Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P1604  Startability Malfunction  


DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1604 Either condition is met:
·

The engine speed is below 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below) (1 trip detection logic).

·

After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds (1 trip detection logic).


·

Immobiliser system

·

Engine assembly (excess friction, compression loss)

·

Starter assembly

·

Crankshaft position sensor

·

Camshaft position sensor

·

Engine coolant temperature sensor

·

Fuel pump

·

Fuel pump control system

·

Fuel pipes

·

Fuel injector

·

Throttle body assembly

·

Pressure regulator

·

Battery

·

Drive plate

·

Spark plug

·

Ignition coil circuit

·

Intake system

·

Camshaft timing oil control valve

·

Mass air flow meter

·

Air fuel ratio sensor

·

Valve timing

·

Fuel

·

Purge VSV

·

Intake valve

·

Exhaust valve

·

ECM



A220316E04
0.314,1.64 1.192,1.824 0.878,0.184 10 Starting Time 1.276,0.37 1.960,0.554 0.684,0.184 10 (Seconds) 3.844,1.136 5.000,1.486 1.156,0.350 10 Region Indicating Malfunction 6.401,2.662 6.682,2.859 0.281,0.198 10 (°C) 1.43,2.26 1.553,2.437 0.123,0.177 10 2 1.883,2.78 2.122,2.936 0.239,0.156 10 -30 3.499,2.78 3.696,2.950 0.198,0.170 10 20 5.189,2.78 5.401,2.964 0.211,0.184 10 80 6.362,2.849 6.698,3.046 0.336,0.198 10 (°F) 1.849,2.967 2.181,3.123 0.332,0.156 10 (-22) 3.459,2.967 3.731,3.137 0.272,0.170 10 (68) 5.096,2.967 5.456,3.150 0.360,0.184 10 (176) 3.518,3.317 5.368,3.500 1.850,0.184 10 Engine Coolant Temperature

Reference waveforms showing a normal cold engine start


A223608


Reference waveforms showing a normal warm engine start


A223609


Reference waveforms showing an engine stop after normal idling


A223610


Reference values when there is an air leak in the intake system during starting difficulty


Freeze Frame Data P1604 Startability Malfunction
Engine
Current P1604: Startability Malfunction
Time Freeze Frame Data
Item Data1 Data2 Data3 Data4 Data5 Unit
Engine Speed 1489 986 345 186 124 rpm
Calculate Load 36.2 28.2 31.4 92.4 94.6 %
Vehicle Load 7.9 7.9 9.2 7.2 6.0 %
MAF 10.12 5.04 2.79 0.81 0.68 gm/sec
Atmosphere Pressure -0 -0 -0 -0 -0 kPa
Coolant Temp 86 86 86 86 86 °C
Intake Air 40 40 40 40 40 °C
Battery Voltage 13.222 13.300 12.109 11.972 11.854 V
Throttle Sensor Volt % 16.5 16.5 16.0 15.6 15.6 %
Throttl Sensor #2 Volt % 48.2 48.2 47.8 47.2 47.2 %
Throttle Sensor Position 0.0 0.0 0.0 0.0 0.0 %
Throttle Motor DUTY 16.5 16.5 16.0 15.6 15.6 %
Injector (Port) 3628 2620 2744 2744 2744 μs
Injection Volum (Cylinder 1) 3.062 0.226 0.226 0.226 0.226 ml
Fuel Pump/Speed Status ON ON ON ON ON
EVAP (Purge) VSV 0.0 0.0 0.0 0.0 0.0 %
Evap Purge Flow 0.0 0.0 0.0 0.0 0.0 %
Purge Density Learn Value 0.000 0.000 0.000 0.000 0.000
EVAP purge VSV OFF OFF OFF OFF OFF
Purge Cut VSV Duty 0.0 0.0 0.0 0.0 0.0 %
Target Air-Fuel Ratio 0.998 0.998 0.998 0.998 0.998
AF Lambda B1S1 0.999 0.999 0.999 0.999 0.999
AFS Voltage B1S1 3.258 3.258 3.258 3.258 3.258 V
O2S B1S2 0.000 0.000 0.000 0.000 0.000 V
Short FT #1 0.000 0.000 0.000 0.000 0.000 %
Long FT #1 8.782 4.354 -2.665 -2.665 -2.665 %
Total FT #1 0.058 0.058 0.058 0.058 0.058
Fuel System Status #1 OL OL OL OL OL
IGN Advance 0.0 10.5 16.5 18.0 18.0 deg
Knock Feedback Value -1.5 -1.5 -1.5 -1.5 -1.5 deg(CA)
Knock Correct Learn Value 17.0 17.0 17.0 17.0 17.0 deg(CA)
Starter Signal OFF OFF OFF OFF OFF


CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

As DTCs may be stored when an Active Test or learning is performed, make sure to clear the DTCs before returning the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.

·

Read freeze frame data using the GTS. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.

·

If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.

·

If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.



Malfunction Recurrence and Inspection Areas


a.

Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

i.

The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

HINT:

One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.


·

If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.

·

If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

·

If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or an ECM may be malfunctioning.

A215383E03
0.133,0.091 4.289,0.274 4.156,0.184 10 When the engine speed for all 5 sets of freeze frame data is 0 rpm: 0.306,0.959 1.573,1.476 1.267,0.517 10 Was the minimum battery voltage 5 V or higher? 2.267,1.08 3.479,1.625 1.211,0.545 10 Was the minimum battery voltage 6 V or higher? 4.061,1.071 5.244,1.450 1.184,0.378 10 Did the battery voltage fluctuate? 5.674,1.033 7.084,1.397 1.410,0.364 10 Inspect the crankshaft position sensor 0.866,3.073 2.161,3.423 1.295,0.350 10 Recharge or replace the battery 2.976,2.933 4.178,3.297 1.202,0.364 10 Inspect the engine assembly 5.209,2.942 6.671,3.283 1.461,0.341 10 Inspect the starter assembly 0.825,4.746 1.166,4.898 0.341,0.151 10 YES 0.825,5.223 1.082,5.388 0.258,0.165 10 NO 2.258,0.912 2.423,1.077 0.165,0.165 10 1. 4.07,0.895 4.235,1.060 0.165,0.165 10 2.



ii.

All engine speeds recorded in the freeze frame data are between 100 and 250 rpm (the engine cranks but there is no combustion).

HINT:

If the engine speed is between 100 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


·

Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.

A215384E02
0.082,0.086 2.821,0.270 2.739,0.184 10 Engine speed is between 100 and 250 rpm: 0.39,0.913 1.851,1.457 1.461,0.545 10 Has an ignition system DTC (IGF, NE, VVT, etc.) been output? 2.94,1.053 4.290,1.403 1.350,0.350 10 Is the engine coolant temperature normal? 2.94,0.885 3.096,1.041 0.156,0.156 10 1. 5.294,1.025 6.755,1.236 1.461,0.211 10 Inspect the fuel system 1.483,2.622 3.139,3.139 1.656,0.517 10 Repair the malfunctioning areas indicated by the output DTCs 5.364,2.636 6.631,3.181 1.267,0.545 10 Replace the engine coolant temperature sensor 0.922,4.471 1.245,4.627 0.323,0.156 10 YES 0.922,5.06 1.189,5.216 0.267,0.156 10 NO



iii.

The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

HINT:

If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.


·

Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.

·

If Long FT is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

·

If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.

A396202E03
0.156,0.135 2.313,0.313 2.156,0.177 10 false Engine speed is 250 rpm or higher: 0.26,0.969 0.448,1.146 0.188,0.177 10 false 1. 0.26,1.156 1.635,1.594 1.375,0.438 10 false Was "Coolant Temp" normal? 2.219,0.979 2.385,1.177 0.167,0.198 10 false 2. 2.208,1.146 3.406,1.729 1.198,0.583 10 false Was "Long FT" normal (within +/- 15%)? 4.115,0.958 4.427,1.156 0.313,0.198 10 false 3. 4.104,1.146 5.208,1.698 1.104,0.552 10 false Was the engine cranking speed too high? 5.781,0.958 7.052,1.396 1.271,0.438 10 false Inspect the engine assembly 0.833,2.854 2.042,3.396 1.208,0.542 10 false Replace the engine coolant temperature sensor 2.979,2.833 4.573,3.469 1.594,0.635 10 false Inspect the fuel injectors for port injection and fuel pump 5.156,2.844 6.792,3.219 1.635,0.375 10 false Inspect the fuel system and intake system 0.833,4.74 1.292,4.938 0.458,0.198 10 false YES 0.854,5.219 1.167,5.417 0.313,0.198 10 false NO




b.

When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem symptoms" and "Systems to inspect")

i.

Problem symptoms

1.

The engine does not crank.

HINT:

The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.


2.

The engine cranking speed is abnormal.

HINT:

If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.


3.

There is no initial combustion.

HINT:

If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.


4.

The engine stalls after starter turnoff.

HINT:

If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.


5.

The initial combustion and starter turnoff occur late.

HINT:

If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).


HINT:

Causes of fuel system malfunctions according to conditions present at the time of the malfunction.

·

When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.

·

When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.

·

When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.





ii.

Systems to inspect.

1.

Intake system

2.

Ignition system

3.

Fuel system





INSPECTION FLOW


a.

Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

Freeze Frame Data Item Result Suspected Area Procedure
Engine Speed 0 rpm (no engine cranking at all)
·

Battery fully depleted

·

Engine assembly (excess friction)

·

Starter assembly

·

Immobiliser system

·

Crankshaft position sensor

·

ECM


4 to 9
100 to 250 rpm (engine cranks but no initial combustion*1)
·

Fuel pump control system

·

Engine coolant temperature sensor

·

Fuel injection system


10 to 14
250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
·

Engine assembly (compression loss)

·

Fuel injection system

·

Fuel pump control system


15 to 23

HINT:
·

*1: First combustion after cranking begins.

·

*2: Condition when engine speed increases and starter can be turned off.




b.

When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

i.

Problem symptoms

Problem Symptom Suspected Area Suspected Component Procedure
The engine does not crank Battery malfunction
·

Battery fully depleted


26 to 31
Starting system
·

Starter (includes pinion gear wear or tooth damage)

·

Starting system


Immobiliser system
·

Immobiliser system


Engine assembly
·

Engine assembly (excess friction)

·

Drive plate wear or tooth damage


Cranking speed too low Battery malfunction
·

Battery fully depleted


32 to 34
Starting system
·

Starter assembly


Engine assembly
·

Engine assembly (excess friction)


Cranking speed too high Engine assembly
·

Engine assembly (compression loss)


There is no initial combustion Fuel supply problem
·

Maintenance of fuel pressure by pressure regulator

·

Fuel injector leak

·

Fuel leak from fuel line

·

Fuel pump control system

·

Fuel pump


35 to 50
Ignition system malfunction
·

Spark plug

·

Crankshaft position sensor

·

Ignition coil


Engine stalls after starter turnoff Air suction
·

Intake system connections


51 to 56
Deposits in throttle body assembly
·

Throttle body assembly


VVT valve does not return properly
·

Camshaft timing oil control valve

·

VVT system


Mass air flow meter malfunction
·

Mass air flow meter


The initial combustion and starter turnoff occur late Engine coolant temperature sensor malfunction
·

Engine coolant temperature sensor


57 to 71
Mass air flow meter malfunction
·

Mass air flow meter


Abnormal air fuel ratio learning value
·

Air fuel ratio sensor


Deviation from fuel injection characteristics
·

Fuel injector for port injection


Wet-fouled or dry-fouled spark plug
·

Spark plug


Lack of fuel pressure
·

Pressure regulator

·

Fuel pump

·

Fuel pump control system




ii.

Systems to inspect

Troubleshooting by System Suspected Area Suspected Component Procedure
Fuel system troubleshooting A Abnormal air fuel ratio learning value
·

Fuel injector


87 to 94
95 to 102
Rough idling
·

Crankshaft position sensor


Abnormal fuel pressure
·

Fuel

·

Fuel leak from fuel line

·

Fuel pump

·

Pressure regulator


Fuel system troubleshooting B Abnormal concentration of HC in surge tank
·

Purge VSV system

·

Fuel injector


103 to 105
Fuel system troubleshooting C Injection signal system malfunction
·

Fuel injector

·

Crankshaft position sensor

·

Camshaft position sensor

·

ECM


73 to 77
Intake system troubleshooting Difference between ISC target value and opening angle when idling
·

Engine assembly (compression loss)

·

Valve timing

·

Engine coolant temperature sensor

·

ECM


84 to 86
106 to 108
Ignition system troubleshooting Camshaft and/or crankshaft position sensor signal malfunction
·

Crankshaft position sensor system (including sensor installation)

·

Camshaft position sensor system (including sensor installation)

·

ECM


78 to 83
109 to 114




PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA (IN ADDITION TO DTC P1604)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.
A317524E25
0.375,1.125 2.063,1.323 1.688,0.198 10 false 0.5 seconds 1.302,1.135 2.99,1.333 1.688,0.198 10 false 0.5 seconds 2.26,1.135 3.427,1.375 1.167,0.24 10 false 0.5 seconds 2.344,0.25 3.427,0.479 1.083,0.229 10 false DTC is stored 0.396,2.792 3.271,3.063 2.875,0.271 10 false Freeze frame data recorded point 0.219,2.479 0.375,2.677 0.156,0.198 10 false 1 1.167,2.479 1.323,2.677 0.156,0.198 10 false 2 2.135,2.479 2.292,2.677 0.156,0.198 10 false 3 2.729,2.646 2.885,2.844 0.156,0.198 10 false 4 3.073,2.5 3.229,2.698 0.156,0.198 10 false 5

Read the DTCs and record the Freeze Frame Data.

HINT:
·

This freeze frame data shows the actual engine conditions when engine starting trouble occurred.

·

When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.

·

The fourth set of freeze frame data is the data recorded when the DTC is stored.



Result
Result Proceed to
Only DTC P1604 is output A
DTCs other than P1604 are output B



A

2.CHECK ENGINE IMMOBILISER SYSTEM

B

2.CHECK ENGINE IMMOBILISER SYSTEM
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Immobiliser Fuel Cut.


e.

Read the value displayed on the GTS.

OK:

Immobiliser Fuel Cut is OFF


HINT:

If the engine is cranked immediately after reconnecting the battery cable (key verification for immobiliser system not completed), the engine cannot be started. Key verification needs to wait for several seconds after turning the engine switch on (IG).




OK

3.CHECK MALFUNCTION CONDITION

NG

3.CHECK MALFUNCTION CONDITION
a.

Confirm the problem symptoms.

Result
Result Proceed to
Freeze frame data exists, but the problem symptoms cannot be reproduced and the malfunction conditions are unknown A
The problem symptoms can be reproduced, or the malfunction conditions are known B



A

4.READ FREEZE FRAME DATA

B

25.CHECK MALFUNCTION CONDITION
4.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result:
Freeze Frame Data Item for DTC P1604 Suspected Area Proceed to
Engine Speed Battery Voltage
All 0 rpm (no engine cranking at all) Minimum voltage is less than 5 V Battery fully depleted A
Minimum voltage is 5 V or higher
·

Starter malfunction

·

Crankshaft position sensor system

·

Excess engine friction

·

Immobiliser system

·

ECM


B
100 to 250 rpm (engine cranks but no initial combustion) -
·

Fuel pump control system

·

Ignition system

·

Engine coolant temperature sensor

·

Immobiliser system

·

Fuel injection system


C
250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late) -
·

Engine assembly

·

Fuel injection system

·

Fuel pump control system


D


HINT:

When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the Freeze Frame Data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.

*1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.

*2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.

·

Immobiliser Fuel Cut

·

Engine Speed (Starter OFF)

·

Shift SW Status (R, D Range)





A

CHARGE OR REPLACE BATTERY

B

5.READ FREEZE FRAME DATA

C

10.READ FREEZE FRAME DATA

D

15.READ FREEZE FRAME DATA

E

51.INSPECT MASS AIR FLOW METER
5.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result:
Freeze Frame Data Item for DTC P1604 Result Suspected Area Proceed to
Battery Voltage Minimum voltage is 6 V or higher and voltage does not fluctuate*1 Starter system A
Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
·

Crankshaft position sensor system

·

ECM


B
Minimum voltage is 5 to 6 V*4
·

Excess engine friction

·

Battery fully depleted


C


HINT:
·
A226745E03
0.948,0.542 1.063,0.698 0.115,0.156 10 false 1 1.448,0.542 1.563,0.698 0.115,0.156 10 false 2 1.99,0.552 2.104,0.708 0.115,0.156 10 false 3 2.49,0.573 2.604,0.729 0.115,0.156 10 false 4 3,0.583 3.115,0.74 0.115,0.156 10 false 5 0.938,2.177 1.052,2.333 0.115,0.156 10 false 1 1.438,2.156 1.552,2.313 0.115,0.156 10 false 2 1.979,2.156 2.094,2.313 0.115,0.156 10 false 3 2.49,2.146 2.604,2.302 0.115,0.156 10 false 4 3,2.156 3.115,2.313 0.115,0.156 10 false 5 0.927,0.125 2.188,0.438 1.26,0.313 10 false Freeze Frame Data 0.865,1.344 2.125,1.656 1.26,0.313 10 false Freeze Frame Data 0.135,0.25 0.76,1.219 0.625,0.969 10 false Voltage does not Fluctuate 0.104,2.031 0.781,2.635 0.677,0.604 10 false Voltage Fluctuates

*1: The 5 sets of freeze frame data show approximately the same battery voltage.

·

*2: The 5 sets of freeze frame data show different battery voltages.

·

*3: If the voltage fluctuates, it can be determined that cranking is being performed normally. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.

·

*4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.





A

B

6.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION

C

CHECK AND REPAIR ENGINE OR BATTERY

6.CHECK CRANKSHAFT POSITION SENSOR INSTALLATION
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.



OK

7.CHECK CRANKSHAFT POSITION SENSOR

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

7.CHECK CRANKSHAFT POSITION SENSOR
a.

Disconnect the crankshaft position sensor connector.


b.

Check for oil on the connector terminals.

OK:

No oil on the terminals.




OK

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D54-1 - D2-122 (NE+) Always Below 1 Ω
D54-2 - D2-121 (NE-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D54-1 or D2-122 (NE+) - Body ground Always 10 kΩ or higher
D54-2 or D2-121 (NE-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

9.CHECK CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

10.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result:
Freeze Frame Data Item for DTC P1604 Suspected Area Proceed to
Coolant Temp Coolant Temp Fuel Pump/Speed Status
Difference between Coolant Temp, and Intake Air is 10°C (18°F) or more*1 Coolant Temp is 125°C (257°F) or more - Engine coolant temperature sensor A
Other than above All 5 sets of freeze frame data are ON - B
At least 1 of the 5 sets of freeze frame data is OFF Fuel pump control system C
Difference between Coolant Temp, and Intake Air is less than 10°C (18°F)*2 - At least 1 of the 5 sets of freeze frame data is OFF Fuel pump control system C
All 5 sets of freeze frame data are ON - B


HINT:
·

*1: A long time had not elapsed after stopping the engine.

·

*2: A long time had elapsed after stopping the engine.





A

B

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

C

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Disconnect the fuel pump connector.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


f.
U188460E02
0.25,0.198 2.604,0.531 2.354,0.333 10 false Front view of wire harness connector: (to Fuel Pump) 0.667,2.063 0.969,2.24 0.302,0.177 10 false M17

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M17-4 - Body ground Active Test is being performed 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

12.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)

NG

12.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
a.

Disconnect the fuel injector connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D22-1 - Ground Engine switch on (IG) 11 to 14 V
D23-1 - Ground Engine switch on (IG) 11 to 14 V
D24-1 - Ground Engine switch on (IG) 11 to 14 V
D25-1 - Ground Engine switch on (IG) 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - IG2 RELAY)

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.





A

REPAIR OR REPLACE FUEL LINE

B

14.CHECK FUEL SYSTEM
14.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B



A

REPAIR OR REPLACE FUEL SYSTEM

B

24.PERFORM SIMULATION TEST
15.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result:
Freeze Frame Data Item for DTC P1604 Suspected Area Proceed to
Coolant Temp Coolant Temp Long FT Engine Speed
Difference between Coolant Temp, and Intake Air is 10°C (18°F) or more Coolant Temp is 125°C (257°F) or more - - Engine coolant temperature sensor A
Other than above -15% or less, or +15% or more -
·

Fuel pump control system

·

Fuel injector


B
-15 to +15% Minimum speed is 300 rpm or more* Engine assembly C
Minimum speed is below 300 rpm
·

Fuel system

·

Intake air system


D
Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C (18°F) - -15% or less, or +15% or more -
·

Fuel pump control system

·

Fuel injector


B
-15 to +15% Minimum speed is 300 rpm or more* Engine assembly C
Minimum speed is below 300 rpm
·

Fuel system

·

Intake air system


D


HINT:

*: Compression loss may have occurred in the engine assembly.




A

B

16.INSPECT FUEL INJECTOR

C

CHECK AND REPAIR ENGINE ASSEMBLY

D

18.READ FREEZE FRAME DATA
16.INSPECT FUEL INJECTOR
a.

Check that no carbon is stuck to the fuel injector.

OK:

No carbon present.




OK

17.CHECK FUEL SYSTEM

NG

17.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter, and inside the fuel tank), and for signs that the fuel pump was stuck.

Result
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B



A

REPAIR OR REPLACE FUEL SYSTEM

B

24.PERFORM SIMULATION TEST
18.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).

Result:
Freeze Frame Data Item for DTC P1604 Result Suspected Area Proceed to
Coolant Temp Engine coolant temperature is 40°C (104°F) or less*1 Pressure regulator A
Engine coolant temperature is 40 to 90°C (104 to 194°F)*2 Fuel injector B
Engine coolant temperature is 90°C (194°F) or more*3 Pressure regulator A


HINT:

*1: If the engine coolant temperature is 40°C (104°F) or less (after stopping the engine and the vehicle is not driven for a long period of time), the pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*2: If the engine coolant temperature is 40 to 90°C (104 to 194°F) (15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector.

*3: If the engine coolant temperature is 90°C (194°F) or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.




A

19.CHECK FUEL PRESSURE

B

20.CHECK FUEL INJECTOR
19.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Standard:

147 kPa (1.5 kgf/cm2, 21 psi) or higher (5 minutes after stopping the engine)


HINT:

If the engine cannot be started, read the values after cranking the engine.


Result
Result Proceed to
NG A
OK B



A

REPLACE PRESSURE REGULATOR

B

24.PERFORM SIMULATION TEST
20.CHECK FUEL INJECTOR
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result:
Result Proceed to
4000 ppm or higher A
Less than 4000 ppm B


HINT:

If the concentration is 4000 ppm or higher, a fuel injector may have a sealing problem.




A

21.CHECK FUEL INJECTOR

B

22.CHECK THROTTLE BODY ASSEMBLY
21.CHECK FUEL INJECTOR
a.

Inspect the fuel injectors (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>INSPECTION).

Result:
Result Proceed to
NG A
OK B




A

B

22.CHECK THROTTLE BODY ASSEMBLY
22.CHECK THROTTLE BODY ASSEMBLY
a.

Check if carbon is in the air flow passage.

Result:
Result Proceed to
Carbon in passage A
No carbon present B




A

CLEAN OR REPLACE THROTTLE BODY ASSEMBLY

B

23.CHECK INTAKE SYSTEM
23.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leak.

OK:

No leaks in intake system.




OK

24.PERFORM SIMULATION TEST

NG

REPAIR OR REPLACE INTAKE SYSTEM

24.PERFORM SIMULATION TEST
a.

Check if the engine can be started.

Result:
Result Proceed to
Engine can be started A
Engine cannot be started B




A

END

B

25.CHECK MALFUNCTION CONDITION
25.CHECK MALFUNCTION CONDITION
a.

Confirm the problem symptoms.

HINT:

The problem symptoms below can be determined by reading the freeze frame data.


Result:
Problem Symptom Suspected Area Proceed to
The engine does not crank
·

Battery fully depleted

·

Starter (includes pinion gear wear or teeth damage)

·

Starter system

·

Engine assembly (excess friction)

·

Drive plate wear or teeth damage


A
Abnormal cranking speed
·

Battery fully depleted

·

Starter

·

Engine assembly (excess friction, compression loss)


B
There is no initial combustion (combustion does not occur even once)*1
·

Fuel pressure of pressure regulator maintained

·

Fuel injector leak

·

Fuel leak from fuel line

·

Fuel pump control system

·

Fuel pump

·

Spark plug

·

Crankshaft position sensor system

·

Ignition coil system


C
The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*2
·

Intake system connections

·

Throttle body assembly

·

Camshaft timing oil control valve

·

Mass air flow meter system


D
The initial combustion and starter turnoff occur late*3
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Fuel injector

·

Spark plug

·

Pressure regulator

·

Fuel pump

·

Fuel pump control system


E


HINT:
·

If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter may be malfunctioning.

·

*1: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.

·

*2: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve may have a problem returning.

·

*3: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).





A

26.PERFORM SIMULATION TEST

B

32.PERFORM SIMULATION TEST

C

35.CHECK FUEL INJECTOR

D

51.INSPECT MASS AIR FLOW METER

E

57.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
26.PERFORM SIMULATION TEST
a.

When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

Result:
Problem Symptom Suspected Area Proceed to
A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely*
·

Battery

·

Excess engine friction

·

Starter


A
A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely
·

Drive plate

·

Starter


B
A noise indicating that the starter pinion gear is extending is not heard
·

Battery

·

Starter

·

Starter system


C


HINT:

*: The battery may be fully depleted or there may be excess engine friction.




A

27.INSPECT BATTERY

B

29.CHECK STARTER ASSEMBLY

C

30.INSPECT BATTERY
27.INSPECT BATTERY

OK

28.CHECK ENGINE ASSEMBLY

NG

CHARGE OR REPLACE BATTERY

28.CHECK ENGINE ASSEMBLY
a.

Check that the crankshaft rotates smoothly when rotating it by hand.

OK:

Crankshaft rotates smoothly.


HINT:

Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.




OK

INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE ENGINE ASSEMBLY

29.CHECK STARTER ASSEMBLY

b.

Check for starter pinion gear wear and damage.

Standard:

There is no wear or damage.



c.

Install the starter assembly.



OK

NG

REPLACE STARTER ASSEMBLY

30.INSPECT BATTERY

OK

31.INSPECT STARTER ASSEMBLY

NG

CHARGE OR REPLACE BATTERY

31.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly for 1.6 kW type (See page Engine / Hybrid System>2AZ-FE STARTING>STARTER(for 1.6 kW Type)>INSPECTION) or 1.7 kW type (See page Engine / Hybrid System>2AZ-FE STARTING>STARTER(for 1.7 kW Type)>INSPECTION).

Result:
Problem Symptom Proceed to
OK A
NG B




A

B

REPLACE STARTER ASSEMBLY

32.PERFORM SIMULATION TEST
a.

Check the cranking speed.

Result:
Problem Symptom Suspected Area Proceed to
Cranking speed is slow (100 rpm or less)
·

Battery

·

Starter assembly

·

Excess engine friction


A
Cranking speed is fast (300 rpm or more)* Engine compression loss B


HINT:

*: If the cranking speed is fast, there may be compression loss.




A

33.INSPECT BATTERY

B

CHECK AND REPAIR ENGINE ASSEMBLY

33.INSPECT BATTERY

OK

34.CHECK ENGINE ASSEMBLY

NG

CHARGE OR REPLACE BATTERY

34.CHECK ENGINE ASSEMBLY
a.

Check that the crankshaft rotates smoothly when rotating it by hand.

OK:

Crankshaft rotates smoothly.


HINT:

Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.




OK

INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE ENGINE ASSEMBLY

35.CHECK FUEL INJECTOR
a.

Using a sound scope or screwdriver, check for an fuel injector operating noise while cranking the engine.

OK:

Fuel injector operating noise is heard.




OK

36.CHECK FUEL PRESSURE

NG

48.READ VALUE USING GTS (ENGINE SPEED)
36.CHECK FUEL PRESSURE

OK

37.CHECK SPARK PLUG AND SPARK

NG

46.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
37.CHECK SPARK PLUG AND SPARK

OK

38.CONFIRM VEHICLE CONDITION

NG

41.CHECK SPARK PLUG
38.CONFIRM VEHICLE CONDITION
a.

Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

Result:
Problem Symptom Suspected Area Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1 Pressure regulator is stuck open A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2 Fuel injector leak B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3 Failure to maintain fuel pressure by pressure regulator A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs - C*4


HINT:

*1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*2: Fuel may be leaking from a fuel injector.

*3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*4: From step 72, perform fuel system troubleshooting C (steps 73 to 77).




A

39.CHECK FUEL PRESSURE

B

40.CHECK FUEL INJECTOR

C

72.CHECK MALFUNCTION CONDITION
39.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Result:
Result Proceed to
Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine) A
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine) B*


HINT:
·

If the engine cannot be started, check the fuel pressure after cranking the engine.

·

*: From step 72, perform fuel system troubleshooting C (steps 73 to 77).





A

REPLACE PRESSURE REGULATOR

B

72.CHECK MALFUNCTION CONDITION
40.CHECK FUEL INJECTOR
a.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result:
Result Proceed to
4000 ppm or higher A
Less than 4000 ppm B*


HINT:
·

If the concentration is 4000 ppm or higher, a fuel injector may have a sealing problem.

·

*: From step 72, perform fuel system troubleshooting C (steps 73 to 77).





A

B

72.CHECK MALFUNCTION CONDITION
41.CHECK SPARK PLUG

HINT:

Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.



OK

42.READ VALUE USING GTS (ENGINE SPEED)

NG

42.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


e.

Start the engine.


f.

While running the engine, read the Engine Speed value.

Standard:

A value that matches the actual engine speed is constantly output.


HINT:
·

Check the engine speed using a line graph.

·

If the engine cannot be started, check the engine speed while cranking the engine.

·

If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.





OK

43.CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE)

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT

43.CHECK HARNESS AND CONNECTOR (IGNITION COIL POWER SOURCE)
a.

Disconnect the ignition coil connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D26-1 (+B) - D26-4 (GND) Engine switch on (IG) 11 to 14 V
D27-1 (+B) - D27-4 (GND) Engine switch on (IG) 11 to 14 V
D28-1 (+B) - D28-4 (GND) Engine switch on (IG) 11 to 14 V
D29-1 (+B) - D29-4 (GND) Engine switch on (IG) 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

44.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL - IG2 RELAY)

44.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
a.

Disconnect the ignition coil connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D26-2 (IGF) - D2-81 (IGF1) Always Below 1 Ω
D27-2 (IGF) - D2-81 (IGF1) Always Below 1 Ω
D28-2 (IGF) - D2-81 (IGF1) Always Below 1 Ω
D29-2 (IGF) - D2-81 (IGF1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D26-2 (IGF) or D2-81 (IGF1) - Body ground Always 10 kΩ or higher
D27-2 (IGF) or D2-81 (IGF1) - Body ground Always 10 kΩ or higher
D28-2 (IGF) or D2-81 (IGF1) - Body ground Always 10 kΩ or higher
D29-2 (IGF) or D2-81 (IGF1) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

45.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
a.

Disconnect the ignition coil connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D26-3 (IGT1) - D2-85 (IGT1) Always Below 1 Ω
D27-3 (IGT2) - D2-84 (IGT2) Always Below 1 Ω
D28-3 (IGT3) - D2-83 (IGT3) Always Below 1 Ω
D29-3 (IGT4) - D2-82 (IGT4) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D26-3 (IGT1) or D2-85 (IGT1) - Body ground Always 10 kΩ or higher
D27-3 (IGT2) or D2-84 (IGT2) - Body ground Always 10 kΩ or higher
D28-3 (IGT3) or D2-83 (IGT3) - Body ground Always 10 kΩ or higher
D29-3 (IGT4) or D2-82 (IGT4) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness is normal, after replacing the ignition coil, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform troubleshooting for the ignition system (steps 78 to 83).





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard:
GTS Operation Specified Condition
ON Operating sound heard
OFF Operating sound not heard


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




OK

47.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

NG

47.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.

·

If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform fuel system troubleshooting (steps 73 to 77).





A

REPAIR OR REPLACE FUEL LINE

B

48.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


e.

Start the engine.


f.

While running the engine, read the Engine Speed value.

Standard:

A value that matches the actual engine speed is constantly output.


HINT:
·

Check the engine speed using a line graph.

·

If the engine cannot be started, check the engine speed while cranking the engine.

·

If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.





OK

49.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)

NG

49.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
a.

Disconnect the fuel injector connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D22-1 - Ground Engine switch on (IG) 11 to 14 V
D23-1 - Ground Engine switch on (IG) 11 to 14 V
D24-1 - Ground Engine switch on (IG) 11 to 14 V
D25-1 - Ground Engine switch on (IG) 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

50.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - IG2 RELAY)

50.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D22-2 - D2-108 (#10) Always Below 1 Ω
D23-2 - D2-107 (#20) Always Below 1 Ω
D24-2 - D2-106 (#30) Always Below 1 Ω
D25-2 - D2-105 (#40) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D22-2 or D2-108 (#10) - Body ground Always 10 kΩ or higher
D23-2 or D2-107 (#20) - Body ground Always 10 kΩ or higher
D24-2 or D2-106 (#30) - Body ground Always 10 kΩ or higher
D25-2 or D2-105 (#40) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.INSPECT MASS AIR FLOW METER

OK

52.CHECK INTAKE SYSTEM

NG

56.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
52.CHECK INTAKE SYSTEM
a.

Check for air suction in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (intake air volume is small) and almost the same as the normal values when racing the engine (intake air volume is high), air leakage may be present.



Standard:

There is no air suction.




OK

53.CHECK THROTTLE BODY ASSEMBLY

NG

REPAIR OR REPLACE INTAKE SYSTEM

53.CHECK THROTTLE BODY ASSEMBLY
a.

Disconnect the throttle body assembly connector.

HINT:

When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 6°.



b.

Crank the engine and check that it starts.

Result:
Result Proceed to
Engine starts A
Engine does not start B



c.

Connect the throttle body assembly connector.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).




A

54.CHECK THROTTLE BODY ASSEMBLY

B

55.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT SYSTEM)
54.CHECK THROTTLE BODY ASSEMBLY
a.

Check if carbon is in the air flow passage.

Standard:

No carbon present.




OK

55.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT SYSTEM)

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY ASSEMBLY

55.PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT SYSTEM)
A219635E01
1.073,0.987 1.330,1.143 0.257,0.156 10 ON 0.983,1.207 1.295,1.363 0.312,0.156 10 OFF 1.026,2.204 1.331,2.366 0.305,0.163 10 rpm 0.085,1.636 0.977,1.792 0.892,0.156 10 Engine Speed 0.079,0.483 1.063,0.658 0.984,0.175 10 OCV Operation

a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).

HINT:

When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.



f.

Check the engine speed while operating the Oil Control Valve (OCV) using the GTS.

OK:
GTS Operation Specified Condition
OFF Normal engine speed
ON Soon after OCV switched from OFF to ON, engine idles roughly or stalls


Result:
Result Proceed to
NG A
OK B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause the engine to stall.





A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE

B

72.CHECK MALFUNCTION CONDITION
56.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D3-5 (VG) - D2-118 (VG) Always Below 1 Ω
D3-4 (E2G) - D2-116 (E2G) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D3-5 (VG) or D2-118 (VG) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 72 and perform intake system troubleshooting (steps 84 to 86). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 87 to 94).





OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).

HINT:

If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.




OK

58.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

NG

58.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D7-2 (THW) - D2-97 (THW) Always Below 1 Ω
D7-1 (E2) - D2-96 (ETHW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D7-2 (THW) or D2-97 (THW) - Body ground Always 10 kΩ or higher
D7-1 (E2) or D2-96 (ETHW) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.





OK

59.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).

HINT:

If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.




OK

60.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

60.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D3-5 (VG) - D2-118 (VG) Always Below 1 Ω
D3-4 (E2G) - D2-116 (E2G) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D3-5 (VG) - D2-118 (VG) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.





OK

61.READ VALUE USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

61.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure and Long FT #1.


e.

Read the value.

Result:
Data List Item Result Suspected Area Proceed to
Long FT #1 +25% or more or less than -25%
·

Air fuel ratio sensor

·

Heated oxygen sensor

·

Mass air flow meter

·

Fuel injector

·

ECM


A
Atmosphere Pressure 80 kPa (600 mmHg) or less (when altitude is 0 m)
Both Data List items listed above Values are other than above - B




A

62.PERFORM SIMULATION TEST

B

66.CHECK FUEL PRESSURE
62.PERFORM SIMULATION TEST
a.

Remove the EFI and ETC-S fuses from the engine room relay block.


b.

After 60 seconds or more elapse, install the EFI and ETC-S fuses.


c.

Check if the engine can be started.

Result
Result Proceed to
Engine can be started A
Engine cannot be started B



A

63.INSPECT AIR FUEL RATIO SENSOR

B

66.CHECK FUEL PRESSURE
63.INSPECT AIR FUEL RATIO SENSOR
A353104E13
0.76,0.083 1.885,0.333 1.125,0.25 10 false Injection Volume 1.396,0.469 1.958,0.677 0.563,0.208 10 false +25% 1.323,0.771 1.885,0.979 0.563,0.208 10 false -12.5% 0.552,1.688 3.25,1.948 2.698,0.26 10 false Air Fuel Ratio Sensor Output Voltage 0.646,2.188 1.854,2.406 1.208,0.219 10 false Higher than 3.4 V 0.979,2.594 2.188,2.813 1.208,0.219 10 false Below 3.1 V 0.5,3.427 3.333,3.635 2.833,0.208 10 false Heated Oxygen Sensor Output Voltage 0.615,3.917 1.823,4.135 1.208,0.219 10 false Higher than 0.55 V 1.01,4.292 2.219,4.51 1.208,0.219 10 false Below 0.4 V 3.042,2.375 3.333,2.594 0.292,0.219 10 false OK 2.969,4.115 3.26,4.333 0.292,0.219 10 false OK

a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1.


e.

Confirm that Fuel System Status #1 are both CL.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / AF Lambda B1S1.


g.

Confirm that AF Lambda B1S1 is within the range of 0.95 to 1.05 when idling.


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


i.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
GTS Display Injection Volume Specified Condition
AFS Voltage B1S1 +25% Air fuel ratio sensor output voltage is below 3.1 V
-12.5% Air fuel ratio sensor output voltage is higher than 3.4 V


HINT:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the air fuel ratio sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.





OK

64.INSPECT HEATED OXYGEN SENSOR

NG

64.INSPECT HEATED OXYGEN SENSOR
a.

Inspect the heated oxygen sensor (See page Engine / Hybrid System>2AZ-FE EMISSION CONTROL>HEATED OXYGEN SENSOR>INSPECTION).

HINT:

If the heated oxygen sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 74 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.




OK

65.PERFORM SIMULATION TEST

NG

65.PERFORM SIMULATION TEST
a.

Check if the idling speed is stable after starting the engine.

OK:

Idling speed is stable.


HINT:

After replacing the fuel injector or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.




OK

NG

66.CHECK FUEL PRESSURE

OK

67.CHECK SPARK PLUG

NG

71.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
67.CHECK SPARK PLUG
a.

Inspect the spark plugs (See page Engine / Hybrid System>2AZ-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

Result
Result Proceed to
All cylinders are normal A
One cylinder is abnormal*1 B
All cylinders are abnormal*2, *3 C


HINT:
·

*1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.

·

*2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.

·

*3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.




A

68.CONFIRM VEHICLE CONDITION

B

REPLACE SPARK PLUG (ABNORMAL CYLINDER)

C

68.CONFIRM VEHICLE CONDITION
a.

Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

Result:
Problem Symptom Suspected Area Proceed to
When the engine is stopped and a long time has passed, engine starting trouble occurs*1 Pressure regulator is stuck open A
When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2 Fuel injector leak B
When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3 Failure to maintain fuel pressure by pressure regulator A
Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs - C*4


HINT:

*1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*2: Fuel may be leaking from a fuel injector.

*3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.

*4: From step 72, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.




A

69.CHECK FUEL PRESSURE

B

70.CHECK FUEL INJECTOR

C

72.CHECK MALFUNCTION CONDITION
69.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Result:
Result Proceed to
Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine) A
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine) B*


HINT:
·

If the engine cannot be started, check the fuel pressure after cranking the engine.

·

*: From step 72, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.





A

REPLACE PRESSURE REGULATOR

B

72.CHECK MALFUNCTION CONDITION
70.CHECK FUEL INJECTOR
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result:
Result Proceed to
4000 ppm or higher A
Less than 4000 ppm B*


HINT:
·

If the concentration is 4000 ppm or higher, a fuel injector may have a sealing problem.

·

*: From step 72, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.





A

B

72.CHECK MALFUNCTION CONDITION
71.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.

·

If there are no fuel leaks, after inspecting the fuel pump control system, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 72 and perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.





A

REPAIR OR REPLACE FUEL LINE

B

72.CHECK MALFUNCTION CONDITION
a.

If the malfunction could not be identified during the inspection in steps 38, 39, 40 and 47, perform fuel system troubleshooting C (steps 73 to 77).

Result:
Performed Step Troubleshooting by System Procedure Proceed to
Steps 38, 39, 40 and 47 Fuel system troubleshooting C 73 to 77 A



b.

If the malfunction could not be identified during the inspection in step 45, perform ignition system troubleshooting (steps 78 to 83).

Result:
Performed Step Troubleshooting by System Procedure Proceed to
Step 45 Ignition system troubleshooting 78 to 83 B



c.

If the malfunction could not be identified during the inspection in steps 55 and 56, perform intake air system troubleshooting (steps 84 to 86). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 87 to 94).

Result:
Performed Step Troubleshooting by System Procedure Proceed to
Step 55, 56 Intake air system troubleshooting 84 to 86 C
Fuel system troubleshooting A 87 to 94



d.

If the malfunction could not be identified during the inspection in steps 57, 58, 59, 60, 63, 64, 65, 67, 68, 69, 70 and 71, perform fuel system troubleshooting A (steps 95 to 102), fuel system troubleshooting B (steps 103 to 105), intake air system troubleshooting (steps 106 to 108), and ignition system troubleshooting (steps 109 to 114), in that order.

Result:
Performed Step Troubleshooting by System Procedure Proceed to
Steps 57, 58, 59, 60, 63, 64, 65, 67, 68, 69, 70 and 71 Fuel system troubleshooting A 95 to 102 D
Fuel system troubleshooting B 103 to 105
Intake air system troubleshooting 106 to 108
Ignition system troubleshooting 109 to 114




A

73.INSPECT FUEL INJECTOR

B

78.CHECK CRANKSHAFT POSITION SENSOR

C

84.READ VALUE USING GTS (ISC LEARNING VALUE)

D

95.CHECK FUEL PRESSURE
73.INSPECT FUEL INJECTOR
a.

Inspect the fuel injectors (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

74.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)

NG

74.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR POWER SOURCE)
a.

Disconnect the fuel injector connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D22-1 - Ground Engine switch on (IG) 11 to 14 V
D23-1 - Ground Engine switch on (IG) 11 to 14 V
D24-1 - Ground Engine switch on (IG) 11 to 14 V
D25-1 - Ground Engine switch on (IG) 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

75.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - IG2 RELAY)

75.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D22-2 - D2-108 (#10) Always Below 1 Ω
D23-2 - D2-107 (#20) Always Below 1 Ω
D24-2 - D2-106 (#30) Always Below 1 Ω
D25-2 - D2-105 (#40) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D22-2 or D2-108 (#10) - Body ground Always 10 kΩ or higher
D23-2 or D2-107 (#20) - Body ground Always 10 kΩ or higher
D24-2 or D2-106 (#30) - Body ground Always 10 kΩ or higher
D25-2 or D2-105 (#40) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

76.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

76.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

77.REPLACE CAMSHAFT POSITION SENSOR
77.REPLACE CAMSHAFT POSITION SENSOR
a.

b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)

NG

78.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

79.CHECK CAMSHAFT POSITION SENSOR

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

79.CHECK CAMSHAFT POSITION SENSOR
a.

Check the tightening and installation condition of the camshaft position sensor bolt.


b.

Check the connection of the camshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

80.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

80.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D54-1 - D2-122 (NE+) Always Below 1 Ω
D54-2 - D2-121 (NE-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D54-1 or D2-122 (NE+) - Body ground Always 10 kΩ or higher
D54-2 or D2-121 (NE-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

81.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

81.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D55-1 - D2-99 (G2+) Always Below 1 Ω
D55-2 - D2-98 (G2-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D55-1 - D2-99 (G2+) - Body ground Always 10 kΩ or higher
D55-2 - D2-98 (G2-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunction that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

82.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

82.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

83.REPLACE CAMSHAFT POSITION SENSOR
83.REPLACE CAMSHAFT POSITION SENSOR
a.

b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)

NG

84.READ VALUE USING GTS (ISC LEARNING VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.


e.

Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches off.

Result:
Data List Item Result Suspected Area Proceed to
ISC Learning Value (Engine displacement (liters) x 0.9) or more
·

Valve timing

·

Compression


A
Less than (engine displacement (liters) x 0.9) - B




A

85.CHECK CYLINDER COMPRESSION PRESSURE

B

86.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
85.CHECK CYLINDER COMPRESSION PRESSURE

OK

NG

REPAIR OR REPLACE ENGINE ASSEMBLY

86.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

87.CHECK FUEL PRESSURE

NG

87.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

Result:
Vehicle State Specified Condition
Cranking engine 304 to 343 kPa (3.1 to 3.5 kgf/cm2)
5 minutes after stopping engine 147 kPa (1.5 kgf/cm2) or more




OK

88.READ VALUE USING GTS (LONG FT #1)

NG

93.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
88.READ VALUE USING GTS (LONG FT #1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.

Result:
Data List Item Result Suspected Area Proceed to
Long FT #1 -15 to +15%
·

Wire harness or connector

·

Fuel


A
+15% or more, or less than -15% Fuel injector B




A

89.PERFORM SIMULATION TEST

B

89.PERFORM SIMULATION TEST
a.

Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

Result:
Problem Symptom Suspected Area Proceed to
Current unstable idling speed or history of unstable idling speed Crankshaft position sensor system A
All current and past idling speeds are stable Fuel B


HINT:

Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.




A

90.CHECK CRANKSHAFT POSITION SENSOR

B

REPLACE FUEL

90.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

91.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

91.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D54-1 - D2-122 (NE+) Always Below 1 Ω
D54-2 - D2-121 (NE-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D54-1 or D2-122 (NE+) - Body ground Always 10 kΩ or higher
D54-2 or D2-121 (NE-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

92.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

92.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

93.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.





A

REPAIR OR REPLACE FUEL LINE

B

94.INSPECT FUEL PUMP
94.INSPECT FUEL PUMP
a.


OK

REPLACE PRESSURE REGULATOR

NG

95.CHECK FUEL PRESSURE
HINT:

For the fuel pressure inspection, refer to the following procedures (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).


a.

Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

Result:
Result Proceed to
147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine) A
Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine) B




A

96.READ VALUE USING GTS (LONG FT #1)

B

101.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
96.READ VALUE USING GTS (LONG FT #1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.

Result:
Data List Item Result Suspected Area Proceed to
Long FT #1 -15 to +15%
·

Wire harness or connector

·

Fuel


A
+15% or more, or less than -15% Fuel injector B




A

97.PERFORM SIMULATION TEST

B

97.PERFORM SIMULATION TEST
a.

Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

Result
Problem Symptom Suspected Area Proceed to
Current unstable idling speed or history of unstable idling speed Crankshaft position sensor system A
All current and past idling speeds are stable Fuel B

HINT:

Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.




A

98.CHECK CRANKSHAFT POSITION SENSOR

B

REPLACE FUEL

98.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

99.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

99.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D54-1 - D2-122 (NE+) Always Below 1 Ω
D54-2 - D2-121 (NE-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D54-1 or D2-122 (NE+) - Body ground Always 10 kΩ or higher
D54-2 or D2-121 (NE-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

100.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

100.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

101.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


e.

When performing the Active Test, check for fuel leakage from the fuel pipes.

Result
Result Proceed to
Fuel leakage or signs of fuel leakage are present A
No fuel leakage or signs of fuel leakage B

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.

·

Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.





A

REPAIR OR REPLACE FUEL LINE

B

102.INSPECT FUEL PUMP
102.INSPECT FUEL PUMP
a.


OK

103.CHECK PURGE VSV

NG

103.CHECK PURGE VSV
a.
A172615

Disconnect the vacuum hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the purge VSV connector.


e.

Check if air flows through the purge VSV.

Standard:

Air does not flow



f.

Reconnect the purge VSV connector.


g.

Reconnect the vacuum hose.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).




OK

104.CHECK FUEL INJECTOR

NG

104.CHECK FUEL INJECTOR
a.

Clean the inside of the surge tank with compressed air.


b.

After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

Result:
Result Proceed to
4000 ppm or higher A
Less than 4000 ppm B


HINT:

If the concentration is 4000 ppm or higher, a fuel injector may have a sealing problem.




A

B

105.CHECK INTAKE VALVE
105.CHECK INTAKE VALVE
a.

Check if carbon is on the intake valves.

Result:
Result Proceed to
Carbon present A
No carbon present B




A

CLEAN INTAKE VALVE

B

106.READ VALUE USING GTS (ISC LEARNING VALUE)
106.READ VALUE USING GTS (ISC LEARNING VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.


e.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

Result:
Data List Item Result Suspected Area Proceed to
ISC Learning Value (engine displacement (liters) x 0.9) or more
·

Valve timing

·

Compression


A
Less than (engine displacement (liters) x 0.9) - B




A

107.CHECK CYLINDER COMPRESSION PRESSURE

B

108.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
107.CHECK CYLINDER COMPRESSION PRESSURE

OK

NG

REPAIR OR REPLACE ENGINE ASSEMBLY

108.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

109.CHECK CRANKSHAFT POSITION SENSOR

NG

109.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the tightening and installation condition of the crankshaft position sensor bolt.


b.

Check the connection of the crankshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

110.CHECK CAMSHAFT POSITION SENSOR

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

110.CHECK CAMSHAFT POSITION SENSOR
a.

Check the tightening and installation condition of the camshaft position sensor bolt.


b.

Check the connection of the camshaft position sensor connector.

OK:

Sensor is installed correctly.




OK

111.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

111.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D54-1 - D2-122 (NE+) Always Below 1 Ω
D54-2 - D2-121 (NE-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D54-1 or D2-122 (NE+) - Body ground Always 10 kΩ or higher
D54-2 or D2-121 (NE-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

112.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

112.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor for intake side connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D55-1 - D2-99 (G2+) Always Below 1 Ω
D55-2 - D2-98 (G2-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D55-1 or D2-99 (G2+) - Body ground Always 10 kΩ or higher
D55-2 or D2-98 (G2-) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunction that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.





OK

113.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

113.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).


b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE)

NG

114.REPLACE CAMSHAFT POSITION SENSOR
114.REPLACE CAMSHAFT POSITION SENSOR
a.

b.

Check the engine start operation.

OK:

Malfunction has been repaired successfully.




OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)

NG