher
    A
    Less than 4000 ppm
    B

    HINT:
    1. If the concentration is 4000 ppm or higher, a fuel injector assembly may have a sealing problem.
    2. Perform "Inspection After Repair" after replacing the fuel injector assembly (Click here).



B
Go to step 107
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

107.CHECK INTAKE VALVE
  1. Check if carbon is on the intake valves.
    Result 
    Result
    Proceed to
    Carbon present
    A
    No carbon present
    B



B
Go to step 108
A

CLEAN INTAKE VALVE 

108.READ VALUE USING TECHSTREAM (ISC LEARNING VALUE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

  1. Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


Result 
Data List Item
Result
Suspected Area
Proceed to
ISC Learning Value
(engine displacement (liters) x 0.9) or more
  1. Valve timing
  2. Compression
A
Less than (engine displacement (liters) x 0.9)
-
B


B
Go to step 110
A


109.CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the compression .

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly (Click here).



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

CHECK VALVE TIMING  

110.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


111.CHECK CRANKSHAFT POSITION SENSOR
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


112.CHECK VVT SENSOR
  1. Check the tightening and installation condition of the VVT sensor bolt.

  1. Check the connection of the VVT sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL VVT SENSOR (Click here)
OK


113.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the B29 crankshaft position sensor connector.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B29-1 - B47-6 (NE+)
    Always
    Below 1 Ω
    B29-2 - B47-5 (NE-)
    Always
    Below 1 Ω
    B29-1 or B47-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B29-2 or B47-5 (NE-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


114.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE SIDE) - ECM)
  1. Disconnect the B15 and B27 VVT sensor (for intake side) connectors.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B15-1 (VVR+) - B47-9 (VV1+)
    Always
    Below 1 Ω
    B15-2 (VVR-) - B47-10 (VV1-)
    Always
    Below 1 Ω
    B15-3 (VC) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B27-1 (VVL+) - B47-12 (VV2+)
    Always
    Below 1 Ω
    B27-2 (VVL-) - B47-11 (VV2-)
    Always
    Below 1 Ω
    B27-3 (VC) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B15-1 (VVR+) or B47-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B15-2 (VVR-) or B47-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B15-3 (VC) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B27-1 (VVL+) or B47-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B27-2 (VVL-) or B47-11 (VV2-) - Body ground
    Always
    10 kΩ or higher
    B27-3 (VC) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


115.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST SIDE) - ECM)
  1. Disconnect the B57 and B58 VVT sensor (for exhaust side) connectors.

  1. Disconnect the B47 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    B57-1 (EX+) - B47-13 (EV1+)
    Always
    Below 1 Ω
    B57-2 (EX-) - B47-14 (EV1-)
    Always
    Below 1 Ω
    B57-3 (VC2) - B47-15 (VCV1)
    Always
    Below 1 Ω
    B58-1 (EX+) - B47-18 (EV2+)
    Always
    Below 1 Ω
    B58-2 (EX-) - B47-17 (EV2-)
    Always
    Below 1 Ω
    B58-3 (VC2) - B47-16 (VCV2)
    Always
    Below 1 Ω
    B57-1 (EX+) or B47-13 (EV1+) - Body ground
    Always
    10 kΩ or higher
    B57-2 (EX-) or B47-14 (EV1-) - Body ground
    Always
    10 kΩ or higher
    B57-3 (VC2) or B47-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B58-1 (EX+) or B47-18 (EV2+) - Body ground
    Always
    10 kΩ or higher
    B58-2 (EX-) or B47-17 (EV2-) - Body ground
    Always
    10 kΩ or higher
    B58-3 (VC2) or B47-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


116.INSPECT CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 117
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

117.INSPECT VVT SENSOR
  1. Replace the VVT sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (VVT SENSOR IS DEFECTIVE)