Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2021.08
RM37H0E _57 Power Source / Network _095302 NETWORKING _0455452 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 GLOBAL CAN JUNCTION CONNECTOR


C452984C01
2.01,0.76 2.438,1.01 0.427,0.25 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 2.094,0.813 2.406,1.01 0.313,0.198 10 false A77
*a Front view of wire harness connector
(to No. 1 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
Brake booster with master cylinder assembly (No. 1 skid control ECU) A77-1 (CANH) GR
A77-5 (CANL) W
Brake actuator assembly (No. 2 skid control ECU) A77-2 (CANH) LG
A77-6 (CANL) G
No. 3 global CAN junction connector A77-3 (CANH) V
A77-7 (CANL) W
Rack and pinion power steering gear assembly A77-4 (CANH) B
A77-8 (CANL) W


NO. 2 GLOBAL CAN JUNCTION CONNECTOR


C452985C01
3.375,0.375 3.771,0.625 0.396,0.25 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 3.417,0.427 3.979,0.625 0.563,0.198 10 false D162
*a Front view of wire harness connector
(to No. 2 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Navigation System

*2: w/o Navigation System

*3: w/ Telematics System

*4: w/ ASC System

*5: w/ Door Closer System

·

Radio receiver assembly*1

·

Radio and display receiver assembly*2


D162-7 (CANH) B
D162-1 (CANL) W
Central gateway ECU (network gateway ECU) D162-8 (CANH) L
D162-2 (CANL) W
No. 14 global CAN junction connector D162-9 (CANH) P
D162-3 (CANL) W
Telematics transceiver *3 D162-10 (CANH) G
D162-4 (CANL) W
Stereo component equalizer assembly *4 D162-11 (CANH) SB
D162-5 (CANL) W
Rear multiplex network door ECU LH*5 D162-12 (CANH) V
D162-6 (CANL) W


NO. 3 GLOBAL CAN JUNCTION CONNECTOR


C452984C02
2.01,0.76 2.438,1.01 0.427,0.25 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 2.094,0.813 2.542,1.052 0.448,0.24 10 false D163
*a Front view of wire harness connector
(to No. 3 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
No. 1 global CAN junction connector D163-1 (CANH) V
D163-5 (CANL) W
No. 4 global CAN junction connector D163-2 (CANH) P
D163-6 (CANL) W
Airbag ECU assembly (for RHD) D163-4 (CANH) Y
D163-8 (CANL) W
Steering sensor (for LHD) D163-3 (CANH) G
D163-7 (CANL) W


NO. 4 GLOBAL CAN JUNCTION CONNECTOR


C452984C07
1.885,0.969 2.313,1.219 0.427,0.25 1.885,0.469 2.313,0.719 0.427,0.25 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 1.958,1.01 2.406,1.25 0.448,0.24 10 false D165 1.938,0.5 2.385,0.74 0.448,0.24 10 false D164 2.365,0.49 2.813,0.729 0.448,0.24 10 false *A 2.375,1.01 2.823,1.25 0.448,0.24 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to No. 4 Global CAN Junction Connector)
- -


for LHD
Connected to Terminal No. (Symbol) Wiring Color
Central gateway ECU (network gateway ECU) D164-1 (CANH) V
D164-5 (CANL) W
Central gateway ECU (network gateway ECU) D164-2 (CANH) Y
D164-6 (CANL) W
No. 3 global CAN junction connector D164-3 (CANH) P
D164-7 (CANL) W
Airbag ECU assembly D164-4 (CANH) Y
D164-8 (CANL) W

for RHD
Connected to Terminal No. (Symbol) Wiring Color
Central gateway ECU (network gateway ECU) D165-1 (CANH) V
D165-5 (CANL) W
Central gateway ECU (network gateway ECU) D165-2 (CANH) Y
D165-6 (CANL) W
No. 3 global CAN junction connector D165-3 (CANH) P
D165-7 (CANL) W
Steering sensor D165-4 (CANH) Y
D165-8 (CANL) W


NO. 5 GLOBAL CAN JUNCTION CONNECTOR


C452913C02
1.604,1.271 2.083,1.531 0.479,0.26 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.698,1.333 2.083,1.51 0.385,0.177 10 false D166
*a Front view of wire harness connector
(to No. 5 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: for LHD

*2: for RHD

·

Meter mirror sub-assembly (for LHD with Headup Display System)

·

Certification ECU (smart key ECU assembly) (for RHD)


D166-12 (CANH) BE*1
G*2
D166-2 (CANL) W
·

Certification ECU (smart key ECU assembly) (for LHD)

·

Meter mirror sub-assembly (for RHD with Headup Display System)


D166-13 (CANH) G*1
BE*2
D166-3 (CANL) W
·

Air conditioning amplifier assembly (for LHD)

·

Multiplex tilt and telescopic ECU (for RHD)


D166-14 (CANH) L*1
V*2
D166-4 (CANL) W
Main body ECU (multiplex network body ECU) D166-15 (CANH) B
D166-5 (CANL) W
·

Multiplex tilt and telescopic ECU (for LHD)

·

Air conditioning amplifier assembly (for RHD)


D166-16 (CANH) V*1
L*2
D166-6 (CANL) W
No. 9 global CAN junction connector D166-17 (CANH) BR
D166-7 (CANL) W
Combination meter assembly (for RHD) D166-18 (CANH) Y
D166-8 (CANL) W
Integration control sub-assembly (w/ Navigation System) D166-19 (CANH) R
D166-9 (CANL) W
Combination meter assembly (for LHD) D166-20 (CANH) Y
D166-10 (CANL) W


NO. 6 GLOBAL CAN JUNCTION CONNECTOR


C452913C03
1.406,1.188 1.865,1.438 0.458,0.25 1.479,1.24 2.094,1.438 0.615,0.198 10 false D170 0.073,0.063 0.688,0.26 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
No. 13 global CAN junction connector D170-11 (CANH) B
D170-1 (CANL) W
Millimeter wave radar sensor assembly D170-12 (CANH) V
D170-2 (CANL) W
Central gateway ECU (network gateway ECU) D170-16 (CANH) LG
D170-6 (CANL) W
Forward recognition camera D170-17 (CANH) V
D170-7 (CANL) W


NO. 7 GLOBAL CAN JUNCTION CONNECTOR


C452913C13
1.125,1.375 1.604,1.635 0.479,0.26 1.125,0.99 1.604,1.25 0.479,0.26 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.208,1.417 1.594,1.594 0.385,0.177 10 false D173 1.698,1.031 2.083,1.208 0.385,0.177 10 false *A 1.208,1.031 1.594,1.208 0.385,0.177 10 false D172 1.688,1.417 2.073,1.594 0.385,0.177 10 false *B
*A for LHD *B for RHD
*a Front view of wire harness connector
(to No. 7 Global CAN Junction Connector)
- -


for LHD
Connected to Terminal No. (Symbol) Wiring Color
Central gateway ECU (network gateway ECU) D172-11 (CANH) R
D172-1 (CANL) W
EV control ECU D172-12 (CANH) L
D172-2 (CANL) W
Shift control ECU D172-13 (CANH) Y
D172-3 (CANL) W
No. 10 global CAN junction connector D172-15 (CANH) BR
D172-5 (CANL) W
Vehicle approaching speaker controller D172-16 (CANH) B
D172-6 (CANL) W
FC control ECU D172-17 (CANH) GR
D172-7 (CANL) W
FC converter assembly D172-18 (CANH) G
D172-8 (CANL) W

for RHD
Connected to Terminal No. (Symbol) Wiring Color
Central gateway ECU (network gateway ECU) D173-11 (CANH) R
D173-1 (CANL) W
EV control ECU D173-12 (CANH) L
D173-2 (CANL) W
Shift control ECU D173-13 (CANH) Y
D173-3 (CANL) W
No. 10 global CAN junction connector D173-15 (CANH) BR
D173-5 (CANL) W
Vehicle approaching speaker controller D173-16 (CANH) BR
D173-6 (CANL) W
FC control ECU D172-17 (CANH) GR
D172-7 (CANL) W
FC converter assembly D173-18 (CANH) G
D173-8 (CANL) W


NO. 8 GLOBAL CAN JUNCTION CONNECTOR


C452985C02
1.469,1.25 1.875,1.479 0.406,0.229 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.531,1.302 2,1.49 0.469,0.188 10 false G120
*a Front view of wire harness connector
(to No. 8 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
Front multiplex network door ECU RH (w/ Reverse Shift-linked Mirror) G120-1 (CANH) GR
G120-7 (CANL) W
Position control ECU assembly (for RHD with Seat Position Memory System) G120-2 (CANH) SB
G120-8 (CANL) W
No. 9 global CAN junction connector G120-4 (CANH) R
G120-10 (CANL) W
No. 1 CAN junction terminal G120-5 (CANH) L
G120-11 (CANL) W
Headlight ECU sub-assembly RH G120-6 (CANH) B
G120-12 (CANL) W


NO. 9 GLOBAL CAN JUNCTION CONNECTOR


C435672C57
1.448,1.26 1.854,1.49 0.406,0.229 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.521,1.302 1.885,1.458 0.365,0.156 10 false G121
*a Front view of wire harness connector
(to No. 9 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
No. 5 global CAN junction connector G121-1 (CANH) BR
G121-7 (CANL) W
Front multiplex network door ECU LH (w/ Reverse Shift-linked Mirror) G121-2 (CANH) GR
G121-8 (CANL) W
No. 8 global CAN junction connector G121-3 (CANH) R
G121-9 (CANL) W
Position control ECU assembly (w/ Seat Position Memory System) G120-4 (CANH) Y
G120-10 (CANL) W
Headlight ECU sub-assembly LH G121-5 (CANH) V
G121-11 (CANL) W
Central gateway ECU (network gateway ECU) G121-6 (CANH) BR
G121-12 CANL) W


NO. 10 GLOBAL CAN JUNCTION CONNECTOR


C452984C04
2.01,0.76 2.438,1.01 0.427,0.25 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 2.094,0.813 2.573,1.042 0.479,0.229 10 false G123
*a Front view of wire harness connector
(to No. 10 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
No. 7 global CAN junction connector G123-1 (CANH) BR
G123-5 (CANL) W
Battery ECU assembly G123-3 (CANH) B
G123-7 (CANL) W
Hydrogen fuel control ECU assembly G123-4 (CANH) V
G123-8 (CANL) W


NO. 1 CAN JUNCTION CONNECTOR


C387412C62
1.438,1.26 1.844,1.49 0.406,0.229 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.49,1.302 1.854,1.458 0.365,0.156 10 false A78
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
EV control ECU A78-2 (CANH) R
A78-13 (CANL) W
Brake actuator assembly (No. 2 skid control ECU) A78-5 (CANH) G
A78-16 (CANL) W
Brake booster with master cylinder assembly (No. 1 skid control ECU) A78-6 (CANH) L
A78-17 (CANL) W


NO. 12 GLOBAL CAN JUNCTION CONNECTOR


C452987C01
1.958,1.417 2.396,1.656 0.438,0.24 0.052,0.094 0.365,0.292 0.313,0.198 10 false *a 2.01,1.469 2.417,1.677 0.406,0.208 10 false G125
*a Front view of wire harness connector
(to No. 12 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*: w/ Occupant Classification System

No. 2 CAN junction terminal G125-8 (CANH) B
G125-19 (CANL) W
Central gateway ECU (network gateway ECU) G125-9 (CANH) LG
G125-20 (CANL) W
Tire pressure warning ECU and receiver G125-10 (CANH) Y
G125-21 (CANL) W
Occupant detection ECU* G125-11 (CANH) BE
G125-22 (CANL) W


NO. 13 GLOBAL CAN JUNCTION CONNECTOR


C452913C05
1.688,1.354 2.125,1.594 0.438,0.24 0.052,0.094 0.365,0.292 0.313,0.198 10 false *a 1.781,1.417 2.188,1.625 0.406,0.208 10 false G128
*a Front view of wire harness connector
(to No. 13 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color
No. 6 global CAN junction connector G128-1 (CANH) B
G128-11 (CANL) W
No. 3 CAN junction terminal G128-2 (CANH) V
G128-12 (CANL) W
Parking assist ECU (w/ Panoramic View Monitor System) G128-3 (CANH) L
G128-13 (CANL) W
Rear television camera assembly G128-5 (CANH) P
G128-15 (CANL) W
Blind spot monitor sensor RH (B) (w/ Blind Spot Monitor System) G128-6 (CANH) LG
G128-16 (CANL) W
Clearance warning ECU assembly (w/ TOYOTA Parking Assist-sensor System) G128-8 (CANH) BE
G128-18 (CANL) W


NO. 14 GLOBAL CAN JUNCTION CONNECTOR


C452984C11
2.01,0.76 2.438,1.01 0.427,0.25 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 2.052,0.802 2.552,1.031 0.5,0.229 10 false G160
*a Front view of wire harness connector
(to No. 14 Global CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: w/ Luggage Compartment Door Closer System

*2: w/ Double Locking System

No. 2 global CAN junction connector G160-1 (CANH) P
G160-5 (CANL) W
Multiplex network door ECU*1 G160-2 (CANH) R
G160-6 (CANL) W
Rear multiplex network door ECU RH*2 G160-3 (CANH) GR
G160-7 (CANL) W
Central gateway ECU (network gateway ECU) G160-4 (CANH) B
G160-8 (CANL) W


NO. 3 CAN JUNCTION CONNECTOR


C387412C63
1.438,1.26 1.844,1.49 0.406,0.229 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.49,1.302 1.854,1.458 0.365,0.156 10 false D168
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
- -


Connected to Terminal No. (Symbol) Wiring Color

*1: for LHD

*2: for RHD

Central gateway ECU (network gateway ECU) D168-12 (CANH) B
D168-1 (CANL) W
·

Rack and pinion power steering gear assembly (for LHD)

·

Brake actuator assembly (No. 2 skid control ECU) (for RHD)


D168-13 (CANH) G*1
L*2
D168-2 (CANL) W
·

Brake actuator assembly (No. 2 skid control ECU) (for LHD)

·

Airbag ECU assembly (for RHD)


D168-14 (CANH) L*1
G*2
D168-3 (CANL) W


NO. 1 CAN JUNCTION TERMINAL


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453185C01
1.469,0.229 2.01,0.521 0.542,0.292 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 1.573,0.292 2.031,0.521 0.458,0.229 10 false G122
*a Front view of wire harness connector
(No. 1 CAN Junction Terminal)


Disconnect the No. 1 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Connected to
G122-3 (CANH) L No. 8 global CAN junction connector
G122-2 (CANL) W




NO. 2 CAN JUNCTION TERMINAL


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453185C02
1.427,0.302 1.906,0.573 0.479,0.271 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.5,0.354 1.896,0.531 0.396,0.177 10 false G126
*a Front view of wire harness connector
(No. 2 CAN Junction Terminal)


Disconnect the No. 2 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Connected to
G126-3 (CANH) B No. 12 global CAN junction connector
G126-2 (CANL) W




NO. 3 CAN JUNCTION TERMINAL


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453185C03
1.427,0.302 1.906,0.573 0.479,0.271 0.104,0.115 0.417,0.271 0.313,0.156 10 false *a 1.5,0.354 1.896,0.531 0.396,0.177 10 false G129
*a Front view of wire harness connector
(No. 3 CAN Junction Terminal)


Disconnect the No. 3 CAN junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Connected to
G129-3 (CANH) B No. 13 global CAN junction connector
G129-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C391595C22
1.625,1.313 2.042,1.583 0.417,0.271 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.698,1.354 2.333,1.583 0.635,0.229 10 false D20
*a Front view of DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D20-6 (CANH) - D20-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D20-6 (CANH) - D20-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D20-14 (CANL) - D20-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D20-6 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D20-14 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C422307C10
3.49,0.135 3.906,0.385 0.417,0.25 0.188,0.198 0.5,0.396 0.313,0.198 10 false *a 3.542,0.167 4,0.365 0.458,0.198 10 false D119
*a Component without harness connected
(to Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.

C422308C21
0.625,0.792 1.125,1.042 0.5,0.25 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.708,0.833 1.146,1.052 0.438,0.219 10 false D119
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines (DLC3 - Central Gateway ECU [Network Gateway ECU])
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-16 (CA6H) - D119-17 (CA6L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
D119-16 (CA6H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-17 (CA6L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-16 (CA6H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-17 (CA6L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-28 (CA1H) - D119-27 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-28 (CA1H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-27 (CA1L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-28 (CA1H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-27 (CA1L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-26 (CA4H) - D119-25 (CA4L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D119-26 (CA4H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-25 (CA4L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-26 (CA4H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-25 (CA4L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-30 (CA3H) - D119-29 (CA3L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-14 (CAXH) - D119-15 (CAXL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-30 (CA3H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-29 (CA3L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-30 (CA3H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-29 (CA3L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Main and Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-24 (CA2H) - D119-23 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-10 (CAVH) - D119-11 (CAVL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-24 (CA2H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-23 (CA2L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-24 (CA2H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-23 (CA2L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-7 (CA5H) - D119-8 (CA5L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D119-7 (CA5H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-8 (CA5L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-7 (CA5H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-8 (CA5L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 6 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-31 (CA7H) - D119-32 (CA7L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-31 (CA7H) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-32 (CA7L) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-31 (CA7H) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-32 (CA7L) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Chassis Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D119-13 (CAWH) - D119-12 (CAWL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D119-13 (CAWH) - D119-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-12 (CAWL) - D119-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D119-13 (CAWH) - D119-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D119-12 (CAWL) - D119-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the forward recognition camera connector.

C406374C19
1.771,0.167 2.219,0.417 0.448,0.25 4.979,0.198 5.385,0.469 0.406,0.271 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *b 1.917,0.208 2.229,0.406 0.313,0.198 10 false H6 5.052,0.25 5.542,0.594 0.49,0.344 10 false D20
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H6-5 (CA1P) - H6-11 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H6-5 (CA1P) - H6-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H6-11 (CA1N) - H6-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H6-5 (CA1P) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H6-11 (CA1N) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.

C406375C14
4.99,0.208 5.458,0.49 0.469,0.281 1.781,0.156 2.208,0.427 0.427,0.271 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *b 5.063,0.281 5.5,0.51 0.438,0.229 10 false G114 1.865,0.198 2.188,0.396 0.323,0.198 10 false A86
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A86-3 (CA2H) - A86-2 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A86-3 (CA2H) - A86-1 (SGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A86-2 (CA2L) - A86-1 (SGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A86-3 (CA2H) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A86-2 (CA2L) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the parking assist ECU connector.


c.
C380494C33
1.417,0.75 1.917,1 0.5,0.25 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.542,0.802 1.854,1 0.313,0.198 10 false G13
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G13-11 (CANH) - G13-12 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G13-11 (CANH) - G13-4 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G13-12 (CANL) - G13-4 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G13-11 (CANH) - G13-1 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G13-12 (CANL) - G13-1 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the rear television camera assembly connector.

C409699C03
1.917,0.333 2.333,0.583 0.417,0.25 5.135,0.531 5.552,0.781 0.417,0.25 0.927,0.354 1.24,0.552 0.313,0.198 10 false *a 4.146,0.688 4.458,0.885 0.313,0.198 10 false *b 2.031,0.375 2.521,0.573 0.49,0.198 10 false K4 5.219,0.573 5.708,0.771 0.49,0.198 10 false D20
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
K4-4 (CANH) - K4-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K4-4 (CANH) - D20-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K4-1 (CANL) - D20-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K4-4 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K4-1 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/o Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the rear television camera assembly connector.

C454952C01
1.917,0.333 2.333,0.583 0.417,0.25 5.135,0.531 5.552,0.781 0.417,0.25 0.927,0.354 1.24,0.552 0.313,0.198 10 false *a 4.146,0.688 4.458,0.885 0.313,0.198 10 false *b 2.01,0.375 2.5,0.573 0.49,0.198 10 false K12 5.198,0.583 5.688,0.781 0.49,0.198 10 false D20
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
K12-1 (CANH) - K12-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
K12-1 (CANH) - D20-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K12-2 (CANL) - D20-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
K12-1 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
K12-2 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Intuitive TOYOTA Parking Assist-Sensor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.

C406371C20
1.688,0.188 2.104,0.458 0.417,0.271 5.073,0.177 5.49,0.448 0.417,0.271 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.917,0.115 4.229,0.313 0.313,0.198 10 false *b 1.771,0.25 2.156,0.521 0.385,0.271 10 false G20 5.156,0.24 5.813,0.469 0.656,0.229 10 false D20
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G20-17 (R1) - G20-18 (R2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G20-17 (R1) - G20-31 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-18 (R2) - G20-31 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G20-17 (R1) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G20-18 (R2) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR RH (B) (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the blind spot monitor sensor RH (B) connector.

C406372C22
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *b 1.781,0.198 2.104,0.396 0.323,0.198 10 false G56 5.052,0.271 5.615,0.49 0.563,0.219 10 false D20
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (B))
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G56-2 (CA1P) - G56-7 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G56-2 (CA1P) - G56-10 (BLGD) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G56-7 (CA1N) - G56-10 (BLGD) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G56-2 (CA1P) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G56-7 (CA1N) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BATTERY ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the battery ECU assembly connector.


c.
C453211C01
1.469,0.146 1.958,0.406 0.49,0.26 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.552,0.188 1.917,0.375 0.365,0.188 10 false G156
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G156-2 (CA2H) - G156-11 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G156-2 (CA2H) - G156-25 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G156-11 (CA2L) - G156-25 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G156-2 (CA2H) - G156-1 (AM) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G156-11 (CA2L) - G156-1 (AM) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




EV CONTROL ECU


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453217C01
0.344,0.979 0.771,1.25 0.427,0.271 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 0.438,1.042 0.74,1.208 0.302,0.167 10 false D15
*a Front view of wire harness connector
(to EV Control ECU)


Disconnect the EV control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D15-17 (CA1H) - D15-18 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D15-17 (CA1H) - D15-15 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D15-18 (CA1L) - D15-15 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D15-17 (CA1H) - D15-13 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D15-18 (CA1L) - D15-13 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Powertrain Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D15-14 (CA3P) - D15-15 (CA3N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D15-14 (CA3P) - D15-15 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D15-15 (CA3N) - D15-15 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D15-14 (CA3P) - D15-13 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D15-15 (CA3N) - D15-13 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FC CONVERTER ASSEMBLY


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453215C01
1.5,0.083 1.927,0.313 0.427,0.229 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.604,0.125 1.906,0.292 0.302,0.167 10 false B19
*a Front view of wire harness connector
(to FC Converter Assembly)


Disconnect the FC converter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B19-22 (CA1H) - B19-21 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
B19-22 (CA1H) - B19-9 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B19-21 (CA1L) - B19-9 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B19-22 (CA1H) - B19-36 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B19-21 (CA1L) - B19-36 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




VEHICLE APPROACHING SPEAKER CONTROLLER


Refer to Terminals of ECU.

Click hereVehicle Exterior>ACOUSTIC VEHICLE ALERTING SYSTEM>ACOUSTIC VEHICLE ALERTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the vehicle approaching speaker controller connector.


c.

Measure the resistance according to the value(s) in the table below.

C405905C12
4.771,0.5 5.188,0.75 0.417,0.25 1.865,0.656 2.281,0.906 0.417,0.25 1.021,0.771 1.333,0.969 0.313,0.198 10 false *a 3.844,0.646 4.156,0.844 0.313,0.198 10 false *b 1.948,0.698 2.26,0.896 0.313,0.198 10 false D97 4.865,0.542 5.323,0.74 0.458,0.198 10 false D20
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)
*b Front view of DLC3


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D97-3 (CANH) - D97-4 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D97-3 (CANH) - D97-6 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D97-4 (CANL) - D97-6 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D97-3 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D97-4 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FC CONTROL COMPUTER


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453214C01
1.5,0.146 1.927,0.375 0.427,0.229 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.625,0.198 1.906,0.375 0.281,0.177 10 false B1
*a Front view of wire harness connector
(to FC Control Computer)


Disconnect the FC control computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B1-65 (CA1H) - B1-64 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
B1-65 (CA1H) - B1-10 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B1-64 (CA1L) - B1-10 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B1-65 (CA1H) - B1-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B1-64 (CA1L) - B1-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the meter mirror sub-assembly connector.


c.
C380494C34
1.417,0.75 1.917,1 0.5,0.25 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.531,0.781 1.979,1 0.448,0.219 10 false D95
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D95-12 (MPX1) - D95-13 (MPX2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D95-12 (MPX1) - D20-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D95-13 (MPX2) - D20-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D95-12 (MPX1) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D95-13 (MPX2) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO RECEIVER ASSEMBLY (w/ Navigation System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the radio receiver assembly connectors.

C454953C03
1.938,0.094 2.302,0.302 0.365,0.208 5.167,0.063 5.531,0.271 0.365,0.208 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 2,0.104 2.313,0.302 0.313,0.198 10 false D61 5.229,0.073 5.542,0.271 0.313,0.198 10 false D64
*a Front view of wire harness connector
(to Radio Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D64-13 (CANH) - D64-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D64-13 (CANH) - D61-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D64-14 (CANL) - D61-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D64-13 (CANH) - D61-4 (+B1) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D64-14 (CANL) - D61-4 (+B1) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (w/o Navigation System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the radio and display receiver assembly connectors.

C454953C02
1.938,0.094 2.302,0.302 0.365,0.208 5.167,0.063 5.531,0.271 0.365,0.208 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 2,0.104 2.313,0.302 0.313,0.198 10 false D54 5.229,0.073 5.542,0.271 0.313,0.198 10 false D56
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D56-13 (CANH) - D56-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D56-13 (CANH) - D54-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D56-14 (CANL) - D54-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D56-13 (CANH) - D54-4 (+B1) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D56-14 (CANL) - D54-4 (+B1) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C404434C69
1.5,0.917 2,1.167 0.5,0.25 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.625,0.948 2.083,1.146 0.458,0.198 10 false D68
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D68-25 (CANP) - D68-26 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D68-25 (CANP) - D68-20 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D68-26 (CANN) - D68-20 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D68-25 (CANP) - D68-1 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D68-26 (CANN) - D68-1 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453194C01
1.448,0.156 1.885,0.406 0.438,0.25 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.542,0.208 1.865,0.385 0.323,0.177 10 false D41
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D41-29 (CANH) - D41-30 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
D41-29 (CANH) - D41-31 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D41-30 (CANL) - D41-31 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D41-29 (CANH) - D41-22 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D41-30 (CANL) - D41-22 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 60 seconds.


b.

Disconnect the airbag ECU assembly connector.

C409697C07
2.083,0.25 2.5,0.5 0.417,0.25 5.469,0.625 5.885,0.875 0.417,0.25 1.135,0.458 1.448,0.656 0.313,0.198 10 false *a 4.719,0.844 5.031,1.042 0.313,0.198 10 false *b 2.177,0.281 2.49,0.479 0.313,0.198 10 false D10 5.552,0.667 5.99,0.896 0.438,0.229 10 false D20
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D10-26 (CAFH) - D10-27 (CAFL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D10-26 (CAFH) - D10-33 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D10-27 (CAFL) - D10-33 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D10-26 (CAFH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D10-27 (CAFL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D10-20 (CANH) - D10-19 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D10-20 (CANH) - D10-33 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D10-19 (CANL) - D10-33 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D10-20 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D10-19 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (NO. 1 SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C303147C16
1.448,0.135 1.865,0.406 0.417,0.271 0.094,0.094 0.49,0.406 0.396,0.313 10 false *a 1.573,0.177 2.031,0.417 0.458,0.24 10 false A5
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (No. 1 Skid Control ECU))


Disconnect the brake booster with master cylinder assembly (No. 1 skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A5-38 (CA1H) - A5-39 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A5-38 (CA1H) - A5-28 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A5-39 (CA1L) - A5-28 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A5-38 (CA1H) - A5-14 (+BI1) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A5-39 (CA1L) - A5-14 (+BI1) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Powertrain Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A5-35 (CA2H) - A5-36 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A5-35 (CA2H) - A5-28 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A5-36 (CA2L) - A5-28 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A5-35 (CA2H) - A5-14 (+BI1) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A5-36 (CA2L) - A5-14 (+BI1) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (NO. 2 SKID CONTROL ECU)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C343810C22
1.396,0.656 1.896,0.948 0.5,0.292 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 1.563,0.729 2.042,0.948 0.479,0.219 10 false A6
*a Front view of wire harness connector
(to Brake Actuator Assembly (No. 2 Skid Control ECU))


Disconnect the brake actuator assembly (No. 2 skid control ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A6-27 (CANH) - A6-43 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A6-27 (CANH) - A6-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A6-43 (CANL) - A6-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A6-27 (CANH) - A6-14 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A6-43 (CANL) - A6-14 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Chassis Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A6-28 (CA3H) - A6-44 (CA3L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A6-28 (CA3H) - A6-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A6-44 (CA3L) - A6-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A6-28 (CA3H) - A6-14 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A6-44 (CA3L) - A6-14 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Powertrain Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A6-16 (CA2H) - A6-17 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A6-16 (CA2H) - A6-1 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A6-17 (CA2L) - A6-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A6-16 (CA2H) - A6-14 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A6-17 (CA2L) - A6-14 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEERING SENSOR


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C454958C01
0.552,1.615 1.073,1.865 0.521,0.25 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.677,1.656 1.104,1.865 0.427,0.208 10 false D34
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D34-3 (CANH) - D34-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D34-3 (CANH) - D34-6 (ESS) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D34-8 (CANL) - D34-6 (ESS) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D34-3 (CANH) - D34-4 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D34-8 (CANL) - D34-4 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RACK AND PINION POWER STEERING GEAR ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453192C01
1.448,0.302 1.885,0.542 0.438,0.24 1.49,2.281 1.927,2.521 0.438,0.24 0.115,0.125 0.396,0.313 0.281,0.188 10 false *a 1.542,0.365 1.885,0.563 0.344,0.198 10 false A79 1.594,2.333 1.938,2.531 0.344,0.198 10 false A80
*a Front view of wire harness connector
(to Rack and Pinion Power Steering Gear Assembly)


Disconnect the rack and pinion power steering gear assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A79-10 (CANH) - A79-11 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A79-10 (CANH) - A79-7 (PGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A79-11 (CANL) - A79-7 (PGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A79-10 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A79-11 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Chassis Local Bus Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A80-10 (CA2H) - A80-11 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A80-10 (CA2H) - A80-7 (PGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A80-11 (CA2L) - A80-7 (PGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A80-10 (CA2H) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A80-11 (CA2L) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453193C01
1.448,0.156 1.885,0.406 0.438,0.25 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.542,0.208 1.865,0.385 0.323,0.177 10 false D81
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D81-2 (CANH) - D81-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D81-2 (CANH) - D81-17 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D81-1 (CANL) - D81-17 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D81-2 (CANH) - D81-5 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D81-1 (CANL) - D81-5 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453208C01
1.448,0.156 1.885,0.406 0.438,0.25 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.542,0.208 1.865,0.385 0.323,0.177 10 false D86
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D86-1 (CANH) - D86-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D86-1 (CANH) - D86-18 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D86-2 (CANL) - D86-18 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D86-1 (CANH) - D86-4 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D86-2 (CANL) - D86-4 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY LH


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C406391C32
1.479,2.375 1.938,2.604 0.458,0.229 1.479,0.177 1.938,0.406 0.458,0.229 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 0.156,2.448 0.469,2.646 0.313,0.198 10 false *b 1.583,0.219 1.896,0.417 0.313,0.198 10 false A96 1.594,2.406 2.188,2.594 0.594,0.188 10 false D20
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
*b Front view of DLC3


Disconnect the headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A96-24 (CANH) - A96-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A96-24 (CANH) - A96-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A96-23 (CANL) - A96-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A96-24 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A96-23 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY RH


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C406391C33
1.479,2.375 1.938,2.604 0.458,0.229 1.479,0.177 1.938,0.406 0.458,0.229 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 0.156,2.448 0.469,2.646 0.313,0.198 10 false *b 1.583,0.219 1.896,0.417 0.313,0.198 10 false A97 1.583,2.417 2.26,2.635 0.677,0.219 10 false D20
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)
*b Front view of DLC3


Disconnect the headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A97-24 (CANH) - A97-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A97-24 (CANH) - A97-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A97-23 (CANL) - A97-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A97-24 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A97-23 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POSITION CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C371309C22
1.042,0.094 1.448,0.323 0.406,0.229 0.292,2.177 0.698,2.406 0.406,0.229 0.292,2.563 0.698,2.792 0.406,0.229 1.938,0.083 2.344,0.313 0.406,0.229 1.146,0.115 1.458,0.313 0.313,0.198 10 false L43 0.396,2.208 0.708,2.406 0.313,0.198 10 false L41 0.063,0.063 0.458,0.24 0.396,0.177 10 false *a 0.385,2.594 0.698,2.792 0.313,0.198 10 false L15 0.75,2.594 1.063,2.792 0.313,0.198 10 false *B 0.74,2.208 1.052,2.406 0.313,0.198 10 false *A 2.021,0.115 2.333,0.313 0.313,0.198 10 false L17 1.51,0.115 1.823,0.313 0.313,0.198 10 false *A 2.385,0.115 2.698,0.313 0.313,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Position Control ECU Assembly)


Disconnect the position control ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
L43-13 (CANP) - L43-14 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L43-13 (CANP) - L41-2 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L43-14 (CANN) - L41-2 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L43-13 (CANP) - L41-3 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L43-14 (CANN) - L41-3 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
L17-13 (CANP) - L17-14 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L17-13 (CANP) - L15-2 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-14 (CANN) - L15-2 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-13 (CANP) - L15-3 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L17-14 (CANN) - L15-3 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C454959C02
1.438,0.156 1.885,0.375 0.448,0.219 1.448,2.552 1.958,2.781 0.51,0.229 0.208,0.271 0.521,0.469 0.313,0.198 10 false *a 0.344,2.74 0.656,2.938 0.313,0.198 10 false *b 1.531,0.177 2,0.438 0.469,0.26 10 false D11 1.583,2.583 2.104,2.781 0.521,0.198 10 false D20
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3


Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D11-5 (CANH) - D11-4 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D11-5 (CANH) - D20-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D11-4 (CANL) - D20-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D11-5 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D11-4 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TIRE PRESSURE WARNING ECU AND RECEIVER


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the tire pressure warning ECU and receiver connector.

C406374C21
1.75,0.083 2.167,0.333 0.417,0.25 4.979,0.198 5.385,0.469 0.406,0.271 1.75,0.417 2.167,0.667 0.417,0.25 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *b 1.844,0.135 2.156,0.333 0.313,0.198 10 false G49 5.052,0.25 5.542,0.521 0.49,0.271 10 false D20 1.844,0.469 2.156,0.667 0.313,0.198 10 false G96 2.229,0.115 2.542,0.313 0.313,0.198 10 false *A 2.24,0.438 2.552,0.635 0.313,0.198 10 false *B
*A excluding JPD20R-CEDSSW (w/ Panic Switch) *B for JPD20R-CEDSSW (w/ Panic Switch)
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
excluding JPD20R-CEDSSW (w/ Panic Switch)
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G49-9 (CANH) - G49-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G49-9 (CANH) - G49-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G49-10 (CANL) - G49-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G49-9 (CANH) - G49-7 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G49-10 (CANL) - G49-7 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

for JPD20R-CEDSSW (w/ Panic Switch)
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G96-9 (CANH) - G96-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G96-9 (CANH) - G96-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G96-10 (CANL) - G96-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G96-9 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G96-10 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SHIFT CONTROL ECU


Refer to Terminals of ECU.

Click hereDrivetrain>Q710 (HYBRID TRANSMISSION / TRANSAXLE)>ELECTRONIC SHIFT LEVER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C371299C08
0.26,1.042 0.677,1.281 0.417,0.24 0.25,3.344 0.667,3.583 0.417,0.24 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.344,1.083 0.656,1.281 0.313,0.198 10 false D92 0.344,3.385 0.656,3.583 0.313,0.198 10 false D93
*a Front view of wire harness connector
(to Shift Control ECU)


Disconnect the shift control ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D92-9 (CA1H) - D92-8 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D92-9 (CA1H) - D93-6 (E01) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D92-8 (CA1L) - D93-6 (E01) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D92-9 (CA1H) - D93-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D92-8 (CA1L) - D93-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MULTIPLEX TILT AND TELESCOPIC ECU


Refer to Terminals of ECU.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453189C01
1.448,0.302 1.885,0.552 0.438,0.25 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.542,0.365 1.865,0.542 0.323,0.177 10 false D22
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the multiplex tilt and telescopic ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D22-3 (CANP) - D22-11 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D22-3 (CANP) - D22-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D22-11 (CANN) - D22-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D22-3 (CANP) - D22-2 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D22-11 (CANN) - D22-2 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYDROGEN FUEL CONTROL ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C441458C01
1.5,0.083 1.917,0.333 0.417,0.25 1.5,1.833 1.917,2.083 0.417,0.25 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.198,1.906 0.51,2.104 0.313,0.198 10 false *b 1.615,0.125 1.927,0.323 0.313,0.198 10 false G4 1.583,1.885 1.896,2.083 0.313,0.198 10 false D20
*a Front view of wire harness connector
(to Hydrogen Fuel Control ECU Assembly)
*b Front view of DLC3


Disconnect the hydrogen fuel control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G4-13 (CA1H) - G4-14 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G4-13 (CA1H) - G4-32 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-14 (CA1L) - G4-32 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G4-13 (CA1H) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G4-14 (CA1L) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INTERGRATION CONTROL SUB-ASSEMBLY (w/ Navigation System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>TOYOTA MULTI OPERATION TOUCH SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453222C01
1.5,0.26 2,0.521 0.5,0.26 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.594,0.302 1.979,0.479 0.385,0.177 10 false D105
*a Front view of wire harness connector
(to Integration Control Sub-Assembly)


Disconnect the integration control sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D105-32 (CANP) - D105-31 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D105-32 (CANP) - D105-20 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D105-31 (CANN) - D105-20 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D105-32 (CANP) - D105-1 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D105-31 (CANN) - D105-1 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FRONT MULTIPLEX NETWORK DOOR ECU LH (w/ Reverse Shift-linked Mirror)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453226C01
1.479,0.115 1.99,0.396 0.51,0.281 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.615,0.177 2.021,0.385 0.406,0.208 10 false E25
*a Front view of wire harness connector
(to Front multiplex network door ECU LH)


Disconnect the front multiplex network door ECU LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
E25-8 (CANP) - E25-7 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
E25-8 (CANP) - E25-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
E25-7 (CANN) - E25-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
E25-8 (CANP) - E25-6 (BDR) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
E25-7 (CANN) - E25-6 (BDR) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FRONT MULTIPLEX NETWORK DOOR ECU RH (w/ Reverse Shift-linked Mirror)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453226C02
1.521,0.104 1.979,0.344 0.458,0.24 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.667,0.167 1.979,0.354 0.313,0.188 10 false E7
*a Front view of wire harness connector
(to Front Multiplex Network Door ECU RH)


Disconnect the front multiplex network door ECU RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
E7-8 (CANP) - E7-7 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
E7-8 (CANP) - E7-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
E7-7 (CANN) - E7-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
E7-8 (CANP) - E7-6 (BDR) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
E7-7 (CANN) - E7-6 (BDR) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR MULTIPLEX NETWORK DOOR ECU LH (w/ Door Closer System)


Refer to Terminals of ECU.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453226C03
1.521,0.104 1.979,0.344 0.458,0.24 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.615,0.135 1.927,0.323 0.313,0.188 10 false F16
*a Front view of wire harness connector
(to Rear Multiplex Network Door ECU LH)


Disconnect the rear multiplex network door ECU LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
F16-8 (CANP) - F16-7 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F16-8 (CANP) - F16-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F16-7 (CANN) - F16-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F16-8 (CANP) - F16-4 (BDR) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F16-7 (CANN) - F16-4 (BDR) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR MULTIPLEX NETWORK DOOR ECU RH (w/ Double Locking System)


Refer to Terminals of ECU.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453226C04
1.521,0.104 1.979,0.344 0.458,0.24 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.667,0.146 1.979,0.333 0.313,0.188 10 false F5
*a Front view of wire harness connector
(to Rear Multiplex Network Door ECU RH)


Disconnect the rear multiplex network door ECU RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
F5-8 (CANP) - F5-7 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
F5-8 (CANP) - F5-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F5-7 (CANN) - F5-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
F5-8 (CANP) - F5-4 (BDR) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
F5-7 (CANN) - F5-4 (BDR) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




STEREO COMPONENT EQUALIZER ASSEMBLY (w/ ASC System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>ASC SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C453227C01
1.49,0.135 1.969,0.385 0.479,0.25 0.135,0.125 0.448,0.281 0.313,0.156 10 false *a 1.563,0.188 1.948,0.375 0.385,0.188 10 false D104
*a Front view of wire harness connector
(to Stereo Component Equalizer Assembly)


Disconnect the stereo component equalizer assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D104-4 (CANH) - D104-12 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D104-4 (CANH) - D104-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D104-12 (CANL) - D104-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D104-4 (CANH) - D104-3 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D104-12 (CANL) - D104-3 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Luggage Compartment Door Closer System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>LUGGAGE COMPARTMENT DOOR CLOSER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C369151C53
1.5,0.781 2,1.063 0.5,0.281 0.125,0.135 0.604,0.323 0.479,0.188 10 false *a 1.615,0.833 2.094,1.021 0.479,0.188 10 false G15
*a Front view of wire harness connector
(to Multiplex Network Door ECU)


Disconnect the multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
G15-10 (CANP) - G15-11 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
G15-10 (CANP) - G15-1 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G15-11 (CANN) - G15-1 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G15-10 (CANP) - G15-19 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G15-11 (CANN) - G15-19 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OCCUPANT DETECTION ECU (w/ Occupant Classification System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C406388C15
1.479,0.135 1.906,0.385 0.427,0.25 1.51,1.865 1.938,2.115 0.427,0.25 0.646,0.333 0.958,0.531 0.313,0.198 10 false *a 0.677,1.865 0.99,2.063 0.313,0.198 10 false *b 1.563,0.188 1.875,0.385 0.313,0.198 10 false L20 1.563,1.906 2.052,2.188 0.49,0.281 10 false D20
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of DLC3


Disconnect the occupant detection ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
L20-5 (CANH) - L20-4 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L20-5 (CANH) - L20-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L20-4 (CANL) - L20-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L20-5 (CANH) - D20-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L20-4 (CANL) - D20-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher