When the key is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P or N*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch.
*1: except Manual Transaxle
*2: for Manual Transaxle
When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Engine does not start | Power Source Control:
·
Stop Light Switch1*1 ·
Steering Unlock Switch ·
Power Supply Condition ·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Inside) ·
IG1 Relay Monitor(Outside) ·
IG2 Relay Monitor(Outside) ·
Latch Circuit ·
Shift P Signal*1 ·
Neutral SW/ Clutch SW ·
Starter Request Signal Entry&Start:
·
Immobiliser ·
S Code Check*2 ·
L Code Check ·
Engine Start Request Starting Control:
·
Ignition ·
Starter SW ·
Shift Position P or N*1 |
- |
*1: except Manual Transaxle
*2: w/ Multi-information Display (Dot Display Type)
Refer to "System Diagram".
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.
Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly), ECM or ID code box (immobiliser code ECU) (w/ Multi-information Display (Dot Display Type)), refer to the entry and start system (for Start Function) precaution.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.
After completing repairs, confirm that the problem does not occur.
If the brake pedal is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal to illuminate the stop lights increases.
Measure the battery voltage.
11 to 14 V
It may be possible to tell whether the vehicle battery is discharged by operating the horn.
If the battery voltage is less than 11 V, charge or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, confirm the output of DTCs for all systems.
No DTCs are output.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the problem occurs in certain locations or times of day, the possibility of wave interference is high.
Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver (RF band).
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P (except Manual Transaxle).
With the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) released, check that pressing the engine switch causes the power source mode to change.
| Proceed to |
|---|
| Off → on (ACC) → on (IG) → off |
| Power source mode does not change to on (ACC) and on (IG) |
| Power source mode changes to on (IG) but not to on (ACC) |
| Power source mode changes to on (ACC) but not to on (IG) |
Off → on (ACC) → on (IG) → off
Power source mode does not change to on (ACC) and on (IG)
Power source mode changes to on (IG) but not to on (ACC)
Power source mode changes to on (ACC) but not to on (IG)
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P (except Manual Transaxle).
Depress the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle)
w/ Multi-information Display (Segment Display Type):
Confirm that the entry warning light is illuminated in green, and then press the engine switch and check that the engine cranks.
w/ Multi-information Display (Dot Display Type):
Confirm that the entry warning light is displayed, and then press the engine switch and check that the engine cranks.
Engine cranks.
| Proceed to |
|---|
| OK |
| NG (for 1AD-FTV) |
| NG (for 2AD-FHV) |
| NG (for 2AD-FTV (for DPF)) |
| NG (for 2AD-FTV (for CCo)) |
| NG (for 2AR-FE) |
| NG (for 3ZR-FAE) |
| NG (for 3ZR-FE) |
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV (for DPF))
NG (for 2AD-FTV (for CCo))
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
Move the shift lever to P (except Manual Transaxle).
Press the engine switch with the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
It is determined that the engine immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
| Proceed to |
|---|
| OK |
| NG (w/ Multi-information Display (Dot Display Type)) |
| NG (w/ Multi-information Display (Segment Display Type)) |
OK
NG (w/ Multi-information Display (Dot Display Type))
NG (w/ Multi-information Display (Segment Display Type))
Get into the vehicle while carrying the key, move the shift lever to P (except Manual Transaxle), press the engine switch while depressing the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) and check that the combination meter indicator changes.
If the entry warning light illuminates in green (w/ Multi-information Display (Segment Display Type)) or entry warning light is displayed (w/ Multi-information Display (Dot Display Type)) when the procedure above is performed, the P, N and brake signals*1 or clutch signals*2 can be considered to be normal.
*1: except Manual Transaxle
*2: for Manual Transaxle
The entry warning light illuminates in green (w/ Multi-information Display (Segment Display Type)).
The entry warning light is displayed (w/ Multi-information Display (Dot Display Type)).
| Proceed to |
|---|
| OK |
| NG (except Manual Transaxle) |
| NG (for Manual Transaxle) |
OK
NG (except Manual Transaxle)
NG (for Manual Transaxle)
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Starting Control / Data List.
Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P (except Manual Transaxle), press the engine switch while depressing the brake pedal (except Manual Transaxle) or clutch pedal (for Manual Transaxle) and confirm that the Data List item changes.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter operation request | ON or OFF | ON: Starter operation requested
OFF: Starter operation not requested |
When malfunctioning, the engine will not crank |
| Tester Display |
|---|
| Starter SW |
The Data List item changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST relay (starter relay assembly).
for 1AD-FTV
Click hereEngine / Hybrid System>1AD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
for 2AD-FHV
Click hereEngine / Hybrid System>2AD-FHV STARTING>RELAY>ON-VEHICLE INSPECTION
for 2AD-FTV
Click hereEngine / Hybrid System>2AD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
for 2AR-FE
Click hereEngine / Hybrid System>2AR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
for 3ZR-FAE
Click hereEngine / Hybrid System>3ZR-FAE STARTING>RELAY>ON-VEHICLE INSPECTION
for 3ZR-FE
Click hereEngine / Hybrid System>3ZR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
Move the shift lever to P or N.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - Body ground | 20°C (68°F) | 100 to 150 Ω |
| G82-7 (STA) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect starter assembly.
for 1AD-FTV (w/ Stop And Start System)
Click hereEngine / Hybrid System>1AD-FTV STARTING>STARTER(w/ Stop And Start System)>INSPECTION
for 1AD-FTV (w/o Stop And Start System)
Click hereEngine / Hybrid System>1AD-FTV STARTING>STARTER(w/o Stop And Start System)>INSPECTION
for 2AD-FHV
Click hereEngine / Hybrid System>2AD-FHV STARTING>STARTER>INSPECTION
for 2AD-FTV
Click hereEngine / Hybrid System>2AD-FTV STARTING>STARTER>INSPECTION
for 2AR-FE (for 1.6 kw Type)
Click hereEngine / Hybrid System>2AR-FE STARTING>STARTER(for 1.6 kW Type)>INSPECTION
for 2AR-FE (for 1.7 kw Type)
Click hereEngine / Hybrid System>2AR-FE STARTING>STARTER(for 1.7 kW Type)>INSPECTION
for 3ZR-FAE
Click hereEngine / Hybrid System>3ZR-FAE STARTING>STARTER>INSPECTION
for 3ZR-FE (for 1.0 kw Type)
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTER(for 1.0 kW Type)>INSPECTION
for 3ZR-FE (for 1.3 kw Type)
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTER(for 1.3 kW Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG (for 1AD-FTV (w/ Stop And Start System)) |
| NG (for 1AD-FTV (w/o Stop And Start System) |
| NG (for 2AD-FHV) |
| NG (for 2AD-FTV) |
| NG (for 2AR-FE (for 1.6 kw Type)) |
| NG (for 2AR-FE (for 1.7 kw Type)) |
| NG (for 3ZR-FAE) |
| NG (for 3ZR-FE (for 1.0 kw Type)) |
| NG (for 3ZR-FE (for 1.3 kw Type)) |
OK
NG (for 1AD-FTV (w/ Stop And Start System))
NG (for 1AD-FTV (w/o Stop And Start System)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE (for 1.6 kw Type))
NG (for 2AR-FE (for 1.7 kw Type))
NG (for 3ZR-FAE)
NG (for 3ZR-FE (for 1.0 kw Type))
NG (for 3ZR-FE (for 1.3 kw Type))
Remove the starter assembly from the vehicle to perform an inspection.
Remove the ST relay (starter relay assembly) from the No. 2 engine room relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C5-1 - Body ground | Always | 11 to 14 V |
| 5 - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C6-1 - Body ground | Always | 11 to 14 V |
| 5 - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C4-1 - Body ground | Always | 11 to 14 V |
| 5 - Body ground |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - B6-1 | Always | Below 1 Ω |
| 3 or B6-1 - Body ground | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control and Starting Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | Shift position (P, N) | ON or OFF | ON: Shift lever in P or N
OFF: Shift lever not in P or N |
·
Use this item to determine whether the park/neutral position switch is malfunctioning. ·
When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed. |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Condition of park/neutral position switch | ON or OFF | ON: Shift lever in P or N
OFF: Shift lever not in P or N |
When malfunctioning, the engine will not crank. |
| Tester Display |
|---|
| Shift Position P or N |
The item in the Data List changes according to the shift position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is OFF. ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
The item in the Data List changes when the brake pedal is depressed and released.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A5 connector from the stop light switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-18 (STP1) - A5-1 | Always | Below 1 Ω |
| G82-18 (STP1) or A5-1- Body ground | 10 kΩ or higher |
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Reconnect the A5 connector from the stop light switch assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-18 (STP1) - Body ground | Brake pedal released | 1 V or less |
| Brake pedal depressed | 9 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A5 connector from the stop light switch assembly.
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B36 connector from the park/neutral position switch assembly.
Inspect the park/neutral position switch assembly.
for Park/neutral position switch assembly (for U660F)
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for Park/neutral position switch assembly (for U760E)
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for Park/neutral position switch assembly (for U760F)
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for Park/neutral position switch assembly (for K111)
Click hereDrivetrain>K111 MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for Park/neutral position switch assembly (for K111F)
Click hereDrivetrain>K111F MULTIDRIVE / CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG (for U660F) |
| NG (for U760E) |
| NG (for U760F) |
| NG (for K111) |
| NG (for K111F) |
OK
NG (for U660F)
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
NG (for U760E)
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
NG (for U760F)
Click hereDrivetrain>U760F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
NG (for K111)
NG (for K111F)
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
Disconnect the B36 connector from the park/neutral position switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - B36-4 (B) | Always | Below 1 Ω |
| G82-5 (STAR) or B36-4 (B) - Body ground | Always | 10 kΩ or higher |
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Reconnect the B36 connector from the park/neutral position switch assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - Body ground | Engine switch pressed and held with brake pedal depressed (starter on) → Engine switch released after approximately 1 second elapses (starter off) | 6 V or higher* → 1.5 V or less |
*: When the engine is cranking, the battery voltage may momentarily drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Power Source Control/ Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | State of clutch pedal | ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
·
Use this item to determine whether the clutch position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the condition of the clutch pedal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
Disconnect the A4 or F2 clutch start switch connector
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - F2-2 | Always | Below 1 Ω |
| G82-5 (STAR) or F2-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - A4-2 | Always | Below 1 Ω |
| G82-5 (STAR) or A4-2 - Body ground | Always | 10 kΩ or higher |
| *a | Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Reconnect the A4 or F2 clutch start switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G82-5 (STAR) - Body ground | Engine switch pressed and held with clutch start switch depressed (starter on) → Engine switch released after approximately 1 second elapses (starter off) | 6 V or higher* → 1.5 V or less |
*: When the engine is cranking, the battery voltage may momentarily drop to approximately 6 V.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
The certification ECU (smart key ECU assembly) or the ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
OK (S code certification result normal) appears on the screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the steering unlocks when the engine switch is turned on (ACC).
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser | Engine immobiliser system determined by certification ECU (smart key ECU assembly) | Set or Unset | Set: Engine immobiliser system set (engine start prohibited) (engine switch off)
Unset: Engine immobiliser system unset (engine start permitted) (engine switch on(ACC) or on (IG)) |
The engine cannot be started when Set is displayed.
|
| Tester Display |
|---|
| Immobiliser |
The Data List item changes to "Unset" when the engine switch is turned on (ACC) or on (IG).
| Proceed to |
|---|
| OK |
| NG (w/ Multi-information Display (Dot Display Type)) |
| NG (w/ Multi-information Display (Segment Display Type)) |
OK
NG (w/ Multi-information Display (Dot Display Type))
NG (w/ Multi-information Display (Segment Display Type))
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Request Signal | Engine start request signal status | ON or OFF | except Manual Transaxle
ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held OFF: After approx. 1 sec. has elapsed, the engine switch is released for Manual Transaxle
ON: With the clutch pedal depressed, the engine switch is pressed and held OFF: After approx. 1 sec. has elapsed, the engine switch is released |
·
When the engine cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time. |
| Tester Display |
|---|
| Starter Request Signal |
w/ Multi-information Display (Segment Display Type):
Check that the entry warning light on the combination meter assembly illuminates in green, and then press the engine switch.
w/ Multi-information Display (Dot Display Type):
Check that the entry warning is displayed on the multi-information display on the combination meter assembly, and then press the engine switch.
The display changes in response to the operation of the engine switch.
| Proceed to |
|---|
| OK |
| NG (w/ Multi-information Display (Dot Display Type)) |
| NG (w/ Multi-information Display (Segment Display Type)) |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG (w/ Multi-information Display (Dot Display Type))
NG (w/ Multi-information Display (Segment Display Type))
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly | ON or OFF | ON: Steering unlocked
OFF: Steering locked |
·
When the shift lever is in P and the engine switch is off, if any door is opened or closed, the steering is locked. ·
When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. |
| Tester Display |
|---|
| Steering Unlock Switch |
The item in the Data List indicates "ON" (the steering is unlocked).
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>Unable to Unlock Steering Wheel (Engine cannot Start)
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)*1
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)*2 |
OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed*1:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). When NG is displayed:*2 ·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
*1: w/ Multi-information Display (Dot Display Type)
*2: w/ Multi-information Display (Segment Display Type)
| Tester Display |
|---|
| L Code Check |
The steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
The Data List item changes to "OK" when the key is inside the vehicle.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one (Refer to the Service Bulletin).
Perform the registration procedures (Refer to the Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
OK (S code certification result normal) appears on the screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator assembly) with a new one.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY
Perform the registration procedures (Refer to the Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)*1
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly)*2 |
OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed*1:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). When NG is displayed:*2 ·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
*1: w/ Multi-information Display (Dot Display Type)
*2: w/ Multi-information Display (Segment Display Type)
| Tester Display |
|---|
| L Code Check |
OK (L code certification result normal) appears on the screen.
| Proceed to |
|---|
| OK |
| NG (w/ Multi-information Display (Dot Display Type)) |
| NG (w/ Multi-information Display (Segment Display Type)) |
OK
NG (w/ Multi-information Display (Dot Display Type))
NG (w/ Multi-information Display (Segment Display Type))
Replace the ID code box (immobiliser code ECU) with a new one (Refer to the Service Bulletin).
Perform the registration procedures (Refer to the Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When NG is displayed:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| S Code Check |
OK (S code certification result normal) appears on the screen.
| Proceed to |
|---|
| NEXT |
NEXT