Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2020.05–2021.07
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0386559 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 16575C 1.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

a.

Install the No. 1 water hose clamp bracket with the bolt to the timing chain case assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13471 2.INSTALL CRANKSHAFT PULLEY (for Automatic Transmission)

Hide 13407 3.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY (for Manual Transmission)

Hide 13496 4.INSTALL CRANKSHAFT PULLY COVER (for Automatic Transmission)

Hide 88451B 5.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 11382C 6.INSTALL CAMSHAFT OIL SEAL RETAINER

NOTICE:

If the camshaft oil seal retainer is dropped, replace it with a new one.


a.

Before installing a new camshaft oil seal retainer, clean the installation surface of the No. 3 camshaft bearing cap and cylinder head sub-assembly and remove any foreign matter.


b.
A343512C01
2.594,0.823 2.594,0.146 2.594,0.146 2.781,0.146 true 0.563,1.292 0.76,1.292 0.76,1.292 1.313,2.333 true 2.802,0.917 2.802,0.385 2.802,0.385 2.99,0.385 true 3.021,0.302 3.333,0.458 0.313,0.156 10 false *1 2.604,2.99 2.917,3.146 0.313,0.156 10 false *a 0.271,1.198 0.729,1.396 0.458,0.198 10 false SST 2.833,0.063 3.292,0.26 0.458,0.198 10 false SST
*1 Camshaft Oil Seal Retainer
*a Depth


Using SST and a hammer, tap in a new camshaft oil seal retainer to the No. 3 camshaft bearing cap and cylinder head sub-assembly as shown in the illustration.

SST
09223-46011  

Standard depth:

0 to 0.8 mm (0 to 0.0315 in.)



Hide 29300 7.INSTALL VACUUM PUMP ASSEMBLY

a.
A343513

Coat 2 new O-rings with engine oil, and install them to the vacuum pump assembly.


b.
A343514N01
2.615,0.469 2.427,0.469 2.427,0.469 2.281,0.885 true 1.198,1.781 1.198,1.281 true 1.156,1.802 1.333,1.99 0.177,0.188 10 true A 2.667,0.385 2.844,0.573 0.177,0.188 10 true B

Install the vacuum pump assembly so that the coupling teeth of the vacuum pump assembly labeled A and the groove of the No. 2 camshaft labeled B can engage.


c.

Install the vacuum pump assembly with the 3 bolts to the cylinder head sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25706 8.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 1 vacuum transmitting pipe sub-assembly with the 3 bolts to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

w/ EGR Cooler:

Connect the No. 1 vacuum transmitting hose to the vacuum pump assembly.


Hide 16620 9.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16603 10.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16321 12.INSTALL WATER INLET

a.

Install the water inlet with the 3 bolts to the timing chain cover sub-assembly.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16304 13.INSTALL WATER OUTLET SUB-ASSEMBLY

a.

Install a new gasket and the water outlet sub-assembly with the 4 bolts and 2 nuts to the timing chain cover sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16207 14.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 2 water by-pass pipe sub-assembly with the 2 bolts to the engine water pump assembly and water inlet.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 3 water by-pass hose to the water outlet sub-assembly, and slide the clamp to secure the hose.


Hide 83530 15.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 15407 16.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17141 17.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 17141 20.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 87101 22.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

a.
A347302N01
2.51,1.333 2.667,1.531 0.156,0.198 10 true 1 0.802,0.063 0.958,0.26 0.156,0.198 10 true 2 0.896,1.458 1.052,1.656 0.156,0.198 10 true 3 2.385,0.198 2.594,0.385 0.208,0.188 10 true 4

Temporarily install the No. 1 viscous heater bracket sub-assembly with the 4 bolts to the cylinder block sub-assembly and timing chain cover sub-assembly.


b.

Tighten the 4 bolts in the sequence shown in the illustration to install the No. 1 viscous heater bracket sub-assembly.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 16268 24.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the 3 bolts to the timing chain cover sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the No. 1 water by-pass pipe.



Hide 25.INSTALL WATER BY-PASS HOSE (for Water Cooled Compressor Housing Turbocharger)

Hide 12261 27.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

Hide 89463C 28.INSTALL NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 17291 29.INSTALL TURBINE OUTLET ELBOW (w/o EGR Cooler)

a.

Set a new gasket and the turbine outlet elbow to the turbocharger sub-assembly.


b.

Temporarily install the exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow with the 3 bolts.


c.
A407026C01
2.448,0.615 2.281,0.417 2.281,0.417 2.177,0.417 false 2.677,1.365 2.677,1.646 true 1.99,0.333 2.208,0.5 0.219,0.167 10 false *1 2.271,1.188 2.479,1.344 0.208,0.156 10 false *2 2.896,1.302 3.115,1.458 0.219,0.156 10 false *3 2.635,1.667 2.854,1.833 0.219,0.167 10 false *4 0.25,1.792 0.563,1.969 0.313,0.177 10 false 90°
*1 Exhaust Pipe Clamp
*2 Turbine Outlet Elbow
*3 Turbocharger Sub-assembly
*4 Gasket


Install a new exhaust pipe clamp to the turbine outlet elbow with a new nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


d.
A443334N01
2.083,1.188 2.24,1.385 0.156,0.198 10 true 1 1.24,1.667 1.396,1.865 0.156,0.198 10 true 2 0.563,1.281 0.708,1.438 0.146,0.156 10 true 3

Tighten the 3 bolts and install the exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 31.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY (w/o EGR Cooler)

a.

Temporarily install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow with the bolt and 2 new nuts.


b.
A443333N01
0.854,0.083 0.979,0.25 0.125,0.167 10 true 1 0.719,1.573 0.854,1.729 0.135,0.156 10 true 2 2.896,1.76 3.021,1.927 0.125,0.167 10 true 3

Tighten the bolt and 2 nuts and install the No. 2 exhaust pipe support stay to the cylinder block sub-assembly and turbine outlet elbow in the order shown in the illustration.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 89463C 33.CONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

a.

Install the exhaust sensor clamp bracket to the cylinder head sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Attach the 4 clamps and connect the No. 1 nitrogen oxides sensor.


Hide 17271 34.INSTALL NO. 1 TURBO INSULATOR (w/o EGR Cooler)

a.

Install the No. 1 turbo insulator to the exhaust manifold and turbocharger sub-assembly with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17167 36.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/o EGR Cooler)

a.

Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 89467B 38.INSTALL AIR FUEL RATIO SENSOR (w/o Exhaust Gas Temperature Sensor for EGR)

Hide 16281 40.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

a.

Connect the No. 4 water by-pass hose to the No. 1 injector holder, and slide the clamp to secure the hose.


Hide 16282 41.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)

a.

Attach the clamp and install the No. 5 water by-pass hose to the No. 1 water hose clamp bracket.


b.

Connect the No. 5 water by-pass hose to the No. 1 injector holder and water outlet sub-assembly, and slide the 2 clamps to secure the hose.


Hide 12229 42.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

Hide 89422P 43.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 16632B 44.INSTALL NO. 2 IDLER PULLEY BRACKET (w/o Air Conditioning System)

NOTICE:

Install the No. 2 idler pulley bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A354154

Temporarily install the No. 2 idler pulley bracket with the 2 bolts to the cylinder block sub-assembly.

HINT:

Temporarily install the No. 2 idler pulley bracket with the 2 bolts so that the No. 2 idler pulley bracket can be moved by hand.



b.
A354155C01
1.333,3.167 1.542,3.354 0.208,0.188 10 true *a 2.115,4.063 2.427,4.219 0.313,0.156 10 false *b 0.563,2.49 0.875,2.646 0.313,0.156 10 false *c 0.99,1.896 1.167,2.073 0.177,0.177 10 true A 2.771,3.156 2.979,3.344 0.208,0.188 10 true *a
*a No Clearance
*b Push
*c Front


Push the No. 2 idler pulley bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:

Make sure there is no clearance between the cylinder block sub-assembly and No. 2 idler pulley bracket as shown in the illustration.



c.
A354156N01
2.844,0.833 3.031,1.01 0.188,0.177 10 true 2 1.667,0.094 1.854,0.271 0.188,0.177 10 true 1

Uniformly tighten the 2 bolts in the order shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 88431 45.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

NOTICE:

Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A354055

Temporarily install the No. 1 compressor mounting bracket with the 2 bolts to the cylinder block sub-assembly.

HINT:

Temporarily install the No. 1 compressor mounting bracket with the 2 bolts so that the No. 1 compressor mounting bracket can be moved by hand.



b.
A354056C01
1.156,3.313 1.344,3.479 0.188,0.167 10 true *a 1.906,4.229 2.219,4.385 0.313,0.156 10 false *b 0.552,2.479 0.865,2.635 0.313,0.156 10 false *c 0.698,1.219 0.854,1.417 0.156,0.198 10 true A 2.51,4.229 2.823,4.385 0.313,0.156 10 false *b 2.667,3.313 2.854,3.479 0.188,0.167 10 true *a 3.229,3.313 3.417,3.479 0.188,0.167 10 true *a
*a No Clearance
*b Push
*c Front


Push the No. 1 compressor mounting bracket toward the cylinder block sub-assembly as shown in the illustration and tighten bolt A.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

HINT:

Make sure there is no clearance between the cylinder block sub-assembly and No. 1 compressor mounting bracket as shown in the illustration.



c.
A354057N01
2.615,1.406 2.771,1.604 0.156,0.198 10 true 3 3.031,0.396 3.188,0.594 0.156,0.198 10 true 2 0.844,0.281 1,0.479 0.156,0.198 10 true 1

Uniformly tighten the 3 bolts in the order shown in the illustration.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 88320 46.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 16025 47.INSTALL NO. 5 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A444784C01
0,0 0,0 false
V100135

Bolt A
V100136

Bolt B


for Laminated EGR Pre-cooler:

Install a new gasket and the No. 5 water by-pass pipe sub-assembly with the 4 bolts to the cylinder block sub-assembly.

Torque:
for bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install a new gasket and the No. 5 water by-pass pipe sub-assembly with the 3 bolts to the cylinder block sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Make sure that the claw of the gasket faces the No. 5 water by-pass pipe sub-assembly.



Hide 23780B 48.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o Pressurized Fuel Filter)

a.

Install the No. 3 nozzle leakage pipe with the 2 nuts to the cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23300D 49.INSTALL DIESEL FUEL FILTER ASSEMBLY (w/ Pressurized Fuel Filter)

a.

Install the diesel fuel filter assembly with the 2 nuts to the cylinder block sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 44781 50.INSTALL HOSE BRACKET

a.

Install the hose bracket with the 2 bolts to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19850 51.INSTALL GLOW PLUG ASSEMBLY

Hide 19871 52.INSTALL NO. 1 GLOW PLUG CONNECTOR

Hide 23810A 53.INSTALL COMMON RAIL ASSEMBLY

Hide 23701 54.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 55.TIGHTEN INJECTOR ASSEMBLY

Hide 23701 56.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 57.INSTALL WIRING HARNESS CLAMP BRACKET

a.
A343500N01
0.24,0.969 0.396,1.167 0.156,0.198 10 true A 3.135,1.021 3.313,1.188 0.177,0.167 10 true B

Install the 2 wiring harness clamp brackets with the 2 bolts to the cylinder head cover sub-assembly.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 23760 58.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 60.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23770 62.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23804C 63.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 23815D 64.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804D 65.INSTALL NO. 4 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804D 66.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

Hide 23271H 67.INSTALL NO. 1 FUEL HOSE

Hide 23273H 68.INSTALL NO. 2 FUEL HOSE

Hide 23243B 69.INSTALL FUEL PUMP MOTOR WIRE

Hide 22803 70.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 72.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23812D 73.INSTALL NO. 2 FUEL PIPE

a.

Install the No. 2 fuel pipe with the bolt to the manifold stay.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.


Hide 11409 74.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25617 75.INSTALL EGR HOLE COVER PLATE (w/o EGR System)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the 2 EGR cooler hole plates to the intake manifold and exhaust manifold with 4 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 25624 76.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY (w/o EGR System)

a.

Temporarily install the EGR valve adapter sub-assembly to the intake manifold with the 4 bolts.


b.
A398418N01
0.594,1.948 0.729,2.104 0.135,0.156 10 true 1 2.771,1.854 2.906,2.01 0.135,0.156 10 true 2 3.104,0.719 3.24,0.875 0.135,0.156 10 true 3 0.156,0.542 0.292,0.698 0.135,0.156 10 true 4

Tighten the 4 bolts in the order shown in the illustration.

NOTICE:

Make sure to tighten the bolts in the order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 77.INSTALL EGR VALVE ADAPTER SUB-ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

a.
A365517N01
0.479,0.646 0.646,0.802 0.167,0.156 10 true 4 2.781,1.573 2.969,1.76 0.188,0.188 10 true 3 2.177,1.885 2.365,2.063 0.188,0.177 10 true 2 0.938,1.948 1.115,2.125 0.177,0.177 10 true 1

Temporarily install the EGR valve adapter sub-assembly with electric EGR control valve assembly to the intake manifold with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

NOTICE:

Make sure to tighten the bolts in the order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25800 78.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System with EGR Cooler)

Hide 16209 79.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 4 water by-pass pipe sub-assembly with the 2 bolts to the intake manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

for Cold Area Specification Vehicles:

Attach the clamp and connect the No. 11 water by-pass hose to the diesel throttle body assembly.


c.

Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.


d.

Connect the No. 7 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


e.

Connect the No. 6 water by-pass hose to the No. 4 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


Hide 25804 80.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 25601 81.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (for Laminated EGR Pre-cooler)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the EGR pipe with cooler sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the EGR pipe with cooler sub-assembly to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the water hose to the EGR pipe with cooler sub-assembly and No. 5 water by-pass pipe, and slide the 2 clamps to secure the hose.


Hide 25601 82.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System)

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the No. 1 EGR pipe with the bolt and 4 new nuts to the exhaust manifold, electric EGR control valve assembly and No. 1 vacuum transmitting pipe sub-assembly.

Torque:
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for nut : 29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 27148A 83.INSTALL CONNECTING WIRE

a.

Attach the 2 clamps and install the connecting wire to the hose bracket.


b.

Connect the connector to the common rail assembly.


Hide 16206B 84.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.

Install the No. 3 water by-pass pipe sub-assembly to the EGR valve adapter sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

w/ EGR System:

i.

Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


ii.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.



c.

Connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 16206B 85.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 89425D 87.INSTALL NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 12631A 91.INSTALL ENGINE COVER BRACKET (for Air Cooled Type Intercooler)

a.

Install the engine cover bracket with the 2 bolts to the cylinder head sub-assembly and hose bracket.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17945 92.INSTALL INTERCOOLER SUPPORT BRACKET (for Water Cooled Type Intercooler)

a.

Install the intercooler support bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25734 94.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)

Hide 25733A 95.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)

Hide 89425 98.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 89481B 99.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 26100G 101.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 82121 102.INSTALL ENGINE WIRE

Hide 12632 103.INSTALL NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)