Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2014.09–2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P1603  Engine Stall History  P1605  Rough Idling  


DESCRIPTION

P1603

After starting the engine, this DTC is stored when the engine stops without the engine switch being operated.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1603 After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the engine switch being operated for 0.5 seconds or more (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Thermostat

·

Power supply circuit (purge VSV, air fuel ratio sensor, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

PCV valve and hose

·

Camshaft timing oil control valve assembly

·

Knock control sensor

·

Ignition system

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Charging system

·

A/T system

·

Park/Neutral position switch assembly

·

ECM

·

Wire harness or connector

·

Immobiliser system



P1605

This DTC is stored if the engine speed drops below the set speed.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1605 After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Thermostat

·

Power supply circuit (purge VSV, air fuel ratio sensor, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

PCV valve and hose

·

Camshaft timing oil control valve assembly

·

Knock control sensor

·

Ignition system

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Charging system

·

A/T system

·

Park/Neutral position switch assembly

·

ECM

·

Wire harness or connector



Reference waveforms showing a normal cold engine start


A223608


Reference waveforms showing a normal warm engine start


A223609


Reference values when there is an air leak in the intake system during rough idling


Freeze Frame Data P1605 Rough Idling
Engine
Current P1605: Rough Idling
Time Freeze Frame Data
Item Data1 Data2 Data3 Data4 Data5 Unit
Engine Speed 647 649 586 378 182 rpm
Calculate Load 26.2 26.2 29.1 42.6 58.6 %
Vehicle Load 11.7 11.7 12.1 48.7 61.2 %
MAF 2.87 2.87 2.87 6.23 3.04 gm/sec
Atmosphere Pressure 99 99 99 99 99 kPa
Coolant Temp 86 86 86 86 86 °C
Intake Air 43 43 43 43 43 °C
Battery Voltage 13.515 13.515 13.264 12.892 12.792 V
Throttle Sensor Volt % 14.5 14.5 14.5 16.8 17.2 %
Throttle Sensor #2 Volt % 46.2 46.2 46.2 48.4 49.2 %
Throttle Sensor Position 0.0 0.0 0.0 0.0 0.0 %
Throttle Motor DUTY 14.5 14.5 14.5 17.2 17.2 %
Injector (Port) 2.1 2.1 2.1 2.1 2.1 ms
Injection Volume (Cylinder 1) 0.093 0.093 0.093 0.095 0.095 ml
Fuel Pump/Speed Status ON ON ON ON ON
EVAP (Purge) VSV 13.3 13.3 13.3 13.3 13.3 %
Evap Purge Flow 2.9 2.9 2.9 3.2 3.2 %
Purge Density Learn Value 0.891 0.891 0.891 0.891 0.891
EVAP purge VSV OFF OFF OFF OFF OFF
Target Air-Fuel Ratio 0.998 0.998 0.998 0.998 0.998
AF Lambda B1S1 0.999 0.997 1.001 1.038 1.118
AF Lambda B2S1 0.997 0.994 0.999 1.036 1.112
AFS Voltage B1S1 3.258 3.242 3.284 3.521 3.715 V
AFS Voltage B2S1 3.251 3.306 3.324 3.497 3.689 V
O2S B1S2 0.740 0.740 0.740 0.740 0.740 V
O2S B2S2 0.760 0.760 0.760 0.760 0.760 V
Short FT #1 -1.563 -1.563 -1.563 -1.563 -1.563 %
Long FT #1 6.250 6.250 6.250 6.250 6.250 %
Total FT #1 0.054 0.054 0.054 0.054 0.054
Sort FT #2 -0.782 -0.782 -0.782 -0.782 -0.782 %
Long FT #2 7.031 7.031 7.031 7.031 7.031 %
Total FT #2 0.062 0.062 0.062 0.062 0.062
Fuel System Status #1 CL CL CL CL CL
Fuel System Status #2 CL CL CL CL CL
IGN Advance 22.0 22.0 22.5 23.5 23.5 deg
Knock Feedback Value -1.5 -1.5 -1.5 -1.5 -1.5 CA
Knock Correct Learn Value 17.0 17.0 17.0 17.0 17.0 CA
Starter Signal OFF OFF OFF OFF OFF


CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air-fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air-fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

·

When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. The ECM stores DTC P1605 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1603:

A224366E03
0.219,0.775 1.114,1.107 0.895,0.332 10 While idling or while driving? 1.824,0.778 3.155,1.478 1.332,0.700 10 Did the engine speed decrease slowly or rapidly when engine stall occurred? 0.189,0.599 0.373,0.783 0.184,0.184 10 1: 1.824,0.599 2.007,0.783 0.184,0.184 10 2: 3.925,0.778 4.961,1.295 1.036,0.517 10 Was the air fuel ratio abnormal or normal? 3.925,0.599 4.109,0.783 0.184,0.184 10 3: 5.961,0.75 6.904,0.915 0.943,0.165 10 Intake air leak 5.781,1.758 7.031,1.923 1.250,0.165 10 Sensor malfunction 1.242,5.833 2.492,5.998 1.250,0.165 10 Sensor malfunction 5.748,2.763 7.061,2.928 1.313,0.165 10 Fuel supply problem 1.214,7.822 2.527,7.987 1.313,0.165 10 Fuel supply problem 6.036,3.459 6.746,3.809 0.710,0.350 10 Air volume insufficient 5.953,4.47 6.878,4.802 0.924,0.332 10 Ignition timing incorrect 3.41,4.481 4.492,4.822 1.082,0.341 10 Injection and ignition stoppage 1.337,6.554 2.418,6.895 1.082,0.341 10 Injection and ignition stoppage 3.497,5.48 4.394,5.821 0.897,0.341 10 Load from external parts 1.31,0.134 1.697,0.299 0.387,0.165 10 Idling 0.096,2.544 0.557,2.709 0.461,0.165 10 Driving 2.972,0.134 4.156,0.299 1.184,0.165 10 Decreased Slowly 1.16,2.544 2.400,2.746 1.239,0.202 10 Decreased Rapidly 5.027,0.134 5.692,0.317 0.665,0.184 10 Abnormal 3.832,2.544 4.330,2.709 0.498,0.165 10 Normal

1:
·

If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air fuel ratio, etc.

·

If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.


2:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


3:
·

If the air fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Vehicle State Engine Speed Suspected Area Primary Parts to Inspect Procedure
Idling or decelerating Slowly decreases and engine stalls Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assembly

·

Spark plug


10, 38, 52
Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


5 to 9
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Thermostat


11 to 23
Sensor malfunction (value from sensor too rich) 39 to 51
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


24 to 37
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter sub-assembly

·

Brake booster

·

PCV valve and hose

·

Purge VSV system


53 to 55
Excessive valve overlap
·

Camshaft timing oil control valve assembly


56 to 59
Ignition timing incorrect Does not operate as expected
·

Knock control sensor

·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly


60 to 64
Rapidly decreases and engine stalls Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


65, 66
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/Neutral position switch assembly


67 to 69
Accelerating - Crankshaft position sensor or VVT sensor malfunction Power temporarily cut
·

Check DTCs


1
Mass air flow meter sub-assembly Foreign matter adhesion
·

Mass air flow meter sub-assembly


70 to 73
Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


74, 75
Fuel supply problem Fuel leak, clog
·

Fuel pump control circuit

·

Fuel line


76 to 80

P1605:

A224367E22
0.5,0.573 0.667,0.75 0.167,0.177 10 false 1: 0.5,0.76 1.677,1.688 1.177,0.927 10 false Did the engine speed decrease slowly or rapidly? 2.823,0.573 2.99,0.75 0.167,0.177 10 false 2: 2.823,0.771 3.917,1.583 1.094,0.813 10 false Was the air fuel ratio abnormal or normal? 5.688,0.719 6.635,0.885 0.948,0.167 10 false Intake air leak 5.552,1.729 6.792,1.896 1.24,0.167 10 false Sensor malfunction 5.521,2.719 6.792,2.917 1.271,0.198 10 false Fuel supply problem 4.031,2.063 4.74,2.385 0.708,0.323 10 false Air volume insufficient 3.927,3.052 4.854,3.385 0.927,0.333 10 false Ignition timing incorrect 1.583,2.708 2.677,3.063 1.094,0.354 10 false Injection and ignition stoppage 1.667,3.708 2.594,4.063 0.927,0.354 10 false Load from external parts 1.906,0.875 2.625,1.229 0.719,0.354 10 false Decreased Slowly 0.26,1.844 0.979,2.198 0.719,0.354 10 false Decreased Rapidly 4.302,0.896 4.948,1.063 0.646,0.167 10 false Abnormal 2.771,1.844 3.292,2.01 0.521,0.167 10 false Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assembly

·

Spark plug


10, 38, 52
Air fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


5 to 9
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Thermostat


11 to 23
Sensor malfunction (value from sensor too rich) 39 to 51
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


24 to 37
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter sub-assembly

·

Brake booster

·

PCV valve and hose

·

Purge VSV system


53 to 55
Excessive valve overlap
·

Camshaft timing oil control valve assembly


56 to 59
Ignition timing incorrect Does not operate as expected
·

Knock control sensor

·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly


60 to 64
Rapidly decreases Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


65, 66
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system

·

A/T system

·

Park/Neutral position switch assembly


67 to 69

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
Only DTC P1603 and/or P1605 is output A
DTC and other DTCs P1603 and/or P1605 are output B

HINT:

If any DTCs other than P1603 or P1605 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

OK:

Immobiliser Fuel Cut is OFF.


Result
Result Proceed to
Abnormal A
Normal B



A

3.CHECK ENGINE IMMOBILISER SYSTEM

B

4.READ FREEZE FRAME DATA
3.CHECK ENGINE IMMOBILISER SYSTEM

OK

4.READ FREEZE FRAME DATA

NG

4.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Problem Symptom Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases (and engine stalls) All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are +15% or more*2
·

Air suction


·

Sensor malfunction (value from sensor too lean)


·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are from -15% to +15%
·

Intake air volume insufficient


·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases (and engine stalls) Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage


·

Load from external parts


D
When accelerating or driving at constant speed, engine stalls*4 At least one is OFF - -
·

Sensor malfunction


·

Injection stoppage, ignition stoppage


·

Fuel supply problem


E

A215381E01
0.072,0.032 2.177,0.197 2.105,0.165 10 Rapid Decrease in Engine Speed 2.333,0.377 2.702,0.561 0.369,0.184 10 (rpm) 2.389,0.723 2.665,0.869 0.276,0.147 10 800 2.389,0.928 2.665,1.075 0.276,0.147 10 600 2.389,1.126 2.665,1.272 0.276,0.147 10 400 2.389,1.331 2.665,1.478 0.276,0.147 10 200 2.548,1.529 2.689,1.675 0.142,0.147 10 0 3.038,1.642 3.235,1.798 0.198,0.156 10 #1 3.472,1.642 3.670,1.798 0.198,0.156 10 #2 3.935,1.642 4.132,1.798 0.198,0.156 10 #3 4.153,1.642 4.350,1.798 0.198,0.156 10 #4 4.377,1.642 4.574,1.798 0.198,0.156 10 #5 4.985,1.105 6.058,1.261 1.073,0.156 10 400 rpm or more 1.216,1.019 2.122,1.203 0.906,0.184 10 Engine Speed 2.702,1.944 4.816,2.128 2.114,0.184 10 Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

(a)

In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.

(b)

In the freeze frame data, the engine speed at #5 is 120 rpm or less.



·

*2: When a DTC is stored, feedback compensation increases because the air fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air fuel ratio is determined to be rich.

·

*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.





A

5.CHECK INTAKE SYSTEM

B

38.CHECK IGNITION SYSTEM

C

52.CHECK IGNITION SYSTEM

D

65.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

E

70.CHECK FREEZE FRAME DATA
5.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.




OK

6.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK PURGE VSV
a.
A172615

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.


HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).




OK

7.READ FREEZE FRAME DATA

NG

7.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Stop Light Switch At least 1 of the 5 sets of freeze frame data is ON Air suction from brake booster A
All 5 sets of freeze frame data are OFF - B



A

8.READ VALUE USING INTELLIGENT TESTER (SHORT FT)

B

10.CHECK IGNITION SYSTEM
8.READ VALUE USING INTELLIGENT TESTER (SHORT FT)
a.
A217928E25
0.219,0.573 0.927,0.74 0.708,0.167 10 false Depressed 0.094,0.052 0.906,0.208 0.813,0.156 10 false Brake Pedal 0.313,1.094 0.938,1.25 0.625,0.156 10 false Released 0.302,1.979 0.906,2.135 0.604,0.156 10 false Short FT 2.51,2.229 3.26,2.563 0.75,0.333 10 false Change is 10% or less

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



d.

Idle the engine.


e.

Using the intelligent tester, read the value of Short FT #1 and Short FT #2 in the Data List while depressing the brake pedal.

Standard:

Short FT #1 and Short FT #2 changes by +10% or less.


HINT:

When air leakage from the brake booster is present, the feedback compensation increases because the air fuel ratio becomes lean.




OK

9.PERFORM DRIVE TEST

NG

INSPECT BRAKE BOOSTER ASSEMBLY

9.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Short FT #1, Long FT #1, Short FT #2 and Long FT #2 in the Data List.

Standard:
Data List Condition Specified Condition
Short FT #1 + Long FT #1 The conditions of the vehicle are matched to those present when the problem occurs -15 to +15%
Short FT #2 + Long FT #2 The conditions of the vehicle are matched to those present when the problem occurs -15 to +15%




OK

10.CHECK IGNITION SYSTEM

NG

INSPECT BRAKE BOOSTER ASSEMBLY

10.CHECK IGNITION SYSTEM
a.

Check ignition system.



OK

11.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

11.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter sub-assembly A
AFS Voltage B1S1
AFS Voltage B2S1
3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector


B

HINT:
·

*1: If the mass air flow meter sub-assembly is malfunctioning and incorrectly measures the intake air volume to be less than the actual volume, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is lean, the actual air fuel ratio will become rich and the engine may stall.





A

12.CHECK MASS AIR FLOW METER SUB-ASSEMBLY

B

15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
12.CHECK MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly.


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B



A

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0100).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

14.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Calculate Load in the Data List.

Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle


Result
Result Proceed to
Abnormal A
Normal B



A

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

18.READ FREEZE FRAME DATA
15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A353104E03
0.76,0.083 1.885,0.333 1.125,0.25 10 false Injection Volume 1.313,0.469 1.875,0.677 0.563,0.208 10 false +12.5% 1.323,0.771 1.885,0.979 0.563,0.208 10 false -12.5% 0.552,1.688 3.25,1.948 2.698,0.26 10 false Air Fuel Ratio Sensor Output Voltage 0.646,2.188 1.854,2.406 1.208,0.219 10 false Higher than 3.4 V 0.979,2.594 2.188,2.813 1.208,0.219 10 false Below 3.1 V 0.5,3.427 3.333,3.635 2.833,0.208 10 false Heated Oxygen Sensor Output Voltage 0.615,3.917 1.823,4.135 1.208,0.219 10 false Higher than 0.55 V 1.01,4.292 2.219,4.51 1.208,0.219 10 false Below 0.4 V 3.042,2.375 3.333,2.594 0.292,0.219 10 false OK 2.969,4.115 3.26,4.333 0.292,0.219 10 false OK

Connect the intelligent tester to the DLC3.


b.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


c.

Idle the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and AFS Voltage B2S1.


f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
Tester Display Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.




A

16.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

B

18.READ FREEZE FRAME DATA
16.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR AIR FUEL RATIO SENSOR POWER SOURCE CIRCUIT

17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2237).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

18.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C (18°F) *1 A
Difference in temperature between each item is 10°C (18°F) or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

19.READ FREEZE FRAME DATA

B

21.READ FREEZE FRAME DATA
19.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

A217929E19
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C

HINT:

This step is not directly related to engine stall.




A

20.INSPECT THERMOSTAT

B

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

24.READ FREEZE FRAME DATA
20.INSPECT THERMOSTAT
a.

Inspect the thermostat (See page Engine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION).

Result
Result Proceed to
Abnormal A
Normal B



A

B

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
21.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B

HINT:

*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.




A

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

24.READ FREEZE FRAME DATA
22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

23.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

23.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-79 (THW) - D7-2 (THW) Always Below 1 Ω
D1-78 (ETHW) - D7-1 (E2) Always Below 1 Ω
D1-79 (THW) or D7-2 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

24.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B

HINT:

If the purge VSV is stuck closed, air fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air fuel ratio becomes lean and the engine may stall.




A

25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

B

33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A159587E01
0.26,0.26 0.971,0.421 0.711,0.161 10 VSV is ON 1.978,0.26 2.745,0.421 0.767,0.161 10 VSV is OFF

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.


f.

Operate the purge VSV and check the air flow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
NG A
OK B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

26.INSPECT PURGE VSV

B

33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
26.INSPECT PURGE VSV

OK

27.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)

NG

27.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)
a.
U188263E02
1.333,1.719 2.052,1.917 0.719,0.198 10 false Front View 0.802,0.49 2.24,0.688 1.438,0.198 10 false Purge VSV Connector 0.052,0.052 1.354,0.25 1.302,0.198 10 false Wire Harness Side: 0.854,1.229 1.063,1.406 0.208,0.177 10 false D9

Disconnect the purge VSV connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D50-1 - Body ground Engine switch on (IG) 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PURGE VSV - EFI MAIN RELAY)

28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Check harness and connector.

HINT:
·

Refer to DTC P0443 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0443).

·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

29.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.




NEXT

30.READ VALUE USING INTELLIGENT TESTER (EVAP (PURGE) VSV)
30.READ VALUE USING INTELLIGENT TESTER (EVAP (PURGE) VSV)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine for 15 minutes or more.


d.

Using the intelligent tester, read the value of EVAP (Purge) VSV in the Data List.

Standard:
Data List Specified Condition
EVAP (Purge) VSV Value other than 0% is displayed


Result
Result Proceed to
Abnormal A
Normal B



A

31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

B

31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A159587E01
0.26,0.26 0.971,0.421 0.711,0.161 10 VSV is ON 1.978,0.26 2.745,0.421 0.767,0.161 10 VSV is OFF

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Evap Control.


f.

Operate the purge VSV and check the air flow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result
Result Proceed to
NG A
OK B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

32.CHECK CONNECTOR CONNECTION CONDITION (ECM)

B

32.CHECK CONNECTOR CONNECTION CONDITION (ECM)
a.

Check the ECM connector connection condition.

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

NG

RECONNECT CONNECTOR CORRECTLY

33.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.


e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the intelligent tester.

Standard:
Intelligent Tester Operation Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result:
Result Specified Condition
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 34.





A

34.INSPECT FUEL PUMP

B

35.CHECK FUEL SYSTEM
34.INSPECT FUEL PUMP
a.


OK

NG

35.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinders Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B



A

36.CHECK FUEL SYSTEM

B

36.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is no foreign matter and no signs that fuel pump was stuck A
There is foreign matter or signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

37.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

37.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinders Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).




OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

38.CHECK IGNITION SYSTEM
a.

Check ignition system.



OK

39.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

39.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load 110% or more of the current value of the vehicle*1 Mass air flow meter sub-assembly A
AFS Voltage B1S1
AFS Voltage B2S1
Below 3.3 V*2
·

Air fuel ratio sensor

·

Harness and connector


B
Both freeze frame data items listed above Values are other than above - C

HINT:
·

*1: If the mass air flow meter sub-assembly is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake air surge tank assembly, the freeze frame data will show a high engine load value.

·

*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air fuel ratio is rich, the actual air fuel ratio will become lean and the engine may stall.





A

40.CHECK MASS AIR FLOW METER SUB-ASSEMBLY

B

43.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

46.READ FREEZE FRAME DATA
40.CHECK MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B



A

41.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

41.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0100).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

42.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Calculate Load in the Data List.

Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle




OK

43.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

43.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A353104E03
0.76,0.083 1.885,0.333 1.125,0.25 10 false Injection Volume 1.313,0.469 1.875,0.677 0.563,0.208 10 false +12.5% 1.323,0.771 1.885,0.979 0.563,0.208 10 false -12.5% 0.552,1.688 3.25,1.948 2.698,0.26 10 false Air Fuel Ratio Sensor Output Voltage 0.646,2.188 1.854,2.406 1.208,0.219 10 false Higher than 3.4 V 0.979,2.594 2.188,2.813 1.208,0.219 10 false Below 3.1 V 0.5,3.427 3.333,3.635 2.833,0.208 10 false Heated Oxygen Sensor Output Voltage 0.615,3.917 1.823,4.135 1.208,0.219 10 false Higher than 0.55 V 1.01,4.292 2.219,4.51 1.208,0.219 10 false Below 0.4 V 3.042,2.375 3.333,2.594 0.292,0.219 10 false OK 2.969,4.115 3.26,4.333 0.292,0.219 10 false OK

Connect the intelligent tester to the DLC3.


b.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


c.

Idle the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and AFS Voltage B2S1.


f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
Tester Display Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result
Result Proceed to
Abnormal A
Normal B

HINT:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.




A

44.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

B

46.READ FREEZE FRAME DATA
44.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)
a.

Check the harnesses and connectors, referring to DTC P0031 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0031).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

45.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

REPAIR AIR FUEL RATIO SENSOR POWER SOURCE CIRCUIT

45.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P2237).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

46.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C (18°F)*1 A
Difference in temperature between each item is 10°C (18°F) or more*2 B

HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

47.READ FREEZE FRAME DATA

B

49.READ FREEZE FRAME DATA
47.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

A217929E19
0.467,0.856 2.887,1.519 2.420,0.663 10 Engine Coolant Temperature Increase after Engine Start (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start) 3.423,0.037 3.718,0.234 0.295,0.198 10 (°C) 5.609,2.116 6.223,2.286 0.614,0.170 10 (Minutes) 5.16,1.69 5.316,1.846 0.156,0.156 10 A 4.964,0.779 5.120,0.935 0.156,0.156 10 C 3.891,0.493 4.047,0.649 0.156,0.156 10 B 3.563,2.39 5.573,2.546 2.010,0.156 10 Time Elapsed after Engine Start

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature B
Range C - C

HINT:

This step is not directly related to engine stall.




A

48.INSPECT THERMOSTAT

B

50.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

78.CHECK FUEL SYSTEM
48.INSPECT THERMOSTAT
a.

Inspect the thermostat (See page Engine / Hybrid System>2GR-FE COOLING>THERMOSTAT>INSPECTION).

Result
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.



A

B

50.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
49.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C (248°F) or higher Engine coolant temperature sensor A
Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B

HINT:

*: Use an actual outside temperature estimated from the Initial Intake Air, Ambient Temp for A/C, and (if possible) the weather when the DTC was detected.




A

50.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

81.CLEAR DTC
50.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

51.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

51.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-79 (THW) - D7-2 (THW) Always Below 1 Ω
D1-98 (ETHW) - D7-1 (E2) Always Below 1 Ω
D1-79 (THW) or D7-2 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

52.CHECK IGNITION SYSTEM
a.

Check ignition system.



OK

53.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

53.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle Intake air volume insufficient A
80% or more of the current value of the vehicle B



A

54.CHECK INTAKE SYSTEM

B

56.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
54.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.




OK

55.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE INTAKE SYSTEM

55.CHECK INTAKE SYSTEM
a.

Check the intake system.


Result
Result Proceed to
Abnormal A
Normal B



A

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

60.READ FREEZE FRAME DATA
56.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
a.

Perform the Active Test, referring to DTC P0011 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0011).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.





OK

57.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

57.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0010 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0010).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

58.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

58.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)
a.

Perform the Active Test, referring to DTC P0014 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0014).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.





OK

59.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

59.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0013 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0013).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

60.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

60.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more Less than 3°CA
·

Engine coolant temperature sensor

·

Mass air flow meter sub-assembly

·

Knock control sensor


A
3°CA or more - B
Differs from the current value of the vehicle by less than 10 deg - -



A

61.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

61.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

62.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

62.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-79 (THW) - D7-2 (THW) Always Below 1 Ω
D1-78 (ETHW) - D7-1 (E2) Always Below 1 Ω
D1-79 (THW) or D7-2 (THW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

63.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

63.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter sub-assembly (intake air temperature sensor) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION).

HINT:

If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter sub-assembly (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.




OK

64.READ VALUE USING INTELLIGENT TESTER (IGN ADVANCE AND KNOCK CORRECT LEARN VALUE)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

64.READ VALUE USING INTELLIGENT TESTER (IGN ADVANCE AND KNOCK CORRECT LEARN VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of IGN Advance and Knock Correct Learn Value in the Data List.

Result
Freeze Frame Data Item for DTC P1605 Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10 deg or more Less than 3°CA A
3°CA or more B
Differs from the current value of the vehicle by less than 10 deg -

HINT:

If the results of the checks performed in steps 56 to 64 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.




A

B

END

65.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harness and connectors, referring to Fuel Injector Circuit inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)





OK

66.CHECK IGNITION SYSTEM

NG

REPAIR FUEL INJECTOR ASSEMBLY POWER SOURCE CIRCUIT

66.CHECK IGNITION SYSTEM
a.

Check ignition system.



OK

67.CHECK FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

67.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display does not change from OFF Value displayed for Air Conditioner FB Val does not increase Changes from OFF to ON Power steering system A
Does not change from OFF -
A/C Signal display changes from OFF to ON*1 Value displayed for Air Conditioner FB Val increases Changes from OFF to ON Power steering system
Does not change from OFF A/C system B

HINT:
·

*1: Check not only the ON/OFF state of the air conditioner but also the change in air conditioner load.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the power steering system or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system or A/C system.





A

68.CHECK FREEZE FRAME DATA

B

68.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Electrical Load Signal or Electric Load Feedback Val Electric Load Feedback Val ECT Lock Up Vehicle Speed
Electrical Load Signal display changes from OFF to ON*3, or value displayed for Electric Load Feedback Val increases*3 Value displayed for Electric Load Val changes - - Electrical load signal circuit C
Value displayed for Electric Load Val does not change At least 1 of the 5 sets of freeze frame data is ON Less than 15 km/h (9 mph) A/T system B
15 km/h (9 mph) or more - A
All 5 sets of freeze frame data are OFF - - A
Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - At least 1 of the 5 sets of freeze frame data is ON Less than 15 km/h (9 mph) A/T system B
15 km/h (9 mph) or more - A
All sets of freeze frame data are OFF - - A

HINT:
·

*3: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.

·

Even if the results are normal, the electrical load signal system and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the electrical load system and/or A/T system.





A

69.CHECK FREEZE FRAME DATA

B

C

69.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Shift SW Status (P Range)
Shift SW Status (N Range)
Neutral Position SW Signal
P and N position are both OFF in at least one data set ON when shift lever in D or R Park/Neutral position switch assembly A
OFF when shift lever in D or R A/T system B
All 5 sets of freeze frame data are ON - - C

HINT:

Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system.




A

B

C

70.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter sub-assembly A
Calculate Load does not decrease while Throttle Sensor Position increases - B



A

71.CHECK MASS AIR FLOW METER SUB-ASSEMBLY

B

74.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
71.CHECK MASS AIR FLOW METER SUB-ASSEMBLY
a.

Remove the mass air flow meter sub-assembly (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).


b.

Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.

Result
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B



A

72.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

72.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0100 inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0100).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

73.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

73.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Calculate Load in the Data List.

Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle




OK

74.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

74.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.

Check the harness and connectors, referring to Fuel Injector Circuit inspection procedure (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit).

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)





OK

75.CHECK IGNITION SYSTEM

NG

REPAIR FUEL INJECTOR ASSEMBLY POWER SOURCE CIRCUIT

75.CHECK IGNITION SYSTEM
a.

Check ignition system.



OK

76.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

76.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.


e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the intelligent tester.

Standard:
Intelligent Tester Operation Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result:
Result Specified Condition
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 77.





A

77.INSPECT FUEL PUMP

B

78.CHECK FUEL SYSTEM
77.INSPECT FUEL PUMP
a.


OK

NG

78.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinder Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


Result
Result Proceed to
Abnormal A
Normal B



A

79.CHECK FUEL SYSTEM

B

79.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is no foreign matter and no signs that fuel pump was stuck A
There is foreign matter or signs that fuel pump was stuck B

HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

80.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

80.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test [Control the All Cylinder Fuel Cut].


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures (See page Engine / Hybrid System>2GR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).




OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

81.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.




NEXT

END