Not in the contents tree

578 documents the disc carries but never lists. Where they belong is not recorded anywhere on the disc, so they are left here rather than filed on a guess. A further 54 were exact copies of documents the tree does list, and are not repeated.

• *AIRBAG SYSTEM VERIFICATION TEST - VER 1 · *AIRBAG SYSTEM VERIFICATION TEST - VER 1 1. *AIRBAG SYSTEM VERIFICATION TEST - VER 1 1. Remove all special tools and jumper wires and reconnect all pr...
• *DIAGNOSIS AND CHECKOUT PROCEDURE FOR SEAT WEIGHT SENSORS · *DIAGNOSIS AND CHECKOUT PROCEDURE FOR SEAT WEIGHT SENSORS 1. VERIFY COMPLAINT Turn the ignition off. Move the front passenger seat to the full rear po...
• *OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST · *OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST Diagnostic Test 1. PERFORM THE *OCM SYSTEM VERIFICATION TEST NOTE: Ensure that the battery is...
• *ONE PASSENGER DOOR LOCK INOPERATIVE · *ONE PASSENGER DOOR LOCK INOPERATIVE For a complete wiring diagram Refer to Section 8W . Possible Causes (P32), (P38) OR (P920) DOOR LOCK DRIVER CIRCU...
• 2.8L DIESEL · 2.8L DIESEL 1. Check condition of all pulleys. CAUTION: When installing the accessory drive belt, the belt MUST be routed correctly. If not, the engin...
• 2.8L DIESEL · 2.8L DIESEL 1. Disconnect negative battery cable. 2. Remove accessory drive belt (9) (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELTS - REMOVAL) . 3....
• 2.8L DIESEL · 2.8L DIESEL 1. Install idler pulleys and retaining bolts . Torque bolts to 53 N·m. 2. Install accessory drive belt (Refer to 7 - COOLING/ACCESSORY DRI...
• 2.8L DIESEL · 2.8L DIESEL 1. Position new turbocharger to front exhaust pipe and catalytic converter clamp (1) on turbocharger. 2. Position the front exhaust pipe a...
• 2.8L DIESEL · 2.8L DIESEL CAUTION: DO not let tensioner arm snap back to the freearm position, severe damage may occur to the tensioner. Belt tension is not adjusta...
• 2.8L DIESEL · 2.8L DIESEL CAUTION: The retaining bolts on the idler pulleys are left hand thread. 1. Disconnect negative battery cable. 2. Remove accessory drive be...
• 2.8L DIESEL ENGINE · 2.8L DIESEL ENGINE 1. Clean old gasket material from cylinder head and thermostat housing. 2. Install thermostat housing with gasket and support brack...
• 2.8L DIESEL ENGINE · 2.8L DIESEL ENGINE NOTE: The thermostat is not serviced separately. The thermostat and housing must be replaced as an assembly. 1. Disconnect negative...
• 2.8L DIESEL ENGINE · 2.8L DIESEL ENGINE The water pump on the 2.8L CRD diesel has a die cast aluminum housing. It bolts to an aluminum housing which attaches to the engine...
• 2.8L DIESEL ENGINE · 2.8L DIESEL ENGINE WARNING: If torches are used when working on the exhaust system, do not allow the flame near the fuel lines. 1. Raise and support t...
• 2.8L–DIESEL · 2.8L–DIESEL 1. Install the pump to the vehicle. 2. Install the three bolts (2) securing the pump (1) to the engine and tighten to 26 N·m (19 ft. lbs.)...
• 3.8L · 3.8L 1. An indexing slot is located on back of tensioner. Align this slot to the head of the bolt on the front cover. Install the mounting bolt. Tight...
• 3.8L · 3.8L 1. Check condition of all pulleys. CAUTION: When installing the accessory drive belt, the belt MUST be routed correctly. If not, the engine may o...
• 3.8L · 3.8L 1. Remove accessory drive belt (Refer to 7 - COOLING/ACCESSORY DRIVE/DRIVE BELTS - REMOVAL) . 2. Remove tensioner assembly from engine front cove...
• 3.8L · 3.8L CAUTION: Do not let tensioner arm snap back to the freearm position, severe damage may occur to the tensioner. 1. Disconnect negative battery cab...
• 42RLE TRANSMISSION VERIFICATION TEST · 42RLE TRANSMISSION VERIFICATION TEST Perform the following after completion of a diagnostic repair: NOTE: After completion of the Transmission Verific...
• A/C COMPRESSOR · A/C COMPRESSOR This A/C system uses a Zexel DKS-17DS ten cylinder, double-acting swash plate-type A/C compressor (1). This A/C compressor has a fixed ...
• A/C COMPRESSOR CLUTCH COIL · A/C COMPRESSOR CLUTCH COIL The A/C compressor clutch coil electrical circuit is controlled by the powertrain control module (PCM) through the A/C clut...
• A/C SYSTEM · A/C SYSTEM Item Description Notes A/C Compressor Zexel DKS-17DS ZXL-100 PAG Oil Freeze-up Control Evaporator Temperature Sensor HVAC housing mounted -...
• ABS INTERMITTENT CONDITION · ABS INTERMITTENT CONDITION For a complete wiring diagram Refer to Section 8W . Diagnostic Test 1. PERFORM ABS INTERMITTENT CONDITION TEST NOTE: The co...
• ALIGNMENT SPECIFICATIONS · ALIGNMENT SPECIFICATIONS NOTE: Alignment specifications are in degrees. DESCRIPTION SPECIFICATION PREFERRED CASTER + 4.2° CAMBER (fixed angle) − 0.25°...
• ASSEMBLY · ASSEMBLY WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting an...
• ASSEMBLY · ASSEMBLY WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting an...
• ASSEMBLY · ASSEMBLY WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting an...
• ASSEMBLY - ROCKER ARMS AND SHAFT · ASSEMBLY - ROCKER ARMS AND SHAFT 1. Install rocker arms on the shaft. Install in the original positions if re-used. Ensure the rocker shaft, all the r...
• B10C1–A/C SELECT SWITCH STUCK (CCN) · B10C1–A/C SELECT SWITCH STUCK (CCN) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: If the In...
• B10C2 – REAR DEFROST SWITCH STUCK (CCN) · B10C2 – REAR DEFROST SWITCH STUCK (CCN) For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition: When the Rear ...
• B1409-REAR LEFT AUDIO SPEAKER OUTPUT CIRCUIT LOW · B1409-REAR LEFT AUDIO SPEAKER OUTPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the radio on. Set Condition:...
• B140D-REAR RIGHT AUDIO SPEAKER OUTPUT CIRCUIT LOW · B140D-REAR RIGHT AUDIO SPEAKER OUTPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the radio on. Set Condition...
• B1423-VES DVD READ ERROR/INOPERABLE DISC · B1423-VES DVD READ ERROR/INOPERABLE DISC For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously with the ignition on and the...
• B1424-IMPROPER DVD-WRONG REGION · B1424-IMPROPER DVD-WRONG REGION For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously with the ignition on and the DVD play...
• B1429-RADIO DISPLAY HIGH TEMPERATURE · B1429-RADIO DISPLAY HIGH TEMPERATURE For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously with the ignition and Radio on. ...
• B142A-RADIO UNIT HIGH TEMPERATURE · B142A-RADIO UNIT HIGH TEMPERATURE For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously with the ignition and Radio on. Set...
• B142C-VES VIDEO SCREEN DISCONNECTED · B142C-VES VIDEO SCREEN DISCONNECTED For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and the Radio in Video mo...
• B142D-AUDIO ANTENNA NOT CONNECTED · B142D-AUDIO ANTENNA NOT CONNECTED For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and the Radio in seek mode....
• B142E-GPS ANTENNA NOT CONNECTED · B142E-GPS ANTENNA NOT CONNECTED For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and the Radio in Navigation m...
• B146D-CHANNEL 3 AUDIO SPEAKER OUTPUT CIRCUIT OPEN · B146D-CHANNEL 3 AUDIO SPEAKER OUTPUT CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: Amplifier BUS wake-up. Amplifier...
• B1470-CHANNEL 4 AUDIO SPEAKER OUTPUT CIRCUIT LOW · B1470-CHANNEL 4 AUDIO SPEAKER OUTPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Conditi...
• B1472-CHANNEL 4 AUDIO SPEAKER OUTPUT CIRCUIT OPEN · B1472-CHANNEL 4 AUDIO SPEAKER OUTPUT CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: Amplifier BUS wake-up. Amplifier...
• B1473-CHANNEL 4 AUDIO SPEAKER OUTPUT CIRCUIT SHORTED TOGETHER · B1473-CHANNEL 4 AUDIO SPEAKER OUTPUT CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on...
• B1801 DRIVER DOOR LOCK/UNLOCK SWITCH CIRCUIT LOW – TIPM · B1801 DRIVER DOOR LOCK/UNLOCK SWITCH CIRCUIT LOW – TIPM For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition...
• B1806 PASSENGER DOOR LOCK/UNLOCK SWITCH CIRCUIT LOW – TIPM · B1806 PASSENGER DOOR LOCK/UNLOCK SWITCH CIRCUIT LOW – TIPM For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condit...
• B1934–DRIVER DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK – TIPM · B1934–DRIVER DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK – TIPM For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Conditi...
• B1935–PASSENGER DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK – TIPM · B1935–PASSENGER DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK – TIPM For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Cond...
• B1A25-INVALID KEY · B1A25-INVALID KEY For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Set Condition: W...
• B1A26–MAXIMUM NUMBER OF KEYS PROGRAMMED · B1A26–MAXIMUM NUMBER OF KEYS PROGRAMMED For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: When ...
• B1A28-ECM MISMATCH WITH SKIM · B1A28-ECM MISMATCH WITH SKIM For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on, after ignition on during any rolling ...
• B1A29-SKIM BASESTATION MISMATCH · B1A29-SKIM BASESTATION MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on, after ignition on during any rolli...
• B1A2A-KEY 1 COMMUNICATION ERROR · B1A2A-KEY 1 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A2B-KEY 2 COMMUNICATION ERROR · B1A2B-KEY 2 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A2C-KEY 3 COMMUNICATION ERROR · B1A2C-KEY 3 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A2D-KEY 4 COMMUNICATION ERROR · B1A2D-KEY 4 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A2E-KEY 5 COMMUNICATION ERROR · B1A2E-KEY 5 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A2F-KEY 6 COMMUNICATION ERROR · B1A2F-KEY 6 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A30-KEY 7 COMMUNICATION ERROR · B1A30-KEY 7 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A31-KEY 8 COMMUNICATION ERROR · B1A31-KEY 8 COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programming Mode. Se...
• B1A35-UNIDENTIFIED KEY COMMUNICATION ERROR · B1A35-UNIDENTIFIED KEY COMMUNICATION ERROR For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on and during Key Programmi...
• B1B00-DRIVER AIRBAG SQUIB 1 CIRCUIT LOW · B1B00-DRIVER AIRBAG SQUIB 1 CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The O...
• B1B01-DRIVER AIRBAG SQUIB 1 CIRCUIT HIGH · B1B01-DRIVER AIRBAG SQUIB 1 CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1B02-DRIVER AIRBAG SQUIB 1 CIRCUIT OPEN · B1B02-DRIVER AIRBAG SQUIB 1 CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1B03-DRIVER AIRBAG SQUIB 1 CIRCUIT SHORTED TOGETHER · B1B03-DRIVER AIRBAG SQUIB 1 CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Con...
• B1B04-DRIVER AIRBAG SQUIB 2 CIRCUIT LOW · B1B04-DRIVER AIRBAG SQUIB 2 CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The O...
• B1B05-DRIVER AIRBAG SQUIB 2 CIRCUIT HIGH · B1B05-DRIVER AIRBAG SQUIB 2 CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1B06-DRIVER AIRBAG SQUIB 2 CIRCUIT OPEN · B1B06-DRIVER AIRBAG SQUIB 2 CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1B07-DRIVER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER · B1B07-DRIVER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Con...
• B1B08-PASSENGER AIRBAG SQUIB 1 CIRCUIT LOW · B1B08-PASSENGER AIRBAG SQUIB 1 CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: Th...
• B1B09-PASSENGER AIRBAG SQUIB 1 CIRCUIT HIGH · B1B09-PASSENGER AIRBAG SQUIB 1 CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on Set Condition: Th...
• B1B0A-PASSENGER AIRBAG SQUIB 1 CIRCUIT OPEN · B1B0A-PASSENGER AIRBAG SQUIB 1 CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: T...
• B1B0B-PASSENGER AIRBAG SQUIB 1 CIRCUIT SHORTED TOGETHER · B1B0B-PASSENGER AIRBAG SQUIB 1 CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set ...
• B1B0C-PASSENGER AIRBAG SQUIB 2 CIRCUIT LOW · B1B0C-PASSENGER AIRBAG SQUIB 2 CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: Th...
• B1B0D-PASSENGER AIRBAG SQUIB 2 CIRCUIT HIGH · B1B0D-PASSENGER AIRBAG SQUIB 2 CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: T...
• B1B0E-PASSENGER AIRBAG SQUIB 2 CIRCUIT OPEN · B1B0E-PASSENGER AIRBAG SQUIB 2 CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: T...
• B1B0F-PASSENGER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER · B1B0F-PASSENGER AIRBAG SQUIB 2 CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set ...
• B1B54-1ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT LOW · B1B54-1ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and the ...
• B1B55-1 ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT HIGH · B1B55-1 ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and th...
• B1B56-1ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT OPEN · B1B56-1ST ROW PASSENGER SEAT BELT SENSOR CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and the...
• B1B70-UP-FRONT LEFT SATELLITE ACCELERATION SENSOR INTERNAL · B1B70-UP-FRONT LEFT SATELLITE ACCELERATION SENSOR INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, t...
• B1B71-UP-FRONT RIGHT SATELLITE ACCELERATION SENSOR INTERNAL · B1B71-UP-FRONT RIGHT SATELLITE ACCELERATION SENSOR INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, ...
• B1B72-LEFT SIDE SATELLITE ACCELERATION SENSOR 1 INTERNAL · B1B72-LEFT SIDE SATELLITE ACCELERATION SENSOR 1 INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, the...
• B1B75-RIGHT SIDE SATELLITE ACCELERATION SENSOR 1 INTERNAL · B1B75-RIGHT SIDE SATELLITE ACCELERATION SENSOR 1 INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, th...
• B1B78-PASSENGER SEAT WEIGHT SENSOR 3 - LEFT FRONT PERFORMANCE · B1B78-PASSENGER SEAT WEIGHT SENSOR 3 - LEFT FRONT PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: When CAN ignitions s...
• B1B79-PASSENGER SEAT WEIGHT SENSOR 3 - LEFT FRONT INPUT CIRCUIT LOW · B1B79-PASSENGER SEAT WEIGHT SENSOR 3 - LEFT FRONT INPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN ...
• B1B7A-PASSENGER SEAT WEIGHT SENSOR 3 - LEFT FRONT INPUT CIRCUIT HIGH · B1B7A-PASSENGER SEAT WEIGHT SENSOR 3 - LEFT FRONT INPUT CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN...
• B1B7D-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT PERFORMANCE · B1B7D-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: When CAN ignitions ...
• B1B7E-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT INPUT CIRCUIT LOW · B1B7E-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT INPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN...
• B1B7F-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT INPUT CIRCUIT HIGH · B1B7F-PASSENGER SEAT WEIGHT SENSOR 2 - RIGHT FRONT INPUT CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CA...
• B1B82-PASSENGER SEAT WEIGHT SENSOR 4 - LEFT REAR PERFORMANCE · B1B82-PASSENGER SEAT WEIGHT SENSOR 4 - LEFT REAR PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: When CAN ignitions st...
• B1B83-PASSENGER SEAT WEIGHT SENSOR 4 - LEFT REAR INPUT CIRCUIT LOW · B1B83-PASSENGER SEAT WEIGHT SENSOR 4 - LEFT REAR INPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN b...
• B1B84-PASSENGER SEAT WEIGHT SENSOR 4 - LEFT REAR INPUT CIRCUIT HIGH · B1B84-PASSENGER SEAT WEIGHT SENSOR 4 - LEFT REAR INPUT CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN ...
• B1B87-PASSENGER SEAT WEIGHT SENSOR 1 - RIGHT REAR PERFORMANCE · B1B87-PASSENGER SEAT WEIGHT SENSOR 1 - RIGHT REAR PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: When CAN ignitions s...
• B1B88-PASSENGER SEAT WEIGHT SENSOR 1 - RIGHT REAR INPUT CIRCUIT LOW · B1B88-PASSENGER SEAT WEIGHT SENSOR 1 - RIGHT REAR INPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN ...
• B1B89-PASSENGER SEAT WEIGHT SENSOR 1 - RIGHT REAR INPUT CIRCUIT HIGH · B1B89-PASSENGER SEAT WEIGHT SENSOR 1 - RIGHT REAR INPUT CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN...
• B1B8D-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT LOW · B1B8D-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition sta...
• B1B8E-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT HIGH · B1B8E-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition st...
• B1B8F-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT OPEN · B1B8F-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition st...
• B1B93-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT LOW · B1B93-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition ...
• B1B94-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT HIGH · B1B94-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition...
• B1B95-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT OPEN · B1B95-PASSENGER SEAT TRACK POSITION SENSOR CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition...
• B1BA5-AIRBAG SQUIB CONFIGURATION MISMATCH · B1BA5-AIRBAG SQUIB CONFIGURATION MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: If ...
• B1BA6-OCCUPANT CLASSIFICATION UNDETERMINED · B1BA6-OCCUPANT CLASSIFICATION UNDETERMINED When Monitored: With the ignition on. Set Condition: Because other DTCs have made occupant detection imposs...
• B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED · B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED When Monitored: With the CAN ignition status as IGN_RUN, the module tries to detect potenti...
• B1BA8-OCM SYSTEM OUT OF CALIBRATION/NOT CALIBRATED · B1BA8-OCM SYSTEM OUT OF CALIBRATION/NOT CALIBRATED When Monitored: While the CAN bus ignition status is IGN_RUN or signal not available. Set Condition...
• B1BAA-OCCUPANT CLASSIFICATION MODULE CONFIGURATION MISMATCH · B1BAA-OCCUPANT CLASSIFICATION MODULE CONFIGURATION MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus igni...
• B1BBA-PASSENGER SEAT WEIGHT SENSOR SUPPLY CIRCUIT · B1BBA-PASSENGER SEAT WEIGHT SENSOR SUPPLY CIRCUIT For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition statu...
• B1BBB-PASSENGER SEAT WEIGHT SENSOR INPUTS SHORTED TOGETHER · B1BBB-PASSENGER SEAT WEIGHT SENSOR INPUTS SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignit...
• B1BBC-OCS NEGATIVE SYSTEM WEIGHT · B1BBC-OCS NEGATIVE SYSTEM WEIGHT When Monitored: While the CAN bus ignition status is in IGN_RUN, the module checks the sensor input ranges. Set Condi...
• B1BBD-OCM CURRENT CONFIGURATION TABLE UNPROGRAMMED · B1BBD-OCM CURRENT CONFIGURATION TABLE UNPROGRAMMED For a complete wiring diagram Refer to Section 8W . When Monitored: If the Configuration Table is n...
• B1BC7-DEPLOYMENT DATA RECORD FULL · B1BC7-DEPLOYMENT DATA RECORD FULL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. The Occupant Restraint Con...
• B1C27-LEFT SIDE SEAT THORAX SQUIB 1 LOW · B1C27-LEFT SIDE SEAT THORAX SQUIB 1 LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The O...
• B1C28-LEFT SIDE SEAT THORAX SQUIB 1 HIGH · B1C28-LEFT SIDE SEAT THORAX SQUIB 1 HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN · B1C29-LEFT SIDE SEAT THORAX SQUIB 1 OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1C2A-LEFT SIDE SEAT THORAX SQUIB 1 SHORTED TOGETHER · B1C2A-LEFT SIDE SEAT THORAX SQUIB 1 SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Con...
• B1C2B-RIGHT SIDE SEAT THORAX SQUIB 1 LOW · B1C2B-RIGHT SIDE SEAT THORAX SQUIB 1 LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The ...
• B1C2C-RIGHT SIDE SEAT THORAX SQUIB 1 HIGH · B1C2C-RIGHT SIDE SEAT THORAX SQUIB 1 HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The...
• B1C2D-RIGHT SIDE SEAT THORAX SQUIB 1 OPEN · B1C2D-RIGHT SIDE SEAT THORAX SQUIB 1 OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The...
• B1C2E-RIGHT SIDE SEAT THORAX SQUIB 1 SHORTED TOGETHER · B1C2E-RIGHT SIDE SEAT THORAX SQUIB 1 SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Co...
• B1C38-1st ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT LOW · B1C38-1st ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, the ...
• B1C39-1ST ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT HIGH · B1C39-1ST ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, the...
• B1C3A-1st ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT OPEN · B1C3A-1st ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, the...
• B1C3B-1st ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT SHORTED TOGETHER · B1C3B-1st ROW DRIVER RETRACTOR PRETENSIONER CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the igni...
• B1C47-1st ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT LOW · B1C47-1st ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, t...
• B1C48-1ST ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT HIGH · B1C48-1ST ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, ...
• B1C49-1st ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT OPEN · B1C49-1st ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on, ...
• B1C4A-1st ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT SHORTED TOGETHER · B1C4A-1st ROW PASSENGER RETRACTOR PRETENSIONER CIRCUIT SHORTED TOGETHER For a complete wiring diagram Refer to Section 8W . When Monitored: With the i...
• B2101-IGNITION RUN/START INPUT CIRCUIT LOW · B2101-IGNITION RUN/START INPUT CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus is RUN or SNA (signal...
• B2101-IGNITION RUN/START INPUT LOW · B2101-IGNITION RUN/START INPUT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: The...
• B2101-IGNITION RUN/START INPUT LOW · B2101-IGNITION RUN/START INPUT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: The...
• B2102-IGNITION RUN/START INPUT CIRCUIT HIGH · B2102-IGNITION RUN/START INPUT CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition status is R...
• B2102-IGNITION RUN/START INPUT HIGH · B2102-IGNITION RUN/START INPUT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: Th...
• B210A-SYSTEM VOLTAGE LOW · B210A-SYSTEM VOLTAGE LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: The SKREEM ha...
• B210D-BATTERY VOLTAGE LOW · B210D-BATTERY VOLTAGE LOW For a complete wiring diagram Refer to Section 8W . When Monitored: While the Occupant Classification Module (OCM) CAN bus i...
• B210D-BATTERY VOLTAGE LOW · B210D-BATTERY VOLTAGE LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: The SKREEM h...
• B210D-SYSTEM VOLTAGE HIGH · B210D-SYSTEM VOLTAGE HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: The SKREEM h...
• B210E-BATTERY VOLTAGE HIGH · B210E-BATTERY VOLTAGE HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: While the CAN bus ignition status received is RUN or SN...
• B210E-BATTERY VOLTAGE HIGH · B210E-BATTERY VOLTAGE HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: Battery voltage gr...
• B210E-BATTERY VOLTAGE HIGH · B210E-BATTERY VOLTAGE HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition switch on. Set Condition: The SKREEM ...
• B212C-IGNITION RUN/START INPUT CIRCUIT OPEN · B212C-IGNITION RUN/START INPUT CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition in the Run-Start pos...
• B212D-IGNITION RUN ONLY INPUT CIRCUIT OPEN · B212D-IGNITION RUN ONLY INPUT CIRCUIT OPEN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition in the Run position. ...
• B2142 IGNITION OFF DRAW (IOD) FUSE NOT PRESENT · B2142 IGNITION OFF DRAW (IOD) FUSE NOT PRESENT For a complete wiring diagram Refer to Section 8W . When Monitored: With the Ignition on. Set Condition...
• B219F IGNITION OFF DRAW (IOD) FUSE BLOWN · B219F IGNITION OFF DRAW (IOD) FUSE BLOWN For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: IOD ...
• B2201-CALIBRATION MISMATCH · B2201-CALIBRATION MISMATCH When Monitored: With the Ignition on. Set Condition: This DTC will be set when the VIN stored in the PCM does not match the...
• B2204-ECU CONFIGURATION MISMATCH · B2204-ECU CONFIGURATION MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Possible Causes SENTRY KEY ...
• B2205-ORIGINAL VIN MISSING/MISMATCH · B2205-ORIGINAL VIN MISSING/MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: At ignition on, after ignition on during any r...
• B2205-ORIGINAL VIN MISSING/MISMATCH · B2205-ORIGINAL VIN MISSING/MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The Occup...
• B2206-CURRENT VIN MISSING / MISMATCH · B2206-CURRENT VIN MISSING / MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: A PCM fr...
• B2206-CURRENT VIN MISSING/MISMATCH · B2206-CURRENT VIN MISSING/MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: During power-up, the Occupant Restraint Control...
• B2207-OCCUPANT RESTRAINT CONTROLLER INTERNAL 1 · B2207-OCCUPANT RESTRAINT CONTROLLER INTERNAL 1 For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. The module's ...
• B2208-OCCUPANT RESTRAINT CONTROLLER INTERNAL 2 · B2208-OCCUPANT RESTRAINT CONTROLLER INTERNAL 2 When Monitored: With the ignition on. The module's on board diagnostics continuously performs internal ...
• B2209-OCCUPANT RESTRAINT CONTROLLER INTERNAL 3 · B2209-OCCUPANT RESTRAINT CONTROLLER INTERNAL 3 When Monitored: With the ignition on. The module's on board diagnostics continuously performs internal ...
• B220A-OCCUPANT RESTRAINT CONTROLLER INTERNAL 4 · B220A-OCCUPANT RESTRAINT CONTROLLER INTERNAL 4 When Monitored: With the ignition on. The module's on board diagnostics continuously performs internal ...
• B220B-OCCUPANT RESTRAINT CONTROLLER FIRING STORED ENERGY · B220B-OCCUPANT RESTRAINT CONTROLLER FIRING STORED ENERGY When Monitored: With the ignition on. The module's on board diagnostics continuously performs...
• B220C-OCCUPANT RESTRAINT CONTROLLER ACCELEROMETER 1 INTERNAL · B220C-OCCUPANT RESTRAINT CONTROLLER ACCELEROMETER 1 INTERNAL When Monitored: With the ignition on. The module's on board diagnostics continuously perf...
• B220D-OCCUPANT RESTRAINT CONTROLLER ACCELEROMETER 2 INTERNAL · B220D-OCCUPANT RESTRAINT CONTROLLER ACCELEROMETER 2 INTERNAL When Monitored: With the ignition on. The module's on board diagnostics continuously perf...
• B2212-OCCUPANT CLASSIFICATION MODULE INTERNAL · B2212-OCCUPANT CLASSIFICATION MODULE INTERNAL When Monitored: While the IGN status is RUN or signal not available, while the CAN bus system voltage is...
• B2215–FCM INTERNAL (TIPM) · B2215–FCM INTERNAL (TIPM) For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously. Set Condition: The TIPM detects an interna...
• B2222-SATELLITE RADIO RECEIVER INTERNAL · B2222-SATELLITE RADIO RECEIVER INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The S...
• B2224–SKREEM INTERNAL · B2224–SKREEM INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Possible Causes SENTRY KEY REMOTE ENTR...
• B2228-SKREEM INTERNAL - RKE RECEIVER · B2228-SKREEM INTERNAL - RKE RECEIVER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Possible Causes SENTRY ...
• B2229-SKREEM INTERNAL - SKIM IMMOBILIZER · B2229-SKREEM INTERNAL - SKIM IMMOBILIZER For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Possible Causes SEN...
• B222A-VEHICLE LINE MISMATCH · B222A-VEHICLE LINE MISMATCH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The Totally Integ...
• B222C-VEHICLE CONFIGURATION NOT PROGRAMMED · B222C-VEHICLE CONFIGURATION NOT PROGRAMMED For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition: The TIPM de...
• B223B-VEHICLE CONFIGURATION MISMATCH · B223B-VEHICLE CONFIGURATION MISMATCH When Monitored: With the ignition on. Set Condition: The Totally Integrated Power Module (TIPM) sends a message t...
• B223D-OCCUPANT CLASSIFICATION MODULE DTC PRESENT · B223D-OCCUPANT CLASSIFICATION MODULE DTC PRESENT When Monitored: With the ignition on. Set Condition: This DTC will set if the ORC receives a bus mess...
• B2304-WIPER PARK SWITCH INPUT CIRCUIT LOW (STUCK LOW) · B2304-WIPER PARK SWITCH INPUT CIRCUIT LOW (STUCK LOW) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Co...
• B2305-WIPER PARK SWITCH INPUT CIRCUIT HIGH (STUCK HIGH) · B2305-WIPER PARK SWITCH INPUT CIRCUIT HIGH (STUCK HIGH) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set ...
• B230D-REAR WIPER PARK SWITCH INPUT CIRCUIT LOW (STUCK LOW) · B230D-REAR WIPER PARK SWITCH INPUT CIRCUIT LOW (STUCK LOW) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. S...
• B230E-REAR WIPER PARK SWITCH INPUT CIRCUIT HIGH (STUCK HIGH) · B230E-REAR WIPER PARK SWITCH INPUT CIRCUIT HIGH (STUCK HIGH) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on....
• B2323–HEADLAMP WASHER MOTOR CONTROL CIRCUIT LOW · B2323–HEADLAMP WASHER MOTOR CONTROL CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the Headlamp Washers activate...
• B2339–HORN SWITCH STUCK – CLUSTER · B2339–HORN SWITCH STUCK – CLUSTER For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition: When the Cluster sen...
• BATTERY SYSTEM · BATTERY SYSTEM The battery, starting, and charging systems in the vehicle operate with one another and must be tested as a complete system. In order f...
• BODY OPENING DIMENSIONS · BODY OPENING DIMENSIONS Index DESCRIPTION FIGURE ENGINE BOX ENGINE BOX WINDSHIELD OPENING WINDSHIELD OPENING FRONT DOOR OPENING - JK 72 ONLY FRONT DOO...
• BRAKE COMPONENTS · BRAKE COMPONENTS SPECIFICATIONS DESCRIPTION SPECIFICATION Disc Brake Caliper Type Sliding Disc Brake Rotor Type Front Ventilated Disc Brake Rotor Type...
• BRAKE INDICATOR · BRAKE INDICATOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemp...
• BRAKE LAMP SWITCH · BRAKE LAMP SWITCH WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before atte...
• BRAKE LAMP SWITCH · BRAKE LAMP SWITCH WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before atte...
• BULB · BULB 1. Disconnect and isolate the battery negative cable. 2. Insert the tip of a small flat-bladed screwdriver into the notch on the right side of th...
• BULB · BULB 1. Disconnect and isolate the battery negative cable. 2. Insert the tip of a small flat-bladed screwdriver into the notch on the right side of th...
• BULB · BULB CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the...
• BULB · BULB CAUTION: Always use the correct bulb size and type for replacement. An incorrect bulb size or type may overheat and cause damage to the lamp, the...
• BULB · BULB WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any st...
• BULB · BULB WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any st...
• C0077- LOW TIRE PRESSURE · C0077- LOW TIRE PRESSURE For a complete wiring diagram Refer to Section 8W . Theory of Operation The Tire Pressure Monitoring System (TPMS) will warn ...
• C1011-LEFT FRONT WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE · C1011-LEFT FRONT WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition o...
• C1014-LEFT FRONT WHEEL SPEED COMPARATIVE PERFORMANCE · C1014-LEFT FRONT WHEEL SPEED COMPARATIVE PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Con...
• C1015–RIGHT FRONT WHEEL SPEED SENSOR CIRCUIT · C1015–RIGHT FRONT WHEEL SPEED SENSOR CIRCUIT For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: ...
• C101C-RIGHT FRONT WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE · C101C-RIGHT FRONT WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition ...
• C101F-RIGHT FRONT WHEEL SPEED COMPARATIVE PERFORMANCE · C101F-RIGHT FRONT WHEEL SPEED COMPARATIVE PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Co...
• C1027-LEFT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE · C1027-LEFT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on...
• C102A-LEFT REAR WHEEL SPEED COMPARATIVE PERFORMANCE · C102A-LEFT REAR WHEEL SPEED COMPARATIVE PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Cond...
• C1032-RIGHT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE · C1032-RIGHT REAR WHEEL SPEED SENSOR SIGNAL ERRATIC PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition o...
• C1035-RIGHT REAR WHEEL SPEED COMPARATIVE PERFORMANCE · C1035-RIGHT REAR WHEEL SPEED COMPARATIVE PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Con...
• C1042-RIGHT FRONT TONE WHEEL PERFORMANCE · C1042-RIGHT FRONT TONE WHEEL PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: When...
• C107C–BRAKE PEDAL SWITCH 1/2 STUCK · C107C–BRAKE PEDAL SWITCH 1/2 STUCK For a complete wiring diagram Refer to Section 8W . 1. ENGINE DTCS PRESENT With the scan tool, read Engine DTCs. Ar...
• C107D–BRAKE PEDAL SWITCH 1/2 CORRELATION · C107D–BRAKE PEDAL SWITCH 1/2 CORRELATION For a complete wiring diagram Refer to Section 8W . 1. ENGINE DTCS PRESENT With the scan tool, read Engine DT...
• C1210–G SENSOR INPUT CIRCUIT PERFORMANCE · C1210–G SENSOR INPUT CIRCUIT PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously, with ignition on, until veh...
• C121D-BRAKE PRESSURE SENSOR CIRCUIT · C121D-BRAKE PRESSURE SENSOR CIRCUIT For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: When the ...
• C123B–ESP SYSTEM CONTROL TOO LONG · C123B–ESP SYSTEM CONTROL TOO LONG For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: When the An...
• C123C–DYNAMICS SENSOR MOUNTING/INSTALLATION PERFORMANCE · C123C–DYNAMICS SENSOR MOUNTING/INSTALLATION PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With vehicle speed above 1...
• C2114–DYNAMICS SENSOR SUPPLY VOLTAGE LOW · C2114–DYNAMICS SENSOR SUPPLY VOLTAGE LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: If t...
• C2115–DYNAMICS SENSOR SUPPLY VOLTAGE HIGH · C2115–DYNAMICS SENSOR SUPPLY VOLTAGE HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: Upon ignition on, prior to switching the...
• C2204–DYNAMICS SENSOR INTERNAL · C2204–DYNAMICS SENSOR INTERNAL For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously, with ignition on, until vehicle speed...
• CHECKING TIE ROD ENDS · CHECKING TIE ROD ENDS Tie rod free-play can be measured using the following hand methods: NOTE: When checking free-play, DO NOT rotate the tie rod. Ju...
• CHIME WARNING SYSTEM · CHIME WARNING SYSTEM WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before a...
• CLOCKSPRING CENTERING · CLOCKSPRING CENTERING WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before a...
• CLUTCH · CLUTCH TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Pressure Plate Bolts - 2.8L 31 23 - Pressure Plate Bolts - 3.8L 50 37 - Flywheel Bolts - 2.8L 95 70 - ...
• DESCRIPTION · DESCRIPTION All models have a Vehicle Emission Control Information (VECI) Label. DaimlerChrysler permanently attaches the label in the engine compartm...
• DESCRIPTION · DESCRIPTION DaimlerChrysler Corporation uses international symbols to identify engine compartment lubricant and fluid inspection and fill locations .
• DESCRIPTION · DESCRIPTION Exterior vehicle body colors are identified on the Body Code plate. (Refer to VEHICLE DATA/VEHICLE INFORMATION/BODY CODE PLATE - DESCRIPTI...
• DESCRIPTION · DESCRIPTION If equipped, the Axle Lock switch is located in the Accessory Switch Bezel, below the HVAC controls. The switch will activate the Rear Axl...
• DESCRIPTION · DESCRIPTION Individual Torque Charts appear within many of the Groups. Refer to the Standard Torque Specifications Chart for torque references not lis...
• DESCRIPTION · DESCRIPTION NOTE: On vehicles equipped with a Tire Pressure Monitoring System (TPMS), when the spare tire pressure sensor is replaced with a new press...
• DESCRIPTION · DESCRIPTION The 3.8 Liter (231 cu. in.) engine is 60° V-6 engines with cast iron cylinder blocks and aluminum cylinder heads . The engine uses a singl...
• DESCRIPTION · DESCRIPTION The A/C refrigerant lines and hoses are used to carry the refrigerant between the various A/C system components. The refrigerant lines and...
• DESCRIPTION · DESCRIPTION The SAE bolt strength grades range from grade 2 to grade 8. The higher the grade number, the greater the bolt strength. Identification is ...
• DESCRIPTION · DESCRIPTION The Vehicle Theft Security System (VTSS) is an available factory-installed feature on this vehicle. The VTSS is comprised of two primary s...
• DESCRIPTION · DESCRIPTION The cylinder head covers are made of composite material. The covers are sealed with steel reinforced silicon rubber gaskets. The cylinder ...
• DESCRIPTION · DESCRIPTION The engine oil pressure switch is located on the lower left front side of the engine. It screws into the oil filter adapter. The normally ...
• DESCRIPTION · DESCRIPTION The intake system is made up of an upper and lower intake manifold. The upper intake manifold is made of a composite material for the 3.8L...
• DESCRIPTION · DESCRIPTION The metric system is based on quantities of one, ten, one hundred, one thousand and one million . The following chart will assist in conve...
• DESCRIPTION · DESCRIPTION This section provides illustrations identifying connector, ground, and splice locations in the vehicle. Connector, ground, and splice inde...
• DESCRIPTION · DESCRIPTION This section provides illustrations identifying connector, ground, and splice locations in the vehicle. Connector, ground, and splice inde...
• DESCRIPTION · DESCRIPTION This vehicle is equipped with a Lower Anchors and Tether for CHildren, or LATCH child restraint anchorage system. The second row seats in ...
• DESCRIPTION · DESCRIPTION Under transient cornering conditions the lateral acceleration sensor does not measure the true sway force on the car. In order to compensa...
• DESCRIPTION - FASTENER USAGE · DESCRIPTION - FASTENER USAGE WARNING: USE OF AN INCORRECT FASTENER MAY RESULT IN COMPONENT DAMAGE OR PERSONAL INJURY. Fasteners and torque specificati...
• DESCRIPTION - ROCKER ARMS · DESCRIPTION - ROCKER ARMS The rocker arms are installed on the rocker arm shaft. The rocker arms and shaft assembly is attached to the cylinder head w...
• DIAGNOSIS AND TESTING - AXLE LOCK SWITCH · DIAGNOSIS AND TESTING - AXLE LOCK SWITCH WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, s...
• DIAGNOSIS AND TESTING - HORN SWITCH · DIAGNOSIS AND TESTING - HORN SWITCH For complete circuit diagrams, refer to the appropriate wiring information. WARNING: On vehicles equipped with air...
• DIAGNOSIS AND TESTING - STARTER MOTOR · DIAGNOSIS AND TESTING - STARTER MOTOR Correct starter motor operation can be confirmed by performing the following free running bench test. This test ...
• DIESEL · DIESEL 1. Install the pulley (3) to the pump shaft. 2. Install the three bolts (4) securing the pulley (3) to the pump (2). 3. Install the serpentine ...
• DISASSEMBLY · DISASSEMBLY 1. Remove oil pump cover screws, and lift off cover . 2. Remove oil pump rotors . 3. Clean and inspect oil pump components. (Refer to 9 - ...
• DISASSEMBLY · DISASSEMBLY WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting...
• DISASSEMBLY · DISASSEMBLY WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting...
• DISASSEMBLY · DISASSEMBLY WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting...
• DISASSEMBLY - ROCKER ARMS AND SHAFT · DISASSEMBLY - ROCKER ARMS AND SHAFT CAUTION: Do not attempt to drive the billeted bolt from the rocker shaft. This can damage the rocker arm retainer ...
• ENGINE DIAGNOSIS - MECHANICAL · ENGINE DIAGNOSIS - MECHANICAL CONDITION POSSIBLE CAUSES CORRECTION NOISY VALVES 1. High or low oil level in crankcase. 1. Check and correct engine oil...
• ENGINE OIL · ENGINE OIL WARNING: New or used engine oil can be irritating to the skin. Avoid prolonged or repeated skin contact with engine oil. Contaminants in us...
• FLUID LEVEL CHECK · FLUID LEVEL CHECK The transmission sump has a dipstick to check oil similar to most automatic transmissions. It is located on the left side of the eng...
• FLUID TYPES · FLUID TYPES When service is required, DaimlerChrysler Corporation recommends that only Mopar® brand parts, lubricants and chemicals be used. Mopar® pr...
• FRONT · FRONT WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully inspect all seat bel...
• FRONT · FRONT WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully inspect all seat bel...
• FRONT · FRONT WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any s...
• FRONT · FRONT WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any s...
• FRONT · FRONT WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any st...
• FRONT - FOUR DOOR · FRONT - FOUR DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before atte...
• FRONT - FOUR DOOR · FRONT - FOUR DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before atte...
• FRONT - TWO DOOR · FRONT - TWO DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attem...
• FRONT - TWO DOOR · FRONT - TWO DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attem...
• FRONT AXLE - 186FBI · FRONT AXLE - 186FBI AXLE DESCRIPTION SPECIFICATION Axle Ratio 3.21, 4.10 Ring Gear Backlash 0.12 - 0.20 mm (0.005 - 0.008 in.) Pinion Torque To Rotate...
• FRONT AXLE - 186FBI · FRONT AXLE - 186FBI GEAR NOISE Axle gear noise can be caused by insufficient lubricant, incorrect backlash, tooth contact, worn/damaged gears or the c...
• FRONT AXLE - 186FBI · FRONT AXLE - 186FBI PULLER - C-293-PA ADAPTER C-293-39 ADAPTER C-293-48 FLANGE WRENCH C-3281 PINS C-3288-B DIAL INDICATOR C-3339A INSTALLER C-3716-A I...
• FUSES (TOTALLY INTEGRATED POWER MODULE) · FUSES (TOTALLY INTEGRATED POWER MODULE) The Totally Integrated Power Module (TIPM) is located in the engine compartment near the battery. This center ...
• GRID LINE AND TERMINAL REPAIR · GRID LINE AND TERMINAL REPAIR WARNING: Materials contained in the Repair Kit (Part Number 04549275) may cause skin or eye irritation. The kit contains...
• HEATER HOSES · HEATER HOSES 1. Connect heater core supply hose to heater core and viscous heater. Position hose clamps into proper position. 2. Connect heater core r...
• HIGH PRESSURE RELIEF VALVE · HIGH PRESSURE RELIEF VALVE The high pressure relief valve vents refrigerant from the A/C system when a discharge pressure of 3445 to 4135 kPa (500 to ...
• HOAT COOLANT · HOAT COOLANT WARNING: Antifreeze is an ethylene-glycol base coolant and is harmful if swallowed or inhaled. If swallowed, drink two glasses of water a...
• INSPECTION · INSPECTION Inspect exhaust manifolds for damage or cracks and check distortion of the cylinder head mounting surface and exhaust crossover mounting su...
• INSPECTION · INSPECTION Inspect exhaust manifolds for damage or cracks and check distortion of the cylinder head mounting surface and exhaust crossover mounting su...
• INSPECTION · INSPECTION Inspect the water pump assembly for cracks in the housing, Water leaks from shaft seal, Loose or rough turning bearing or Impeller rubbing ...
• INSTALLATION · INSTALLATION 1. Assemble gasket (1) onto lock cylinder (2) until fully seated. 2. Install lock cylinder (2) into hole in outer door panel. NOTE: Cylin...
• INSTALLATION · INSTALLATION 1. Clean and check condition of throttle body-to-intake manifold O-ring . 2. Clean mating surfaces of throttle body and intake manifold. ...
• INSTALLATION · INSTALLATION 1. Clean axle shaft and apply a thin film of Mopar Wheel Bearing Grease or equivalent to the shaft splines and seal contact surface. 2. I...
• INSTALLATION · INSTALLATION 1. Clean cylinder head and cylinder head cover mating surfaces. Inspect cylinder head cover surface for flatness. Replace gasket as neces...
• INSTALLATION · INSTALLATION 1. Clean cylinder head and cylinder head cover mating surfaces. Inspect cylinder head cover surface for flatness. Replace gasket as neces...
• INSTALLATION · INSTALLATION 1. Clean oil filter adapter and install new seal. 2. Position adapter on engine block and install bolts . 3. Tighten adapter bolts to 28 ...
• INSTALLATION · INSTALLATION 1. Clean relief valve, spring and bore. NOTE: Lubricate relief valve with clean engine oil before installing. 2. Install relief valve and...
• INSTALLATION · INSTALLATION 1. For installation of the steering angle sensor (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/STEERING COLUMN CONTROL MODULE - INS...
• INSTALLATION · INSTALLATION 1. Install air cleaner housing into vehicle and onto the locating pin. 2. Install bolt to hold air cleaner housing to the upper radiator ...
• INSTALLATION · INSTALLATION 1. Install oil baffle in rear bearing cup bore then install rear bearing cup with Installer C-4308 (1) and Handle C-4171 (2). 2. Install ...
• INSTALLATION · INSTALLATION 1. Install oil pressure switch. Torque oil pressure switch to 23 N·m (200 in. lbs.) . 2. Connect electrical connector to switch. 3. Lower...
• INSTALLATION · INSTALLATION 1. Install oil pump. (Refer to 9 - ENGINE/LUBRICATION/OIL PUMP - ASSEMBLY) 2. Install timing chain cover (Refer to 9 - ENGINE/VALVE TIMIN...
• INSTALLATION · INSTALLATION 1. Install pinion rear bearing cup with Installer C-4308 (1) and Driver Handle C-4171 (2). 2. Install pinion front bearing cup with Insta...
• INSTALLATION · INSTALLATION 1. Install rings with manufacturers I.D. mark (if present) facing up, to the top of the piston . CAUTION: Install piston rings in the fol...
• INSTALLATION · INSTALLATION 1. Install the air filter element into air box. 2. Move cover so that the tabs insert into the air cleaner housing. 3. Position the cover...
• INSTALLATION · INSTALLATION 1. Install the cable onto the carrier plate and connect to the latch. 2. Secure the cable clip (3) fully. 3. Connect the cable (1) to the...
• INSTALLATION · INSTALLATION 1. Install the glass (1) into the door (3), front and first. 2. Rotate glass into the correct orientation and push up into the weather se...
• INSTALLATION · INSTALLATION 1. Install the handle (1) and install the front nut (2). 2. Tighten the nut to 4.5 N·m (40 in. lbs.). 3. Install the carrier plate (1), (...
• INSTALLATION · INSTALLATION 1. Install the hub bearing to the knuckle. 2. Install the hub bearing to knuckle and the 3 bolts (3) then tighten to 102 N·m (75 ft. lbs....
• INSTALLATION · INSTALLATION 1. Install the knuckle to the ball joint studs. 2. Install the upper ball joint nut and cotter pin. Tighten to 3. Install the lower ball ...
• INSTALLATION · INSTALLATION 1. Install the load floor carpet (1). 2. Install the rear speaker, (Refer to 8 - ELECTRICAL/AUDIO/SPEAKER - INSTALLATION) . 3. Install th...
• INSTALLATION · INSTALLATION 1. Install the main hard top (4) onto the vehicle and line up the alignment pins. CAUTION: Make sure the B and C-pillar seals are not fol...
• INSTALLATION · INSTALLATION 1. Install the overdrive off switch to the accessory switch bezel. 2. Install the accesory switch bezel (Refer to 23 - BODY/INSTRUMENT PA...
• INSTALLATION · INSTALLATION 1. Install the striker and install the bolts. 2. Adjust the striker (1) and tighten the bolts (2) to 28 N·m (21 ft. lbs.), (Refer to 23 -...
• INSTALLATION · INSTALLATION 1. Install the valve stem seal squarely over the valve guide, using the valve stem as a guide . Do not force the seal against top of the ...
• INSTALLATION · INSTALLATION 1. Install the windshield frame (1) onto the body and install the hinge (3) to body bolts (2). 2. Tighten the hinge bolts (2) to 20 N·m (...
• INSTALLATION · INSTALLATION 1. Lubricate seal and position oil cooler to connector fitting on oil filter adapter . NOTE: Position the flat side of oil cooler paralle...
• INSTALLATION · INSTALLATION 1. Position exhaust manifold on cylinder head . Install bolts to center runner (cylinder #4) and initial tighten to 2.8 N·m (25 in. lbs.)...
• INSTALLATION · INSTALLATION 1. Position exhaust manifold on cylinder head and install bolts to center runner (cylinder # 3) and initial tighten to 2.8 N·m (25 in. lb...
• INSTALLATION · INSTALLATION 1. Position flex plate with backing plate on the crankshaft . 2. Apply Mopar® Lock & Seal Adhesive to the flex plate bolts. 3. Install fl...
• INSTALLATION · INSTALLATION 1. Position new gasket and install retainer on block . Tighten attaching screws to 12 N·m (105 in. lbs.). 2. Install oil pan (Refer to 9 ...
• INSTALLATION · INSTALLATION 1. Position the intrusion module (3) and mounting bracket (4) under the instrument panel as a unit. 2. Reconnect the instrument panel wir...
• INSTALLATION · INSTALLATION 1. Position the regulator (3) onto the carrier plate (1) and install the screws (2). 2. Install the motor (3) and install the screws (1)....
• INSTALLATION · INSTALLATION 1. Wipe oil filter adapter base clean and inspect gasket contact surface. 2. Lubricate gasket of new filter with clean engine oil. 3. Ins...
• INSTALLATION · INSTALLATION CAUTION: Be certain to adjust the refrigerant oil level when servicing the A/C refrigerant system (refer to 24 - HEATING & AIR CONDITIONI...
• INSTALLATION · INSTALLATION CAUTION: Crankshaft oil seal must be removed to insure correct oil pump engagement. 1. Be sure mating surfaces of chain case cover and cy...
• INSTALLATION · INSTALLATION CAUTION: Do not use any type of tool to install the grommets (2). Tools may cut, or tear the grommets creating a leak problem after insta...
• INSTALLATION · INSTALLATION CAUTION: If burr or scratch is present on the crankshaft edge (chamfer), cleanup with 400 grit sand paper to prevent seal damage during i...
• INSTALLATION · INSTALLATION CAUTION: If the A/C compressor is being replaced, be certain to adjust the refrigerant system oil level (refer to 24 - HEATING & AIR COND...
• INSTALLATION · INSTALLATION Front 1. Install the front wheel house liner to front wheel house opening (6). 2. Install the wheel speed sensor harness (1) to the wheel...
• INSTALLATION · INSTALLATION NOTE: Front door latch shown, rear door similar. 1. Install the latch onto the latch bracket tabs (2) and seat fully. 2. Connect the elec...
• INSTALLATION · INSTALLATION NOTE: Front door shown, rear door similar. 1. Position the regulator (3) onto the carrier plate (1) and install the screws (2). NOTE: Fro...
• INSTALLATION · INSTALLATION NOTE: If replacing the spare tire pressure sensor, take the time now to write down the tire pressure sensor ID. NOTE: Before reinstalling...
• INSTALLATION · INSTALLATION NOTE: LHD model shown. RHD model similar. 1. Install the evaporator temperature sensor (1) into the driver side of the HVAC housing (2) ....
• INSTALLATION · INSTALLATION NOTE: Typical A/C compressor and clutch assembly shown in illustrations. 1. Align the dowel pin on the back of the compressor clutch fiel...
• INSTALLATION · INSTALLATION The fuel tank skid plate and the fuel tank assembly are installed at the same. They share common fasteners. 1. If fuel pump module had be...
• INSTALLATION · INSTALLATION WARNING: Allow the urethane at least 24 hours to cure before returning the vehicle to use. CAUTION: Roll down the left and right front do...
• INSTALLATION · INSTALLATION WARNING: Never reuse axle retainer nuts and bolts. Used torque nuts can loosen up. Failure to follow these instruction may result in pers...
• INSTALLATION · INSTALLATION WARNING: On vehicles equipped with airbags, disable the supplemental restraint system before attempting any steering wheel, steering colu...
• INSTALLATION · INSTALLATION WARNING: TTo avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully inspect all s...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemptin...
• INSTALLATION · INSTALLATION WARNING: To avoid personal injury or death, on vehicles equipped with optional seat-mounted side airbags, disable the supplemental restra...
• INSTALLATION · INSTALLATION WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting...
• INSTALLATION · INSTALLATION WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting...
• INSTALLATION - CRANKSHAFT SPROCKET · INSTALLATION - CRANKSHAFT SPROCKET 1. Position the sprocket on the crankshaft (timing mark out) with the timing slot aligned with the timing pin. 2. I...
• INSTALLATION - CYLINDER HEAD · INSTALLATION - CYLINDER HEAD 1. Clean all sealing surfaces of engine block and cylinder heads. (Refer to 9 - ENGINE - STANDARD PROCEDURE) 2. Position ...
• INSTALLATION - CYLINDER HEAD ON · INSTALLATION - CYLINDER HEAD ON 1. The intake valve stem seals should be pushed firmly and squarely over the valve guide using the valve stem as guide...
• INSTALLATION - ENGINE ASSEMBLY · INSTALLATION - ENGINE ASSEMBLY 1. Position the engine in the vehicle. 2. Install both left and right side engine mounts onto engine. 3. Raise the vehi...
• INSTALLATION - LOWER INTAKE MANIFOLD · INSTALLATION - LOWER INTAKE MANIFOLD 1. Place a bead (approximately 1/4 in. diameter) of Mopar® Engine RTV GEN II onto each of the four manifold to cy...
• INSTALLATION - TIMING CHAIN AND CAMSHAFT SPROCKET · INSTALLATION - TIMING CHAIN AND CAMSHAFT SPROCKET 1. Rotate crankshaft so the timing arrow is to the 12 o'clock position . NOTE: Lubricate timing chai...
• INSTALLATION - UPPER INTAKE MANIFOLD · INSTALLATION - UPPER INTAKE MANIFOLD 1. If the following components were removed from manifold, install and tighten to specifications: CAUTION: The sp...
• INSTRUMENT CLUSTER · INSTRUMENT CLUSTER WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before att...
• LAMP · LAMP 1. Disconnect and isolate the battery negative cable. 2. Insert the tip of a small flat bladed screwdriver into the notch (5) between the lens (2...
• LAMP · LAMP 1. Disconnect and isolate the battery negative cable. 2. Insert the tip of a small flat bladed screwdriver into the notch (5) between the lens (2...
• LAMP · LAMP 1. Position the cargo lamp unit (1) to the mounting hole in the sport bar trim. 2. Reconnect the wire harness connector to the connector receptac...
• LAMP · LAMP 1. Position the dome lamp unit (1) to the mounting hole in the rear speaker enclosure. 2. Reconnect the wire harness connector to the connector o...
• LAMP · LAMP WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any st...
• LAMP · LAMP WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any st...
• LAMPS/LIGHTING - EXTERIOR · LAMPS/LIGHTING - EXTERIOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system bef...
• LAMPS/LIGHTING - INTERIOR · LAMPS/LIGHTING - INTERIOR COURTESY LAMPS BULB APPLICATION TABLE LAMP BULB FRONT DOME 578 FRONT MAP/READING 212–2 REAR DOME 212–2 CARGO (WITHOUT REMOVA...
• LAMPS/LIGHTING - INTERIOR · LAMPS/LIGHTING - INTERIOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system bef...
• MAINTENANCE SCHEDULES · MAINTENANCE SCHEDULES There are two maintenance schedules that show the required service for your vehicle. First is Schedule "B" . It is for vehicles ...
• OBD II MONITOR INFORMATION · OBD II MONITOR INFORMATION Comprehensive Components Monitor Major Monitors Non Fuel Control & Non Misfire Major Monitors Fuel Control & misfire (Inclu...
• OBD II MONITOR RUN PROCESS · OBD II MONITOR RUN PROCESS The following procedure has been established to assist technicians in the field with enabling and running OBD II Monitors. ...
• OPERATION · OPERATION High pressures are produced in the refrigerant system when the A/C compressor is operating. Extreme care must be exercised to make sure that...
• OPERATION · OPERATION In the Occupant Classification System (OCS) the passenger airbag on/off indicator gives an indication when the passenger airbag and seat bel...
• OPERATION · OPERATION NOTE: On vehicles equipped with a Tire Pressure Monitoring System (TPMS), when the spare tire pressure sensor is replaced with a new pressur...
• OPERATION · OPERATION SYSTEM 1 - Intake Manifold 2 - Throttle Body 3 - Purge Solenoid 4 - Filter 5 - ESIM 6 - Vapor Canister 7 - Control Valve 8 - Fuel Tank 9 - G...
• OPERATION · OPERATION The Axle Lock switch receives battery current on a fused B(+) circuit from a fuse in the Power Distribution Center (PDC). The switch is grou...
• OPERATION · OPERATION The ESP/BAS indicator gives an indication to the vehicle operator when the Electronic Stability Program (ESP)/Brake Assist System (BAS) has ...
• OPERATION · OPERATION The TCM is the controlling unit for all electronic operations of the transmission. The TCM receives information regarding vehicle operation ...
• OPERATION · OPERATION The Vehicle Theft Security System (VTSS) is divided into two basic subsystems: Vehicle Theft Alarm (VTA) and Sentry Key Immobilizer System (...
• OPERATION · OPERATION The charging system is turned on and off with the ignition switch. The system is on when the engine is running and the ASD relay is energize...
• OPERATION · OPERATION The chime warning system operates on battery voltage received through a fuse in the Totally Integrated Power Module (TIPM) on a non-switched...
• OPERATION · OPERATION The status of the hazard switch is continually monitored by the circuitry within the instrument panel switch pod. The switch pod receives ba...
• OPERATION · OPERATION The turn signal indicators give an indication to the vehicle operator that the turn signal (left or right indicator flashing) or hazard warn...
• OPERATION · OPERATION When the parking brake pedal is pulled the brake cable pulls the brake shoes outward against the brake drum. When the brake pedal is release...
• OPERATION - PUSHRODS · OPERATION - PUSHRODS The pushrod is a solid link between the hydraulic roller lifter and the rocker arm. Also, the pushrod supplies engine oil from th...
• OPERATION - ROCKER ARMS · OPERATION - ROCKER ARMS The rocker arm pivots are on the rocker shaft. Rocker arms are used to translate up and down motions provided by the camshaft,...
• P0457-LOOSE FUEL CAP · P0457-LOOSE FUEL CAP For a complete wiring diagram Refer to Section 8W . Theory of Operation Fuel level is recorded when the ignition key is turned of...
• P0480-COOLING FAN 1 CONTROL CIRCUIT · P0480-COOLING FAN 1 CONTROL CIRCUIT For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage greater ...
• P0481-COOLING FAN 2 CONTROL CIRCUIT · P0481-COOLING FAN 2 CONTROL CIRCUIT For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage greater ...
• P0506-IDLE SPEED PERFORMANCE LOWER THAN EXCEPTED · P0506-IDLE SPEED PERFORMANCE LOWER THAN EXCEPTED For a complete wiring diagram Refer to Section 8W . Theory of Operation The objective of the Idle “Sp...
• P0507-IDLE SPEED PERFORMANCE HIGHER THAN EXCEPTED · P0507-IDLE SPEED PERFORMANCE HIGHER THAN EXCEPTED For a complete wiring diagram Refer to Section 8W . Theory of Operation The objective of the Idle “S...
• P050D-COLD START ROUGH IDLE · P050D-COLD START ROUGH IDLE For a complete wiring diagram Refer to Section 8W Theory of Operation The objective of the Dynamic Crankshaft Fuel Control...
• P0532-A/C PRESSURE SENSOR CIRCUIT LOW · P0532-A/C PRESSURE SENSOR CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: Engine running, AC is learned, and AC Clutch...
• P0533-A/C PRESSURE SENSOR CIRCUIT HIGH · P0533-A/C PRESSURE SENSOR CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: Engine running and the A/C Clutch Relay ene...
• P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW · P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition key on. Set Condition: ...
• P0691-COOLING FAN 1 CONTROL CIRCUIT LOW · P0691-COOLING FAN 1 CONTROL CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage grea...
• P0692-COOLING FAN 1 CONTROL CIRCUIT HIGH · P0692-COOLING FAN 1 CONTROL CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage gre...
• P0693-COOLING FAN 2 CONTROL CIRCUIT LOW · P0693-COOLING FAN 2 CONTROL CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage grea...
• P0694-COOLING FAN 2 CONTROL CIRCUIT HIGH · P0694-COOLING FAN 2 CONTROL CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage gre...
• P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE · P0711-TRANSMISSION TEMPERATURE SENSOR PERFORMANCE For a complete wiring diagram Refer to Section 8W . Theory of Operation The temperature sensor is us...
• P0715-INPUT SPEED SENSOR 1 CIRCUIT · P0715-INPUT SPEED SENSOR 1 CIRCUIT For a complete wiring diagram Refer to Section 8W . Theory of Operation The transmission control system uses two sp...
• P0720-OUTPUT SPEED SENSOR CIRCUIT · P0720-OUTPUT SPEED SENSOR CIRCUIT For a complete wiring diagram Refer to Section 8W . Theory of Operation The transmission system uses two speed senso...
• P0725-ENGINE SPEED SENSOR CIRCUIT · P0725-ENGINE SPEED SENSOR CIRCUIT For a complete wiring diagram Refer to Section 8W . Theory of Operation The PCM uses a dual port RAM internal to the...
• P0740-TCC OUT OF RANGE · P0740-TCC OUT OF RANGE For a complete wiring diagram Refer to Section 8W . Theory of Operation When in 2nd, 3rd, or 4th gear, the Torque Converter Clu...
• P0845-2/4 HYDRAULIC PRESSURE TEST · P0845-2/4 HYDRAULIC PRESSURE TEST For a complete wiring diagram Refer to Section 8W . Theory of Operation Pressure switches are normally off or open (...
• P0882-TCM POWER INPUT LOW · P0882-TCM POWER INPUT LOW For a complete wiring diagram Refer to Section 8W . Theory of Operation The Transmission Control Output circuit is used to s...
• P0883-TCM POWER INPUT HIGH · P0883-TCM POWER INPUT HIGH For a complete wiring diagram Refer to Section 8W . Theory of Operation The Transmission Control Output circuit is used to ...
• P0884-POWER UP AT SPEED · P0884-POWER UP AT SPEED For a complete wiring diagram Refer to Section 8W . Theory of Operation If a vehicle loses power to the PCM, the vehicle will ...
• P0888-TRANSMISSION RELAY ALWAYS OFF · P0888-TRANSMISSION RELAY ALWAYS OFF For a complete wiring diagram Refer to Section 8W . Theory of Operation The Transmission Control Output circuit is...
• P0891-TRANSMISSION RELAY ALWAYS ON · P0891-TRANSMISSION RELAY ALWAYS ON For a complete wiring diagram Refer to Section 8W . Theory of Operation The Transmission Control Output circuit is ...
• P0932-LINE PRESSURE SENSOR CIRCUIT · P0932-LINE PRESSURE SENSOR CIRCUIT For a complete wiring diagram Refer to Section 8W . Theory of Operation Line pressure is electronically controlled ...
• P0934-LINE PRESSURE SENSOR CIRCUIT LOW · P0934-LINE PRESSURE SENSOR CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . Theory of Operation Line pressure is electronically control...
• P0935-LINE PRESSURE SENSOR CIRCUIT HIGH · P0935-LINE PRESSURE SENSOR CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . Theory of Operation Line pressure is electronically contro...
• P0944-LOSS OF HYDRAULIC PUMP PRIME · P0944-LOSS OF HYDRAULIC PUMP PRIME For a complete wiring diagram Refer to Section 8W . Theory of Operation The Loss of Prime Test is used to prevent t...
• P0992-2/4/OD HYDRAULIC PRESSURE TEST · P0992-2/4/OD HYDRAULIC PRESSURE TEST For a complete wiring diagram Refer to Section 8W . Theory of Operation Pressure switches are normally off or ope...
• P128E-TCM POWER CONTROL CIRCUIT 2 OVERCURRENT - TIPM · P128E-TCM POWER CONTROL CIRCUIT 2 OVERCURRENT - TIPM For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery...
• P1897-LEVEL 1 RPM BUS UNLOCK · P1897-LEVEL 1 RPM BUS UNLOCK For a complete wiring diagram Refer to Section 8W . When Monitored: Engine running. Set Condition: When the PCM recognize...
• P2135-THROTTLE POSITION SENSOR 1/2 CORRELATION · P2135-THROTTLE POSITION SENSOR 1/2 CORRELATION For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on and no other D...
• PARK BRAKE SWITCH · PARK BRAKE SWITCH WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before atte...
• PCM/ECM REPROGRAMMING · PCM/ECM REPROGRAMMING MODULE REPROGRAMING Replacement PCM's will require programming utilizing the StarSCAN® or equivalent. The PCM will not operate t...
• PINION DEPTH-BEARING PRELOAD-GEAR BACKLASH · PINION DEPTH-BEARING PRELOAD-GEAR BACKLASH Ring and pinion gears are supplied as matched sets. The identifying numbers for the ring and pinion gear ar...
• PLASTIC BODY PANEL REPAIR · PLASTIC BODY PANEL REPAIR There are many different types of plastics used in today's automotive environment. We group plastics in three different cate...
• POWER STEERING GEAR · POWER STEERING GEAR SPECIFICATIONS DESCRIPTION SPECIFICATION Steering Gear Type Recirculating Ball Steering Gear Overall Ratio 14:1 LWB 16:1 SWB TORQU...
• POWER STEERING PUMP AND HOSES · POWER STEERING PUMP AND HOSES NOTE: This information is designed to be used in conjunction with the diagnostic charts at the beginning of the Steering...
• PRELIMINARY · PRELIMINARY Two basic procedures are required. One procedure for vehicles that are drivable and an alternate procedure for disabled vehicles (will not...
• PRELIMINARY CHECKS · PRELIMINARY CHECKS ENGINE COOLING SYSTEM OVERHEATING Establish what driving conditions caused the complaint. Abnormal loads on the cooling system such...
• PUSHRODS · PUSHRODS The pushrods are made of steel and are a hollow design. The pushrods are positioned between the hydraulic lifter and the rocker arm.
• REAR · REAR WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any ste...
• REAR AXLE - 198RBI · REAR AXLE - 198RBI PULLER C-293-PA ADAPTER C-293-39 ADAPTER C-293-42 PINS C-3288-B DIAL INDICATOR C-3339A INSTALLER C-3716-A INSTALLER C-3718 INSTALLE...
• RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS · RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS ENGINE Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar ® Antifreeze/Coolant 5 Year/1...
• REFRIGERANT SYSTEM RECOVERY · REFRIGERANT SYSTEM RECOVERY WARNING: Refer to the applicable warnings and cautions for this system before performing the following operation (refer to...
• REMOVAL · REMOVAL 1. Disconnect and isolate the battery negative cable. 2. Remove the steering column opening cover from the instrument panel. (Refer to 23 - BO...
• REMOVAL · REMOVAL 1. Disconnect battery negative cable. 2. Disconnect left cylinder bank spark plug wires. 3. Remove heat shield attaching bolts . 4. Remove bol...
• REMOVAL · REMOVAL 1. Disconnect battery negative cable. 2. Raise and support the vehicle. 3. Separate the exhaust pipe at the exhaust manifold. 4. Lower the veh...
• REMOVAL · REMOVAL 1. Disconnect negative cable from battery. 2. Disconnect spark plug wires from plugs. 3. Disconnect PCV hose from cylinder head cover . 4. Rem...
• REMOVAL · REMOVAL 1. Disconnect spark plug wires from spark plugs. 2. Disconnect crankcase vent hose from cylinder head cover. 3. Remove cylinder head cover bol...
• REMOVAL · REMOVAL 1. Disconnect the IAT sensor. 2. Disconnect the CCV hose. 3. Separate the air inlet tube from the throttle body. 4. Remove the air cleaner cov...
• REMOVAL · REMOVAL 1. Disconnect the negative battery cable. 2. Disconnect the inlet air temperature sensor. 3. Disconnect the CCV hose from the air cleaner cove...
• REMOVAL · REMOVAL 1. Drain cooling system (Refer to 7 - COOLING - STANDARD PROCEDURE - COOLING SYSTEM DRAINING) . 2. Disconnect oil cooler inlet and outlet hose...
• REMOVAL · REMOVAL 1. For removal of the steering angle sensor (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES/STEERING COLUMN CONTROL MODULE - REMOVAL) .
• REMOVAL · REMOVAL 1. From inside the vehicle, release the center clamps (2). 2. Release the rear clamps (3). 3. Remove the rear thumb bolts (6). 4. Release the ...
• REMOVAL · REMOVAL 1. Open the tail gate. 2. Using a grease pencil or equivalent, mark the location of the stabilizer cup (1) and insert to aid installation. 3. ...
• REMOVAL · REMOVAL 1. Perform the fuel pressure relief procedure (Refer to 14 - FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE) . 2. Disconnect negative cable fr...
• REMOVAL · REMOVAL 1. Position the glass into the down position. 2. Remove the door trim panel, (Refer to 23 - BODY/DOOR - FULL FRONT/TRIM PANEL - REMOVAL) . 3. ...
• REMOVAL · REMOVAL 1. Raise and support vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE) 2. Remove the tire and wheel assembly (Refer ...
• REMOVAL · REMOVAL 1. Raise vehicle on hoist. 2. Disconnect electrical connector from switch. 3. Remove oil pressure switch .
• REMOVAL · REMOVAL 1. Raise vehicle on hoist. 2. Remove the oil filter. 3. Disconnect oil pressure switch electrical connector. 4. Remove oil filter adapter atta...
• REMOVAL · REMOVAL 1. Remove air duct and air resonator box at throttle body (1). 2. Disconnect electrical connector (3) at throttle body. 3. Remove four throttl...
• REMOVAL · REMOVAL 1. Remove axle shaft from vehicle. NOTE: It is normal that the axle bearing race is loose in the axle tube. 2. Remove brake dust shield (1) an...
• REMOVAL · REMOVAL 1. Remove electric cooling fan (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL) . 2. Position cooling fan out of the way. 3. Remove the tr...
• REMOVAL · REMOVAL 1. Remove the accessory switch bezel (Refer to 23 - BODY/INSTRUMENT PANEL/ACCESSORY SWITCH BEZEL - REMOVAL) . 2. Remove the overdrive off swit...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL FRONT/CARRIER PLATE - REMOVAL) . 2. Release the cable clip at the inside hand...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL FRONT/CARRIER PLATE - REMOVAL) . 2. Remove the clip (3) and separate the lock...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL FRONT/CARRIER PLATE - REMOVAL) . 2. Remove the nut (2) and position the run c...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL FRONT/CARRIER PLATE - REMOVAL) . 2. Remove the nut (2) and remove the handle ...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL FRONT/CARRIER PLATE - REMOVAL) . 2. Remove the screws (1) and disconnect the ...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL FRONT/CARRIER PLATE - REMOVAL) . NOTE: Front door shown, rear door similar. 2...
• REMOVAL · REMOVAL 1. Remove the carrier plate (1), (Refer to 23 - BODY/DOOR - FULL REAR/CARRIER PLATE - REMOVAL) . NOTE: Front door shown, rear door similar. 2....
• REMOVAL · REMOVAL 1. Remove the radiator and cooling fans from the vehicle. 2. Remove the cylinder heads (Refer to 9 - ENGINE/CYLINDER HEAD - REMOVAL) . 3. Remo...
• REMOVAL · REMOVAL 1. Remove the transmission (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 41TE - REMOVAL) . 2. Remove flex plate attaching bolts. 3. Remove...
• REMOVAL · REMOVAL 1. Remove the transmission (Refer to 21 - TRANSMISSION/TRANSAXLE/AUTOMATIC - 41TE - REMOVAL) . 2. Remove the flex plate. (Refer to 9 - ENGINE/...
• REMOVAL · REMOVAL 1. Remove the valve springs. (Refer to 9 - ENGINE/CYLINDER HEAD/VALVE SPRINGS - REMOVAL) 2. Remove the valve stem seal .
• REMOVAL · REMOVAL 1. With transmission in neutral, position vehicle on hoist. 2. Remove brake caliper with adapter and rotor. 3. Remove park brake cable (1) fro...
• REMOVAL · REMOVAL 4 DOOR EXPLODED VIEW 1 - RIGHT SIDE SPORT BAR 2 - REAR CROSS BAR 3 - REAR CROSS BAR BRACKETS 4 - REAR CROSS BAR BRACKETS BOLTS 19 N·m (14 ft. ...
• REMOVAL · REMOVAL Front 1. Raise and support the vehicle (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE) . 2. Remove the wheel and tire to ga...
• REMOVAL · REMOVAL Front 1. Remove the rivets (1) securing the fender flares (4) to the support (3). 2. Using a trim stick C-4755 or equivalent, separate the cli...
• REMOVAL · REMOVAL NOTE: Front door trim shown, rear door similar. 1. Position the glass into the down position. 2. Remove the trim panel (1), (Refer to 23 - BOD...
• REMOVAL · REMOVAL NOTE: LHD model shown. RHD model similar. 1. Remove the HVAC housing assembly and place it on a workbench (refer to 24 - HEATING & AIR CONDITI...
• REMOVAL · REMOVAL NOTE: The compressor clutch assembly can be serviced with the refrigerant system fully-charged. NOTE: Typical A/C compressor and clutch assemb...
• REMOVAL · REMOVAL The ESIM (EVAP System Integrity Monitor) switch is attached to the EVAP canister and is usually not serviceable. Replace the switch by replaci...
• REMOVAL · REMOVAL The oil pump is contained within the timing chain cover housing. 1. Remove oil pan. (Refer to 9 - ENGINE/LUBRICATION/OIL PAN - REMOVAL) 2. Rem...
• REMOVAL · REMOVAL WARNING: On vehicles equipped with airbags, disable the supplemental restraint system before attempting any steering wheel, steering column, d...
• REMOVAL · REMOVAL WARNING: Refer to the applicable warnings and cautions for this system before performing the following operation (refer to 24 - HEATING & AIR ...
• REMOVAL · REMOVAL WARNING: The fuel system is under constant pressure even with engine off. Before servicing fuel rail, fuel system pressure must be released. 1...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully inspect all seat b...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any...
• REMOVAL · REMOVAL WARNING: To avoid personal injury or death, on vehicles equipped with optional seat-mounted side airbags, disable the supplemental restraint s...
• REMOVAL · REMOVAL WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any ...
• REMOVAL · REMOVAL WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any ...
• REMOVAL · REMOVAL WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system before attempting any ...
• REMOVAL - CRANKSHAFT SPROCKET · REMOVAL - CRANKSHAFT SPROCKET 1. Remove the timing chain. (Refer to 9 - ENGINE/VALVE TIMING/TIMING BELT/CHAIN AND SPROCKETS - REMOVAL) 2. Using Specia...
• REMOVAL - CYLINDER HEAD · REMOVAL - CYLINDER HEAD 1. Drain the cooling system. (Refer to 7 - COOLING - STANDARD PROCEDURE) 2. Disconnect negative cable from battery. 3. Remove ...
• REMOVAL - CYLINDER HEAD ON · REMOVAL - CYLINDER HEAD ON 1. Disconnect negative cable from battery. 2. Remove spark plug wires and all spark plugs. 3. Remove cylinder head cover(s)...
• REMOVAL - ENGINE ASSEMBLY · REMOVAL - ENGINE ASSEMBLY 1. Perform fuel pressure release procedure (Refer to 14 - FUEL SYSTEM/FUEL DELIVERY - STANDARD PROCEDURE) . 2. Disconnect ne...
• REMOVAL - LOWER INTAKE MANIFOLD · REMOVAL - LOWER INTAKE MANIFOLD 1. Perform fuel system pressure release procedure (before attempting any repairs). (Refer to 14 - FUEL SYSTEM/FUEL DEL...
• REMOVAL - TIMING CHAIN AND CAMSHAFT SPROCKET · REMOVAL - TIMING CHAIN AND CAMSHAFT SPROCKET 1. Disconnect negative cable from battery. 2. Remove the timing chain cover. (Refer to 9 - ENGINE/VALVE T...
• REMOVAL - UPPER INTAKE MANIFOLD · REMOVAL - UPPER INTAKE MANIFOLD 1. Disconnect battery negative cable. 2. Disconnect inlet air temperature (IAT) sensor electrical connector. 3. Remove...
• RIGHT MULTI-FUNCTION SWITCH · RIGHT MULTI-FUNCTION SWITCH WARNING: To avoid serious or fatal injury, on vehicles equipped with airbags, disable the supplemental restraint system be...
• ROCKER ARMS AND SHAFT · ROCKER ARMS AND SHAFT 1. Remove the cylinder head cover(s). (Refer to 9 - ENGINE/CYLINDER HEAD/CYLINDER HEAD COVER(S) - REMOVAL) NOTE: Rocker arm shaf...
• ROCKER ARMS AND SHAFT · ROCKER ARMS AND SHAFT CAUTION: Ensure the longer shaft retaining bolt is installed in the proper location on the rocker shaft. (Refer to 9 - ENGINE/CY...
• SECOND ROW - CENTER AND LEFT - FOUR DOOR · SECOND ROW - CENTER AND LEFT - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor serv...
• SECOND ROW - CENTER AND LEFT - FOUR DOOR · SECOND ROW - CENTER AND LEFT - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor serv...
• SECOND ROW - RIGHT - FOUR DOOR · SECOND ROW - RIGHT - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, caref...
• SECOND ROW - RIGHT - FOUR DOOR · SECOND ROW - RIGHT - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, caref...
• SECOND ROW - TWO DOOR · SECOND ROW - TWO DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully insp...
• SECOND ROW - TWO DOOR · SECOND ROW - TWO DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully insp...
• SECOND ROW - TWO DOOR · SECOND ROW - TWO DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully insp...
• SECOND ROW - TWO DOOR · SECOND ROW - TWO DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefully insp...
• SECOND ROW CENTER - FOUR DOOR · SECOND ROW CENTER - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefu...
• SECOND ROW CENTER - FOUR DOOR · SECOND ROW CENTER - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefu...
• SECOND ROW OUTBOARD - FOUR DOOR · SECOND ROW OUTBOARD - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, care...
• SECOND ROW OUTBOARD - FOUR DOOR · SECOND ROW OUTBOARD - FOUR DOOR WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, care...
• SERVICE AFTER A SUPPLEMENTAL RESTRAINT DEPLOYMENT · SERVICE AFTER A SUPPLEMENTAL RESTRAINT DEPLOYMENT Any vehicle which is to be returned to use following a supplemental restraint deployment, must have ...
• SIDE - FOUR-DOOR · SIDE - FOUR-DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attem...
• SIDE - FOUR-DOOR · SIDE - FOUR-DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attem...
• SIDE - TWO-DOOR · SIDE - TWO-DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemp...
• SIDE - TWO-DOOR · SIDE - TWO-DOOR WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system before attemp...
• SPECIFICATIONS - FLUID CAPACITIES · SPECIFICATIONS - FLUID CAPACITIES DESCRIPTION SPECIFICATION FUEL TANK - 3.8L Gas Engine - 2 door models 18.6 U.S. Gallons (70.4 Liters)**** FUEL TANK ...
• SPECIFICATIONS - TORQUE · SPECIFICATIONS - TORQUE Description N·m Ft. Lbs In. Lbs. A/c expansion valve nut 23 17 — Backlite hinge bolts 10 — 90 Body isolator mounting bolts 108...
• STANDARD PROCEDURE - ENGINE OIL AND FILTER CHANGE · STANDARD PROCEDURE - ENGINE OIL AND FILTER CHANGE Change engine oil at mileage and time intervals described in the Maintenance Schedule. (Refer to LUB...
• STANDARD PROCEDURE - FITTING PISTONS · STANDARD PROCEDURE - FITTING PISTONS NOTE: Pistons and connecting rods are machined to tight weight tolerances and need not be sorted in any way. The ...
• STANDARD PROCEDURE - INTAKE MANIFOLD VACUUM PORT REPAIR · STANDARD PROCEDURE - INTAKE MANIFOLD VACUUM PORT REPAIR The composite intake manifold vacuum ports can be repaired. Although, if the manifold plenum c...
• STANDARD PROCEDURE - MAIN BEARING FITTING · STANDARD PROCEDURE - MAIN BEARING FITTING Bearing caps are not interchangeable and should be marked at removal to insure correct assembly . Upper and ...
• STANDARD PROCEDURE - MEASURING CONNECTING ROD BEARING CLEARANCE · STANDARD PROCEDURE - MEASURING CONNECTING ROD BEARING CLEARANCE CAUTION: Two styles of connecting rod with bearing caps are available (standard forged...
• STANDARD PROCEDURE - MEASURING TIMING CHAIN WEAR · STANDARD PROCEDURE - MEASURING TIMING CHAIN WEAR NOTE: This procedure must be performed with the timing chain cover removed (Refer to 9 - ENGINE/VALVE...
• STANDARD PROCEDURE - PISTON RING FITTING · STANDARD PROCEDURE - PISTON RING FITTING 1. Wipe cylinder bore clean. Insert the ring and push down with piston to ensure squareness in bore to approx...
• STANDARD PROCEDURE - QUICK-CONNECT FITTINGS · STANDARD PROCEDURE - QUICK-CONNECT FITTINGS Different types of quick-connect fittings are used to attach the various fuel system components, lines and...
• STANDARD PROCEDURE - TRANSMISSION COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/ASSEMBLY · STANDARD PROCEDURE - TRANSMISSION COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/ASSEMBLY DISCONNECT 1. Remove dust cap by pulling it straight back off...
• STARTING SYSTEM · STARTING SYSTEM The battery, starting, and charging systems operate in conjunction with one another, and must be tested as a complete system. For corr...
• STEERING CONTROL MODULE · STEERING CONTROL MODULE WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental restraint system befor...
• STEERING SYSTEM DIAGNOSIS CHARTS · STEERING SYSTEM DIAGNOSIS CHARTS NOTE: There are three diagnosis charts following that cover NOISE, VIBRATION AND HARSHNESS (NVH) ISSUES, PERFORMANCE ...
• SUPPLEMENTAL RESTRAINT SYSTEM · SUPPLEMENTAL RESTRAINT SYSTEM The hard wired circuits between modules and components related to the Supplemental Restraint System (SRS) may be diagnos...
• SUPPLEMENTAL RESTRAINTS VERIFICATION TEST · SUPPLEMENTAL RESTRAINTS VERIFICATION TEST NOTE: The following procedure should be performed using a diagnostic scan tool to verify proper supplemental...
• T0RQUE CHART · T0RQUE CHART TORQUE SPECIFICATIONS DESCRIPTION N·m Ft. Lbs. In. Lbs. Hydraulic Control Unit Bracket to HCU Bolts 6.5 — 57 Hydraulic Control Unit Body ...
• TIE ROD · TIE ROD Tie rod free-play can be measured using the following hand methods: NOTE: When checking free-play, DO NOT rotate the tie rod. Just because a t...
• TIRE AND WHEEL RUNOUT · TIRE AND WHEEL RUNOUT Radial runout is the difference between the high and low points on the tire or wheel. Lateral runout is the wobble of the tire o...
• TORQUE · TORQUE DESCRIPTION N·m Ft. In. Lbs. Lbs. Bolts, Crossmember to Sill 42 31 - Nuts, Crossmember to Transmission Mount 22 16 - Nuts/Bolt, Exhaust Manifol...
• TORQUE · TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. 3.8L Camshaft Sensor Bolt 14.1 125 3.8L Ignition coil bolts 11.8 105 Spark Plugs 17.5 13 Knock Sensor 10 7
• TORQUE · TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Shock Absorber Upper Bolts 50 37 — Shock Absorber Lower Nut 76 56 — Suspension Arm Lower Axle Bracket Nut 169...
• TORQUE · TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Shock Absorber Upper Nut 27 20 — Shock Absorber Lower Nut 76 56 — Suspension Arm Lower Axle Bracket Nut 169 1...
• TORQUE · TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Tire Pressure Sensor/Transmitter Mounting Nut 8 — 71
• TORQUE · TORQUE Description N·m Ft. Lbs. In. Lbs. All Screws NOT Listed Below 1.2 – 10 A/C Compressor Bolts 54 40 – A/C Compressor Shaft Nut 19 14 168 A/C Cond...
• TORQUE - 3.8L GAS · TORQUE - 3.8L GAS DESCRIPTION N·m Ft. Lbs. In. Lbs. Accelerator Pedal Bracket Mounting 12 - 105 Crankshaft Position Sensor - 3.8L 28 21 - Camshaft Pos...
• TORQUE CHART · TORQUE CHART DESCRIPTION N·m Ft. Lbs. In. Lbs. Power Steering Gear Adjustment Screw Locknut 65 48 — Power Steering Gear Gear to Frame Bolts 108 870 — ...
• TORQUE CHART · TORQUE CHART SPECIFICATIONS DESCRIPTION N·m Ft. Lbs. In. Lbs. Lug Nut 1/2 X 20 with 60° Cone 115-170 85-125 — Spare Wheel Lug Nut 54–108 40–80 —
• TORQUE CHART · TORQUE CHART TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Brake Booster Mounting Nuts 25 18 — Master Cylinder Mounting Nuts 17 13 151 Booster Mounting Pla...
• TORQUE CHART · TORQUE CHART TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Power Steering Pump to engine 26 19 — Power Steering Pump Pulley Diesel 28 21 — Power Steering P...
• TORQUE CHART · TORQUE CHART TORQUE DESCRIPTION N·m Ft. Lbs. In. Lbs. Steering Column Steering Wheel Nut 54 40 — Steering Column Mounting Nuts 17 — 150 Intermediate S...
• TORQUE CHART · TORQUE CHART TORQUE SPECIFICATIONS DESCRIPTION N·m Ft. Lbs. In. Lbs. Pitman Arm Shaft 251 185 — Drag Link Ball Stud to Pitman Arm 105 77 — Drag Link B...
• TRANSFER CASE - NV231 · TRANSFER CASE - NV231 Recommended lubricant for the NV231 transfer case is Mopar® ATF +4, Automatic Transmission Fluid.
• U0002-CAN C BUS OFF PERFORMANCE · U0002-CAN C BUS OFF PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: The Occupant ...
• U0019-CAN B BUS · U0019-CAN B BUS For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition: Whenever the CAN B Bus (+) or CAN B Bu...
• U0019-CAN B BUS · U0019-CAN B BUS For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition: Whenever the CAN B Bus (+) or CAN B Bu...
• U0019–CAN B BUS · U0019–CAN B BUS For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously. Set Condition: Whenever the CAN B BUS (+) or B BUS (...
• U0020-CAN B BUS OFF PERFORMANCE · U0020-CAN B BUS OFF PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously Set Condition: Whenever the CAN B Bus...
• U0020-CAN B BUS OFF PERFORMANCE · U0020-CAN B BUS OFF PERFORMANCE For a complete wiring diagram Refer to Section 8W . When Monitored: Continuously. Set Condition: Whenever the CAN B BU...
• U0022-CAN B BUS (+) CIRCUIT LOW · U0022-CAN B BUS (+) CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AN...
• U0023-CAN B BUS (+) CIRCUIT HIGH · U0023-CAN B BUS (+) CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS A...
• U0025-CAN B BUS (-) CIRCUIT LOW · U0025-CAN B BUS (-) CIRCUIT LOW For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AN...
• U0026-CAN B BUS (-) CIRCUIT HIGH · U0026-CAN B BUS (-) CIRCUIT HIGH For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS A...
• U0100-LOST COMMUNICATION WITH ECM/PCM · U0100-LOST COMMUNICATION WITH ECM/PCM For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage betwee...
• U0100–LOST COMMUNICATION WITH ECM/PCM · U0100–LOST COMMUNICATION WITH ECM/PCM For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on Battery voltage between...
• U0101-LOST COMMUNICATION WITH TCM · U0101-LOST COMMUNICATION WITH TCM For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery voltage between 10...
• U0114-LOST COMMUNICATION WITH FINAL DRIVE CONTROL MODULE (FDCM) · U0114-LOST COMMUNICATION WITH FINAL DRIVE CONTROL MODULE (FDCM) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition ...
• U0121-LOST COMMUNICATION WITH ANTI-LOCK BRAKE MODULE · U0121-LOST COMMUNICATION WITH ANTI-LOCK BRAKE MODULE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Battery...
• U0125–LOST COMMUNICATION WITH DYNAMICS SENSOR · U0125–LOST COMMUNICATION WITH DYNAMICS SENSOR For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition:...
• U0126-LOST COMMUNICATION WITH STEERING ANGLE SENSOR (SAS) · U0126-LOST COMMUNICATION WITH STEERING ANGLE SENSOR (SAS) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Ba...
• U0141–LOST COMMUNICATION WITH FRONT CONTROL MODULE · U0141–LOST COMMUNICATION WITH FRONT CONTROL MODULE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on Battery vo...
• U0146–LOST COMMUNICATION WITH CENTRAL GATEWAY · U0146–LOST COMMUNICATION WITH CENTRAL GATEWAY For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on Battery voltage...
• U0151-LOST COMMINICATION WITH OCCUPANT RESTRAINT CONTROLLER · U0151-LOST COMMINICATION WITH OCCUPANT RESTRAINT CONTROLLER For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CO...
• U0151-LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER · U0151-LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CO...
• U0151–LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER (ORC) · U0151–LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER (ORC) For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignitio...
• U0154-LOST COMMINICATION WITH OCCUPANT CLASSIFICATION MODULE · U0154-LOST COMMINICATION WITH OCCUPANT CLASSIFICATION MODULE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC C...
• U0154–LOST COMMUNICATION WITH OCCUPANT CLASSIFICATION MODULE · U0154–LOST COMMUNICATION WITH OCCUPANT CLASSIFICATION MODULE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on....
• U0168-LOST COMMUNICATION WITH SKREEM · U0168-LOST COMMUNICATION WITH SKREEM For a complete wiring diagram Refer to Section 8W . When Monitored: Ignition run time is greater than 1 second. B...
• U0168-LOST COMMUNICATION WITH VEHICLE SECURITY CONTROL MODULE (SKREEM/WCM) · U0168-LOST COMMUNICATION WITH VEHICLE SECURITY CONTROL MODULE (SKREEM/WCM) For a complete wiring diagram Refer to Section 8W . When Monitored: With th...
• U0170-LOST COMMUNICATION W/UP-FRONT LEFT SATELLITE ACCELERATION SENSOR · U0170-LOST COMMUNICATION W/UP-FRONT LEFT SATELLITE ACCELERATION SENSOR For a complete wiring diagram Refer to Section 8W . When Monitored: The Occupan...
• U0171-LOST COMMUNICATION W/UP-FRONT RIGHT SATELLITE ACCELERATION SENSOR · U0171-LOST COMMUNICATION W/UP-FRONT RIGHT SATELLITE ACCELERATION SENSOR For a complete wiring diagram Refer to Section 8W . When Monitored: The Occupa...
• U0172-LOST COMMUNICATION W/LEFT SIDE SATELLITE ACCELERATION SENSOR 1 · U0172-LOST COMMUNICATION W/LEFT SIDE SATELLITE ACCELERATION SENSOR 1 For a complete wiring diagram Refer to Section 8W . When Monitored: The Occupant ...
• U0175-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION SENSOR 1 · U0175-LOST COMMUNICATION W/RIGHT SIDE SATELLITE ACCELERATION SENSOR 1 For a complete wiring diagram Refer to Section 8W . When Monitored: The Occupant...
• U0197-LOST COMMINICATION WITH HANDS FREE MODULE · U0197-LOST COMMINICATION WITH HANDS FREE MODULE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULE...
• U0197-LOST COMMUNICATION WITH HANDS FREE PHONE · U0197-LOST COMMUNICATION WITH HANDS FREE PHONE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES...
• U0199-LOST COMMINICATION WITH DRIVERS DOOR MODULE · U0199-LOST COMMINICATION WITH DRIVERS DOOR MODULE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODU...
• U0199-LOST COMMUNICATION WITH DRIVER DOOR MODULE · U0199-LOST COMMUNICATION WITH DRIVER DOOR MODULE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODUL...
• U0200-LOST COMMINICATION WITH PASSENGER DOOR MODULE · U0200-LOST COMMINICATION WITH PASSENGER DOOR MODULE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MO...
• U0200-LOST COMMUNICATION WITH PASSENGER DOOR MODULE · U0200-LOST COMMUNICATION WITH PASSENGER DOOR MODULE For a complete wiring diagram Refer to Section 8W . (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MO...
• U1008–LIN 1 BUS · U1008–LIN 1 BUS For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Condition: LIN 1 Bus Performance. Possib...
• U113B-LOST COMMUNICATION WITH SWITCH BANK MODULE · U113B-LOST COMMUNICATION WITH SWITCH BANK MODULE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. Set Conditi...
• U1159-LOST COMMUNICATION WITH AUTOMATIC SWAY BAR SYSTEM (ASBS) MODULE · U1159-LOST COMMUNICATION WITH AUTOMATIC SWAY BAR SYSTEM (ASBS) MODULE For a complete wiring diagram Refer to Section 8W . When Monitored: With the ign...
• U1414-IMPLAUSIBLE/MISSING ECU CONFIGURATION DATA · U1414-IMPLAUSIBLE/MISSING ECU CONFIGURATION DATA For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. The Occupan...
• U1415-IMPLAUSIBLE/MISSING VEHICLE CONFIGURATION DATA · U1415-IMPLAUSIBLE/MISSING VEHICLE CONFIGURATION DATA For a complete wiring diagram Refer to Section 8W . When Monitored: With the ignition on. The Occ...
• U1502–IMPLAUSIBLE MESSAGE DATA LENGTH RECEIVED FROM TCM · U1502–IMPLAUSIBLE MESSAGE DATA LENGTH RECEIVED FROM TCM For a complete wiring diagram Refer to Section 8W When Monitored: Continuously, with ignition ...
• VEHICLE THEFT SECURITY SYSTEM · VEHICLE THEFT SECURITY SYSTEM The Vehicle Theft Security System (VTSS) is divided into two basic subsystems: Vehicle Theft Alarm (VTA) and Sentry Key ...
• WARNING · WARNING WARNING: The A/C system contains refrigerant under high pressure. Repairs should only be performed by qualified service personnel. Severe pers...
• WARNINGS - LAMPS/LIGHTING - EXTERIOR · WARNINGS - LAMPS/LIGHTING - EXTERIOR WARNING: To avoid personal injury or death, eye protection should be used when servicing any glass components. CA...
• WARNINGS - LAMPS/LIGHTING - INTERIOR · WARNINGS - LAMPS/LIGHTING - INTERIOR WARNING: To avoid personal injury or death, eye protection should be used when servicing any glass components. CA...
• WARNINGS - RESTRAINT SYSTEM · WARNINGS - RESTRAINT SYSTEM WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor service, carefull...
• WELD LOCATIONS · WELD LOCATIONS DESCRIPTION FIGURE UNDERBODY/HYDROFORM COMPLETE UNDERBODY/HYDROFORM COMPLETE COWL/DASH/PLENUM (1 OF 4) COWL/DASH/PLENUM (1 OF 4) COWL/D...
• WELD NUT SERVICE · WELD NUT SERVICE SERVICE LOCATIONS 1 - THREE M10 FUEL VAPOR CANISTER CROSSMEMBER NUTS ACCESS HOLES LOCATED ON TOP OF CROSSMEMBERS 2 - TWO M12 TRANSMIS...
• WHEEL DESIGN · WHEEL DESIGN The rim size is on the vehicle safety certification label located on the drivers door shut face. The size of the rim is determined by the...
• WHEEL INSTALLATION · WHEEL INSTALLATION The wheel studs and nuts are designed for specific applications. They must be replaced with equivalent parts. Do not use replacemen...
• WIRELESS CONTROL MODULE (WCM) · WIRELESS CONTROL MODULE (WCM) The receiver circuit for the TPM system is integrated into the WCM. The WCM also includes the Remote Keyless Entry (RKE)...