After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
This section describes the standard values for all CAN related components.
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 GLOBAL CAN JUNCTION CONNECTOR (for LHD)
| *a | Front view of wire harness connector (to No. 1 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Lane Tracing Assist System *2: w/o Lane Tracing Assist System |
||
|
·
Power steering ECU with motor assembly*1
·
Central gateway ECU (network gateway ECU)*2 |
B66-8 (CANH) | G |
| B66-19 (CANL) | B | |
| Brake booster with master cylinder assembly (No. 1 skid control ECU) | B66-9 (CANH) | P |
| B66-20 (CANL) | B | |
| B66-3 (CANH) | B | |
| B66-14 (CANL) | L | |
| Brake actuator assembly (No. 2 skid controlECU) | B66-10 (CANH) | R |
| B66-21 (CANL) | B | |
| B66-1 (CANH) | BE | |
| B66-12 (CANL) | L | |
| ECM | B66-4 (CANH) | GR |
| B66-15 (CANL) | L | |
| No. 5 global CAN junction connector | B66-7 (CANH) | SB |
| B66-18 (CANL) | B | |
| No. 7 global CAN junction connector | B66-2 (CANH) | R |
| B66-13 (CANL) | L | |
NO. 2 GLOBAL CAN JUNCTION CONNECTOR (for RHD)
| *a | Front view of wire harness connector (to No. 2 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
| Brake booster with master cylinder assembly (No. 1 skid control ECU) | B49-3 (CANH) | P |
| B49-9 (CANL) | B | |
| Brake actuator assembly (No. 2 skid control ECU) | B49-4 (CANH) | R |
| B49-10 (CANL) | B | |
| No. 10 global CAN junction connector | B49-1 (CANH) | SB |
| B49-7 (CANL) | B | |
| Central gateway ECU (network gateway ECU) | B49-2 (CANH) | G |
| B49-8 (CANL) | B |
NO. 3 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 3 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Power Tilt and Power Telescopic Steering Column System *2: w/ Reverse Shift-linked Mirror *3: for LHD *4: w/ Headlight ECU |
||
| Certification ECU (smart key ECU assembly) | I113-3 (CANH) | L |
| I113-13 (CANL) | B | |
| Multiplex tilt and telescopic ECU*1 | I113-4 (CANH) | P |
| I113-14 (CANL) | B | |
| Outer mirror control ECU assembly LH*2 | I113-6 (CANH) | LG |
| I113-16 (CANL) | B | |
| Position control ECU assembly*3 | I113-8 (CANH) | R |
| I113-18 (CANL) | B | |
| Headlight ECU sub-assembly LH*4 | I113-9 (CANH) | W |
| I113-19 (CANL) | B | |
| No. 4 global CAN junction connector | I113-2 (CANH) | P |
| I113-12 (CANL) | B | |
| Central gateway ECU (network gateway ECU) | I113-1 (CANH) | GR |
| I113-11 (CANL) | B | |
NO. 4 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 4 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Reverse Shift-linked Mirror *2: w/ Headlight ECU |
||
| Outer mirror control ECU assembly RH*1 | I114-4 (CANH) | R |
| I114-14 (CANL) | B | |
| Headlight ECU sub-assembly RH*2 | I114-6 (CANH) | W |
| I114-16 (CANL) | B | |
| Air conditioning amplifier assembly | I114-7 (CANH) | L |
| I114-17 (CANL) | B | |
| No. 3 global CAN junction connector | I114-3 (CANH) | P |
| I114-13 (CANL) | B | |
| No. 11 global CAN junction connector | I114-10 (CANH) | LG |
| I114-20 (CANL) | B | |
NO. 5 GLOBAL CAN JUNCTION CONNECTOR (for LHD)
| *a | Front view of wire harness connector (to No. 5 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
| Steering sensor | I166-4 (CANH) | W |
| I166-15 (CANL) | B | |
| Airbag sensor with ECU assembly | I166-5 (CANH) | GR |
| I166-16 (CANL) | B | |
| No. 1 global CAN junction connector | I166-2 (CANH) | SB |
| I166-13 (CANL) | B | |
| Central gateway ECU (network gateway ECU) | I166-3 (CANH) | LG |
| I166-14 (CANL) | B |
NO. 6 GLOBAL CAN JUNCTION CONNECTOR (for LHD)
| *a | Front view of wire harness connector (to No. 6 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display) *2: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) *3: w/ Headup Display System |
||
| Combination meter assembly | I167-1 (CANH) | L |
| I167-12 (CANL) | R | |
| Stereo component equalizer assembly | I167-3 (CANH) | B |
| I167-14 (CANL) | R | |
| Meter mirror sub-assembly*3 | I167-4 (CANH) | G |
| I167-15 (CANL) | R | |
|
·
Radio and display receiver assembly*1
·
Radio receiver assembly*2 |
I167-5 (CANH) | W |
| I167-16 (CANL) | R | |
| No. 9 global CAN junction connector | I167-2 (CANH) | P |
| I167-13 (CANL) | R | |
NO. 6 GLOBAL CAN JUNCTION CONNECTOR (for RHD)
| *a | Front view of wire harness connector (to No. 6 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
| Stereo component equalizer assembly | I117-3 (CANH) | B |
| I117-14 (CANL) | R | |
| No. 9 global CAN junction connector | I117-2 (CANH) | P |
| I117-13 (CANL) | R | |
| Central gateway ECU (network gateway ECU) | I117-1 (CANH) | SB |
| I117-12 (CANL) | R |
NO. 7 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 7 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Stop and Start System *2: w/ Automatic Transmission System (for AJA0F) *3: w/ Adaptive Variable Suspension System *4: for LHD |
||
| No. 1 global CAN junction connector*4 | I118-1 (CANH) | R |
| I118-12 (CANL) | L | |
| ECM | I118-2 (CANH) (for RHD) | B |
| I118-13 (CANL) (for RHD) | W | |
| I118-8 (CANH) (for LHD) | B | |
| I118-19 (CANL) (for LHD) | W | |
| Engine stop and start ECU*1 | I118-5 (CANH) | W |
| I118-16 (CANL) | L | |
| I118-9 (CANH) | L | |
| I118-20 (CANL) | W | |
| TCM*2 | I118-4 (CANH) (for RHD) | R |
| I118-15 (CANL) (for RHD) | W | |
| I118-10 (CANH) (for LHD) | R | |
| I118-21 (CANL) (for LHD) | W | |
| Absorber control ECU*3, *4 | I118-2 (CANH) | V |
| I118-13 (CANL) | L | |
| Central gateway ECU (network gateway ECU) | I118-1 (CANH) (for RHD) | BE |
| I118-12 (CANL) (for RHD) | W | |
| I118-3 (CANH) (for LHD) | B | |
| I118-14 (CANL) (for LHD) | L | |
| I118-7 (CANH) (for LHD) | BE | |
| I118-18 (CANL) (for LHD) | W | |
NO. 8 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 8 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Pre-collision System *2: w/ TOYOTA Parking Assist-sensor System *3: w/ Multi-terrain Monitor System |
||
| Forward recognition camera*1 | I119-4 (CANH) | G |
| I119-14 (CANL) | B | |
| Clearance warning ECU assembly*2 | I119-6 (CANH) | V |
| I119-16 (CANL) | B | |
| Parking assist ECU*3 | I119-7 (CANH) | P |
| I119-17 (CANL) | B | |
| Millimeter wave radar sensor assembly*1 | I119-3 (CANH) | GR |
| I119-13 (CANL) | B | |
| No. 12 global CAN junction connector | I119-2 (CANH) | W |
| I119-12 (CANL) | B | |
| Central gateway ECU (network gateway ECU) | I119-1 (CANH) | SB |
| I119-11 (CANL) | B | |
NO. 9 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 9 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display) *2: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display) *3: for LHD *4: for RHD *5: w/ Telematics System *6: w/ Headup Display System |
||
| Telephone transceiver assembly*3,*5 | I120-3 (CANH) | L |
| I120-14 (CANL) | R | |
| Integration control sub-assembly*2 | I120-5 (CANH) | GR |
| I120-16 (CANL) | R | |
| Combination meter assembly*4 | I120-1 (CANH) | L |
| I120-12 (CANL) | R | |
| Meter mirror sub-assembly*4, *6 | I120-3 (CANH) | G |
| I120-14 (CANL) | R | |
|
·
Radio and display receiver assembly*1, *4
·
Radio receiver assembly*2, *4 |
I120-4 (CANH) | W |
| I120-15 (CANL) | R | |
| No. 6 global CAN junction connector | I120-2 (CANH) | P |
| I120-13 (CANL) | R | |
| Central gateway ECU (network gateway ECU) | I120-1 (CANH) (for LHD) | SB |
| I120-12 (CANL) (for LHD) | R | |
| I120-10 (CANH) | P | |
| I120-21 (CANL) | W | |
| 4 wheel drive control ECU | I120-8 (CANH) | B |
| I120-19 (CANL) | W | |
| Power steering ECU assembly | I120-11 (CANH) | LG |
| I120-22 (CANL) | W | |
| No. 13 global CAN junction connector | I120-9 (CANH) | L |
| I120-20 (CANL) | W | |
NO. 10 GLOBAL CAN JUNCTION CONNECTOR (for RHD)
| *a | Front view of wire harness connector (to No. 10 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Lane Tracing Assist System *2: w/o Lane Tracing Assist System |
||
|
·
Power steering ECU with motor assembly*1
·
No. 1 CAN junction terminal*2 |
I123-2 (CANH) | G*1, P*2 |
| I123-13 (CANL) | B*1, W*2 | |
| Steering sensor | I123-3 (CANH) | W |
| I123-14 (CANL) | B | |
| Airbag sensor with ECU assembly | I123-4 (CANH) | GR |
| I123-15 (CANL) | B | |
| No. 2 global CAN junction connector | I123-1 (CANH) | SB |
| I123-12 (CANL) | B | |
NO. 11 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 11 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Power Back Door Sysem *2: Seat Position Memory System *3: for RHD |
||
| Main body ECU (multiplex network body ECU) | Q62-2 (CANH) | GR |
| Q62-8 (CANL) | B | |
| Multiplex network door ECU*1 | Q62-3 (CANH) | V |
| Q62-9 (CANL) | B | |
| Position control ECU assembly*2, *3 | Q62-4 (CANH) | R |
| Q62-10 (CANL) | B | |
| No. 4 global CAN junction connector | Q62-1 (CANH) | LG |
| Q62-7 (CANL) | B | |
NO. 12 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 12 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*: w/ Blind Spot Moniter System |
||
| Blind spot monitor sensor LH* | Q63-4 (CANH) | L |
| Q63-10 (CANL) | B | |
| Rear television camera assembly | Q63-5 (CANH) | R |
| Q63-11 (CANL) | B | |
| No. 2 CAN junction terminal | Q63-1 (CANH) | SB |
| Q63-7 (CANL) | B | |
| No. 8 global CAN junction connector | Q63-2 (CANH) | W |
| Q63-8 (CANL) | B | |
NO. 13 GLOBAL CAN JUNCTION CONNECTOR
| *a | Front view of wire harness connector (to No. 13 Global CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*1: w/ Tire Pressure Warning System *2: w/ Adaptive Variable Suspension Sysem *3: w/ Electronic-Kinetic Dynamic Suspension System |
||
| Tire pressure warning ECU and receiver*1 | Q64-2 (CANH) | R |
| Q64-13 (CANL) | W | |
| Absorber control ECU*2 | Q64-3 (CANH) | LG |
| Q64-14 (CANL) | W | |
| Stabilizer control ECU*3 | Q64-4 (CANH) | B |
| Q64-15 (CANL) | W | |
| No. 3 CAN junction terminal | Q64-5 (CANH) | P |
| Q64-16 (CANL) | W | |
| No. 9 global CAN junction connector | Q64-1 (CANH) | L |
| Q64-12 (CANL) | W | |
NO. 1 CAN JUNCTION CONNECTOR (for RHD)
| *a | Front view of wire harness connector (to No. 1 CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
|
*: w/ Adaptive Variable Suspention System |
||
| Central gateway ECU (network gateway ECU) | I116-1 (CANH) | B |
| I116-12 (CANL) | L | |
| Absorber control ECU* | I116-3 (CANH) | V |
| I116-14 (CANL) | L | |
| No. 2 CAN junction connector | I116-2 (CANH) | R |
| I116-13 (CANL) | L | |
NO. 2 CAN JUNCTION CONNECTOR (for RHD)
| *a | Front view of wire harness connector (to No. 2 CAN Junction Connector) |
- | - |
| Connected to | Terminal No. (Symbol) | Wiring Color |
|---|---|---|
| Brake booster with master cylinder assembly (No. 1 skid control ECU) | B48-3 (CANH) | B |
| B48-14 (CANL) | L | |
| Brake actuator assembly (No. 2 skid control ECU) | B48-1 (CANH) | BE |
| B48-12 (CANL) | L | |
| ECM | B48-4 (CANH) | GR |
| B48-15 (CANL) | L | |
| No. 1 CAN junction connector | B48-2 (CANH) | R |
| B48-13 (CANL) | L |
NO. 1 CAN JUNCTION TERMINAL (w/o Lane Tracing Assist System)
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to No. 1 CAN Junction Terminal) |
Disconnect the No. 1 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| I100-3 (CANH) | P | No. 10 global CAN junction connector |
| I100-2 (CANL) | W |
NO. 2 CAN JUNCTION TERMINAL
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to No. 2 CAN Junction Terminal) |
Disconnect the No. 2 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| Q58-3 (CANH) | SB | No. 12 global CAN junction connector |
| Q58-2 (CANL) | B |
NO. 3 CAN JUNCTION TERMINAL
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to No. 3 CAN Junction Terminal) |
Disconnect the No. 3 CAN junction terminal connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
| Q59-3 (CANH) | P | No. 13 global CAN junction connector |
| Q59-2 (CANL) | W |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
| *a | Component without harness connected (Central Gateway ECU [Network Gateway ECU]) |
- | - |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the central gateway ECU (network gateway ECU) connector.
| *a | Front view of wire harness connector (to Central Gateway ECU [Network Gateway ECU]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-16 (CA6H) - I42-17 (CA6L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| I42-16 (CA6H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-17 (CA6L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-16 (CA6H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-17 (CA6L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-28 (CA1H) - I42-27 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-28 (CA1H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-27 (CA1L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-28 (CA1H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-27 (CA1L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-26 (CA4H) - I42-25 (CA4L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-26 (CA4H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-25 (CA4L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-26 (CA4H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-25 (CA4L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-30 (CA3H) - I42-29 (CA3L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-30 (CA3H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-29 (CA3L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-30 (CA3H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-29 (CA3L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
|
*1: for RHD *2: for LHD |
|||
| I42-24 (CA2H) - I42-23 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω*1 1MΩ or higher*2 |
| I42-24 (CA2H) - I42-10 (CAVH) | HIGH-level CAN bus line - HIGH-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω*1 |
| I42-23 (CA2L) - I42-11 (CAVL) | LOW-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | Below 1 Ω*1 |
| I42-24 (CA2H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-23 (CA2L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-24 (CA2H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-23 (CA2L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-7 (CA5H) - I42-8 (CA5L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-7 (CA5H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-8 (CA5L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-7 (CA5H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-8 (CA5L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-31 (CA7H) - I42-32 (CA7L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-31 (CA7H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-32 (CA7L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-31 (CA7H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-32 (CA7L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-5 (CA8H) - I42-6 (CA8L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-5 (CA8H) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-6 (CA8L) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-5 (CA8H) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-6 (CA8L) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I42-12 (CAWH) - I42-13 (CAWL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I42-12 (CAWH) - I42-22 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-13 (CAWL) - I42-22 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I42-12 (CAWH) - I42-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I42-13 (CAWL) - I42-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)
Refer to Terminals of ECU.
Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU) |
Disconnect the multiplex tilt and telescopic ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I43-3 (CANP) - I43-11 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I43-3 (CANP) - I43-1 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I43-11 (CANN) - I43-1 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I43-3 (CANP) - I43-2 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I43-11 (CANN) - I43-2 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEERING SENSOR
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Steering Sensor) |
Disconnect the steering sensor connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I51-3 (CANH) - I51-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I51-3 (CANH) - I51-6 (ESS) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I51-8 (CANL) - I51-6 (ESS) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I51-3 (CANH) - I51-4 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I51-8 (CANL) - I51-4 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the clearance warning ECU assembly connector.
| *a | Front view of wire harness connector (to Clearance Warning ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I58-17 (R1) - I58-18 (R2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I58-17 (R1) - I58-31 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I58-18 (R2) - I58-31 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I58-17 (R1) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I58-18 (R2) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIRBAG SENSOR WITH ECU ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the airbag sensor with ECU assembly connector.
| *a | Front view of wire harness connector (to Airbag Sensor with ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I24-26 (CAFH) - I24-27 (CAFL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I24-26 (CAFH) - I24-33 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I24-27 (CAFL) - I24-33 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I24-26 (CAFH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I24-27 (CAFL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POWER STEERING ECU ASSEMBLY
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the power steering ECU assembly connector.
| *a | Front view of wire harness connector (to Power Steering ECU Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I29-1 (CANH) - I29-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I29-1 (CANH) - I29-3 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I29-2 (CANL) - I29-3 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I29-1 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I29-2 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I33-2 (CANH) - I33-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I33-2 (CANH) - I33-17 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I33-1 (CANL) - I33-17 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I33-2 (CANH) - I33-5 (B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I33-1 (CANL) - I33-5 (B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I5-13 (CANH) - I5-29 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I5-13 (CANH) - I5-1 (EP) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I5-29 (CANL) - I5-1 (EP) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I5-13 (CANH) - I5-5 (B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I5-29 (CANL) - I5-5 (B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Certification ECU [Smart Key ECU Assembly]) |
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I39-1 (CANH) - I39-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I39-1 (CANH) - I39-29 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-2 (CANL) - I39-29 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I39-1 (CANH) - I39-6 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I39-2 (CANL) - I39-6 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
w/ Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
w/o Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the main body ECU (multiplex network body ECU) connector.
| *a | Front view of wire harness connector (to Main Body ECU [Multiplex Network Body ECU]) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I3-2 (CANH) - I3-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I3-2 (CANH) - I76-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I3-1 (CANL) - I76-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I3-2 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I3-1 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
4 WHEEL DRIVE CONTROL ECU
Refer to Terminals of ECU.
Click hereDrivetrain>JF2BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the 4 wheel drive control ECU connectors.
| *a | Front view of wire harness connector (to 4 Wheel Drive Control ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B9-6 (CANH) - B9-7 (CANH) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B9-6 (CANH) - B10-1 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B9-7 (CANH) - B10-1 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B9-6 (CANH) - B9-8 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B9-7 (CANH) - B9-8 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TCM (w/ Automatic Transmission System (for AJA0F))
Refer to Terminals of ECU.
for V35A-FTS: Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>TERMINALS OF ECU
for F33A-FTV: Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to TCM) |
Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| C36-20 (CANH) - C36-21 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| C36-20 (CANH) - C36-2 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C36-21 (CANL) - C36-2 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C36-20 (CANH) - C36-41 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| C36-21 (CANL) - C36-41 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM (for 1GR-FE)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B2-11 (CANH) - B2-19 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| B2-11 (CANH) - B2-52 (EC) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B2-19 (CANL) - B2-52 (EC) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B2-11 (CANH) - B2-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B2-19 (CANL) - B2-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B2-10 (CANP) - B2-18 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B2-10 (CANP) - B2-52 (EC) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B2-18 (CANN) - B2-52 (EC) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B2-10 (CANP) - B2-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B2-18 (CANN) - B2-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM (for V35A-FTS)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B1-18 (CANH) - B1-17 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| B1-18 (CANH) - B1-9 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B1-17 (CANL) - B1-9 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B1-18 (CANH) - B1-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B1-17 (CANL) - B1-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B1-16 (CACH) - B1-15 (CACL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B1-16 (CACH) - B1-9 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B1-15 (CACL) - B1-9 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B1-16 (CACH) - B1-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B1-15 (CACL) - B1-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ECM (for F33A-FTV)
Refer to Terminals of ECU.
w/ DPF: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>TERMINALS OF ECM
w/o DPF: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>TERMINALS OF ECM
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B70-7 (CANH) - B70-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| B70-7 (CANH) - B70-10 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B70-8 (CANL) - B70-10 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B70-7 (CANH) - B70-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B70-8 (CANL) - B70-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B70-17 (CACH) - B70-18 (CACL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B70-17 (CACH) - B70-10 (E1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B70-18 (CACL) - B70-10 (E1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B70-17 (CACH) - B70-1 (BATT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B70-18 (CACL) - B70-1 (BATT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ABSORBER CONTROL ECU (w/ Adaptive Variable Suspension System)
Refer to Terminals of ECU.
Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the absorber control ECU connector.
| *a | Front view of wire harness connector (to Absorber Control ECU) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| Q11-8 (CANH) - Q11-7 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Q11-8 (CANH) - Q11-4 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q11-7 (CANL) - Q11-4 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q11-8 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q11-7 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| Q11-19 (CA2H) - Q11-18 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Q11-19 (CA2H) - Q11-4 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q11-18 (CA2L) - Q11-4 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q11-19 (CA2H) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q11-18 (CA2L) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STABILIZER CONTROL ECU (w/ Electronic-Kinetic Dynamic Suspension System)
Refer to Terminals of ECU.
Click hereSuspension>SUSPENSION CONTROL>ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Stabilizer Control ECU) |
Disconnect the stabilizer control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| Q14-8 (CANH) - Q14-7 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Q14-8 (CANH) - Q14-4 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q14-7 (CANL) - Q14-4 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| Q14-8 (CANH) - Q14-1 (IGB) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Q14-7 (CANL) - Q14-1 (IGB) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RADIO RECEIVER ASSEMBLY (w/ Audio and Visual System for Radio and Display Type, for 12.3 Inch Display)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the radio receiver assembly connectors.
| *a | Front view of wire harness connector (to Radio Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I12-13 (CANH) - I12-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I12-13 (CANH) - I10-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-14 (CANL) - I10-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-13 (CANH) - I10-4 (+B1) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I12-14 (CANL) - I10-4 (+B1) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
RADIO AND DISPLAY RECEIVER (w/ Audio and Visual System for Radio and Display Type, except 12.3 Inch Display)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the radio and display receiver assembly connectors.
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I13-13 (CANH) - I13-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I13-13 (CANH) - I11-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-14 (CANL) - I11-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-13 (CANH) - I11-4 (+B1) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I13-14 (CANL) - I11-4 (+B1) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
INTEGRATION CONTROL SUB-ASSEMBLY (for Radio and Display Type, for 12.3 Inch Display)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Integration Control Sub-assembly) |
Disconnect the integration control sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I22-32 (CANP) - I22-31 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I22-32 (CANP) - I22-20 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I22-31 (CANN) - I22-20 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I22-32 (CANP) - I22-1 (B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I22-31 (CANN) - I22-1 (B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the blind spot monitor sensor LH connectors.
| *a | Front view of wire harness connector (to Blind Spot Monitor Sensor LH) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| T10-2 (CA1P) - T10-7 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| T10-2 (CA1P) - T10-10 (BLGD) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T10-7 (CA1N) - T10-10 (BLGD) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T10-2 (CA1P) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| T10-7 (CA1N) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)
Refer to Terminals of ECU.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the multiplex network door ECU connectors.
| *a | Front view of wire harness connector (to Multiplex Network Door ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| T1-10 (CANP) - T1-20 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| T1-10 (CANP) - T3-4 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T1-20 (CANN) - T3-4 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T1-10 (CANP) - T1-7 (ECUB) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| T1-20 (CANN) - T1-7 (ECUB) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Reverse Shift-linked Mirror)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Outer Mirror Control ECU Assembly RH) |
Disconnect the outer mirror control ECU assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| M1-9 (CANP) - M1-8 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| M1-9 (CANP) - M1-7 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M1-8 (CANN) - M1-7 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| M1-9 (CANP) - M1-6 (CPUB) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M1-8 (CANN) - M1-6 (CPUB) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Reverse Shift-linked Mirror)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Outer Mirror Control ECU Assembly LH) |
Disconnect the outer mirror control ECU assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| N1-9 (CANP) - N1-8 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| N1-9 (CANP) - N1-7 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N1-8 (CANN) - N1-7 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| N1-9 (CANP) - N1-6 (CPUB) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| N1-8 (CANN) - N1-6 (CPUB) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System for Type A)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL SYSTEM (for Type A)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Stereo Component Equalizer Assembly) |
Disconnect the stereo component equalizer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| S20-1 (CANH) - S20-15 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| S20-1 (CANH) - S20-28 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S20-15 (CANL) - S20-28 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S20-1 (CANH) - S20-14 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S20-15 (CANL) - S20-14 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System for Type B)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL SYSTEM (for Type B)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Stereo Component Equalizer Assembly) |
Disconnect the stereo component equalizer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| S25-1 (CANH) - S25-16 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| S25-1 (CANH) - S25-30 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S25-16 (CANL) - S25-30 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S25-1 (CANH) - S25-15 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S25-16 (CANL) - S25-15 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR (w/ Pre-collision System)
Refer to Terminals of ECU.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the millimeter wave radar sensor assembly connectors.
| *a | Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A10-3 (CA2H) - A10-2 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A10-3 (CA2H) - A10-1 (SGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A10-2 (CA2L) - A10-1 (SGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A10-3 (CA2H) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A10-2 (CA2L) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the rear television camera assembly connectors.
| *a | Front view of wire harness connector (to Rear Television Camera Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| g18-1 (CANH) - g18-2 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| g18-1 (CANH) - I76- 4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| g18-2 (CANL) - I76- 4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| g18-1 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| g18-2 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the rear television camera assembly connectors.
| *a | Front view of wire harness connector (to Rear Television Camera Assembly) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| g9-4 (CANH) - g9-1 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| g9-4 (CANH) - I76-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| g9-1 (CANL) - I76-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| g9-4 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| g9-1 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
FORWARD RECOGNITION CAMERA (w/ Pre-collision System)
Refer to Terminals of ECU.
Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the forward recognition camera connectors.
| *a | Front view of wire harness connector (to Forward Recognition Camera) |
*b | Front view of DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| d20-5 (CA1P) - d20-11 (CA1N) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| d20-5 (CA1P) - d20-10 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| d20-11 (CA1N) - d20-10 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| d20-5 (CA1P) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| d20-11 (CA1N) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)
Refer to Terminals of ECU.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Tire Pressure Warning ECU and Receiver) |
Disconnect the tire pressure warning ECU and receiver connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| T11-9 (CANH) - T11-10 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| T11-9 (CANH) - T11-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T11-10 (CANL) - T11-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T11-9 (CANH) - T11-7 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| T11-10 (CANL) - T11-7 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the position control ECU assembly connector.
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector (to Position Control ECU Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| i19-13 (CANP) - i19-14 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| i19-13 (CANP) - i17-2 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| i19-14 (CANN) - i17-2 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| i19-13 (CANP) - i19-15 (SYSB) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| i19-14 (CANN) - i19-15 (SYSB) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| h24-13 (CANP) - h24-14 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| h24-13 (CANP) - h22-2 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| h24-14 (CANN) - h22-2 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| h24-13 (CANP) - h24-15 (SYSB) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| h24-14 (CANN) - h24-15 (SYSB) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)
Refer to Terminals of ECU.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Meter Mirror Sub-assembly) |
Disconnect the meter mirror sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I17-12 (MPX1) - I17-13 (MPX2) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I17-12 (MPX1) - I17-4 (ES) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I17-13 (MPX2) - I17-4 (ES) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I17-12 (MPX1) - I17-2 (B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I17-13 (MPX2) - I17-2 (B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
PARKING ASSIST ECU (w/ Multi-terrain Monitor System)
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I60-11 (CANH) - I60-12 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I60-11 (CANH) - I60-4 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I60-12 (CANL) - I60-4 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I60-11 (CANH) - I60-1 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I60-12 (CANL) - I60-1 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Headlight ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Headlight ECU Sub-assembly LH) |
| *b | Front view of DLC3 |
Disconnect the headlight ECU sub-assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B4-24 (CANH) - B4-23 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B4-24 (CANH) - B4-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B4-23 (CANL) - B4-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B4-24 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B4-23 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Headlight ECU)
Refer to Terminals of ECU.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Headlight ECU Sub-assembly RH) |
| *b | Front view of DLC3 |
Disconnect the headlight ECU sub-assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B7-24 (CANH) - B7-23 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B7-24 (CANH) - B7-12 (GND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B7-23 (CANL) - B7-12 (GND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B7-24 (CANH) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B7-23 (CANL) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Brake Actuator Assembly (No.2 Skid Control ECU)) |
Disconnect the brake actuator assembly (No. 2 skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B20-27 (CANH) - B20-43 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B20-27 (CANH) - B20-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B20-43 (CANL) - B20-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B20-27 (CANH) - B20-14 (+BS) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B20-43 (CANL) - B20-14 (+BS) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B20-16 (CA2H) - B20-17 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| B20-16 (CA2H) - B20-1 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B20-17 (CA2L) - B20-1 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B20-16 (CA2H) - B20-14 (+BS) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B20-17 (CA2L) - B20-14 (+BS) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU)) |
Disconnect the brake booster with master cylinder assembly (No. 1 skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B19-38 (CA1H) - B19-39 (CA1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B19-38 (CA1H) - B19-28 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B19-39 (CA1L) - B19-28 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B19-38 (CA1H) - B19-14 (+BI1) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B19-39 (CA1L) - B19-14 (+BI1) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| B19-35 (CA2H) - B19-36 (CA2L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| B19-35 (CA2H) - B19-28 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B19-36 (CA2L) - B19-28 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| B19-35 (CA2H) - B19-14 (+BI1) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| B19-36 (CA2L) - B19-14 (+BI1) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System)
Refer to Terminals of ECU.
for ERA-GLONASS: Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>TERMINALS OF ECU
for eCall: Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
for Toyota Connected Services: Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the telephone transceiver assembly connector.
| *a | Front view of wire harness connector (to Telephone Transceiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I55-25 (CANP) - I55-26 (CANN) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I55-25 (CANP) - I55-20 (E) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I55-26 (CANN) - I55-20 (E) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I55-25 (CANP) - I55-1 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I55-26 (CANN) - I55-1 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
POWER STEERING ECU WITH MOTOR ASSEMBLY (w/ Lane Tracing Assist System)
Refer to Terminals of ECU.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector (to Power Steering ECU with Motor Assembly) |
Disconnect the power steering ECU with motor assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I71-7 (CANH) - I71-8 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I71-7 (CANH) - I70-2 (PGND) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I71-8 (CANL) - I70-20 (PGND) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I71-7 (CANH) - I71-1 (IG) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I71-8 (CANL) - I71-1 (IG) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
ENGINE STOP AND START ECU (w/ Stop and Start System)
Refer to Terminals of ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
Disconnect the cable from the negative (-) battery terminal.
Disconnect the engine stop and start ECU connectors.
| *a | Front view of wire harness connector (to Engine Stop and Start ECU) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I57-13 (CANH) - I57-14 (CANL) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I57-13 (CANH) - B37-8 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I57-14 (CANL) - B37-8 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I57-13 (CANH) - B38-1 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I57-14 (CANL) - B38-1 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I57-15 (LC1H) - I57-16 (LC1L) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I57-15 (LC1H) - B37-8 (GND1) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I57-16 (LC1L) - B37-8 (GND1) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I57-15 (LC1H) - B38-1 (+B) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I57-16 (LC1L) - B38-1 (+B) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
OPTION CONNECTOR (BUS BUFFER ECU)
Disconnect the cable from the negative (-) battery terminal.
Disconnect the option connector (bus buffer ECU) connectors.
| *a | Front view of wire harness connector (to Option Connector (Bus Buffer ECU)) |
*B | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| I96-2 (CAN+) - I96-1 (CAN-) | HIGH-level CAN bus line - LOW-level CAN bus line | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| I96-2 (CAN+) - I76-4 (CG) | HIGH-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I96-1 (CAN-) - I76-4 (CG) | LOW-level CAN bus line - Ground | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I96-2 (CAN+) - I76-16 (BAT) | HIGH-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I96-1 (CAN-) - I76-16 (BAT) | LOW-level CAN bus line - battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |