Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2022.11
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467519 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 GLOBAL CAN JUNCTION CONNECTOR (for LHD)


C422306C46
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false B66
*a Front view of wire harness connector
(to No. 1 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Lane Tracing Assist System

*2: w/o Lane Tracing Assist System

Brake actuator assembly (No. 2 skid controlECU) B66-1 (CANH) BE
B66-12 (CANL) L
No. 7 global CAN junction connector B66-2 (CANH) R
B66-13 (CANL) L
Brake booster with master cylinder assembly (No. 1 skid control ECU) B66-3 (CANH) B
B66-14 (CANL) L
ECM B66-4 (CANH) GR
B66-15 (CANL) L
No. 5 global CAN junction connector B66-7 (CANH) SB
B66-18 (CANL) BE
·

Power steering ECU with motor assembly*1

·

Central gateway ECU (network gateway ECU)*2


B66-8 (CANH) G
B66-19 (CANL) BE
Brake booster with master cylinder assembly (No. 1 skid control ECU) B66-9 (CANH) P
B66-20 (CANL) BE
Brake actuator assembly (No. 2 skid controlECU) B66-10 (CANH) R
B66-21 (CANL) BE


NO. 2 GLOBAL CAN JUNCTION CONNECTOR (for RHD)


C422306C84
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false B86
*a Front view of wire harness connector
(to No. 2 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Lane Tracing Assist System

*2: w/o Lane Tracing Assist System

No. 5 global CAN junction connector B86-8 (CANH) SB
B86-19 (CANL) BE
·

Power steering ECU with motor assembly*1

·

Central gateway ECU (network gateway ECU)*2


B86-9 (CANH) G
B86-20 (CANL) BE
Brake booster with master cylinder assembly (No. 1 skid control ECU) B86-10 (CANH) P
B86-21 (CANL) BE
Brake actuator assembly (No. 2 skid control ECU) B86-11 (CANH) R
B86-22 (CANL) BE


NO. 5 GLOBAL CAN JUNCTION CONNECTOR (for LHD)


C422306C85
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false I181
*a Front view of wire harness connector
(to No. 5 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Pre-collision System

*2: w/ TOYOTA Parking Assist-sensor System

*3: w/ Multi-terrain Monitor System

Central gateway ECU (network gateway ECU) I181-1 (CANH) SB
I181-12 (CANL) B
No. 12 global CAN junction connector I181-2 (CANH) W
I181-13 (CANL) B
Forward recognition camera*1 I181-3 (CANH) G
I181-14 (CANL) B
Clearance warning ECU assembly*2 I181-4 (CANH) V
I181-15 (CANL) B
Parking assist ECU*3 I181-5 (CANH) P
I181-16 (CANL) B
No. 1 global CAN junction connector I181-8 (CANH) SB
I181-19 (CANL) BE
Central gateway ECU (network gateway ECU) I181-9 (CANH) LG
I181-20 (CANL) BE
Steering sensor I181-10 (CANH) W
I181-21 (CANL) BE
Airbag ECU assembly I181-11 (CANH) GR
I181-22 (CANL) BE


NO. 5 GLOBAL CAN JUNCTION CONNECTOR (for RHD)


C422306C86
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.74 1.708,0.938 0.458,0.198 10 false I185
*a Front view of wire harness connector
(to No. 5 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Pre-collision System

*2: w/ TOYOTA Parking Assist-sensor System

*3: w/ Multi-terrain Monitor System

Central gateway ECU (network gateway ECU) I185-1 (CANH) SB
I185-12 (CANL) B
No. 12 global CAN junction connector I185-2 (CANH) W
I185-13 (CANL) B
Forward recognition camera*1 I185-3 (CANH) G
I185-14 (CANL) B
Clearance warning ECU assembly*2 I185-4 (CANH) V
I185-15 (CANL) B
Parking assist ECU*3 I185-5 (CANH) P
I185-16 (CANL) B
No. 2 global CAN junction connector I185-8 (CANH) SB
I185-19 (CANL) BE
Central gateway ECU (network gateway ECU) I185-9 (CANH) LG
I185-20 (CANL) BE
Steering sensor I185-10 (CANH) W
I185-21 (CANL) BE
Airbag ECU assembly I185-11 (CANH) GR
I185-22 (CANL) BE


NO. 6 GLOBAL CAN JUNCTION CONNECTOR (for LHD)


C422306C87
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.74 1.708,0.938 0.458,0.198 10 false I182
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Power Tilt and Power Telescopic Steering Column System

*2: w/ Reverse Shift-linked Mirror

*3: w/ Power Back Door System

*4: w/ Headlight ECU

Central gateway ECU (network gateway ECU) I182-1 (CANH) SB
I182-12 (CANL) B
No. 9 global CAN junction connector I182-2 (CANH) W
I182-13 (CANL) B
Certification ECU (smart key ECU assembly) I182-3 (CANH) L
I182-14 (CANL) B
Multiplex tilt and telescopic ECU*1 I182-4 (CANH) P
I182-15 (CANL) B
Outer mirror control ECU assembly LH*2 I182-5 (CANH) LG
I182-16 (CANL) B
Multiplex network door ECU*3 I182-6 (CANH) V
I182-17 (CANL) B
Headlight ECU sub-assembly LH*4 I182-7 (CANH) BE
I182-18 (CANL) W
No. 9 global CAN junction connector I182-8 (CANH) G
I182-19 (CANL) W
Central gateway ECU (network gateway ECU) I182-9 (CANH) P
I182-20 (CANL) W
4 wheel drive control ECU I182-10 (CANH) B
I182-21 (CANL) W
Power steering ECU assembly I182-11 (CANH) LG
I182-22 (CANL) W


NO. 6 GLOBAL CAN JUNCTION CONNECTOR (for RHD)


C422306C92
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.26,0.76 1.719,0.958 0.458,0.198 10 false I177
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Power Tilt and Power Telescopic Steering Column System

*2: w/ Reverse Shift-linked Mirror

*3: w/ Power Back Door System

*4: w/ Headlight ECU

Central gateway ECU (network gateway ECU) I177-1 (CANH) GR
I177-12 (CANL) B
No. 9 global CAN junction connector I177-2 (CANH) W
I177-13 (CANL) B
Certification ECU (smart key ECU assembly) I177-3 (CANH) L
I177-14 (CANL) B
Multiplex tilt and telescopic ECU*1 I177-4 (CANH) P
I177-15 (CANL) B
Outer mirror control ECU assembly LH*2 I177-5 (CANH) LG
I177-16 (CANL) B
Multiplex network door ECU*3 I177-6 (CANH) V
I177-17 (CANL) B
Headlight ECU sub-assembly LH*4 I177-7 (CANH) BE
I177-18 (CANL) B
No. 9 global CAN junction connector I177-8 (CANH) G
I177-19 (CANL) W
Central gateway ECU (network gateway ECU) I177-9 (CANH) P
I177-20 (CANL) W
4 wheel drive control ECU I177-10 (CANH) B
I177-21 (CANL) W


NO. 7 GLOBAL CAN JUNCTION CONNECTOR


C422306C88
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false I178
*a Front view of wire harness connector
(to No. 7 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Stop and Start System

*2: w/ Automatic Transmission System (for AJA0F)

*3: w/ Adaptive Variable Suspension System

*4: for LHD

*5: for RHD

Central gateway ECU (network gateway ECU) I178-1 (CANH) BE
I178-12 (CANL) W
ECM I178-2 (CANH) B
I178-13 (CANL) W
Engine stop and start ECU*1 I178-3 (CANH) L
I178-14 (CANL) W
TCM*2 I178-4 (CANH) R
I178-15 (CANL) W
Central gateway ECU (network gateway ECU) I178-8 (CANH) B
I178-19 (CANL) L
·

No. 1 global CAN junction connector*4

·

No. 2 CAN junction connector*5


I178-9 (CANH) R
I178-20 (CANL) L
Absorber control ECU*3 I178-10 (CANH) V
I178-21 (CANL) L
Engine stop and start ECU*1 I178-11 (CANH) W
I178-22 (CANL) L


NO. 9 GLOBAL CAN JUNCTION CONNECTOR


C422306C89
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false I179
*a Front view of wire harness connector
(to No. 9 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Reverse Shift-linked Mirror

*2: w/ Headlight ECU

*3: w/ Seat Position Memory System

*4: for LHD

*5: for RHD

No. 6 global CAN junction connector I179-1 (CANH) W
I179-12 (CANL) B
Outer mirror control ECU assembly RH*1 I179-2 (CANH) R
I179-13 (CANL) B
Position control ECU assembly*3, *5 I179-3 (CANH) BE
I179-14 (CANL) B
Main body ECU (multiplex network body ECU) I179-4 (CANH) LG
I179-15 (CANL) B
Position control ECU assembly*3, *4 I179-5 (CANH) G
I179-16 (CANL) B
Headlight ECU sub-assembly RH*2 I179-7 (CANH) GR
I179-18 (CANL) W
No. 6 global CAN junction connector I179-8 (CANH) G
I179-19 (CANL) W
No. 13 global CAN junction connector I179-9 (CANH) L
I179-20 (CANL) W
Air conditioning amplifier assembly I179-10 (CANH) V
I179-21 (CANL) W
Power steering ECU assembly*5 I179-11 (CANH) LG
I179-22 (CANL) W


NO. 12 GLOBAL CAN JUNCTION CONNECTOR


C435672C63
1.438,1.271 1.844,1.5 0.406,0.229 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.521,1.313 2.115,1.615 0.594,0.302 10 false Q63
*a Front view of wire harness connector
(to No. 12 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Blind Spot Moniter System

*2: w/ Pre-collision System

No. 2 CAN junction terminal Q63-1 (CANH) SB
Q63-7 (CANL) B
No. 5 global CAN junction connector Q63-2 (CANH) W
Q63-8 (CANL) B
Millimeter wave radar sensor assembly*2 Q63-3 (CANH) GR
Q63-9 (CANL) B
Blind spot monitor sensor LH*1 Q63-4 (CANH) L
Q63-10 (CANL) B
Rear television camera assembly Q63-5 (CANH) R
Q63-11 (CANL) B


NO. 13 GLOBAL CAN JUNCTION CONNECTOR


C422306C40
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.76 1.708,0.958 0.458,0.198 10 false Q64
*a Front view of wire harness connector
(to No. 13 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Tire Pressure Warning System

*2: w/ Adaptive Variable Suspension Sysem

*3: w/ Electronic-Kinetic Dynamic Suspension System

No. 9 global CAN junction connector Q64-1 (CANH) L
Q64-12 (CANL) W
Tire pressure warning ECU and receiver*1 Q64-2 (CANH) R
Q64-13 (CANL) W
Absorber control ECU*2 Q64-3 (CANH) LG
Q64-14 (CANL) W
Stabilizer control ECU*3 Q64-4 (CANH) B
Q64-15 (CANL) W
No. 3 CAN junction terminal Q64-5 (CANH) P
Q64-16 (CANL) W


NO. 14 GLOBAL CAN JUNCTION CONNECTOR


C422306C91
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false I180
*a Front view of wire harness connector
(to No. 14 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Audio and Visual System (for Radio and Display Type, except 12.3 Inch Display)

*2: w/ Audio and Visual System (for Radio and Display Type, for 12.3 Inch Display)

*3: w/ Telematics System

*4: w/ Headup Display System

Central gateway ECU (network gateway ECU) I180-1 (CANH) SB
I180-12 (CANL) R
Telephone transceiver assembly*3 I180-2 (CANH) L
I180-13 (CANL) R
Meter mirror sub-assembly*4 I180-3 (CANH) G
I180-14 (CANL) R
Integration control sub-assembly*2 I180-4 (CANH) GR
I180-15 (CANL) R
·

Radio and display receiver assembly*1

·

Radio receiver assembly*2


I180-9 (CANH) W
I180-20 (CANL) R
Combination meter assembly I180-10 (CANH) P
I180-21 (CANL) R
Stereo component equalizer assembly I180-11 (CANH) B
I180-22 (CANL) R


NO. 2 CAN JUNCTION CONNECTOR (for RHD)


C422306C33
1.135,0.708 1.635,0.958 0.5,0.25 0.271,0.083 0.583,0.24 0.313,0.156 10 false *a 1.25,0.75 1.708,0.948 0.458,0.198 10 false B48
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
Brake booster with master cylinder assembly (No. 1 skid control ECU) B48-3 (CANH) B
B48-14 (CANL) L
Brake actuator assembly (No. 2 skid control ECU) B48-1 (CANH) BE
B48-12 (CANL) L
ECM B48-4 (CANH) GR
B48-15 (CANL) L
No. 7 Global CAN junction connector B48-2 (CANH) R
B48-13 (CANL) L


NO. 2 CAN JUNCTION TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453185C06
1.469,0.229 2.01,0.521 0.542,0.292 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 1.594,0.292 2.052,0.521 0.458,0.229 10 false Q58
*a Front view of wire harness connector
(to No. 2 CAN Junction Terminal)


Disconnect the No. 2 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Connected to
Q58-3 (CANH) SB No. 12 global CAN junction connector
Q58-2 (CANL) B




NO. 3 CAN JUNCTION TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453185C07
1.469,0.229 2.01,0.521 0.542,0.292 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 1.594,0.292 2.052,0.521 0.458,0.229 10 false Q59
*a Front view of wire harness connector
(to No. 3 CAN Junction Terminal)


Disconnect the No. 3 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Connected to
Q59-3 (CANH) P No. 13 global CAN junction connector
Q59-2 (CANL) W




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C422307C15
3.49,0.135 3.906,0.385 0.417,0.25 0.188,0.198 0.5,0.396 0.313,0.198 10 false *a 3.604,0.177 4.063,0.375 0.458,0.198 10 false I42
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.

C422308C28
0.802,0.844 1.354,1.135 0.552,0.292 1.01,0.906 1.469,1.104 0.458,0.198 10 false I42 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines (DLC3 - Central Gateway ECU [Network Gateway ECU])
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-16 (CA6H) - I42-17 (CA6L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
I42-16 (CA6H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-17 (CA6L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-16 (CA6H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-17 (CA6L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-28 (CA1H) - I42-27 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-28 (CA1H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-27 (CA1L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-28 (CA1H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-27 (CA1L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-26 (CA4H) - I42-25 (CA4L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-26 (CA4H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-25 (CA4L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-26 (CA4H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-25 (CA4L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-30 (CA3H) - I42-29 (CA3L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-30 (CA3H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-29 (CA3L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-30 (CA3H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-29 (CA3L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition

*1: w/ Lane Tracing Assist System

*2: w/o Lane Tracing Assist System

I42-24 (CA2H) - I42-23 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω*1
1MΩ or higher*2
I42-24 (CA2H) - I42-10 (CAVH) HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω*1
I42-23 (CA2L) - I42-11 (CAVL) LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω*1
I42-24 (CA2H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-23 (CA2L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-24 (CA2H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-23 (CA2L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-7 (CA5H) - I42-8 (CA5L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-7 (CA5H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-8 (CA5L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-7 (CA5H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-8 (CA5L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 6 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-31 (CA7H) - I42-32 (CA7L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-31 (CA7H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-32 (CA7L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-31 (CA7H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-32 (CA7L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 7 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-5 (CA8H) - I42-6 (CA8L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-5 (CA8H) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-6 (CA8L) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-5 (CA8H) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-6 (CA8L) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I42-12 (CAWH) - I42-13 (CAWL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I42-12 (CAWH) - I42-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-13 (CAWL) - I42-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I42-12 (CAWH) - I42-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I42-13 (CAWL) - I42-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic Steering Column System)


Refer to Terminals of ECU.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453189C05
1.51,0.271 2,0.573 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.677,0.333 2.135,0.531 0.458,0.198 10 false I43
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the multiplex tilt and telescopic ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I43-3 (CANP) - I43-11 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I43-3 (CANP) - I43-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I43-11 (CANN) - I43-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I43-3 (CANP) - I43-2 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I43-11 (CANN) - I43-2 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C454958C04
1.531,0.646 1.958,0.927 0.427,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.656,0.719 2.115,0.917 0.458,0.198 10 false I51
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I51-3 (CANH) - I51-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I51-3 (CANH) - I51-6 (ESS) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-8 (CANL) - I51-6 (ESS) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I51-3 (CANH) - I51-4 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I51-8 (CANL) - I51-4 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.

C406371C23
5.042,0.354 5.552,0.667 0.51,0.313 1.719,0.365 2.229,0.677 0.51,0.313 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 4.021,0.125 4.333,0.323 0.313,0.198 10 false *b 1.865,0.448 2.323,0.646 0.458,0.198 10 false I58 5.198,0.448 5.656,0.646 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I58-17 (R1) - I58-18 (R2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I58-17 (R1) - I58-31 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-18 (R2) - I58-31 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I58-17 (R1) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I58-18 (R2) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the airbag ECU assembly connector.

C409697C09
2.115,0.146 2.594,0.438 0.479,0.292 5.427,0.542 5.906,0.833 0.479,0.292 0.74,0.271 1.052,0.469 0.313,0.198 10 false *a 4.396,0.323 4.708,0.521 0.313,0.198 10 false *b 2.271,0.229 2.729,0.427 0.458,0.198 10 false I24 5.542,0.594 6,0.792 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I24-26 (CAFH) - I24-27 (CAFL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I24-26 (CAFH) - I24-33 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I24-27 (CAFL) - I24-33 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I24-26 (CAFH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I24-27 (CAFL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.

C460321C01
2.052,0.438 2.5,0.667 0.448,0.229 5.385,0.604 5.833,0.833 0.448,0.229 0.615,0.563 0.927,0.719 0.313,0.156 10 false *a 4.396,0.542 4.708,0.698 0.313,0.156 10 false *b 2.208,0.479 2.667,0.677 0.458,0.198 10 false I29 5.542,0.635 6,0.833 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I29-1 (CANH) - I29-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I29-1 (CANH) - I29-3 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I29-2 (CANL) - I29-3 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I29-1 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I29-2 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453193C04
1.458,0.104 1.948,0.406 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.604,0.198 2.063,0.396 0.458,0.198 10 false I33
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I33-2 (CANH) - I33-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I33-2 (CANH) - I33-17 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I33-1 (CANL) - I33-17 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I33-2 (CANH) - I33-5 (B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I33-1 (CANL) - I33-5 (B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406366C82
1.51,0.125 2,0.427 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.708,0.198 2.021,0.396 0.313,0.198 10 false I5
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I5-13 (CANH) - I5-29 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I5-13 (CANH) - I5-1 (EP) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I5-29 (CANL) - I5-1 (EP) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I5-13 (CANH) - I5-5 (B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I5-29 (CANL) - I5-5 (B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C422313C09
1.51,0.063 2,0.365 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.667,0.156 2.125,0.354 0.458,0.198 10 false I39
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I39-1 (CANH) - I39-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I39-1 (CANH) - I39-29 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-2 (CANL) - I39-29 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I39-1 (CANH) - I39-6 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I39-2 (CANL) - I39-6 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

w/ Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU

w/o Headlight ECU: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/o Headlight ECU)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.

C458821C01
1.917,0.25 2.417,0.5 0.5,0.25 5.417,0.583 5.917,0.833 0.5,0.25 0.646,0.354 0.958,0.51 0.313,0.156 10 false *a 4.469,0.458 4.781,0.615 0.313,0.156 10 false *b 2.104,0.302 2.417,0.5 0.313,0.198 10 false I3 5.583,0.635 5.896,0.833 0.313,0.198 10 false I76
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I3-2 (CANH) - I3-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
I3-2 (CANH) - I76-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I3-1 (CANL) - I76-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I3-2 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I3-1 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4 WHEEL DRIVE CONTROL ECU


Refer to Terminals of ECU.

Click hereDrivetrain>JF2BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4 wheel drive control ECU connectors.

C460151C01
1.615,0.271 2.115,0.573 0.5,0.302 5.146,0.344 5.646,0.646 0.5,0.302 0.188,0.083 0.5,0.281 0.313,0.198 10 false *a 5.271,0.417 5.583,0.615 0.313,0.198 10 false B10 1.771,0.333 2.083,0.531 0.313,0.198 10 false B9
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B9-6 (CANH) - B9-7 (CANH) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B9-6 (CANH) - B10-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B9-7 (CANH) - B10-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B9-6 (CANH) - B9-8 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B9-7 (CANH) - B9-8 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TCM (w/ Automatic Transmission System (for AJA0F))


Refer to Terminals of ECU.

for V35A-FTS: Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for V35A-FTS)>TERMINALS OF ECU

for F33A-FTV: Click hereDrivetrain>AJA0F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for F33A-FTV)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458408C05
1.5,0.417 1.917,0.667 0.417,0.25 1.583,0.469 2.042,0.667 0.458,0.198 10 false C36 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
C36-20 (CANH) - C36-21 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C36-20 (CANH) - C36-2 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C36-21 (CANL) - C36-2 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C36-20 (CANH) - C36-41 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C36-21 (CANL) - C36-41 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 1GR-FE)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C457119C02
1.5,0.167 1.99,0.469 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.677,0.26 1.99,0.458 0.313,0.198 10 false B2
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B2-11 (CANH) - B2-19 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B2-11 (CANH) - B2-52 (EC) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B2-19 (CANL) - B2-52 (EC) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B2-11 (CANH) - B2-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B2-19 (CANL) - B2-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B2-10 (CANP) - B2-18 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B2-10 (CANP) - B2-52 (EC) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B2-18 (CANN) - B2-52 (EC) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B2-10 (CANP) - B2-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B2-18 (CANN) - B2-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for V35A-FTS)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>V35A-FTS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C470354C02
1.5,0.25 2,0.583 0.5,0.333 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.656,0.333 1.969,0.531 0.313,0.198 10 false B1
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B1-18 (CANH) - B1-17 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B1-18 (CANH) - B1-9 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B1-17 (CANL) - B1-9 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B1-18 (CANH) - B1-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B1-17 (CANL) - B1-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B1-16 (CACH) - B1-15 (CACL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B1-16 (CACH) - B1-9 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B1-15 (CACL) - B1-9 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B1-16 (CACH) - B1-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B1-15 (CACL) - B1-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for F33A-FTV)


Refer to Terminals of ECU.

w/ DPF: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>TERMINALS OF ECM

w/o DPF: Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C470354C01
1.5,0.25 2,0.583 0.5,0.333 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.635,0.313 1.948,0.51 0.313,0.198 10 false B70
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B70-7 (CANH) - B70-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B70-7 (CANH) - B70-10 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B70-8 (CANL) - B70-10 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B70-7 (CANH) - B70-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B70-8 (CANL) - B70-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B70-17 (CACH) - B70-18 (CACL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B70-17 (CACH) - B70-10 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B70-18 (CACL) - B70-10 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B70-17 (CACH) - B70-1 (BATT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B70-18 (CACL) - B70-1 (BATT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ABSORBER CONTROL ECU (w/ Adaptive Variable Suspension System)


Refer to Terminals of ECU.

Click hereSuspension>SUSPENSION CONTROL>ADAPTIVE VARIABLE SUSPENSION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the absorber control ECU connector.

C471950C01
2,0.25 2.583,0.5 0.583,0.25 5.406,0.458 5.99,0.708 0.583,0.25 1.01,0.365 1.323,0.521 0.313,0.156 10 false *a 4.656,0.458 4.969,0.615 0.313,0.156 10 false *b 2.125,0.281 2.583,0.479 0.458,0.198 10 false Q11 5.594,0.5 6.052,0.698 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Absorber Control ECU)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 6 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
Q11-8 (CANH) - Q11-7 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q11-8 (CANH) - Q11-4 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q11-7 (CANL) - Q11-4 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q11-8 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q11-7 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
Q11-19 (CA2H) - Q11-18 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q11-19 (CA2H) - Q11-4 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q11-18 (CA2L) - Q11-4 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q11-19 (CA2H) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q11-18 (CA2L) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STABILIZER CONTROL ECU (w/ Electronic-Kinetic Dynamic Suspension System)


Refer to Terminals of ECU.

Click hereSuspension>SUSPENSION CONTROL>ELECTRONIC-KINETIC DYNAMIC SUSPENSION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453226C10
0.198,1.01 0.688,1.313 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.323,1.083 0.781,1.281 0.458,0.198 10 false Q14
*a Front view of wire harness connector
(to Stabilizer Control ECU)


Disconnect the stabilizer control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
Q14-8 (CANH) - Q14-7 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Q14-8 (CANH) - Q14-4 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q14-7 (CANL) - Q14-4 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Q14-8 (CANH) - Q14-1 (IGB) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Q14-7 (CANL) - Q14-1 (IGB) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO RECEIVER ASSEMBLY (w/ Audio and Visual System for Radio and Display Type, for 12.3 Inch Display)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, for 12.3 Inch Display)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio receiver assembly connectors.

C460152C01
1.552,0.281 2,0.583 0.448,0.302 5.146,0.271 5.594,0.573 0.448,0.302 1.708,0.333 2.167,0.531 0.458,0.198 10 false I12 5.292,0.333 5.75,0.531 0.458,0.198 10 false I10 0.167,0.135 0.583,0.5 0.417,0.365 10 false *a
*a Front view of wire harness connector
(to Radio Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I12-13 (CANH) - I12-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I12-13 (CANH) - I10-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I12-14 (CANL) - I10-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I12-13 (CANH) - I10-4 (+B1) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I12-14 (CANL) - I10-4 (+B1) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER (w/ Audio and Visual System for Radio and Display Type, except 12.3 Inch Display)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type, except 12.3 Inch Display)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connectors.

C460152C03
4.969,0.333 5.5,0.667 0.531,0.333 1.583,0.333 2.115,0.667 0.531,0.333 1.76,0.396 2.219,0.594 0.458,0.198 10 false I13 5.167,0.417 5.625,0.615 0.458,0.198 10 false I11 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I13-13 (CANH) - I13-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I13-13 (CANH) - I11-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I13-14 (CANL) - I11-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I13-13 (CANH) - I11-4 (+B1) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I13-14 (CANL) - I11-4 (+B1) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




INTEGRATION CONTROL SUB-ASSEMBLY (for Radio and Display Type, for 12.3 Inch Display)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>TOYOTA MULTI OPERATION TOUCH SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453222C04
1.458,0.177 1.948,0.479 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.604,0.26 2.063,0.458 0.458,0.198 10 false I22
*a Front view of wire harness connector
(to Integration Control Sub-assembly)


Disconnect the integration control sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I22-32 (CANP) - I22-31 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I22-32 (CANP) - I22-20 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I22-31 (CANN) - I22-20 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I22-32 (CANP) - I22-1 (B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I22-31 (CANN) - I22-1 (B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connectors.

C406372C25
1.688,0.281 2.156,0.573 0.469,0.292 4.99,0.313 5.458,0.604 0.469,0.292 0.667,0.427 0.979,0.625 0.313,0.198 10 false *a 3.875,0.438 4.188,0.635 0.313,0.198 10 false *b 1.802,0.344 2.26,0.542 0.458,0.198 10 false T10 5.135,0.365 5.594,0.563 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
T10-2 (CA1P) - T10-7 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
T10-2 (CA1P) - T10-10 (BLGD) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T10-7 (CA1N) - T10-10 (BLGD) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T10-2 (CA1P) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T10-7 (CA1N) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the multiplex network door ECU connectors.

C460153C01
1.479,0.25 2,0.573 0.521,0.323 5.083,0.25 5.604,0.573 0.521,0.323 1.688,0.333 2,0.531 0.313,0.198 10 false T1 5.281,0.333 5.594,0.531 0.313,0.198 10 false T3 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
T1-10 (CANP) - T1-20 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
T1-10 (CANP) - T3-4 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T1-20 (CANN) - T3-4 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T1-10 (CANP) - T1-7 (ECUB) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T1-20 (CANN) - T1-7 (ECUB) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Reverse Shift-linked Mirror)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C457121C06
1.5,0.083 2,0.5 0.5,0.417 1.667,0.219 1.979,0.417 0.313,0.198 10 false M1 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Disconnect the outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M1-9 (CANP) - M1-8 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M1-9 (CANP) - M1-7 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M1-8 (CANN) - M1-7 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M1-9 (CANP) - M1-6 (CPUB) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M1-8 (CANN) - M1-6 (CPUB) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Reverse Shift-linked Mirror)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C457121C05
1.51,0.271 2,0.573 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.646,0.333 1.958,0.531 0.313,0.198 10 false N1
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


Disconnect the outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N1-9 (CANP) - N1-8 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
N1-9 (CANP) - N1-7 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N1-8 (CANN) - N1-7 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
N1-9 (CANP) - N1-6 (CPUB) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N1-8 (CANN) - N1-6 (CPUB) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System for Type A)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL SYSTEM (for Type A)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C457122C03
1.51,0.271 2,0.573 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.615,0.365 2.073,0.563 0.458,0.198 10 false S20
*a Front view of wire harness connector
(to Stereo Component Equalizer Assembly)


Disconnect the stereo component equalizer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
S20-1 (CANH) - S20-15 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S20-1 (CANH) - S20-28 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S20-15 (CANL) - S20-28 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S20-1 (CANH) - S20-14 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S20-15 (CANL) - S20-14 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System for Type B)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ACTIVE NOISE CONTROL SYSTEM (for Type B)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C458561C03
1.51,0.271 2,0.573 0.49,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.615,0.365 2.073,0.563 0.458,0.198 10 false S25
*a Front view of wire harness connector
(to Stereo Component Equalizer Assembly)


Disconnect the stereo component equalizer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
S25-1 (CANH) - S25-16 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S25-1 (CANH) - S25-30 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S25-16 (CANL) - S25-30 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S25-1 (CANH) - S25-15 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S25-16 (CANL) - S25-15 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR (w/ Pre-collision System)


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connectors.

C406375C17
4.99,0.208 5.458,0.49 0.469,0.281 1.74,0.115 2.229,0.385 0.49,0.271 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *b 1.833,0.177 2.292,0.375 0.458,0.198 10 false A10 5.125,0.26 5.583,0.458 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A10-3 (CA2H) - A10-2 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A10-3 (CA2H) - A10-1 (SGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A10-2 (CA2L) - A10-1 (SGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A10-3 (CA2H) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A10-2 (CA2L) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the rear television camera assembly connectors.

C458822C01
5.021,0.406 5.49,0.688 0.469,0.281 1.677,0.24 2.167,0.51 0.49,0.271 0.688,0.219 1,0.417 0.313,0.198 10 false *a 3.917,0.219 4.229,0.417 0.313,0.198 10 false *b 1.792,0.302 2.25,0.5 0.458,0.198 10 false g18 5.146,0.469 5.604,0.667 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
g18-1 (CANH) - g18-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
g18-1 (CANH) - I76- 4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
g18-2 (CANL) - I76- 4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
g18-1 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
g18-2 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the rear television camera assembly connectors.

C409699C05
5.042,0.542 5.51,0.823 0.469,0.281 1.865,0.344 2.354,0.615 0.49,0.271 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *b 2.021,0.385 2.333,0.583 0.313,0.198 10 false g9 5.188,0.594 5.646,0.792 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
g9-4 (CANH) - g9-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
g9-4 (CANH) - I76-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
g9-1 (CANL) - I76-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
g9-4 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
g9-1 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Pre-collision System)


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>PRE-COLLISION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the forward recognition camera connectors.

C406374C23
5.042,0.458 5.51,0.74 0.469,0.281 1.771,0.344 2.26,0.615 0.49,0.271 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *b 1.906,0.417 2.365,0.615 0.458,0.198 10 false d20 5.188,0.521 5.646,0.719 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
d20-5 (CA1P) - d20-11 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
d20-5 (CA1P) - d20-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d20-11 (CA1N) - d20-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d20-5 (CA1P) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d20-11 (CA1N) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C453240C07
1.479,0.167 1.979,0.417 0.5,0.25 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.625,0.219 2.146,0.552 0.521,0.333 10 false T11
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
T11-9 (CANH) - T11-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
T11-9 (CANH) - T11-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T11-10 (CANL) - T11-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
T11-9 (CANH) - T11-7 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
T11-10 (CANL) - T11-7 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the position control ECU assembly connector.

C470483C01
1.667,0.167 2.083,0.417 0.417,0.25 5.063,0.208 5.479,0.458 0.417,0.25 1.667,0.5 2.083,0.75 0.417,0.25 5.073,0.531 5.49,0.781 0.417,0.25 2.188,0.208 2.5,0.365 0.313,0.156 10 false *A 2.198,0.563 2.51,0.719 0.313,0.156 10 false *B 0.094,0.083 0.51,0.385 0.417,0.302 12 false *a 1.771,0.219 2.25,0.427 0.479,0.208 10 false i19 1.75,0.552 2.208,0.75 0.458,0.198 10 false h24 5.188,0.25 5.667,0.458 0.479,0.208 10 false i17 5.167,0.583 5.625,0.781 0.458,0.198 10 false h22 5.563,0.25 5.875,0.406 0.313,0.156 10 false *A 5.583,0.583 5.896,0.74 0.313,0.156 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Position Control ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
i19-13 (CANP) - i19-14 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
i19-13 (CANP) - i17-2 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
i19-14 (CANN) - i17-2 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
i19-13 (CANP) - i19-15 (SYSB) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
i19-14 (CANN) - i19-15 (SYSB) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
h24-13 (CANP) - h24-14 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
h24-13 (CANP) - h22-2 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
h24-14 (CANN) - h22-2 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
h24-13 (CANP) - h24-15 (SYSB) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
h24-14 (CANN) - h24-15 (SYSB) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C380494C39
1.469,0.448 1.969,0.75 0.5,0.302 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.635,0.521 2.094,0.719 0.458,0.198 10 false I17
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Disconnect the meter mirror sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I17-12 (MPX1) - I17-13 (MPX2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I17-12 (MPX1) - I17-4 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-13 (MPX2) - I17-4 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I17-12 (MPX1) - I17-2 (B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I17-13 (MPX2) - I17-2 (B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Multi-terrain Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C380494C40
1.458,0.521 1.927,0.792 0.469,0.271 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.615,0.583 2.073,0.781 0.458,0.198 10 false I60
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I60-11 (CANH) - I60-12 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I60-11 (CANH) - I60-4 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I60-12 (CANL) - I60-4 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I60-11 (CANH) - I60-1 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I60-12 (CANL) - I60-1 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Headlight ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406391C40
1.469,0.083 1.938,0.365 0.469,0.281 1.552,2.385 2.021,2.667 0.469,0.281 1.469,0.417 1.938,0.698 0.469,0.281 0.167,0.073 0.479,0.271 0.313,0.198 10 false *a 0.177,2.396 0.49,2.594 0.313,0.198 10 false *b 1.615,0.146 1.927,0.344 0.313,0.198 10 false B4 1.698,2.458 2.156,2.656 0.458,0.198 10 false I76 2.01,0.125 2.323,0.323 0.313,0.198 10 false *A 2.031,0.438 2.344,0.635 0.313,0.198 10 false *B 1.604,0.469 1.917,0.667 0.313,0.198 10 false B88
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
*b Front view of DLC3


Disconnect the headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B4-24 (CANH) - B4-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B4-24 (CANH) - B4-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B4-23 (CANL) - B4-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B4-24 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B4-23 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B88-24 (CANH) - B88-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B88-24 (CANH) - B88-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B88-23 (CANL) - B88-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B88-24 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B88-23 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Headlight ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (w/ Headlight ECU)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C406391C41
1.448,0.073 1.917,0.354 0.469,0.281 1.552,2.385 2.021,2.667 0.469,0.281 1.448,0.406 1.917,0.688 0.469,0.281 0.167,0.073 0.479,0.271 0.313,0.198 10 false *a 0.177,2.396 0.49,2.594 0.313,0.198 10 false *b 1.583,0.156 1.896,0.354 0.313,0.198 10 false B7 1.708,2.448 2.167,2.646 0.458,0.198 10 false I76 1.573,0.49 1.885,0.688 0.313,0.198 10 false B89 2,0.125 2.313,0.323 0.313,0.198 10 false *A 2.031,0.479 2.344,0.677 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)
*b Front view of DLC3


Disconnect the headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B7-24 (CANH) - B7-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B7-24 (CANH) - B7-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B7-23 (CANL) - B7-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B7-24 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B7-23 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B89-24 (CANH) - B89-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B89-24 (CANH) - B89-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B89-23 (CANL) - B89-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B89-24 (CANH) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B89-23 (CANL) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C343810C25
1.375,0.594 1.906,0.875 0.531,0.281 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.51,0.646 1.969,0.844 0.458,0.198 10 false B20
*a Front view of wire harness connector
(to Brake Actuator Assembly (No.2 Skid Control ECU))


Disconnect the brake actuator assembly (No. 2 skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B20-27 (CANH) - B20-43 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B20-27 (CANH) - B20-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B20-43 (CANL) - B20-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B20-27 (CANH) - B20-14 (+BS) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B20-43 (CANL) - B20-14 (+BS) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B20-16 (CA2H) - B20-17 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
B20-16 (CA2H) - B20-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B20-17 (CA2L) - B20-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B20-16 (CA2H) - B20-14 (+BS) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B20-17 (CA2L) - B20-14 (+BS) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C303147C20
1.427,0.542 1.969,0.823 0.542,0.281 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.604,0.604 2.063,0.802 0.458,0.198 10 false B19
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU))


Disconnect the brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B19-38 (CA1H) - B19-39 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B19-38 (CA1H) - B19-28 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B19-39 (CA1L) - B19-28 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B19-38 (CA1H) - B19-14 (+BI1) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B19-39 (CA1L) - B19-14 (+BI1) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B19-35 (CA2H) - B19-36 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
B19-35 (CA2H) - B19-28 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B19-36 (CA2L) - B19-28 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
B19-35 (CA2H) - B19-14 (+BI1) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
B19-36 (CA2L) - B19-14 (+BI1) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System)


Refer to Terminals of ECU.

for ERA-GLONASS: Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>TERMINALS OF ECU

for eCall: Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU

for Toyota Connected Services: Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the telephone transceiver assembly connector.

C457124C02
3.167,0.083 3.667,0.417 0.5,0.333 3.333,0.167 4.083,0.667 0.75,0.5 10 false I55 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I55-25 (CANP) - I55-26 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I55-25 (CANP) - I55-20 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I55-26 (CANN) - I55-20 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I55-25 (CANP) - I55-1 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I55-26 (CANN) - I55-1 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



POWER STEERING ECU WITH MOTOR ASSEMBLY (w/ Lane Tracing Assist System)


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ Variable Flow Control Solenoid Valve)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C460323C01
1.5,0.167 1.833,0.417 0.333,0.25 1.573,2.667 1.906,2.917 0.333,0.25 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.573,0.219 2.031,0.417 0.458,0.198 10 false I71 1.635,2.719 2.094,2.917 0.458,0.198 10 false I70
*a Front view of wire harness connector
(to Power Steering ECU with Motor Assembly)


Disconnect the power steering ECU with motor assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I71-7 (CANH) - I71-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I71-7 (CANH) - I70-2 (PGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I71-8 (CANL) - I70-20 (PGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I71-7 (CANH) - I71-1 (IG) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I71-8 (CANL) - I71-1 (IG) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ENGINE STOP AND START ECU (w/ Stop and Start System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the engine stop and start ECU connectors.

C470488C01
5.448,0.417 5.917,0.771 0.469,0.354 1.198,0.417 1.667,0.771 0.469,0.354 3.198,0.417 3.667,0.771 0.469,0.354 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.333,0.49 1.792,0.688 0.458,0.198 10 false I57 3.302,0.521 3.76,0.719 0.458,0.198 10 false B37 5.552,0.51 6.01,0.708 0.458,0.198 10 false B38
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I57-13 (CANH) - I57-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I57-13 (CANH) - B37-8 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I57-14 (CANL) - B37-8 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I57-13 (CANH) - B38-1 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I57-14 (CANL) - B38-1 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
I57-15 (LC1H) - I57-16 (LC1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I57-15 (LC1H) - B37-8 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I57-16 (LC1L) - B37-8 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I57-15 (LC1H) - B38-1 (+B) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I57-16 (LC1L) - B38-1 (+B) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



OPTION CONNECTOR (BUS BUFFER ECU)


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the option connector (bus buffer ECU) connectors.

C460164C01
5.375,0.479 5.917,0.833 0.542,0.354 1.917,0.396 2.458,0.75 0.542,0.354 1.521,0.469 1.833,0.667 0.313,0.198 10 false *a 4.583,0.5 4.896,0.698 0.313,0.198 10 false *b 2.083,0.5 2.542,0.698 0.458,0.198 10 false I96 5.521,0.552 5.979,0.75 0.458,0.198 10 false I76
*a Front view of wire harness connector
(to Option Connector (Bus Buffer ECU))
*B DLC3



c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I96-2 (CAN+) - I96-1 (CAN-) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I96-2 (CAN+) - I76-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I96-1 (CAN-) - I76-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I96-2 (CAN+) - I76-16 (BAT) HIGH-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I96-1 (CAN-) - I76-16 (BAT) LOW-level CAN bus line - battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher