Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function) › from 2016.08
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Engine does not Start  


DESCRIPTION

When the key is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P or N*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch.

*1: except Manual Transaxle

*2: for Manual Transaxle


HINT:
·

When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).

·

When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.



Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start
Power Source Control:
·

Stop Light Switch1*1

·

Steering Unlock Switch

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal*1

·

Neutral SW/ Clutch SW

·

Starter Request Signal


Entry&Start:
·

Immobiliser

·

S Code Check*2

·

L Code Check

·

Engine Start Request


Starting Control:
·

Ignition

·

Starter SW

·

Shift Position P or N*1


-

·

*1: except Manual Transaxle

·

*2: w/ ID Code Box (Immobiliser Code ECU)


WIRING DIAGRAM

Refer to "System Diagram".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>SYSTEM DIAGRAM

C346900E02
2.833,1.115 3.292,1.313 0.458,0.198 10 false A61*1 2.833,1.271 3.771,1.479 0.938,0.208 10 false A62*2, *3, *4 2.833,1.438 3.292,1.635 0.458,0.198 10 false ECM 3.677,0.24 4.135,0.438 0.458,0.198 10 false 35*1 3.677,0.417 4.135,0.615 0.458,0.198 10 false 11*2 3.677,0.635 4.135,0.833 0.458,0.198 10 false 9*3 3.667,0.792 4.125,0.99 0.458,0.198 10 false 48*4 5.24,0.406 5.698,0.604 0.458,0.198 10 false 5 5.365,1.115 5.823,1.313 0.458,0.198 10 false A100 5.417,2.281 5.875,2.479 0.458,0.198 10 false STP1 5.167,2.177 5.625,2.375 0.458,0.198 10 false 18 5.375,2.865 5.833,3.063 0.458,0.198 10 false G82 5.375,3.031 6.969,3.417 1.594,0.385 10 false Certification ECU (Smart Key ECU Assembly) 5.229,3.906 5.688,4.104 0.458,0.198 10 false 8 5.427,4.042 5.885,4.24 0.458,0.198 10 false STP 5.208,4.615 5.667,4.813 0.458,0.198 10 false G35 5.198,4.771 7.104,5.177 1.906,0.406 10 false Shift Lock Control ECU (Lower Shift Lever Assembly) 3.677,3.917 4.135,4.115 0.458,0.198 10 false 12 3.313,4.042 3.771,4.24 0.458,0.198 10 false STP 2.729,4.646 3.188,4.844 0.458,0.198 10 false B79 2.719,4.813 4.083,5.219 1.365,0.406 10 false Transmission Control ECU Assembly*5 2.813,2.875 3.271,3.073 0.458,0.198 10 false A77 2.792,3.031 3.917,3.396 1.125,0.365 10 false Stop Light Switch Assembly 2.677,2.448 3.135,2.646 0.458,0.198 10 false 2 2.854,2.563 3.313,2.76 0.458,0.198 10 false GND 2.875,2.031 3.333,2.229 0.458,0.198 10 false B 2.677,1.927 3.135,2.125 0.458,0.198 10 false 7 1.917,2.208 2.375,2.406 0.458,0.198 10 false STOP 0.51,2.042 1.458,2.229 0.948,0.188 10 false from Battery 3.49,2.281 3.948,2.479 0.458,0.198 10 false L 3.698,2.177 4.156,2.375 0.458,0.198 10 false 3 0.354,3.771 2.073,4.031 1.719,0.26 10 false *1: for 2AD-FHV, 2AD-FTV 0.344,4.156 1.531,4.354 1.188,0.198 10 false *2: for 2AR-FE 0.344,4.563 2.01,4.792 1.667,0.229 10 false *3: for 3ZR-FE, 3ZR-FAE 0.344,4.948 1.208,5.125 0.865,0.177 10 false *4: for 2WW 5.344,1.281 6.917,1.646 1.573,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 3.313,0.531 3.771,0.729 0.458,0.198 10 false STP 5.427,0.531 5.885,0.729 0.458,0.198 10 false STP2 0.313,5.271 2.229,5.604 1.917,0.333 10 false *5: except Manual Transaxle 4.094,3.927 4.552,4.125 0.458,0.198 10 false *5

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly), ECM or ID code box (immobiliser code ECU) (w/ ID code box (immobiliser code ECU)), refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:

If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases.


PROCEDURE

1.CHECK BATTERY
a.

Measure the battery voltage.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

·

If the battery voltage is less than 11 V, charge or replace it.




Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Proceed to
OK
NG



OK

3.CHECK WAVE ENVIRONMENT

NG

GO TO DTC CHART

3.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver (RF band).


OK:

Engine starts.



Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

4.CHECK ENGINE SWITCH CONDITION
4.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P (except Manual Transaxle).


c.

With the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) released, check that pressing the engine switch causes the power source mode to change.

Result:
Proceed to
Off → on (ACC) → on (IG) → off
Power source mode does not change to on (ACC) and on (IG)
Power source mode changes to on (IG) but not to on (ACC)
Power source mode changes to on (ACC) but not to on (IG)




Off → on (ACC) → on (IG) → off

5.CHECK CRANKING FUNCTION

Power source mode does not change to on (ACC) and on (IG)

Power source mode changes to on (IG) but not to on (ACC)

Power source mode changes to on (ACC) but not to on (IG)

5.CHECK CRANKING FUNCTION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P (except Manual Transaxle).


c.

Depress the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle).


d.

Confirm that the key warning light is displayed, and then press the engine switch and check that the engine cranks.


OK:

Engine cranks.


Result:
Proceed to
OK
NG (for ECD system)
NG (for SFI system)



OK

6.CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)

NG (for ECD system)

NG (for SFI system)

6.CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P (except Manual Transaxle).


c.

Press the engine switch with the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

HINT:

It is determined that the engine immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


OK:

Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).



Result:
Proceed to
OK
NG (w/ ID Code Box (Immobiliser Code ECU))
NG (w/o ID Code Box (Immobiliser Code ECU))



OK

7.CHECK COMBINATION METER ASSEMBLY

NG (w/ ID Code Box (Immobiliser Code ECU))

22.READ VALUE USING GTS (S CODE CHECK)

NG (w/o ID Code Box (Immobiliser Code ECU))

23.CHECK STEERING LOCK
7.CHECK COMBINATION METER ASSEMBLY
a.

Get into the vehicle while carrying the key, move the shift lever to P (except Manual Transaxle), press the engine switch while depressing the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) and check that the combination meter indicator changes.

HINT:

If the key warning light is displayed when the procedure above is performed, the P, N and brake signals*1 or clutch signals*2 can be considered to be normal.

*1: except Manual Transaxle

*2: for Manual Transaxle



OK:

The key warning light is displayed.



Result:
Proceed to
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)



OK

8.READ VALUE USING GTS (STARTER SW)

NG (except Manual Transaxle)

13.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)

NG (for Manual Transaxle)

19.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
8.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Starting Control / Data List.


e.

Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P (except Manual Transaxle), press the engine switch while depressing the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) and confirm that the Data List item changes.

Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter operation request ON or OFF ON: Starter operation requested
OFF: Starter operation not requested
When malfunctioning, the engine will not crank
Body Electrical > Starting Control > Data List
Tester Display
Starter SW
50003 221 1
OK:

The Data List item changes.



Result:
Proceed to
OK
NG



OK

9.INSPECT ST RELAY (STARTER RELAY ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT ST RELAY (STARTER RELAY ASSEMBLY)

OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)

NG

REPLACE ST RELAY (STARTER RELAY ASSEMBLY)

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)
a.
B268625C43
0.521,1.323 0.958,1.563 0.438,0.24 1.854,1.427 2.344,1.323 true 1.385,1.875 1.583,1.469 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 2.375,1.25 2.76,1.396 0.385,0.146 10 STAR 0.594,1.375 1.021,1.531 0.427,0.156 10 G82 1.229,1.885 1.615,2.031 0.385,0.146 10 STA
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Move the shift lever to P or N.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - Body ground 20°C (68°F) 100 to 150 Ω
G82-7 (STA) - Body ground



Result:
Proceed to
OK
NG



OK

11.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT STARTER ASSEMBLY

OK

12.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY (STARTER RELAY ASSEMBLY))

NG

12.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY (STARTER RELAY ASSEMBLY))
a.

Remove the starter assembly from the vehicle to perform an inspection.


b.

Remove the ST relay (starter relay assembly) from the No. 2 engine room relay block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 2AR-FE:
Tester Connection Condition Specified Condition
C5-1 - Body ground Always 11 to 14 V
5 - Body ground

for 3ZR-FAE (w/o Stop and Start System), 3ZR-FE:
Tester Connection Condition Specified Condition
C6-1 - Body ground Always 11 to 14 V
5 - Body ground

for 2AD-FHV, 2AD-FTV:
Tester Connection Condition Specified Condition
C4-1 - Body ground Always 11 to 14 V
5 - Body ground

for 2WW:
Tester Connection Condition Specified Condition
C8-1 - Body ground Always 11 to 14 V
5 - Body ground

for 3ZR-FAE (w/ Stop and Start System):
Tester Connection Condition Specified Condition
B96-1 (B) - Body ground Always 11 to 14 V
5 - Body ground



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE:
Tester Connection Condition Specified Condition
3 - B6-1 Always Below 1 Ω
3 or B6-1 - Body ground 10 kΩ or higher

for 3ZR-FAE (w/o Stop and Start System), 3ZR-FE:
Tester Connection Condition Specified Condition
3 - B6-1 Always Below 1 Ω
3 or B6-1 - Body ground 10 kΩ or higher

for 2AD-FHV, 2AD-FTV:
Tester Connection Condition Specified Condition
3 - B6-1 Always Below 1 Ω
3 or B6-1 - Body ground 10 kΩ or higher

for 2WW:
Tester Connection Condition Specified Condition
3 - B117-1 Always Below 1 Ω
3 or B117-1 - Body ground 10 kΩ or higher

for 3ZR-FAE (w/ Stop and Start System):
Tester Connection Condition Specified Condition
3 - B87-2(SL1) Always Below 1 Ω
3 or B87-2(SL1) - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control and Starting Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW Shift position (P, N) ON or OFF ON: Shift lever in P or N
OFF: Shift lever not in P or N
·

Use this item to determine whether the park/neutral position switch is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
Body Electrical > Starting Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position P or N Condition of park/neutral position switch ON or OFF ON: Shift lever in P or N
OFF: Shift lever not in P or N
When malfunctioning, the engine will not crank.
Body Electrical > Starting Control > Data List
Tester Display
Shift Position P or N
50003 221 2
OK:

The item in the Data List changes according to the shift position.



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (STOP LIGHT SWITCH1)

NG

17.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY
14.READ VALUE USING GTS (STOP LIGHT SWITCH1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G82 connector from certification ECU (smart key ECU assembly).


b.

Disconnect the A77 connector from the stop light switch assembly.


c.

Disconnect the A61*1 or A62*2 connector from ECM.

*1: for 2AD-FHV, 2AD-FTV

*2: except 2AD-FHV, 2AD-FTV



d.

Disconnect the A100 connector from skid control ECU (brake actuator assembly).


e.

Disconnect the G35 connector from shift lock control ECU (transmission floor shift assembly).


f.

Disconnect the B79 connector from transmission control ECU assembly.


g.
C346899C01
1.5,0.292 1.906,0.563 0.406,0.271 1.844,1.99 1.729,1.99 1.729,1.99 1.542,1.344 true 0.646,1.979 0.802,1.979 0.802,1.979 1.26,1.354 true 2.625,1.99 2.51,1.99 2.51,1.99 2.323,1.344 true 0.177,0.188 0.49,0.344 0.313,0.156 10 false *a 1.583,0.344 2.042,0.542 0.458,0.198 10 false A77 0.302,1.885 0.76,2.083 0.458,0.198 10 false GND 1.896,1.896 2.177,2.083 0.281,0.188 10 false L 2.677,1.906 3.135,2.104 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) inthe table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-7 (B) - Body ground Always 11 to 14 V



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-18 (STP1) - A77-3 (L) Always Below 1 Ω
G82-18 (STP1) or A77-3 (L) - Body ground 10 kΩ or higher
A77-2 (GND) - Body ground Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

16.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

17.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Disconnect the B36*1 or B101*2 connector from the park/neutral position switch assembly.

*1: except 3ZR-FE

*2: for 3ZR-FE



b.

Inspect the park/neutral position switch assembly.

·

for Park/neutral position switch assembly (for U660F)

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION

·

for Park/neutral position switch assembly (for U760E)

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION

·

for Park/neutral position switch assembly (for U760F)

Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION

·

for Park/neutral position switch assembly (for K111)

Click hereDrivetrain>K111 MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION

·

for Park/neutral position switch assembly (for K111F)

Click hereDrivetrain>K111F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION

·

for Park/neutral position switch assembly (for K114F)

Click hereDrivetrain>K114F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG




OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

NG

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B36*1 or B101*2 connector from the park/neutral position switch.

*1: except 3ZR-FE

*2: for 3ZR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 3ZR-FE:
Tester Connection Condition Specified Condition
G82-5 (STAR) - B36-4 (B) Always Below 1 Ω
G82-5 (STAR) or B36-4 (B) - Body ground Always 10 kΩ or higher

for 3ZR-FE:
Tester Connection Condition Specified Condition
G82-5 (STAR) - B101-4 (B) Always Below 1 Ω
G82-5 (STAR) or B101-4 (B) - Body ground Always 10 kΩ or higher



d.
B268625C39
0.479,1.115 0.906,1.344 0.427,0.229 2.26,1.75 1.844,1.469 false 0.063,0.042 0.375,0.198 0.313,0.156 10 *a 0.552,1.156 0.865,1.313 0.313,0.156 10 G82 2.281,1.76 2.781,1.969 0.5,0.208 10 STAR
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Reconnect the B36*1 or B101*2 connector from the park/neutral position switch assembly.

*1: except 3ZR-FE

*2: for 3ZR-FE



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G82-5 (STAR) - Body ground Engine switch pressed and held with brake pedal depressed (starter on) → Engine switch released after approximately 1 second elapses (starter off) 6 V or higher* → 1.5 V or less


HINT:

*: When the engine is cranking, the battery voltage may momentarily drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

19.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Power Source Control/ Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral SW/ Clutch SW State of clutch pedal ON or OFF ON: Clutch pedal depressed
OFF: Clutch pedal released
·

Use this item to determine whether the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


Body Electrical > Power Source Control > Data List
Tester Display
Neutral SW/ Clutch SW
50003 223 6
OK:

ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the condition of the clutch pedal.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

20.INSPECT CLUTCH START SWITCH ASSEMBLY
20.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A4*1 or F2*2 clutch start switch connector

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD:
Tester Connection Condition Specified Condition
G82-5 (STAR) - F2-2 Always Below 1 Ω
G82-5 (STAR) or F2-2 - Body ground Always 10 kΩ or higher

for LHD:
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2 Always Below 1 Ω
G82-5 (STAR) or A4-2 - Body ground Always 10 kΩ or higher



d.
B268625C39
0.479,1.115 0.906,1.344 0.427,0.229 2.26,1.75 1.844,1.469 false 0.063,0.042 0.375,0.198 0.313,0.156 10 *a 0.552,1.156 0.865,1.313 0.313,0.156 10 G82 2.281,1.76 2.781,1.969 0.5,0.208 10 STAR
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Reconnect the A4*1 or F2*2 clutch start switch assembly connector.

*1: for LHD

*2: for RHD



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-5 (STAR) - Body ground Engine switch pressed and held with clutch start switch depressed (starter on) → Engine switch released after approximately 1 second elapses (starter off) 6 V or higher* → 1.5 V or less


HINT:

*: When the engine is cranking, the battery voltage may momentarily drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

22.READ VALUE USING GTS (S CODE CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
HINT:
Reasons for verification failure:
·

The certification ECU (smart key ECU assembly) or the ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.



OK:

OK (S code certification result normal) appears on the screen.



Result:
Proceed to
OK
NG



OK

23.CHECK STEERING LOCK

NG

28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
23.CHECK STEERING LOCK
a.

Check that the steering unlocks when the engine switch is turned on (ACC).

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

24.READ VALUE USING GTS (IMMOBILISER)

NG

26.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
24.READ VALUE USING GTS (IMMOBILISER)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system determined by certification ECU (smart key ECU assembly) Set or Unset Set: Engine immobiliser system set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser system unset (engine start permitted) (engine switch on(ACC) or on (IG))
The engine cannot be started when Set is displayed.
HINT:
·

The security indicator light blinks when Set is displayed.

·

The security indicator light is linked with set/unset of the immobiliser and not linked with steering lock/unlock.



Body Electrical > Entry&Start > Data List
Tester Display
Immobiliser
50003 125 34
OK:

The Data List item changes to "Unset" when the engine switch is turned on (ACC) or on (IG).



Result:
Proceed to
OK
NG (w/ ID Code Box (Immobiliser Code ECU))
NG (w/o ID Code Box (Immobiliser Code ECU))



OK

25.READ VALUE USING GTS (STARTER REQUEST SIGNAL)

NG (w/ ID Code Box (Immobiliser Code ECU))

28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG (w/o ID Code Box (Immobiliser Code ECU))

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

25.READ VALUE USING GTS (STARTER REQUEST SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Engine start request signal status ON or OFF
except Manual Transaxle

ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held

OFF: After approx. 1 sec. has elapsed, the engine switch is released


for Manual Transaxle

ON: With the clutch pedal depressed, the engine switch is pressed and held

OFF: After approx. 1 sec. has elapsed, the engine switch is released


·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the key warning light is displayed on the multi-information display on the combination meter assembly, and then press the engine switch.


OK:

The display changes in response to the operation of the engine switch.


Result:
Proceed to
OK
NG (w/ ID Code Box (Immobiliser Code ECU))
NG (w/o ID Code Box (Immobiliser Code ECU))




OK

NG (w/ ID Code Box (Immobiliser Code ECU))

30.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG (w/o ID Code Box (Immobiliser Code ECU))

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

26.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P and the engine switch is off, if any door is opened or closed, the steering is locked.

·

When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 223 2
OK:

The item in the Data List indicates "ON" (the steering is unlocked).



Result:
Proceed to
OK
NG



OK

GO TO STEERING LOCK SYSTEM (UNABLE TO UNLOCK STEERING WHEEL)

NG

27.READ VALUE USING GTS (L CODE CHECK)
27.READ VALUE USING GTS (L CODE CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)*1
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)*2
OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed*1:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


When NG is displayed:*2
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


·

*1: w/ ID Code Box (Immobiliser Code ECU)

·

*2: w/o ID Code Box (Immobiliser Code ECU)


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
HINT:
Reasons for verification failure:
·

The steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.



OK:

The Data List item changes to "OK" when the key is inside the vehicle.



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

29.READ VALUE USING GTS (S CODE CHECK)
28.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one (Refer to the Service Bulletin).


b.

Perform the registration procedures (Refer to the Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly again.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK (S code certification result normal) appears on the screen.



Result:
Proceed to
OK
NG



OK

END

NG

30.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
29.READ VALUE USING GTS (S CODE CHECK)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform the registration procedures (Refer to the Service Bulletin).


c.

Use the Data List to check if L code certification is functioning properly again.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)*1
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)*2
OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed*1:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


When NG is displayed:*2
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


·

*1: w/ ID Code Box (Immobiliser Code ECU)

·

*2: w/o ID Code Box (Immobiliser Code ECU)


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK (L code certification result normal) appears on the screen.



Result:
Proceed to
OK
NG (w/ ID Code Box (Immobiliser Code ECU))
NG (w/o ID Code Box (Immobiliser Code ECU))



OK

END

NG (w/ ID Code Box (Immobiliser Code ECU))

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

NG (w/o ID Code Box (Immobiliser Code ECU))

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

30.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU) with a new one (Refer to the Service Bulletin).


b.

Perform the registration procedures (Refer to the Service Bulletin).


c.

Use the Data List to check if S code certification is functioning properly again.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
S Code Check
50003 125 65
OK:

OK (S code certification result normal) appears on the screen.



Result:
Proceed to
NEXT



NEXT

END